| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Google Gru (and derivatives) board device tree source |
| 4 |
* |
| 5 |
* Copyright 2016-2017 Google, Inc |
| 6 |
*/ |
| 7 |
|
| 8 |
#include <dt-bindings/input/input.h> |
| 9 |
#include "rk3399-op1.dtsi" |
| 10 |
|
| 11 |
/ { |
| 12 |
aliases { |
| 13 |
mmc0 = &sdmmc; |
| 14 |
mmc1 = &sdhci; |
| 15 |
}; |
| 16 |
|
| 17 |
chosen { |
| 18 |
stdout-path = "serial2:115200n8"; |
| 19 |
}; |
| 20 |
|
| 21 |
/* |
| 22 |
* Power Tree |
| 23 |
* |
| 24 |
* In general an attempt is made to include all rails called out by |
| 25 |
* the schematic as long as those rails interact in some way with |
| 26 |
* the AP. AKA: |
| 27 |
* - Rails that only connect to the EC (or devices that the EC talks to) |
| 28 |
* are not included. |
| 29 |
* - Rails _are_ included if the rails go to the AP even if the AP |
| 30 |
* doesn't currently care about them / they are always on. The idea |
| 31 |
* here is that it makes it easier to map to the schematic or extend |
| 32 |
* later. |
| 33 |
* |
| 34 |
* If two rails are substantially the same from the AP's point of |
| 35 |
* view, though, we won't create a full fixed regulator. We'll just |
| 36 |
* put the child rail as an alias of the parent rail. Sometimes rails |
| 37 |
* look the same to the AP because one of these is true: |
| 38 |
* - The EC controls the enable and the EC always enables a rail as |
| 39 |
* long as the AP is running. |
| 40 |
* - The rails are actually connected to each other by a jumper and |
| 41 |
* the distinction is just there to add clarity/flexibility to the |
| 42 |
* schematic. |
| 43 |
*/ |
| 44 |
|
| 45 |
ppvar_sys: regulator-ppvar-sys { |
| 46 |
compatible = "regulator-fixed"; |
| 47 |
regulator-name = "ppvar_sys"; |
| 48 |
regulator-always-on; |
| 49 |
regulator-boot-on; |
| 50 |
}; |
| 51 |
|
| 52 |
pp1200_lpddr: regulator-pp1200-lpddr { |
| 53 |
compatible = "regulator-fixed"; |
| 54 |
regulator-name = "pp1200_lpddr"; |
| 55 |
|
| 56 |
/* EC turns on w/ lpddr_pwr_en; always on for AP */ |
| 57 |
regulator-always-on; |
| 58 |
regulator-boot-on; |
| 59 |
regulator-min-microvolt = <1200000>; |
| 60 |
regulator-max-microvolt = <1200000>; |
| 61 |
|
| 62 |
vin-supply = <&ppvar_sys>; |
| 63 |
}; |
| 64 |
|
| 65 |
pp1800: regulator-pp1800 { |
| 66 |
compatible = "regulator-fixed"; |
| 67 |
regulator-name = "pp1800"; |
| 68 |
|
| 69 |
/* Always on when ppvar_sys shows power good */ |
| 70 |
regulator-always-on; |
| 71 |
regulator-boot-on; |
| 72 |
regulator-min-microvolt = <1800000>; |
| 73 |
regulator-max-microvolt = <1800000>; |
| 74 |
|
| 75 |
vin-supply = <&ppvar_sys>; |
| 76 |
}; |
| 77 |
|
| 78 |
pp3300: regulator-pp3300 { |
| 79 |
compatible = "regulator-fixed"; |
| 80 |
regulator-name = "pp3300"; |
| 81 |
|
| 82 |
/* Always on; plain and simple */ |
| 83 |
regulator-always-on; |
| 84 |
regulator-boot-on; |
| 85 |
regulator-min-microvolt = <3300000>; |
| 86 |
regulator-max-microvolt = <3300000>; |
| 87 |
|
| 88 |
vin-supply = <&ppvar_sys>; |
| 89 |
}; |
| 90 |
|
| 91 |
pp5000: regulator-pp5000 { |
| 92 |
compatible = "regulator-fixed"; |
| 93 |
regulator-name = "pp5000"; |
| 94 |
|
| 95 |
/* EC turns on w/ pp5000_en; always on for AP */ |
| 96 |
regulator-always-on; |
