Debian Codegraph @

scripts/dtc/include-prefixes/arm64/rockchip/rk3399-roc-pc.dtsi

raw
1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2 /*
3 * Copyright (c) 2017 T-Chip Intelligent Technology Co., Ltd
4 */
5
6 /dts-v1/;
7 #include <dt-bindings/input/linux-event-codes.h>
8 #include <dt-bindings/pwm/pwm.h>
9 #include "rk3399.dtsi"
10
11 / {
12 model = "Firefly ROC-RK3399-PC Board";
13 compatible = "firefly,roc-rk3399-pc", "rockchip,rk3399";
14
15 aliases {
16 ethernet0 = &gmac;
17 mmc0 = &sdmmc;
18 mmc1 = &sdhci;
19 };
20
21 chosen {
22 stdout-path = "serial2:1500000n8";
23 };
24
25 backlight: backlight {
26 compatible = "pwm-backlight";
27 pwms = <&pwm0 0 25000 0>;
28 };
29
30 clkin_gmac: external-gmac-clock {
31 compatible = "fixed-clock";
32 clock-frequency = <125000000>;
33 clock-output-names = "clkin_gmac";
34 #clock-cells = <0>;
35 };
36
37 adc-keys {
38 compatible = "adc-keys";
39 io-channels = <&saradc 1>;
40 io-channel-names = "buttons";
41 keyup-threshold-microvolt = <1500000>;
42 poll-interval = <100>;
43
44 button-recovery {
45 label = "Recovery";
46 linux,code = <KEY_VENDOR>;
47 press-threshold-microvolt = <18000>;
48 };
49 };
50
51 gpio-keys {
52 compatible = "gpio-keys";
53 autorepeat;
54 pinctrl-names = "default";
55 pinctrl-0 = <&pwr_key_l>;
56
57 key-power {
58 debounce-interval = <100>;
59 gpios = <&gpio0 RK_PA5 GPIO_ACTIVE_LOW>;
60 label = "GPIO Key Power";
61 linux,code = <KEY_POWER>;
62 wakeup-source;
63 };
64 };
65
66 ir-receiver {
67 compatible = "gpio-ir-receiver";
68 gpios = <&gpio0 RK_PA6 GPIO_ACTIVE_LOW>;
69 pinctrl-names = "default";
70 pinctrl-0 = <&ir_int>;
71 };
72
73 leds {
74 compatible = "gpio-leds";
75 pinctrl-names = "default";
76 pinctrl-0 = <&work_led_pin>, <&diy_led_pin>, <&yellow_led_pin>;
77
78 work_led: led-0 {
79 label = "green:work";
80 gpios = <&gpio2 RK_PD3 GPIO_ACTIVE_HIGH>;
81 default-state = "on";
82 linux,default-trigger = "heartbeat";
83 };
84
85 diy_led: led-1 {
86 label = "red:diy";
87 gpios = <&gpio0 RK_PB5 GPIO_ACTIVE_HIGH>;
88 default-state = "off";
89 linux,default-trigger = "mmc2";
90 };
91
92 yellow_led: led-2 {
93 label = "yellow:yellow-led";
94 gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_HIGH>;
95 default-state = "off";
96 linux,default-trigger = "mmc1";
97 };
98 };
99
100 sdio_pwrseq: sdio-pwrseq {
101 compatible = "mmc-pwrseq-simple";
102 clocks = <&rk808 1>;
103 clock-names = "ext_clock";
104 pinctrl-names = "default";
105 pinctrl-0 = <&wifi_enable_h>;
106
107 /*
108 * On the module itself this is one of these (depending
109 * on the actual card populated):
110 * - SDIO_RESET_L_WL_REG_ON
111 * - PDN (power down when low)
112 */
113 reset-gpios = <&gpio0 RK_PB2 GPIO_ACTIVE_LOW>;
114 };
115
116 vcc_vbus_typec0: regulator-vcc-vbus-typec0 {
117 compatible = "regulator-fixed";
118 regulator-name = "vcc_vbus_typec0";
119 regulator-always-on;
120 regulator-boot-on;
121 regulator-min-microvolt = <5000000>;
122 regulator-max-microvolt = <5000000>;
123 };
124
125 sys_12v: regulator-sys-12v {
126 compatible = "regulator-fixed";
127 regulator-name = "sys_12v";
128 regulator-always-on;
129 regulator-boot-on;
130 vin-supply = <&dc_12v>;
131 };
