| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Google Gru-Kevin Rev 6+ board device tree source |
| 4 |
* |
| 5 |
* Copyright 2016-2017 Google, Inc |
| 6 |
*/ |
| 7 |
|
| 8 |
/dts-v1/; |
| 9 |
#include "rk3399-gru-chromebook.dtsi" |
| 10 |
#include <dt-bindings/input/linux-event-codes.h> |
| 11 |
|
| 12 |
/* |
| 13 |
* Kevin-specific things |
| 14 |
* |
| 15 |
* Things in this section should use names from Kevin schematic since no |
| 16 |
* equivalent exists in Gru schematic. If referring to signals that exist |
| 17 |
* in Gru we use the Gru names, though. Confusing enough for you? |
| 18 |
*/ |
| 19 |
/ { |
| 20 |
model = "Google Kevin"; |
| 21 |
compatible = "google,kevin-rev15", "google,kevin-rev14", |
| 22 |
"google,kevin-rev13", "google,kevin-rev12", |
| 23 |
"google,kevin-rev11", "google,kevin-rev10", |
| 24 |
"google,kevin-rev9", "google,kevin-rev8", |
| 25 |
"google,kevin-rev7", "google,kevin-rev6", |
| 26 |
"google,kevin", "google,gru", "rockchip,rk3399"; |
| 27 |
chassis-type = "convertible"; |
| 28 |
|
| 29 |
/* Power tree */ |
| 30 |
|
| 31 |
p3_3v_dig: regulator-p3-3v-dig { |
| 32 |
compatible = "regulator-fixed"; |
| 33 |
regulator-name = "p3.3v_dig"; |
| 34 |
pinctrl-names = "default"; |
| 35 |
pinctrl-0 = <&cpu3_pen_pwr_en>; |
| 36 |
|
| 37 |
enable-active-high; |
| 38 |
gpio = <&gpio4 30 GPIO_ACTIVE_HIGH>; |
| 39 |
vin-supply = <&pp3300>; |
| 40 |
}; |
| 41 |
|
| 42 |
edp_panel: edp-panel { |
| 43 |
compatible = "sharp,lq123p1jx31"; |
| 44 |
backlight = <&backlight>; |
| 45 |
power-supply = <&pp3300_disp>; |
| 46 |
|
| 47 |
panel-timing { |
| 48 |
clock-frequency = <266666667>; |
| 49 |
hactive = <2400>; |
| 50 |
hfront-porch = <48>; |
| 51 |
hback-porch = <84>; |
| 52 |
hsync-len = <32>; |
| 53 |
hsync-active = <0>; |
| 54 |
vactive = <1600>; |
| 55 |
vfront-porch = <3>; |
| 56 |
vback-porch = <120>; |
| 57 |
vsync-len = <10>; |
| 58 |
vsync-active = <0>; |
| 59 |
}; |
| 60 |
|
| 61 |
port { |
| 62 |
panel_in_edp: endpoint { |
| 63 |
remote-endpoint = <&edp_out_panel>; |
| 64 |
}; |
| 65 |
}; |
| 66 |
}; |
| 67 |
|
| 68 |
thermistor_ppvar_bigcpu: thermistor-ppvar-bigcpu { |
| 69 |
compatible = "murata,ncp15wb473"; |
| 70 |
pullup-uv = <1800000>; |
| 71 |
pullup-ohm = <25500>; |
| 72 |
pulldown-ohm = <0>; |
| 73 |
io-channels = <&saradc 2>; |
| 74 |
#thermal-sensor-cells = <0>; |
| 75 |
}; |
| 76 |
|
| 77 |
thermistor_ppvar_litcpu: thermistor-ppvar-litcpu { |
| 78 |
compatible = "murata,ncp15wb473"; |
| 79 |
pullup-uv = <1800000>; |
| 80 |
pullup-ohm = <25500>; |