| 97 |
regulator-boot-on; |
| 98 |
regulator-min-microvolt = <5000000>; |
| 99 |
regulator-max-microvolt = <5000000>; |
| 100 |
|
| 101 |
vin-supply = <&ppvar_sys>; |
| 102 |
}; |
| 103 |
|
| 104 |
ppvar_bigcpu_pwm: regulator-ppvar-bigcpu-pwm { |
| 105 |
compatible = "pwm-regulator"; |
| 106 |
regulator-name = "ppvar_bigcpu_pwm"; |
| 107 |
|
| 108 |
pwms = <&pwm1 0 3337 0>; |
| 109 |
pwm-supply = <&ppvar_sys>; |
| 110 |
pwm-dutycycle-range = <100 0>; |
| 111 |
pwm-dutycycle-unit = <100>; |
| 112 |
|
| 113 |
/* EC turns on w/ ap_core_en; always on for AP */ |
| 114 |
regulator-always-on; |
| 115 |
regulator-boot-on; |
| 116 |
regulator-min-microvolt = <800107>; |
| 117 |
regulator-max-microvolt = <1302232>; |
| 118 |
}; |
| 119 |
|
| 120 |
ppvar_bigcpu: ppvar-bigcpu { |
| 121 |
compatible = "vctrl-regulator"; |
| 122 |
regulator-name = "ppvar_bigcpu"; |
| 123 |
|
| 124 |
regulator-min-microvolt = <800107>; |
| 125 |
regulator-max-microvolt = <1302232>; |
| 126 |
|
| 127 |
ctrl-supply = <&ppvar_bigcpu_pwm>; |
| 128 |
ctrl-voltage-range = <800107 1302232>; |
| 129 |
|
| 130 |
regulator-settling-time-up-us = <322>; |
| 131 |
}; |
| 132 |
|
| 133 |
ppvar_litcpu_pwm: regulator-ppvar-litcpu-pwm { |
| 134 |
compatible = "pwm-regulator"; |
| 135 |
regulator-name = "ppvar_litcpu_pwm"; |
| 136 |
|
| 137 |
pwms = <&pwm2 0 3337 0>; |
| 138 |
pwm-supply = <&ppvar_sys>; |
| 139 |
pwm-dutycycle-range = <100 0>; |
| 140 |
pwm-dutycycle-unit = <100>; |
| 141 |
|
| 142 |
/* EC turns on w/ ap_core_en; always on for AP */ |
| 143 |
regulator-always-on; |
| 144 |
regulator-boot-on; |
| 145 |
regulator-min-microvolt = <797743>; |
| 146 |
regulator-max-microvolt = <1307837>; |
| 147 |
}; |
| 148 |
|
| 149 |
ppvar_litcpu: ppvar-litcpu { |
| 150 |
compatible = "vctrl-regulator"; |
| 151 |
regulator-name = "ppvar_litcpu"; |
| 152 |
|
| 153 |
regulator-min-microvolt = <797743>; |
| 154 |
regulator-max-microvolt = <1307837>; |
| 155 |
|
| 156 |
ctrl-supply = <&ppvar_litcpu_pwm>; |
| 157 |
ctrl-voltage-range = <797743 1307837>; |
| 158 |
|
| 159 |
regulator-settling-time-up-us = <384>; |
| 160 |
}; |
| 161 |
|
| 162 |
ppvar_gpu_pwm: regulator-ppvar-gpu-pwm { |
| 163 |
compatible = "pwm-regulator"; |
| 164 |
regulator-name = "ppvar_gpu_pwm"; |
| 165 |
|
| 166 |
pwms = <&pwm0 0 3337 0>; |
| 167 |
pwm-supply = <&ppvar_sys>; |
| 168 |
pwm-dutycycle-range = <100 0>; |
| 169 |
pwm-dutycycle-unit = <100>; |
| 170 |
|
| 171 |
/* EC turns on w/ ap_core_en; always on for AP */ |
| 172 |
regulator-always-on; |
| 173 |
regulator-boot-on; |
| 174 |
regulator-min-microvolt = <786384>; |
| 175 |
regulator-max-microvolt = <1217747>; |
| 176 |
}; |
| 177 |
|
| 178 |
ppvar_gpu: ppvar-gpu { |
| 179 |
compatible = "vctrl-regulator"; |
| 180 |
regulator-name = "ppvar_gpu"; |
| 181 |
|
| 182 |
regulator-min-microvolt = <786384>; |
| 183 |
regulator-max-microvolt = <1217747>; |
| 184 |
|
| 185 |
ctrl-supply = <&ppvar_gpu_pwm>; |
| 186 |
ctrl-voltage-range = <786384 1217747>; |
| 187 |
|
| 188 |
regulator-settling-time-up-us = <390>; |
| 189 |
}; |
| 190 |
|
| 191 |
/* EC turns on w/ pp900_ddrpll_en */ |
| 192 |
pp900_ddrpll: regulator-pp900-ap { |
| 193 |
}; |
| 194 |
|
| 195 |
/* EC turns on w/ pp900_pll_en */ |
| 196 |