132
133 /* switched by pmic_sleep */
134 vcc1v8_s3: vcca1v8_s3: regulator-vcc1v8-s3 {
135 compatible = "regulator-fixed";
136 regulator-name = "vcc1v8_s3";
137 regulator-always-on;
138 regulator-boot-on;
139 regulator-min-microvolt = <1800000>;
140 regulator-max-microvolt = <1800000>;
141 vin-supply = <&vcc_1v8>;
142 };
143
144 vcc3v0_sd: regulator-vcc3v0-sd {
145 compatible = "regulator-fixed";
146 enable-active-high;
147 gpio = <&gpio4 RK_PD6 GPIO_ACTIVE_HIGH>;
148 pinctrl-names = "default";
149 pinctrl-0 = <&vcc3v0_sd_en>;
150 regulator-name = "vcc3v0_sd";
151 regulator-boot-on;
152 regulator-min-microvolt = <3000000>;
153 regulator-max-microvolt = <3000000>;
154 vin-supply = <&vcc3v3_sys>;
155 };
156
157 vcc3v3_sys: regulator-vcc3v3-sys {
158 compatible = "regulator-fixed";
159 regulator-name = "vcc3v3_sys";
160 regulator-always-on;
161 regulator-boot-on;
162 regulator-min-microvolt = <3300000>;
163 regulator-max-microvolt = <3300000>;
164 vin-supply = <&sys_12v>;
165 };
166
167 vcca_0v9: regulator-vcca-0v9 {
168 compatible = "regulator-fixed";
169 regulator-name = "vcca_0v9";
170 regulator-always-on;
171 regulator-boot-on;
172 regulator-min-microvolt = <900000>;
173 regulator-max-microvolt = <900000>;
174 vin-supply = <&vcc3v3_sys>;
175 };
176
177 /* Actually 3 regulators (host0, 1, 2) controlled by the same gpio */
178 vcc5v0_host: regulator-vcc5v0-host {
179 compatible = "regulator-fixed";
180 enable-active-high;
181 gpio = <&gpio1 RK_PA0 GPIO_ACTIVE_HIGH>;
182 pinctrl-names = "default";
183 pinctrl-0 = <&vcc5v0_host_en &hub_rst>;
184 regulator-name = "vcc5v0_host";
185 vin-supply = <&vcc_sys>;
186 };
187
188 vcc_vbus_typec1: regulator-vcc-vbus-typec1 {
189 compatible = "regulator-fixed";
190 enable-active-high;
191 gpio = <&gpio1 RK_PB5 GPIO_ACTIVE_HIGH>;
192 pinctrl-names = "default";
193 pinctrl-0 = <&vcc_vbus_typec1_en>;
194 regulator-name = "vcc_vbus_typec1";
195 regulator-always-on;
196 vin-supply = <&vcc_sys>;
197 };
198
199 vcc_sys: regulator-vcc-sys {
200 compatible = "regulator-fixed";
201 enable-active-high;
202 gpio = <&gpio2 RK_PA6 GPIO_ACTIVE_HIGH>;
203 pinctrl-names = "default";
204 pinctrl-0 = <&vcc_sys_en>;
205 regulator-name = "vcc_sys";
206 regulator-boot-on;
207 regulator-min-microvolt = <5000000>;
208 regulator-max-microvolt = <5000000>;
209 vin-supply = <&sys_12v>;
210 };
211
212 vdd_log: regulator-vdd-log {
213 compatible = "pwm-regulator";
214 pwms = <&pwm2 0 25000 1>;
215 regulator-name = "vdd_log";
216 regulator-always-on;
217 regulator-boot-on;
218 regulator-min-microvolt = <450000>;
219 regulator-max-microvolt = <1400000>;
220 pwm-supply = <&vcc3v3_sys>;
221 };
222 };
223
224 &cpu_l0 {
225 cpu-supply = <&vdd_cpu_l>;
226 };
227
228 &cpu_l1 {
229 cpu-supply = <&vdd_cpu_l>;
230 };
231
232 &cpu_l2 {
233 cpu-supply = <&vdd_cpu_l>;
234 };
235
236 &cpu_l3 {
237 cpu-supply = <&vdd_cpu_l>;
238 };
239
240 &cpu_b0 {
241 cpu-supply = <&vdd_cpu_b>;
242 };
243
244 &cpu_b1 {
245 cpu-supply = <&vdd_cpu_b>;
246 };
247
248 &emmc_phy {
249 status = "okay";
250 };
251
252 &gmac {
253 assigned-clocks = <&cru SCLK_RMII_SRC>;
254 assigned-clock-parents = <&clkin_gmac>;
255 clock_in_out = "input";
