| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Copyright (c) 2015 Caesar Wang <[email protected]> |
| 4 |
*/ |
| 5 |
|
| 6 |
#include <dt-bindings/input/input.h> |
| 7 |
#include <dt-bindings/pwm/pwm.h> |
| 8 |
#include "rk3368.dtsi" |
| 9 |
|
| 10 |
/ { |
| 11 |
aliases { |
| 12 |
ethernet0 = &gmac; |
| 13 |
mmc0 = &emmc; |
| 14 |
}; |
| 15 |
|
| 16 |
chosen { |
| 17 |
stdout-path = "serial2:115200n8"; |
| 18 |
}; |
| 19 |
|
| 20 |
memory@0 { |
| 21 |
device_type = "memory"; |
| 22 |
reg = <0x0 0x0 0x0 0x40000000>; |
| 23 |
}; |
| 24 |
|
| 25 |
backlight: backlight { |
| 26 |
compatible = "pwm-backlight"; |
| 27 |
brightness-levels = < |
| 28 |
0 1 2 3 4 5 6 7 |
| 29 |
8 9 10 11 12 13 14 15 |
| 30 |
16 17 18 19 20 21 22 23 |
| 31 |
24 25 26 27 28 29 30 31 |
| 32 |
32 33 34 35 36 37 38 39 |
| 33 |
40 41 42 43 44 45 46 47 |
| 34 |
48 49 50 51 52 53 54 55 |
| 35 |
56 57 58 59 60 61 62 63 |
| 36 |
64 65 66 67 68 69 70 71 |
| 37 |
72 73 74 75 76 77 78 79 |
| 38 |
80 81 82 83 84 85 86 87 |
| 39 |
88 89 90 91 92 93 94 95 |
| 40 |
96 97 98 99 100 101 102 103 |
| 41 |
104 105 106 107 108 109 110 111 |
| 42 |
112 113 114 115 116 117 118 119 |
| 43 |
120 121 122 123 124 125 126 127 |
| 44 |
128 129 130 131 132 133 134 135 |
| 45 |
136 137 138 139 140 141 142 143 |
| 46 |
144 145 146 147 148 149 150 151 |
| 47 |
152 153 154 155 156 157 158 159 |
| 48 |
160 161 162 163 164 165 166 167 |
| 49 |
168 169 170 171 172 173 174 175 |
| 50 |
176 177 178 179 180 181 182 183 |
| 51 |
184 185 186 187 188 189 190 191 |
| 52 |
192 193 194 195 196 197 198 199 |
| 53 |
200 201 202 203 204 205 206 207 |
| 54 |
208 209 210 211 212 213 214 215 |
| 55 |
216 217 218 219 220 221 222 223 |
| 56 |
224 225 226 227 228 229 230 231 |
| 57 |
232 233 234 235 236 237 238 239 |
| 58 |
240 241 242 243 244 245 246 247 |
| 59 |
248 249 250 251 252 253 254 255>; |
| 60 |
default-brightness-level = <128>; |
| 61 |
enable-gpios = <&gpio0 RK_PC4 GPIO_ACTIVE_HIGH>; |
| 62 |
pinctrl-names = "default"; |
| 63 |
pinctrl-0 = <&bl_en>; |
| 64 |
pwms = <&pwm0 0 1000000 PWM_POLARITY_INVERTED>; |
| 65 |
}; |
| 66 |
|
| 67 |
emmc_pwrseq: emmc-pwrseq { |
| 68 |
compatible = "mmc-pwrseq-emmc"; |
| 69 |
pinctrl-0 = <&emmc_reset>; |
| 70 |
pinctrl-names = "default"; |
| 71 |
reset-gpios = <&gpio2 RK_PA3 GPIO_ACTIVE_HIGH>; |
| 72 |
}; |
| 73 |
|
| 74 |
keys: gpio-keys { |
| 75 |