pp900_pll: regulator-pp900-ap { |
| 197 |
}; |
| 198 |
|
| 199 |
/* EC turns on w/ pp900_pmu_en */ |
| 200 |
pp900_pmu: regulator-pp900-ap { |
| 201 |
}; |
| 202 |
|
| 203 |
/* EC turns on w/ pp1800_s0_en_l */ |
| 204 |
pp1800_ap_io: pp1800_emmc: pp1800_nfc: pp1800_s0: regulator-pp1800 { |
| 205 |
}; |
| 206 |
|
| 207 |
/* EC turns on w/ pp1800_avdd_en_l */ |
| 208 |
pp1800_avdd: regulator-pp1800 { |
| 209 |
}; |
| 210 |
|
| 211 |
/* EC turns on w/ pp1800_lid_en_l */ |
| 212 |
pp1800_lid: pp1800_mic: regulator-pp1800 { |
| 213 |
}; |
| 214 |
|
| 215 |
/* EC turns on w/ lpddr_pwr_en */ |
| 216 |
pp1800_lpddr: regulator-pp1800 { |
| 217 |
}; |
| 218 |
|
| 219 |
/* EC turns on w/ pp1800_pmu_en_l */ |
| 220 |
pp1800_pmu: regulator-pp1800 { |
| 221 |
}; |
| 222 |
|
| 223 |
/* EC turns on w/ pp1800_usb_en_l */ |
| 224 |
pp1800_usb: regulator-pp1800 { |
| 225 |
}; |
| 226 |
|
| 227 |
pp3000_sd_slot: regulator-pp3000-sd-slot { |
| 228 |
compatible = "regulator-fixed"; |
| 229 |
regulator-name = "pp3000_sd_slot"; |
| 230 |
pinctrl-names = "default"; |
| 231 |
pinctrl-0 = <&sd_slot_pwr_en>; |
| 232 |
|
| 233 |
enable-active-high; |
| 234 |
gpio = <&gpio4 29 GPIO_ACTIVE_HIGH>; |
| 235 |
|
| 236 |
vin-supply = <&pp3000>; |
| 237 |
}; |
| 238 |
|
| 239 |
/* |
| 240 |
* Technically, this is a small abuse of 'regulator-gpio'; this |
| 241 |
* regulator is a mux between pp1800 and pp3300. pp1800 and pp3300 are |
| 242 |
* always on though, so it is sufficient to simply control the mux |
| 243 |
* here. |
| 244 |
*/ |
| 245 |
ppvar_sd_card_io: ppvar-sd-card-io { |
| 246 |
compatible = "regulator-gpio"; |
| 247 |
regulator-name = "ppvar_sd_card_io"; |
| 248 |
pinctrl-names = "default"; |
| 249 |
pinctrl-0 = <&sd_io_pwr_en &sd_pwr_1800_sel>; |
| 250 |
|
| 251 |
enable-active-high; |
| 252 |
enable-gpios = <&gpio2 2 GPIO_ACTIVE_HIGH>; |
| 253 |
gpios = <&gpio2 28 GPIO_ACTIVE_HIGH>; |
| 254 |
states = <1800000 0x1>, |
| 255 |
<3000000 0x0>; |
| 256 |
|
| 257 |
regulator-min-microvolt = <1800000>; |
| 258 |
regulator-max-microvolt = <3000000>; |
| 259 |
}; |
| 260 |
|
| 261 |
/* EC turns on w/ pp3300_trackpad_en_l */ |
| 262 |
pp3300_trackpad: regulator-pp3300-trackpad { |
| 263 |
}; |
| 264 |
|
| 265 |
/* EC turns on w/ usb_a_en */ |
| 266 |
pp5000_usb_a_vbus: regulator-pp5000 { |
| 267 |
}; |
| 268 |
|
| 269 |
ap_rtc_clk: ap-rtc-clk { |
| 270 |
compatible = "fixed-clock"; |
| 271 |
clock-frequency = <32768>; |
| 272 |
clock-output-names = "xin32k"; |
| 273 |
#clock-cells = <0>; |
| 274 |
}; |
| 275 |
|
| 276 |
max98357a: max98357a { |
| 277 |
compatible = "maxim,max98357a"; |
| 278 |
pinctrl-names = "default"; |
| 279 |
pinctrl-0 = <&sdmode_en>; |
| 280 |
sdmode-gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>; |
| 281 |
sdmode-delay = <2>; |
| 282 |
#sound-dai-cells = <0>; |
| 283 |
status = "okay"; |
| 284 |
}; |
| 285 |
|
| 286 |
sound: sound { |
| 287 |
compatible = "rockchip,rk3399-gru-sound"; |
| 288 |
rockchip,cpu = <&i2s0 &spdif>; |
| 289 |
}; |
| 290 |
}; |
| 291 |
|
| 292 |
&cdn_dp { |
| 293 |
status = "okay"; |
| 294 |
}; |
| 295 |
|
| 296 |
/* |
| 297 |
* Set some suspend operating points to avoid OVP in suspend |
| 298 |
* |
| 299 |
* When we go into S3 ARM Trusted Firmware will transition our PWM regulators |