256 phy-supply = <&vcc_lan>;
257 phy-mode = "rgmii";
258 pinctrl-names = "default";
259 pinctrl-0 = <&rgmii_pins>;
260 snps,reset-gpio = <&gpio3 RK_PB7 GPIO_ACTIVE_LOW>;
261 snps,reset-active-low;
262 snps,reset-delays-us = <0 10000 50000>;
263 tx_delay = <0x28>;
264 rx_delay = <0x11>;
265 status = "okay";
266 };
267
268 &gpu {
269 mali-supply = <&vdd_gpu>;
270 status = "okay";
271 };
272
273 &hdmi {
274 avdd-0v9-supply = <&vcca0v9_hdmi>;
275 avdd-1v8-supply = <&vcca1v8_hdmi>;
276 ddc-i2c-bus = <&i2c3>;
277 pinctrl-names = "default";
278 pinctrl-0 = <&hdmi_cec>;
279 status = "okay";
280 };
281
282 &hdmi_sound {
283 status = "okay";
284 };
285
286 &i2c0 {
287 clock-frequency = <400000>;
288 i2c-scl-rising-time-ns = <168>;
289 i2c-scl-falling-time-ns = <4>;
290 status = "okay";
291
292 rk808: pmic@1b {
293 compatible = "rockchip,rk808";
294 reg = <0x1b>;
295 interrupt-parent = <&gpio1>;
296 interrupts = <21 IRQ_TYPE_LEVEL_LOW>;
297 #clock-cells = <1>;
298 clock-output-names = "xin32k", "rk808-clkout2";
299 pinctrl-names = "default";
300 pinctrl-0 = <&pmic_int_l>;
301 system-power-controller;
302 wakeup-source;
303
304 vcc1-supply = <&vcc3v3_sys>;
305 vcc2-supply = <&vcc3v3_sys>;
306 vcc3-supply = <&vcc3v3_sys>;
307 vcc4-supply = <&vcc3v3_sys>;
308 vcc6-supply = <&vcc3v3_sys>;
309 vcc7-supply = <&vcc3v3_sys>;
310 vcc8-supply = <&vcc3v3_sys>;
311 vcc9-supply = <&vcc3v3_sys>;
312 vcc10-supply = <&vcc3v3_sys>;
313 vcc11-supply = <&vcc3v3_sys>;
314 vcc12-supply = <&vcc3v3_sys>;
315 vddio-supply = <&vcc_3v0>;
316
317 regulators {
318 vdd_center: DCDC_REG1 {
319 regulator-name = "vdd_center";
320 regulator-always-on;
321 regulator-boot-on;
322 regulator-min-microvolt = <750000>;
323 regulator-max-microvolt = <1350000>;
324 regulator-ramp-delay = <6001>;
325 regulator-state-mem {
326 regulator-off-in-suspend;
327 };
328 };
329
330 vdd_cpu_l: DCDC_REG2 {
331 regulator-name = "vdd_cpu_l";
332 regulator-always-on;
333 regulator-boot-on;
334 regulator-min-microvolt = <750000>;
335 regulator-max-microvolt = <1350000>;
336 regulator-ramp-delay = <6001>;
337 regulator-state-mem {
338 regulator-off-in-suspend;
339 };
340 };
341
342 vcc_ddr: DCDC_REG3 {
343 regulator-name = "vcc_ddr";
344 regulator-always-on;
345 regulator-boot-on;
346 regulator-state-mem {
347 regulator-on-in-suspend;
348 };
349 };
350
351 vcc_1v8: DCDC_REG4 {
352 regulator-name = "vcc_1v8";
353 regulator-always-on;
354 regulator-boot-on;
355 regulator-min-microvolt = <1800000>;
356 regulator-max-microvolt = <1800000>;
357 regulator-state-mem {
358 regulator-on-in-suspend;
359 regulator-suspend-microvolt = <1800000>;
360 };
361 };
362
363 vcca1v8_codec: LDO_REG1 {
364 regulator-name = "vcca1v8_codec";
365 regulator-always-on;
366 regulator-boot-on;
367 regulator-min-microvolt = <1800000>;
368 regulator-max-microvolt = <1800000>;
369 regulator-state-mem {
370 regulator-off-in-suspend;
371 };
372 };
373
374 vcca1v8_hdmi: LDO_REG2 {
375 regulator-name = "vcca1v8_hdmi";
376 regulator-always-on;
377 regulator-boot-on;
378 regulator-min-microvolt = <1800000>;
379 regulator-max-microvolt = <1800000>;
380 regulator-state-mem {
381 regulator-off-in-suspend;
382 };
383 };
384
