| 1 |
// SPDX-License-Identifier: BSD-3-Clause |
| 2 |
/* |
| 3 |
* Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved. |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
|
| 8 |
#include <dt-bindings/gpio/gpio.h> |
| 9 |
#include <dt-bindings/input/gpio-keys.h> |
| 10 |
#include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| 11 |
|
| 12 |
#include "hamoa.dtsi" |
| 13 |
#include "hamoa-pmics.dtsi" |
| 14 |
|
| 15 |
/ { |
| 16 |
model = "Lenovo Yoga Slim 7x"; |
| 17 |
compatible = "lenovo,yoga-slim7x", "qcom,x1e80100"; |
| 18 |
|
| 19 |
aliases { |
| 20 |
serial0 = &uart21; |
| 21 |
serial1 = &uart14; |
| 22 |
}; |
| 23 |
|
| 24 |
chosen { |
| 25 |
stdout-path = "serial0:115200n8"; |
| 26 |
}; |
| 27 |
|
| 28 |
gpio-keys { |
| 29 |
compatible = "gpio-keys"; |
| 30 |
|
| 31 |
pinctrl-0 = <&hall_int_n_default>; |
| 32 |
pinctrl-names = "default"; |
| 33 |
|
| 34 |
switch-lid { |
| 35 |
gpios = <&tlmm 92 GPIO_ACTIVE_LOW>; |
| 36 |
linux,input-type = <EV_SW>; |
| 37 |
linux,code = <SW_LID>; |
| 38 |
wakeup-source; |
| 39 |
wakeup-event-action = <EV_ACT_DEASSERTED>; |
| 40 |
}; |
| 41 |
}; |
| 42 |
|
| 43 |
pmic-glink { |
| 44 |
compatible = "qcom,x1e80100-pmic-glink", |
| 45 |
"qcom,sm8550-pmic-glink", |
| 46 |
"qcom,pmic-glink"; |
| 47 |
#address-cells = <1>; |
| 48 |
#size-cells = <0>; |
| 49 |
orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, |
| 50 |
<&tlmm 123 GPIO_ACTIVE_HIGH>, |
| 51 |
<&tlmm 125 GPIO_ACTIVE_HIGH>; |
| 52 |
|
| 53 |
/* Left-side rear port */ |
| 54 |
connector@0 { |
| 55 |
compatible = "usb-c-connector"; |
| 56 |
reg = <0>; |
| 57 |
power-role = "dual"; |
| 58 |
data-role = "dual"; |
| 59 |
|
| 60 |
ports { |
| 61 |
#address-cells = <1>; |
| 62 |
#size-cells = <0>; |
| 63 |
|
| 64 |
port@0 { |
| 65 |
reg = <0>; |
| 66 |
|
| 67 |
pmic_glink_ss0_hs_in: endpoint { |
| 68 |
remote-endpoint = <&usb_1_ss0_dwc3_hs>; |
| 69 |
}; |
| 70 |
}; |
| 71 |
|
| 72 |
port@1 { |
| 73 |
reg = <1>; |
| 74 |
|
| 75 |
pmic_glink_ss0_ss_in: endpoint { |
| 76 |
remote-endpoint = <&retimer_ss0_ss_out>; |
| 77 |
}; |
| 78 |
}; |
| 79 |
|
| 80 |
port@2 { |
| 81 |
reg = <2>; |
| 82 |
|
| 83 |
pmic_glink_ss0_con_sbu_in: endpoint { |
| 84 |
remote-endpoint = <&retimer_ss0_con_sbu_out>; |
| 85 |
}; |
| 86 |
}; |
| 87 |
}; |
| 88 |
}; |
| 89 |
|
| 90 |
/* Left-side front port */ |
| 91 |
connector@1 { |
| 92 |
compatible = "usb-c-connector"; |
| 93 |
reg = <1>; |
| 94 |
power-role = "dual"; |
| 95 |
data-role = "dual"; |
| 96 |
|
| 97 |
ports { |
| 98 |
#address-cells = <1>; |
| 99 |
#size-cells = <0>; |
| 100 |
|
| 101 |
port@0 { |
| 102 |
reg = <0>; |
| 103 |
|
| 104 |
pmic_glink_ss1_hs_in: endpoint { |
| 105 |
remote-endpoint = <&usb_1_ss1_dwc3_hs>; |
| 106 |
}; |
| 107 |
}; |
| 108 |
|
| 109 |
port@1 { |
| 110 |
reg = <1>; |
| 111 |
|
| 112 |
pmic_glink_ss1_ss_in: endpoint { |
| 113 |
remote-endpoint = <&retimer_ss1_ss_out>; |
| 114 |
}; |
| 115 |
}; |
| 116 |
|
| 117 |
port@2 { |
| 118 |
reg = <2>; |
| 119 |
|
| 120 |
pmic_glink_ss1_con_sbu_in: endpoint { |
| 121 |
remote-endpoint = <&retimer_ss1_con_sbu_out>; |
| 122 |
}; |
| 123 |
}; |
| 124 |
}; |