| 300 |
* from wherever they're at back to the "default" operating point (whatever |
| 301 |
* voltage we get when we set the PWM pins to "input"). |
| 302 |
* |
| 303 |
* This quick transition under light load has the possibility to trigger the |
| 304 |
* regulator "over voltage protection" (OVP). |
| 305 |
* |
| 306 |
* To make extra certain that we don't hit this OVP at suspend time, we'll |
| 307 |
* transition to a voltage that's much closer to the default (~1.0 V) so that |
| 308 |
* there will not be a big jump. Technically we only need to get within 200 mV |
| 309 |
* of the default voltage, but the speed here should be fast enough and we need |
| 310 |
* suspend/resume to be rock solid. |
| 311 |
*/ |
| 312 |
|
| 313 |
&cluster0_opp { |
| 314 |
opp05 { |
| 315 |
opp-suspend; |
| 316 |
}; |
| 317 |
}; |
| 318 |
|
| 319 |
&cluster1_opp { |
| 320 |
opp06 { |
| 321 |
opp-suspend; |
| 322 |
}; |
| 323 |
}; |
| 324 |
|
| 325 |
&cpu_l0 { |
| 326 |
cpu-supply = <&ppvar_litcpu>; |
| 327 |
}; |
| 328 |
|
| 329 |
&cpu_l1 { |
| 330 |
cpu-supply = <&ppvar_litcpu>; |
| 331 |
}; |
| 332 |
|
| 333 |
&cpu_l2 { |
| 334 |
cpu-supply = <&ppvar_litcpu>; |
| 335 |
}; |
| 336 |
|
| 337 |
&cpu_l3 { |
| 338 |
cpu-supply = <&ppvar_litcpu>; |
| 339 |
}; |
| 340 |
|
| 341 |
&cpu_b0 { |
| 342 |
cpu-supply = <&ppvar_bigcpu>; |
| 343 |
}; |
| 344 |
|
| 345 |
&cpu_b1 { |
| 346 |
cpu-supply = <&ppvar_bigcpu>; |
| 347 |
}; |
| 348 |
|
| 349 |
|
| 350 |
&cru { |
| 351 |
assigned-clocks = |
| 352 |
<&cru PLL_GPLL>, <&cru PLL_CPLL>, |
| 353 |
<&cru PLL_NPLL>, |
| 354 |
<&cru ACLK_PERIHP>, <&cru HCLK_PERIHP>, |
| 355 |
<&cru PCLK_PERIHP>, |
| 356 |
<&cru ACLK_PERILP0>, <&cru HCLK_PERILP0>, |
| 357 |
<&cru PCLK_PERILP0>, <&cru ACLK_CCI>, |
| 358 |
<&cru HCLK_PERILP1>, <&cru PCLK_PERILP1>, |
| 359 |
<&cru ACLK_VIO>, <&cru ACLK_HDCP>, |
| 360 |
<&cru ACLK_GIC_PRE>, |
| 361 |
<&cru PCLK_DDR>; |
| 362 |
assigned-clock-rates = |
| 363 |
<600000000>, <800000000>, |
| 364 |
<1000000000>, |
| 365 |
<150000000>, <75000000>, |
| 366 |
<37500000>, |
| 367 |
<100000000>, <100000000>, |
| 368 |
<50000000>, <800000000>, |
| 369 |
<100000000>, <50000000>, |
| 370 |
<400000000>, <400000000>, |
| 371 |
<200000000>, |
| 372 |
<200000000>; |
| 373 |
}; |
| 374 |
|
| 375 |
&dfi { |
| 376 |
status = "okay"; |
| 377 |
}; |
| 378 |
|
| 379 |
&dmc { |
| 380 |
status = "okay"; |
| 381 |
|
| 382 |
rockchip,pd-idle-ns = <160>; |
| 383 |
rockchip,sr-idle-ns = <10240>; |
| 384 |
rockchip,sr-mc-gate-idle-ns = <40960>; |
| 385 |
rockchip,srpd-lite-idle-ns = <61440>; |
| 386 |
rockchip,standby-idle-ns = <81920>; |
| 387 |
|
| 388 |
rockchip,ddr3_odt_dis_freq = <666000000>; |
| 389 |
rockchip,lpddr3_odt_dis_freq = <666000000>; |
| 390 |
rockchip,lpddr4_odt_dis_freq = <666000000>; |
| 391 |
|
| 392 |
rockchip,sr-mc-gate-idle-dis-freq-hz = <1000000000>; |
| 393 |
rockchip,srpd-lite-idle-dis-freq-hz = <0>; |
| 394 |
rockchip,standby-idle-dis-freq-hz = <928000000>; |
| 395 |
}; |
| 396 |
|
| 397 |
&dmc_opp_table { |
| 398 |
opp03 { |
| 399 |
opp-suspend; |
| 400 |
}; |
| 401 |
}; |
| 402 |
|
| 403 |
&emmc_phy { |
| 404 |
status = "okay"; |
| 405 |
}; |
| 406 |
|
| 407 |
&gpu { |
| 408 |
mali-supply = <&ppvar_gpu>; |
| 409 |