385 vcc1v8_pmu: LDO_REG3 {
386 regulator-name = "vcc1v8_pmu";
387 regulator-always-on;
388 regulator-boot-on;
389 regulator-min-microvolt = <1800000>;
390 regulator-max-microvolt = <1800000>;
391 regulator-state-mem {
392 regulator-on-in-suspend;
393 regulator-suspend-microvolt = <1800000>;
394 };
395 };
396
397 vcc_sdio: LDO_REG4 {
398 regulator-name = "vcc_sdio";
399 regulator-always-on;
400 regulator-boot-on;
401 regulator-min-microvolt = <1800000>;
402 regulator-max-microvolt = <3000000>;
403 regulator-state-mem {
404 regulator-on-in-suspend;
405 regulator-suspend-microvolt = <3000000>;
406 };
407 };
408
409 vcca3v0_codec: LDO_REG5 {
410 regulator-name = "vcca3v0_codec";
411 regulator-boot-on;
412 regulator-min-microvolt = <3000000>;
413 regulator-max-microvolt = <3000000>;
414 regulator-state-mem {
415 regulator-off-in-suspend;
416 };
417 };
418
419 vcc_1v5: LDO_REG6 {
420 regulator-name = "vcc_1v5";
421 regulator-always-on;
422 regulator-boot-on;
423 regulator-min-microvolt = <1500000>;
424 regulator-max-microvolt = <1500000>;
425 regulator-state-mem {
426 regulator-on-in-suspend;
427 regulator-suspend-microvolt = <1500000>;
428 };
429 };
430
431 vcca0v9_hdmi: LDO_REG7 {
432 regulator-name = "vcca0v9_hdmi";
433 regulator-always-on;
434 regulator-boot-on;
435 regulator-min-microvolt = <900000>;
436 regulator-max-microvolt = <900000>;
437 regulator-state-mem {
438 regulator-off-in-suspend;
439 };
440 };
441
442 vcc_3v0: LDO_REG8 {
443 regulator-name = "vcc_3v0";
444 regulator-always-on;
445 regulator-boot-on;
446 regulator-min-microvolt = <3000000>;
447 regulator-max-microvolt = <3000000>;
448 regulator-state-mem {
449 regulator-on-in-suspend;
450 regulator-suspend-microvolt = <3000000>;
451 };
452 };
453
454 vcc3v3_s3: vcc_lan: SWITCH_REG1 {
455 regulator-name = "vcc3v3_s3";
456 regulator-always-on;
457 regulator-boot-on;
458 regulator-state-mem {
459 regulator-off-in-suspend;
460 };
461 };
462
463 vcc3v3_s0: SWITCH_REG2 {
464 regulator-name = "vcc3v3_s0";
465 regulator-always-on;
466 regulator-boot-on;
467 regulator-state-mem {
468 regulator-off-in-suspend;
469 };
470 };
471 };
472 };
473
474 vdd_cpu_b: regulator@40 {
475 compatible = "silergy,syr827";
476 reg = <0x40>;
477 fcs,suspend-voltage-selector = <1>;
478 pinctrl-names = "default";
479 pinctrl-0 = <&vsel1_pin>;
480 regulator-name = "vdd_cpu_b";
481 regulator-min-microvolt = <712500>;
482 regulator-max-microvolt = <1500000>;
483 regulator-ramp-delay = <1000>;
484 regulator-always-on;
485 regulator-boot-on;
486 vin-supply = <&vcc3v3_sys>;
487
488 regulator-state-mem {
489 regulator-off-in-suspend;
490 };
491 };
492
493 vdd_gpu: regulator@41 {
494 compatible = "silergy,syr828";
495 reg = <0x41>;
496 fcs,suspend-voltage-selector = <1>;
497 pinctrl-names = "default";
498 pinctrl-0 = <&vsel2_pin>;
499 regulator-name = "vdd_gpu";
500 regulator-min-microvolt = <712500>;
501 regulator-max-microvolt = <1500000>;
502 regulator-ramp-delay = <1000>;
503 regulator-always-on;
504 regulator-boot-on;
505 vin-supply = <&vcc3v3_sys>;
506
507 regulator-state-mem {
508 regulator-off-in-suspend;
509 };
510 };
511 };
512
513 &i2c1 {
514 i2c-scl-rising-time-ns = <300>;