compatible = "gpio-keys"; |
| 76 |
pinctrl-names = "default"; |
| 77 |
pinctrl-0 = <&pwr_key>; |
| 78 |
|
| 79 |
key-power { |
| 80 |
wakeup-source; |
| 81 |
gpios = <&gpio0 RK_PA2 GPIO_ACTIVE_LOW>; |
| 82 |
label = "GPIO Power"; |
| 83 |
linux,code = <KEY_POWER>; |
| 84 |
}; |
| 85 |
}; |
| 86 |
|
| 87 |
/* supplies both host and otg */ |
| 88 |
vcc_host: regulator-vcc-host { |
| 89 |
compatible = "regulator-fixed"; |
| 90 |
enable-active-high; |
| 91 |
gpio = <&gpio0 RK_PA4 GPIO_ACTIVE_HIGH>; |
| 92 |
pinctrl-names = "default"; |
| 93 |
pinctrl-0 = <&host_vbus_drv>; |
| 94 |
regulator-name = "vcc_host"; |
| 95 |
regulator-always-on; |
| 96 |
regulator-boot-on; |
| 97 |
vin-supply = <&vcc_sys>; |
| 98 |
}; |
| 99 |
|
| 100 |
vcc_lan: regulator-vcc-lan { |
| 101 |
compatible = "regulator-fixed"; |
| 102 |
regulator-name = "vcc_lan"; |
| 103 |
regulator-min-microvolt = <3300000>; |
| 104 |
regulator-max-microvolt = <3300000>; |
| 105 |
regulator-always-on; |
| 106 |
regulator-boot-on; |
| 107 |
vin-supply = <&vcc_io>; |
| 108 |
}; |
| 109 |
|
| 110 |
vcc_sys: regulator-vcc-sys { |
| 111 |
compatible = "regulator-fixed"; |
| 112 |
regulator-name = "vcc_sys"; |
| 113 |
regulator-min-microvolt = <5000000>; |
| 114 |
regulator-max-microvolt = <5000000>; |
| 115 |
regulator-always-on; |
| 116 |
regulator-boot-on; |
| 117 |
}; |
| 118 |
}; |
| 119 |
|
| 120 |
&emmc { |
| 121 |
bus-width = <8>; |
| 122 |
cap-mmc-highspeed; |
| 123 |
mmc-pwrseq = <&emmc_pwrseq>; |
| 124 |
non-removable; |
| 125 |
pinctrl-names = "default"; |
| 126 |
pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>; |
| 127 |
status = "okay"; |
| 128 |
}; |
| 129 |
|
| 130 |
&gmac { |
| 131 |
phy-supply = <&vcc_lan>; |
| 132 |
phy-mode = "rmii"; |
| 133 |
clock_in_out = "output"; |
| 134 |
snps,reset-gpio = <&gpio3 RK_PB4 GPIO_ACTIVE_HIGH>; |
| 135 |
snps,reset-active-low; |
| 136 |
snps,reset-delays-us = <0 10000 1000000>; |
| 137 |
pinctrl-names = "default"; |
| 138 |
pinctrl-0 = <&rmii_pins>; |
| 139 |
tx_delay = <0x30>; |
| 140 |
rx_delay = <0x10>; |
| 141 |
status = "okay"; |
| 142 |
}; |
| 143 |
|
| 144 |
&i2c0 { |
| 145 |
status = "okay"; |
| 146 |
}; |
| 147 |
|
| 148 |
&pinctrl { |
| 149 |
pcfg_pull_none_drv_8ma: pcfg-pull-none-drv-8ma { |
| 150 |
bias-disable; |
| 151 |
drive-strength = <8>; |
| 152 |
}; |
| 153 |
|
| 154 |
pcfg_pull_up_drv_8ma: pcfg-pull-up-drv-8ma { |
| 155 |