status = "okay"; |
| 410 |
}; |
| 411 |
|
| 412 |
ap_i2c_ts: &i2c3 { |
| 413 |
status = "okay"; |
| 414 |
|
| 415 |
clock-frequency = <400000>; |
| 416 |
|
| 417 |
/* These are relatively safe rise/fall times */ |
| 418 |
i2c-scl-falling-time-ns = <50>; |
| 419 |
i2c-scl-rising-time-ns = <300>; |
| 420 |
}; |
| 421 |
|
| 422 |
ap_i2c_audio: &i2c8 { |
| 423 |
status = "okay"; |
| 424 |
|
| 425 |
clock-frequency = <400000>; |
| 426 |
|
| 427 |
/* These are relatively safe rise/fall times */ |
| 428 |
i2c-scl-falling-time-ns = <50>; |
| 429 |
i2c-scl-rising-time-ns = <300>; |
| 430 |
|
| 431 |
codec: da7219@1a { |
| 432 |
compatible = "dlg,da7219"; |
| 433 |
reg = <0x1a>; |
| 434 |
interrupt-parent = <&gpio1>; |
| 435 |
interrupts = <23 IRQ_TYPE_LEVEL_LOW>; |
| 436 |
clocks = <&cru SCLK_I2S_8CH_OUT>; |
| 437 |
clock-names = "mclk"; |
| 438 |
dlg,micbias-lvl = <2600>; |
| 439 |
dlg,mic-amp-in-sel = "diff"; |
| 440 |
pinctrl-names = "default"; |
| 441 |
pinctrl-0 = <&headset_int_l>; |
| 442 |
VDD-supply = <&pp1800>; |
| 443 |
VDDMIC-supply = <&pp3300>; |
| 444 |
VDDIO-supply = <&pp1800>; |
| 445 |
|
| 446 |
da7219_aad { |
| 447 |
dlg,adc-1bit-rpt = <1>; |
| 448 |
dlg,btn-avg = <4>; |
| 449 |
dlg,btn-cfg = <50>; |
| 450 |
dlg,mic-det-thr = <500>; |
| 451 |
dlg,jack-ins-deb = <20>; |
| 452 |
dlg,jack-det-rate = "32_64"; |
| 453 |
dlg,jack-rem-deb = <1>; |
| 454 |
|
| 455 |
dlg,a-d-btn-thr = <0xa>; |
| 456 |
dlg,d-b-btn-thr = <0x16>; |
| 457 |
dlg,b-c-btn-thr = <0x21>; |
| 458 |
dlg,c-mic-btn-thr = <0x3E>; |
| 459 |
}; |
| 460 |
}; |
| 461 |
}; |
| 462 |
|
| 463 |
&i2s0 { |
| 464 |
status = "okay"; |
| 465 |
}; |
| 466 |
|
| 467 |
&io_domains { |
| 468 |
status = "okay"; |
| 469 |
|
| 470 |
audio-supply = <&pp1800_audio>; /* APIO5_VDD; 3d 4a */ |
| 471 |
bt656-supply = <&pp1800_ap_io>; /* APIO2_VDD; 2a 2b */ |
| 472 |
gpio1830-supply = <&pp3000_ap>; /* APIO4_VDD; 4c 4d */ |
| 473 |
sdmmc-supply = <&ppvar_sd_card_io>; /* SDMMC0_VDD; 4b */ |
| 474 |
}; |
| 475 |
|
| 476 |
&pcie0 { |
| 477 |
status = "okay"; |
| 478 |
|
| 479 |
ep-gpios = <&gpio2 27 GPIO_ACTIVE_HIGH>; |
| 480 |
pinctrl-names = "default"; |
| 481 |
pinctrl-0 = <&pcie_clkreqn_cpm>, <&wifi_perst_l>; |
| 482 |
vpcie3v3-supply = <&pp3300_wifi_bt>; |
| 483 |
vpcie1v8-supply = <&wlan_pd_n>; /* HACK: see &wlan_pd_n */ |
| 484 |
vpcie0v9-supply = <&pp900_pcie>; |
| 485 |
|
| 486 |
pci_rootport: pcie@0,0 { |
| 487 |
reg = <0x0000 0 0 0 0>; |
| 488 |
#address-cells = <3>; |
| 489 |
#size-cells = <2>; |
| 490 |
ranges; |
| 491 |
device_type = "pci"; |
| 492 |
}; |
| 493 |
}; |
| 494 |
|
| 495 |
&pcie_phy { |
| 496 |
status = "okay"; |
| 497 |
}; |
| 498 |
|
| 499 |
&pmu_io_domains { |
| 500 |
status = "okay"; |
| 501 |
|
| 502 |
pmu1830-supply = <&pp1800_pmu>; /* PMUIO2_VDD */ |
| 503 |
}; |
| 504 |
|
| 505 |
&pwm0 { |
| 506 |
status = "okay"; |
| 507 |
}; |
| 508 |
|
| 509 |
&pwm1 { |
| 510 |
status = "okay"; |
| 511 |
}; |
| 512 |
|
| 513 |
&pwm2 { |
| 514 |
status = "okay"; |
| 515 |
}; |
| 516 |
|
| 517 |
&pwm3 { |
| 518 |
status = "okay"; |
| 519 |
}; |
| 520 |
|
| 521 |
&sdhci { |
| 522 |
/* |
| 523 |
* Signal integrity isn't great at 200 MHz and 150 MHz (DDR) gives the |
| 524 |
* same (or nearly the same) performance for all eMMC that are intended |