515 i2c-scl-falling-time-ns = <15>;
516 status = "okay";
517 };
518
519 &i2c3 {
520 i2c-scl-rising-time-ns = <450>;
521 i2c-scl-falling-time-ns = <15>;
522 status = "okay";
523 };
524
525 &i2c4 {
526 i2c-scl-rising-time-ns = <600>;
527 i2c-scl-falling-time-ns = <20>;
528 status = "okay";
529
530 fusb1: usb-typec@22 {
531 compatible = "fcs,fusb302";
532 reg = <0x22>;
533 interrupt-parent = <&gpio1>;
534 interrupts = <1 IRQ_TYPE_LEVEL_LOW>;
535 pinctrl-names = "default";
536 pinctrl-0 = <&fusb1_int>;
537 vbus-supply = <&vcc_vbus_typec1>;
538 status = "okay";
539 };
540 };
541
542 &i2c7 {
543 i2c-scl-rising-time-ns = <600>;
544 i2c-scl-falling-time-ns = <20>;
545 status = "okay";
546
547 fusb0: usb-typec@22 {
548 compatible = "fcs,fusb302";
549 reg = <0x22>;
550 interrupt-parent = <&gpio1>;
551 interrupts = <2 IRQ_TYPE_LEVEL_LOW>;
552 pinctrl-names = "default";
553 pinctrl-0 = <&fusb0_int>;
554 vbus-supply = <&vcc_vbus_typec0>;
555 status = "okay";
556 };
557
558 mp8859: regulator@66 {
559 compatible = "mps,mp8859";
560 reg = <0x66>;
561 dc_12v: mp8859_dcdc {
562 regulator-name = "dc_12v";
563 regulator-min-microvolt = <12000000>;
564 regulator-max-microvolt = <12000000>;
565 regulator-always-on;
566 regulator-boot-on;
567 vin-supply = <&vcc_vbus_typec0>;
568
569 regulator-state-mem {
570 regulator-on-in-suspend;
571 regulator-suspend-microvolt = <12000000>;
572 };
573 };
574 };
575 };
576
577 &i2s0 {
578 rockchip,playback-channels = <8>;
579 rockchip,capture-channels = <8>;
580 status = "okay";
581 };
582
583 &i2s1 {
584 rockchip,playback-channels = <2>;
585 rockchip,capture-channels = <2>;
586 status = "okay";
587 };
588
589 &i2s2 {
590 status = "okay";
591 };
592
593 &io_domains {
594 audio-supply = <&vcca1v8_codec>;
595 bt656-supply = <&vcc_3v0>;
596 gpio1830-supply = <&vcc_3v0>;
597 sdmmc-supply = <&vcc_sdio>;
598 status = "okay";
599 };
600
601 &pmu_io_domains {
602 pmu1830-supply = <&vcc_3v0>;
603 status = "okay";
604 };
605
606 &pinctrl {
607 buttons {
608 pwr_key_l: pwr-key-l {
609 rockchip,pins = <0 RK_PA5 RK_FUNC_GPIO &pcfg_pull_up>;
610 };
611 };
612
613 ir {
614 ir_int: ir-int {
615 rockchip,pins = <0 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
616 };
617 };
618
619 lcd-panel {
620 lcd_panel_reset: lcd-panel-reset {
621 rockchip,pins = <4 RK_PD5 RK_FUNC_GPIO &pcfg_pull_up>;
622 };
623 };
624
625 leds {
626 diy_led_pin: diy-led-pin {
627 rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
628 };
629
630 work_led_pin: work-led-pin {
631 rockchip,pins = <2 RK_PD3 RK_FUNC_GPIO &pcfg_pull_none>;
632 };
633
634 yellow_led_pin: yellow-led-pin {
635 rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_none>;
636 };
637 };
638
639 pmic {
640 vsel1_pin: vsel1-pin {
641 rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
642 };
643
644 vsel2_pin: vsel2-pin {
645 rockchip,pins = <1 RK_PB6 RK_FUNC_GPIO &pcfg_pull_down>;
646 };
647 };
648
649 sdio-pwrseq {
650 wifi_enable_h: wifi-enable-h {
651 rockchip,pins = <0 RK_PB2 RK_FUNC_GPIO &pcfg_pull_none>;
652 };
653 };
654
655 sdmmc {
656 vcc3v0_sd_en: vcc3v0-sd-en {
657 rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>;
658 };
659 };
660
661 pmic {