| 125 |
}; |
| 126 |
|
| 127 |
/* Right-side port */ |
| 128 |
connector@2 { |
| 129 |
compatible = "usb-c-connector"; |
| 130 |
reg = <2>; |
| 131 |
power-role = "dual"; |
| 132 |
data-role = "dual"; |
| 133 |
|
| 134 |
ports { |
| 135 |
#address-cells = <1>; |
| 136 |
#size-cells = <0>; |
| 137 |
|
| 138 |
port@0 { |
| 139 |
reg = <0>; |
| 140 |
|
| 141 |
pmic_glink_ss2_hs_in: endpoint { |
| 142 |
remote-endpoint = <&usb_1_ss2_dwc3_hs>; |
| 143 |
}; |
| 144 |
}; |
| 145 |
|
| 146 |
port@1 { |
| 147 |
reg = <1>; |
| 148 |
|
| 149 |
pmic_glink_ss2_ss_in: endpoint { |
| 150 |
remote-endpoint = <&retimer_ss2_ss_out>; |
| 151 |
}; |
| 152 |
}; |
| 153 |
|
| 154 |
port@2 { |
| 155 |
reg = <2>; |
| 156 |
|
| 157 |
pmic_glink_ss2_con_sbu_in: endpoint { |
| 158 |
remote-endpoint = <&retimer_ss2_con_sbu_out>; |
| 159 |
}; |
| 160 |
}; |
| 161 |
}; |
| 162 |
}; |
| 163 |
}; |
| 164 |
|
| 165 |
reserved-memory { |
| 166 |
linux,cma { |
| 167 |
compatible = "shared-dma-pool"; |
| 168 |
size = <0x0 0x8000000>; |
| 169 |
reusable; |
| 170 |
linux,cma-default; |
| 171 |
}; |
| 172 |
}; |
| 173 |
|
| 174 |
sound { |
| 175 |
compatible = "qcom,x1e80100-sndcard"; |
| 176 |
model = "X1E80100-LENOVO-Yoga-Slim7x"; |
| 177 |
audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT", |
| 178 |
"TweeterLeft IN", "WSA WSA_SPK2 OUT", |
| 179 |
"WooferRight IN", "WSA2 WSA_SPK2 OUT", |
| 180 |
"TweeterRight IN", "WSA2 WSA_SPK2 OUT", |
| 181 |
"VA DMIC0", "vdd-micb", |
| 182 |
"VA DMIC1", "vdd-micb", |
| 183 |
"VA DMIC2", "vdd-micb", |
| 184 |
"VA DMIC3", "vdd-micb"; |
| 185 |
|
| 186 |
wsa-dai-link { |
| 187 |
link-name = "WSA Playback"; |
| 188 |
|
| 189 |
cpu { |
| 190 |
sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>; |
| 191 |
}; |
| 192 |
|
| 193 |
codec { |
| 194 |
sound-dai = <&left_woofer>, <&left_tweeter>, |
| 195 |
<&swr0 0>, <&lpass_wsamacro 0>, |
| 196 |
<&right_woofer>, <&right_tweeter>, |
| 197 |
<&swr3 0>, <&lpass_wsa2macro 0>; |
| 198 |
}; |
| 199 |
|
| 200 |
platform { |
| 201 |
sound-dai = <&q6apm>; |
| 202 |
}; |
| 203 |
}; |
| 204 |
|
| 205 |
va-dai-link { |
| 206 |
link-name = "VA Capture"; |
| 207 |
|
| 208 |
cpu { |
| 209 |
sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>; |
| 210 |
}; |
| 211 |
|
| 212 |
codec { |
| 213 |
sound-dai = <&lpass_vamacro 0>; |
| 214 |
}; |
| 215 |
|
| 216 |
platform { |
| 217 |
sound-dai = <&q6apm>; |
| 218 |
}; |
| 219 |
}; |
| 220 |
}; |
| 221 |
|
| 222 |
vreg_edp_3p3: regulator-edp-3p3 { |
| 223 |
compatible = "regulator-fixed"; |
| 224 |
|
| 225 |
regulator-name = "VREG_EDP_3P3"; |
| 226 |
regulator-min-microvolt = <3300000>; |
| 227 |
regulator-max-microvolt = <3300000>; |
| 228 |
|
| 229 |
gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>; |
| 230 |
enable-active-high; |
| 231 |
|
| 232 |
pinctrl-0 = <&edp_reg_en>; |
| 233 |
pinctrl-names = "default"; |
| 234 |
|
| 235 |
regulator-boot-on; |
| 236 |
}; |
| 237 |
|
| 238 |
vreg_nvme: regulator-nvme { |
| 239 |
compatible = "regulator-fixed"; |
| 240 |
|
| 241 |
regulator-name = "VREG_NVME_3P3"; |
| 242 |
regulator-min-microvolt = <3300000>; |
| 243 |