| 525 |
* to be used. |
| 526 |
*/ |
| 527 |
assigned-clock-rates = <150000000>; |
| 528 |
|
| 529 |
bus-width = <8>; |
| 530 |
mmc-hs400-1_8v; |
| 531 |
mmc-hs400-enhanced-strobe; |
| 532 |
non-removable; |
| 533 |
status = "okay"; |
| 534 |
}; |
| 535 |
|
| 536 |
&sdmmc { |
| 537 |
status = "okay"; |
| 538 |
|
| 539 |
/* |
| 540 |
* Note: configure "sdmmc_cd" as card detect even though it's actually |
| 541 |
* hooked to ground. Because we specified "cd-gpios" below dw_mmc |
| 542 |
* should be ignoring card detect anyway. Specifying the pin as |
| 543 |
* sdmmc_cd means that even if you've got GRF_SOC_CON7[12] (force_jtag) |
| 544 |
* turned on that the system will still make sure the port is |
| 545 |
* configured as SDMMC and not JTAG. |
| 546 |
*/ |
| 547 |
pinctrl-names = "default"; |
| 548 |
pinctrl-0 = <&sdmmc_clk &sdmmc_cmd &sdmmc_cd &sdmmc_cd_pin |
| 549 |
&sdmmc_bus4>; |
| 550 |
|
| 551 |
bus-width = <4>; |
| 552 |
cap-mmc-highspeed; |
| 553 |
cap-sd-highspeed; |
| 554 |
cd-gpios = <&gpio4 24 GPIO_ACTIVE_LOW>; |
| 555 |
disable-wp; |
| 556 |
sd-uhs-sdr12; |
| 557 |
sd-uhs-sdr25; |
| 558 |
sd-uhs-sdr50; |
| 559 |
sd-uhs-sdr104; |
| 560 |
vmmc-supply = <&pp3000_sd_slot>; |
| 561 |
vqmmc-supply = <&ppvar_sd_card_io>; |
| 562 |
}; |
| 563 |
|
| 564 |
&spdif { |
| 565 |
status = "okay"; |
| 566 |
|
| 567 |
/* |
| 568 |
* SPDIF is routed internally to DP; we either don't use these pins, or |
| 569 |
* mux them to something else. |
| 570 |
*/ |
| 571 |
/delete-property/ pinctrl-0; |
| 572 |
/delete-property/ pinctrl-names; |
| 573 |
}; |
| 574 |
|
| 575 |
&spi1 { |
| 576 |
status = "okay"; |
| 577 |
|
| 578 |
pinctrl-names = "default", "sleep"; |
| 579 |
pinctrl-1 = <&spi1_sleep>; |
| 580 |
|
| 581 |
flash@0 { |
| 582 |
compatible = "jedec,spi-nor"; |
| 583 |
reg = <0>; |
| 584 |
|
| 585 |
/* May run faster once verified. */ |
| 586 |
spi-max-frequency = <10000000>; |
| 587 |
}; |
| 588 |
}; |
| 589 |
|
| 590 |
&spi2 { |
| 591 |
status = "okay"; |
| 592 |
}; |
| 593 |
|
| 594 |
&spi5 { |
| 595 |
status = "okay"; |
| 596 |
|
| 597 |
cros_ec: ec@0 { |
| 598 |
compatible = "google,cros-ec-spi"; |
| 599 |
reg = <0>; |
| 600 |
interrupt-parent = <&gpio0>; |
| 601 |
interrupts = <1 IRQ_TYPE_LEVEL_LOW>; |
| 602 |
pinctrl-names = "default"; |
| 603 |
pinctrl-0 = <&ec_ap_int_l>; |
| 604 |
spi-max-frequency = <3000000>; |
| 605 |
|
| 606 |
i2c_tunnel: i2c-tunnel { |
| 607 |
compatible = "google,cros-ec-i2c-tunnel"; |
| 608 |
google,remote-bus = <4>; |
| 609 |
#address-cells = <1>; |
| 610 |
#size-cells = <0>; |
| 611 |
}; |
| 612 |
|
| 613 |
usbc_extcon0: extcon0 { |
| 614 |
compatible = "google,extcon-usbc-cros-ec"; |
| 615 |
google,usb-port-id = <0>; |
| 616 |
}; |
| 617 |
}; |
| 618 |
}; |
| 619 |
|
| 620 |
&tsadc { |
| 621 |
status = "okay"; |
| 622 |
|
| 623 |
rockchip,hw-tshut-mode = <1>; /* tshut mode 0:CRU 1:GPIO */ |
| 624 |
rockchip,hw-tshut-polarity = <1>; /* tshut polarity 0:LOW 1:HIGH */ |
| 625 |
}; |
| 626 |
|
| 627 |
&tcphy0 { |
| 628 |
status = "okay"; |
| 629 |
extcon = <&usbc_extcon0>; |
| 630 |
}; |
| 631 |
|
| 632 |
&u2phy0 { |
| 633 |
status = "okay"; |
| 634 |
}; |
| 635 |
|
| 636 |
&u2phy0_host { |
| 637 |
status = "okay"; |
| 638 |
}; |