| 81 |
pulldown-ohm = <0>; |
| 82 |
io-channels = <&saradc 3>; |
| 83 |
#thermal-sensor-cells = <0>; |
| 84 |
}; |
| 85 |
}; |
| 86 |
|
| 87 |
&backlight { |
| 88 |
pwms = <&cros_ec_pwm 1>; |
| 89 |
}; |
| 90 |
|
| 91 |
&gpio_keys { |
| 92 |
pinctrl-names = "default"; |
| 93 |
pinctrl-0 = <&bt_host_wake_l>, <&cpu1_pen_eject>; |
| 94 |
|
| 95 |
switch-pen-insert { |
| 96 |
label = "Pen Insert"; |
| 97 |
/* Insert = low, eject = high */ |
| 98 |
gpios = <&gpio0 13 GPIO_ACTIVE_LOW>; |
| 99 |
linux,code = <SW_PEN_INSERTED>; |
| 100 |
linux,input-type = <EV_SW>; |
| 101 |
wakeup-source; |
| 102 |
}; |
| 103 |
}; |
| 104 |
|
| 105 |
&thermal_zones { |
| 106 |
bigcpu_reg_thermal: bigcpu-reg-thermal { |
| 107 |
polling-delay-passive = <100>; /* milliseconds */ |
| 108 |
polling-delay = <1000>; /* milliseconds */ |
| 109 |
thermal-sensors = <&thermistor_ppvar_bigcpu 0>; |
| 110 |
sustainable-power = <4000>; |
| 111 |
|
| 112 |
ppvar_bigcpu_trips: trips { |
| 113 |
ppvar_bigcpu_on: ppvar-bigcpu-on { |
| 114 |
temperature = <40000>; /* millicelsius */ |
| 115 |
hysteresis = <2000>; /* millicelsius */ |
| 116 |
type = "passive"; |
| 117 |
}; |
| 118 |
|
| 119 |
ppvar_bigcpu_alert: ppvar-bigcpu-alert { |
| 120 |
temperature = <50000>; /* millicelsius */ |
| 121 |
hysteresis = <2000>; /* millicelsius */ |
| 122 |
type = "passive"; |
| 123 |
}; |
| 124 |
|
| 125 |
ppvar_bigcpu_crit: ppvar-bigcpu-crit { |
| 126 |
temperature = <90000>; /* millicelsius */ |
| 127 |
hysteresis = <0>; /* millicelsius */ |
| 128 |
type = "critical"; |
| 129 |
}; |
| 130 |
}; |
| 131 |
|
| 132 |
cooling-maps { |
| 133 |
map0 { |
| 134 |
trip = <&ppvar_bigcpu_alert>; |
| 135 |
cooling-device = |
| 136 |
<&cpu_l0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| 137 |
<&cpu_l1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| 138 |
<&cpu_l2 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| 139 |
<&cpu_l3 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| 140 |
contribution = <4096>; |
| 141 |
}; |
| 142 |
map1 { |
| 143 |
trip = <&ppvar_bigcpu_alert>; |
| 144 |
cooling-device = |
| 145 |
<&cpu_b0 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>, |
| 146 |
<&cpu_b1 THERMAL_NO_LIMIT THERMAL_NO_LIMIT>; |
| 147 |
contribution = <1024>; |
| 148 |
}; |
| 149 |
}; |
| 150 |
}; |
| 151 |
|
| 152 |
litcpu_reg_thermal: litcpu-reg-thermal { |
| 153 |
polling-delay-passive = <100>; /* milliseconds */ |
| 154 |
polling-delay = <1000>; /* milliseconds */ |
| 155 |
thermal-sensors = <&thermistor_ppvar_litcpu 0>; |
| 156 |