662 pmic_int_l: pmic-int-l {
663 rockchip,pins = <1 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
664 };
665 };
666
667 usb2 {
668 vcc5v0_host_en: vcc5v0-host-en {
669 rockchip,pins = <1 RK_PA0 RK_FUNC_GPIO &pcfg_pull_none>;
670 };
671
672 vcc_sys_en: vcc-sys-en {
673 rockchip,pins = <2 RK_PA6 RK_FUNC_GPIO &pcfg_pull_none>;
674 };
675
676 hub_rst: hub-rst {
677 rockchip,pins = <2 RK_PA4 RK_FUNC_GPIO &pcfg_output_high>;
678 };
679 };
680
681 usb-typec {
682 vcc_vbus_typec1_en: vcc-vbus-typec1-en {
683 rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
684 };
685 };
686
687 fusb30x {
688 fusb0_int: fusb0-int {
689 rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>;
690 };
691
692 fusb1_int: fusb1-int {
693 rockchip,pins = <1 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>;
694 };
695 };
696 };
697
698 &pwm0 {
699 status = "okay";
700 };
701
702 &pwm2 {
703 status = "okay";
704 };
705
706 &saradc {
707 vref-supply = <&vcca1v8_s3>;
708 status = "okay";
709 };
710
711 &sdmmc {
712 bus-width = <4>;
713 cap-sd-highspeed;
714 cd-gpios = <&gpio0 RK_PA7 GPIO_ACTIVE_LOW>;
715 disable-wp;
716 max-frequency = <150000000>;
717 pinctrl-names = "default";
718 pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_bus4>;
719 sd-uhs-sdr104;
720 vmmc-supply = <&vcc3v0_sd>;
721 vqmmc-supply = <&vcc_sdio>;
722 status = "okay";
723 };
724
725 &sdhci {
726 bus-width = <8>;
727 non-removable;
728 status = "okay";
729 };
730
731 &spi1 {
732 status = "okay";
733
734 flash@0 {
735 compatible = "jedec,spi-nor";
736 reg = <0>;
737 spi-max-frequency = <30000000>;
738 vcc-supply = <&vcc3v3_sys>;
739 };
740 };
741
742 &tcphy0 {
743 status = "okay";
744 };
745
746 &tcphy1 {
747 status = "okay";
748 };
749
750 &tsadc {
751 /* tshut mode 0:CRU 1:GPIO */
752 rockchip,hw-tshut-mode = <1>;
753 /* tshut polarity 0:LOW 1:HIGH */
754 rockchip,hw-tshut-polarity = <1>;
755 status = "okay";
756 };
757
758 &u2phy0 {
759 status = "okay";
760
761 u2phy0_otg: otg-port {
762 phy-supply = <&vcc_vbus_typec0>;
763 status = "okay";
764 };
765
766 u2phy0_host: host-port {
767 phy-supply = <&vcc5v0_host>;
768 status = "okay";
769 };
770 };
771
772 &u2phy1 {
773 status = "okay";
774
775 u2phy1_otg: otg-port {
776 phy-supply = <&vcc_vbus_typec1>;
777 status = "okay";
778 };
779
780 u2phy1_host: host-port {
781 phy-supply = <&vcc5v0_host>;
782 status = "okay";
783 };
784 };
785
786 &uart0 {
787 pinctrl-names = "default";
788 pinctrl-0 = <&uart0_xfer &uart0_cts>;
789 status = "okay";
790 };
791
792 &uart2 {
793 status = "okay";
794 };
795
796 &usb_host0_ehci {
797 status = "okay";
798 };
799
800 &usb_host0_ohci {
801 status = "okay";
802 };
803
804 &usb_host1_ehci {
805 status = "okay";
806 };
807
808 &usb_host1_ohci {
809 status = "okay";
810 };
811
812 &usbdrd3_0 {
813 status = "okay";
814 };
815
816 &usbdrd_dwc3_0 {
817 status = "okay";
818 };
819
820 &usbdrd3_1 {
821 status = "okay";
822 };
823
824 &usbdrd_dwc3_1 {
825 status = "okay";
826 dr_mode = "host";
827 };
828
829 &vopb {
830 status = "okay";
831 };
832
833 &vopb_mmu {
834 status = "okay";
835 };
836
837 &vopl {
838 status = "okay";
839 };
840
841 &vopl_mmu {
842 status = "okay";
843 };