| 639 |
|
| 640 |
&u2phy1_host { |
| 641 |
status = "okay"; |
| 642 |
}; |
| 643 |
|
| 644 |
&u2phy0_otg { |
| 645 |
status = "okay"; |
| 646 |
}; |
| 647 |
|
| 648 |
&u2phy1_otg { |
| 649 |
status = "okay"; |
| 650 |
}; |
| 651 |
|
| 652 |
&uart2 { |
| 653 |
status = "okay"; |
| 654 |
}; |
| 655 |
|
| 656 |
&usb_host0_ohci { |
| 657 |
status = "okay"; |
| 658 |
}; |
| 659 |
|
| 660 |
&usbdrd3_0 { |
| 661 |
status = "okay"; |
| 662 |
extcon = <&usbc_extcon0>; |
| 663 |
}; |
| 664 |
|
| 665 |
&usbdrd_dwc3_0 { |
| 666 |
status = "okay"; |
| 667 |
dr_mode = "host"; |
| 668 |
}; |
| 669 |
|
| 670 |
&vopb { |
| 671 |
status = "okay"; |
| 672 |
}; |
| 673 |
|
| 674 |
&vopb_mmu { |
| 675 |
status = "okay"; |
| 676 |
}; |
| 677 |
|
| 678 |
&vopl { |
| 679 |
status = "okay"; |
| 680 |
}; |
| 681 |
|
| 682 |
&vopl_mmu { |
| 683 |
status = "okay"; |
| 684 |
}; |
| 685 |
|
| 686 |
#include <arm/cros-ec-keyboard.dtsi> |
| 687 |
#include <arm/cros-ec-sbs.dtsi> |
| 688 |
|
| 689 |
&pinctrl { |
| 690 |
/* |
| 691 |
* pinctrl settings for pins that have no real owners. |
| 692 |
* |
| 693 |
* At the moment settings are identical for S0 and S3, but if we later |
| 694 |
* need to configure things differently for S3 we'll adjust here. |
| 695 |
*/ |
| 696 |
pinctrl-names = "default"; |
| 697 |
pinctrl-0 = < |
| 698 |
&ap_pwroff /* AP will auto-assert this when in S3 */ |
| 699 |
&clk_32k /* This pin is always 32k on gru boards */ |
| 700 |
>; |
| 701 |
|
| 702 |
pcfg_output_low: pcfg-output-low { |
| 703 |
output-low; |
| 704 |
}; |
| 705 |
|
| 706 |
pcfg_output_high: pcfg-output-high { |
| 707 |
output-high; |
| 708 |
}; |
| 709 |
|
| 710 |
pcfg_pull_none_8ma: pcfg-pull-none-8ma { |
| 711 |
bias-disable; |
| 712 |
drive-strength = <8>; |
| 713 |
}; |
| 714 |
|
| 715 |
backlight-enable { |
| 716 |
bl_en: bl-en { |
| 717 |
rockchip,pins = <1 RK_PC1 RK_FUNC_GPIO &pcfg_pull_none>; |
| 718 |
}; |
| 719 |
}; |
| 720 |
|
| 721 |
cros-ec { |
| 722 |
ec_ap_int_l: ec-ap-int-l { |
| 723 |
rockchip,pins = <0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>; |
| 724 |
}; |
| 725 |
}; |
| 726 |
|
| 727 |
discretes { |
| 728 |
sd_io_pwr_en: sd-io-pwr-en { |
| 729 |
rockchip,pins = <2 RK_PA2 RK_FUNC_GPIO |
| 730 |
&pcfg_pull_none>; |
| 731 |
}; |
| 732 |
|
| 733 |
sd_pwr_1800_sel: sd-pwr-1800-sel { |
| 734 |
rockchip,pins = <2 RK_PD4 RK_FUNC_GPIO |
| 735 |
&pcfg_pull_none>; |
| 736 |
}; |
| 737 |
|
| 738 |
sd_slot_pwr_en: sd-slot-pwr-en { |
| 739 |
rockchip,pins = <4 RK_PD5 RK_FUNC_GPIO |
| 740 |
&pcfg_pull_none>; |
| 741 |
}; |
| 742 |
}; |
| 743 |
|
| 744 |
codec { |
| 745 |
/* Has external pullup */ |
| 746 |
headset_int_l: headset-int-l { |
| 747 |
rockchip,pins = <1 RK_PC7 RK_FUNC_GPIO &pcfg_pull_none>; |
| 748 |
}; |
| 749 |
|
| 750 |
mic_int: mic-int { |
| 751 |
rockchip,pins = <1 RK_PB5 RK_FUNC_GPIO &pcfg_pull_down>; |
| 752 |
}; |
| 753 |
}; |
| 754 |
|
| 755 |
max98357a { |
| 756 |
sdmode_en: sdmode-en { |
| 757 |
rockchip,pins = <1 RK_PA2 RK_FUNC_GPIO &pcfg_pull_down>; |
| 758 |
}; |
| 759 |
}; |
| 760 |
|
| 761 |
pcie { |
| 762 |
pcie_clkreqn_cpm: pci-clkreqn-cpm { |
| 763 |
/* |
| 764 |
* Since our pcie doesn't support ClockPM(CPM), we want |
| 765 |
* to hack this as gpio, so the EP could be able to |