bias-pull-up; |
| 156 |
drive-strength = <8>; |
| 157 |
}; |
| 158 |
|
| 159 |
backlight { |
| 160 |
bl_en: bl-en { |
| 161 |
rockchip,pins = <0 RK_PC4 RK_FUNC_GPIO &pcfg_pull_none>; |
| 162 |
}; |
| 163 |
}; |
| 164 |
|
| 165 |
emmc { |
| 166 |
emmc_bus8: emmc-bus8 { |
| 167 |
rockchip,pins = <1 RK_PC2 2 &pcfg_pull_up_drv_8ma>, |
| 168 |
<1 RK_PC3 2 &pcfg_pull_up_drv_8ma>, |
| 169 |
<1 RK_PC4 2 &pcfg_pull_up_drv_8ma>, |
| 170 |
<1 RK_PC5 2 &pcfg_pull_up_drv_8ma>, |
| 171 |
<1 RK_PC6 2 &pcfg_pull_up_drv_8ma>, |
| 172 |
<1 RK_PC7 2 &pcfg_pull_up_drv_8ma>, |
| 173 |
<1 RK_PD0 2 &pcfg_pull_up_drv_8ma>, |
| 174 |
<1 RK_PD1 2 &pcfg_pull_up_drv_8ma>; |
| 175 |
}; |
| 176 |
|
| 177 |
emmc-clk { |
| 178 |
rockchip,pins = <2 RK_PA4 2 &pcfg_pull_none_drv_8ma>; |
| 179 |
}; |
| 180 |
|
| 181 |
emmc-cmd { |
| 182 |
rockchip,pins = <1 RK_PD2 2 &pcfg_pull_up_drv_8ma>; |
| 183 |
}; |
| 184 |
|
| 185 |
emmc_reset: emmc-reset { |
| 186 |
rockchip,pins = <2 RK_PA3 RK_FUNC_GPIO &pcfg_pull_none>; |
| 187 |
}; |
| 188 |
}; |
| 189 |
|
| 190 |
keys { |
| 191 |
pwr_key: pwr-key { |
| 192 |
rockchip,pins = <0 RK_PA2 RK_FUNC_GPIO &pcfg_pull_up>; |
| 193 |
}; |
| 194 |
}; |
| 195 |
|
| 196 |
pmic { |
| 197 |
pmic_int: pmic-int { |
| 198 |
rockchip,pins = <0 RK_PA1 RK_FUNC_GPIO &pcfg_pull_up>; |
| 199 |
}; |
| 200 |
}; |
| 201 |
|
| 202 |
sdio { |
| 203 |
wifi_reg_on: wifi-reg-on { |
| 204 |
rockchip,pins = <3 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>; |
| 205 |
}; |
| 206 |
|
| 207 |
bt_rst: bt-rst { |
| 208 |
rockchip,pins = <3 RK_PA5 RK_FUNC_GPIO &pcfg_pull_none>; |
| 209 |
}; |
| 210 |
}; |
| 211 |
|
| 212 |
usb { |
| 213 |
host_vbus_drv: host-vbus-drv { |
| 214 |
rockchip,pins = <0 RK_PA4 RK_FUNC_GPIO &pcfg_pull_none>; |
| 215 |
}; |
| 216 |
}; |
| 217 |
}; |
| 218 |
|
| 219 |
&pwm0 { |
| 220 |
status = "okay"; |
| 221 |
}; |
| 222 |
|
| 223 |
&tsadc { |
| 224 |
rockchip,hw-tshut-mode = <0>; /* tshut mode 0:CRU 1:GPIO */ |
| 225 |
rockchip,hw-tshut-polarity = <0>; /* tshut polarity 0:LOW 1:HIGH */ |
| 226 |
status = "okay"; |
| 227 |
}; |
| 228 |
|
| 229 |
&uart2 { |
| 230 |
status = "okay"; |
| 231 |
}; |
| 232 |
|
| 233 |
&usb_host0_ehci { |
| 234 |
status = "okay"; |
| 235 |
}; |
| 236 |
|
| 237 |
&usb_otg { |
| 238 |
dr_mode = "host"; |
| 239 |
status = "okay"; |
| 240 |
}; |
| 241 |
|
| 242 |
&wdt { |
| 243 |
status = "okay"; |
| 244 |
}; |