sustainable-power = <4000>; |
| 157 |
|
| 158 |
ppvar_litcpu_trips: trips { |
| 159 |
ppvar_litcpu_on: ppvar-litcpu-on { |
| 160 |
temperature = <40000>; /* millicelsius */ |
| 161 |
hysteresis = <2000>; /* millicelsius */ |
| 162 |
type = "passive"; |
| 163 |
}; |
| 164 |
|
| 165 |
ppvar_litcpu_alert: ppvar-litcpu-alert { |
| 166 |
temperature = <50000>; /* millicelsius */ |
| 167 |
hysteresis = <2000>; /* millicelsius */ |
| 168 |
type = "passive"; |
| 169 |
}; |
| 170 |
|
| 171 |
ppvar_litcpu_crit: ppvar-litcpu-crit { |
| 172 |
temperature = <90000>; /* millicelsius */ |
| 173 |
hysteresis = <0>; /* millicelsius */ |
| 174 |
type = "critical"; |
| 175 |
}; |
| 176 |
}; |
| 177 |
}; |
| 178 |
}; |
| 179 |
|
| 180 |
ap_i2c_tpm: &i2c0 { |
| 181 |
status = "okay"; |
| 182 |
|
| 183 |
clock-frequency = <400000>; |
| 184 |
|
| 185 |
/* These are relatively safe rise/fall times. */ |
| 186 |
i2c-scl-falling-time-ns = <50>; |
| 187 |
i2c-scl-rising-time-ns = <300>; |
| 188 |
|
| 189 |
tpm: tpm@20 { |
| 190 |
compatible = "infineon,slb9645tt"; |
| 191 |
reg = <0x20>; |
| 192 |
powered-while-suspended; |
| 193 |
}; |
| 194 |
}; |
| 195 |
|
| 196 |
ap_i2c_dig: &i2c2 { |
| 197 |
status = "okay"; |
| 198 |
|
| 199 |
clock-frequency = <400000>; |
| 200 |
|
| 201 |
/* These are relatively safe rise/fall times. */ |
| 202 |
i2c-scl-falling-time-ns = <50>; |
| 203 |
i2c-scl-rising-time-ns = <300>; |
| 204 |
|
| 205 |
digitizer: digitizer@9 { |
| 206 |
/* wacom,w9013 */ |
| 207 |
compatible = "hid-over-i2c"; |
| 208 |
reg = <0x9>; |
| 209 |
pinctrl-names = "default"; |
| 210 |
pinctrl-0 = <&cpu1_dig_irq_l &cpu1_dig_pdct_l>; |
| 211 |
|
| 212 |
vdd-supply = <&p3_3v_dig>; |
| 213 |
post-power-on-delay-ms = <100>; |
| 214 |
|
| 215 |
interrupt-parent = <&gpio2>; |
| 216 |
interrupts = <4 IRQ_TYPE_LEVEL_LOW>; |
| 217 |
|
| 218 |
hid-descr-addr = <0x1>; |
| 219 |
}; |
| 220 |
}; |
| 221 |
|
| 222 |
/* Adjustments to things in the gru baseboard */ |
| 223 |
|
| 224 |
&ap_i2c_tp { |
| 225 |
trackpad@4a { |
| 226 |
compatible = "atmel,maxtouch"; |
| 227 |
reg = <0x4a>; |
| 228 |
pinctrl-names = "default"; |
| 229 |
pinctrl-0 = <&trackpad_int_l>; |
| 230 |
interrupt-parent = <&gpio1>; |
| 231 |
interrupts = <4 IRQ_TYPE_LEVEL_LOW>; |
| 232 |
linux,gpio-keymap = <KEY_RESERVED |
| 233 |
KEY_RESERVED |
| 234 |
KEY_RESERVED |
| 235 |
BTN_LEFT>; |
| 236 |
wakeup-source; |
| 237 |
}; |
| 238 |
}; |
| 239 |
|
| 240 |
&ap_i2c_ts { |
| 241 |
touchscreen@4b { |
| 242 |
compatible = "atmel,maxtouch"; |
| 243 |
reg = <0x4b>; |