| 766 |
* de-assert it along and make ClockPM(CPM) work. |
| 767 |
*/ |
| 768 |
rockchip,pins = <2 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>; |
| 769 |
}; |
| 770 |
}; |
| 771 |
|
| 772 |
sdmmc { |
| 773 |
/* |
| 774 |
* We run sdmmc at max speed; bump up drive strength. |
| 775 |
* We also have external pulls, so disable the internal ones. |
| 776 |
*/ |
| 777 |
sdmmc_bus4: sdmmc-bus4 { |
| 778 |
rockchip,pins = |
| 779 |
<4 RK_PB0 1 &pcfg_pull_none_8ma>, |
| 780 |
<4 RK_PB1 1 &pcfg_pull_none_8ma>, |
| 781 |
<4 RK_PB2 1 &pcfg_pull_none_8ma>, |
| 782 |
<4 RK_PB3 1 &pcfg_pull_none_8ma>; |
| 783 |
}; |
| 784 |
|
| 785 |
sdmmc_clk: sdmmc-clk { |
| 786 |
rockchip,pins = |
| 787 |
<4 RK_PB4 1 &pcfg_pull_none_8ma>; |
| 788 |
}; |
| 789 |
|
| 790 |
sdmmc_cmd: sdmmc-cmd { |
| 791 |
rockchip,pins = |
| 792 |
<4 RK_PB5 1 &pcfg_pull_none_8ma>; |
| 793 |
}; |
| 794 |
|
| 795 |
/* |
| 796 |
* In our case the official card detect is hooked to ground |
| 797 |
* to avoid getting access to JTAG just by sticking something |
| 798 |
* in the SD card slot (see the force_jtag bit in the TRM). |
| 799 |
* |
| 800 |
* We still configure it as card detect because it doesn't |
| 801 |
* hurt and dw_mmc will ignore it. We make sure to disable |
| 802 |
* the pull though so we don't burn needless power. |
| 803 |
*/ |
| 804 |
sdmmc_cd: sdmmc-cd { |
| 805 |
rockchip,pins = |
| 806 |
<0 RK_PA7 1 &pcfg_pull_none>; |
| 807 |
}; |
| 808 |
|
| 809 |
/* This is where we actually hook up CD; has external pull */ |
| 810 |
sdmmc_cd_pin: sdmmc-cd-pin { |
| 811 |
rockchip,pins = <4 RK_PD0 RK_FUNC_GPIO &pcfg_pull_none>; |
| 812 |
}; |
| 813 |
}; |
| 814 |
|
| 815 |
spi1 { |
| 816 |
spi1_sleep: spi1-sleep { |
| 817 |
/* |
| 818 |
* Pull down SPI1 CLK/CS/RX/TX during suspend, to |
| 819 |
* prevent leakage. |
| 820 |
*/ |
| 821 |
rockchip,pins = <1 RK_PB1 RK_FUNC_GPIO &pcfg_pull_down>, |
| 822 |
<1 RK_PB2 RK_FUNC_GPIO &pcfg_pull_down>, |
| 823 |
<1 RK_PA7 RK_FUNC_GPIO &pcfg_pull_down>, |
| 824 |
<1 RK_PB0 RK_FUNC_GPIO &pcfg_pull_down>; |
| 825 |
}; |
| 826 |
}; |
| 827 |
|
| 828 |
touchscreen { |
| 829 |
touch_int_l: touch-int-l { |
| 830 |
rockchip,pins = <3 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>; |
| 831 |
}; |
| 832 |
|
| 833 |
touch_reset_l: touch-reset-l { |
| 834 |
rockchip,pins = <4 RK_PD2 RK_FUNC_GPIO &pcfg_pull_none>; |
| 835 |
}; |
| 836 |
}; |
| 837 |
|
| 838 |
trackpad { |
| 839 |
ap_i2c_tp_pu_en: ap-i2c-tp-pu-en { |
| 840 |
rockchip,pins = <3 RK_PB4 RK_FUNC_GPIO &pcfg_output_high>; |
| 841 |
}; |
| 842 |
|
| 843 |
trackpad_int_l: trackpad-int-l { |
| 844 |
rockchip,pins = <1 RK_PA4 RK_FUNC_GPIO &pcfg_pull_up>; |
| 845 |
}; |
| 846 |
}; |
| 847 |
|
| 848 |
wifi: wifi { |
| 849 |
wlan_module_reset_l: wlan-module-reset-l { |
| 850 |
rockchip,pins = <1 RK_PB3 RK_FUNC_GPIO &pcfg_pull_none>; |
| 851 |
}; |
| 852 |
|
| 853 |
bt_host_wake_l: bt-host-wake-l { |
| 854 |
/* Kevin has an external pull up, but Gru does not */ |
| 855 |
rockchip,pins = <0 RK_PA3 RK_FUNC_GPIO &pcfg_pull_up>; |
| 856 |
}; |
| 857 |
}; |
| 858 |
|
| 859 |
write-protect { |
| 860 |
ap_fw_wp: ap-fw-wp { |
| 861 |
rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_up>; |
| 862 |
}; |
| 863 |
}; |
| 864 |
}; |