| 244 |
pinctrl-names = "default"; |
| 245 |
pinctrl-0 = <&touch_int_l>; |
| 246 |
interrupt-parent = <&gpio3>; |
| 247 |
interrupts = <13 IRQ_TYPE_LEVEL_LOW>; |
| 248 |
}; |
| 249 |
}; |
| 250 |
|
| 251 |
&ppvar_bigcpu_pwm { |
| 252 |
regulator-min-microvolt = <798674>; |
| 253 |
regulator-max-microvolt = <1302172>; |
| 254 |
}; |
| 255 |
|
| 256 |
&ppvar_bigcpu { |
| 257 |
regulator-min-microvolt = <798674>; |
| 258 |
regulator-max-microvolt = <1302172>; |
| 259 |
ctrl-voltage-range = <798674 1302172>; |
| 260 |
}; |
| 261 |
|
| 262 |
&ppvar_litcpu_pwm { |
| 263 |
regulator-min-microvolt = <799065>; |
| 264 |
regulator-max-microvolt = <1303738>; |
| 265 |
}; |
| 266 |
|
| 267 |
&ppvar_litcpu { |
| 268 |
regulator-min-microvolt = <799065>; |
| 269 |
regulator-max-microvolt = <1303738>; |
| 270 |
ctrl-voltage-range = <799065 1303738>; |
| 271 |
}; |
| 272 |
|
| 273 |
&ppvar_gpu_pwm { |
| 274 |
regulator-min-microvolt = <785782>; |
| 275 |
regulator-max-microvolt = <1217729>; |
| 276 |
}; |
| 277 |
|
| 278 |
&ppvar_gpu { |
| 279 |
regulator-min-microvolt = <785782>; |
| 280 |
regulator-max-microvolt = <1217729>; |
| 281 |
ctrl-voltage-range = <785782 1217729>; |
| 282 |
}; |
| 283 |
|
| 284 |
&ppvar_centerlogic_pwm { |
| 285 |
regulator-min-microvolt = <800069>; |
| 286 |
regulator-max-microvolt = <1049692>; |
| 287 |
}; |
| 288 |
|
| 289 |
&ppvar_centerlogic { |
| 290 |
regulator-min-microvolt = <800069>; |
| 291 |
regulator-max-microvolt = <1049692>; |
| 292 |
ctrl-voltage-range = <800069 1049692>; |
| 293 |
}; |
| 294 |
|
| 295 |
&saradc { |
| 296 |
status = "okay"; |
| 297 |
vref-supply = <&pp1800_ap_io>; |
| 298 |
}; |
| 299 |
|
| 300 |
&mvl_wifi { |
| 301 |
marvell,wakeup-pin = <14>; /* GPIO_14 on Marvell */ |
| 302 |
}; |
| 303 |
|
| 304 |
&pinctrl { |
| 305 |
digitizer { |
| 306 |
/* Has external pullup */ |
| 307 |
cpu1_dig_irq_l: cpu1-dig-irq-l { |
| 308 |
rockchip,pins = <2 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>; |
| 309 |
}; |
| 310 |
|
| 311 |
/* Has external pullup */ |
| 312 |
cpu1_dig_pdct_l: cpu1-dig-pdct-l { |
| 313 |
rockchip,pins = <2 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>; |
| 314 |
}; |
| 315 |
}; |
| 316 |
|
| 317 |
discretes { |
| 318 |
cpu3_pen_pwr_en: cpu3-pen-pwr-en { |
| 319 |
rockchip,pins = <4 RK_PD6 RK_FUNC_GPIO &pcfg_pull_none>; |
| 320 |
}; |
| 321 |
}; |
| 322 |
|
| 323 |
pen { |
| 324 |
cpu1_pen_eject: cpu1-pen-eject { |
| 325 |
rockchip,pins = <0 RK_PB5 RK_FUNC_GPIO &pcfg_pull_up>; |
| 326 |
}; |
| 327 |
}; |
| 328 |
}; |