regulator-max-microvolt = <3300000>; |
| 244 |
|
| 245 |
gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>; |
| 246 |
enable-active-high; |
| 247 |
|
| 248 |
pinctrl-0 = <&nvme_reg_en>; |
| 249 |
pinctrl-names = "default"; |
| 250 |
|
| 251 |
regulator-boot-on; |
| 252 |
}; |
| 253 |
|
| 254 |
vreg_rtmr0_1p15: regulator-rtmr0-1p15 { |
| 255 |
compatible = "regulator-fixed"; |
| 256 |
|
| 257 |
regulator-name = "VREG_RTMR0_1P15"; |
| 258 |
regulator-min-microvolt = <1150000>; |
| 259 |
regulator-max-microvolt = <1150000>; |
| 260 |
|
| 261 |
gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>; |
| 262 |
enable-active-high; |
| 263 |
|
| 264 |
pinctrl-0 = <&usb0_pwr_1p15_reg_en>; |
| 265 |
pinctrl-names = "default"; |
| 266 |
|
| 267 |
regulator-boot-on; |
| 268 |
}; |
| 269 |
|
| 270 |
vreg_rtmr0_1p8: regulator-rtmr0-1p8 { |
| 271 |
compatible = "regulator-fixed"; |
| 272 |
|
| 273 |
regulator-name = "VREG_RTMR0_1P8"; |
| 274 |
regulator-min-microvolt = <1800000>; |
| 275 |
regulator-max-microvolt = <1800000>; |
| 276 |
|
| 277 |
gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>; |
| 278 |
enable-active-high; |
| 279 |
|
| 280 |
pinctrl-0 = <&usb0_1p8_reg_en>; |
| 281 |
pinctrl-names = "default"; |
| 282 |
|
| 283 |
regulator-boot-on; |
| 284 |
}; |
| 285 |
|
| 286 |
vreg_rtmr0_3p3: regulator-rtmr0-3p3 { |
| 287 |
compatible = "regulator-fixed"; |
| 288 |
|
| 289 |
regulator-name = "VREG_RTMR0_3P3"; |
| 290 |
regulator-min-microvolt = <3300000>; |
| 291 |
regulator-max-microvolt = <3300000>; |
| 292 |
|
| 293 |
gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>; |
| 294 |
enable-active-high; |
| 295 |
|
| 296 |
pinctrl-0 = <&usb0_3p3_reg_en>; |
| 297 |
pinctrl-names = "default"; |
| 298 |
|
| 299 |
regulator-boot-on; |
| 300 |
}; |
| 301 |
|
| 302 |
vreg_rtmr1_1p15: regulator-rtmr1-1p15 { |
| 303 |
compatible = "regulator-fixed"; |
| 304 |
|
| 305 |
regulator-name = "VREG_RTMR1_1P15"; |
| 306 |
regulator-min-microvolt = <1150000>; |
| 307 |
regulator-max-microvolt = <1150000>; |
| 308 |
|
| 309 |
gpio = <&tlmm 188 GPIO_ACTIVE_HIGH>; |
| 310 |
enable-active-high; |
| 311 |
|
| 312 |
pinctrl-0 = <&usb1_pwr_1p15_reg_en>; |
| 313 |
pinctrl-names = "default"; |
| 314 |
|
| 315 |
regulator-boot-on; |
| 316 |
}; |
| 317 |
|
| 318 |
vreg_rtmr1_1p8: regulator-rtmr1-1p8 { |
| 319 |
compatible = "regulator-fixed"; |
| 320 |
|
| 321 |
regulator-name = "VREG_RTMR1_1P8"; |
| 322 |
regulator-min-microvolt = <1800000>; |
| 323 |
regulator-max-microvolt = <1800000>; |
| 324 |
|
| 325 |
gpio = <&tlmm 175 GPIO_ACTIVE_HIGH>; |
| 326 |
enable-active-high; |
| 327 |
|
| 328 |
pinctrl-0 = <&usb1_pwr_1p8_reg_en>; |
| 329 |
pinctrl-names = "default"; |
| 330 |
|
| 331 |
regulator-boot-on; |
| 332 |
}; |
| 333 |
|
| 334 |
vreg_rtmr1_3p3: regulator-rtmr1-3p3 { |
| 335 |
compatible = "regulator-fixed"; |
| 336 |
|
| 337 |
regulator-name = "VREG_RTMR1_3P3"; |
| 338 |
regulator-min-microvolt = <3300000>; |
| 339 |
regulator-max-microvolt = <3300000>; |
| 340 |
|
| 341 |
gpio = <&tlmm 186 GPIO_ACTIVE_HIGH>; |
| 342 |
enable-active-high; |
| 343 |
|
| 344 |
pinctrl-0 = <&usb1_pwr_3p3_reg_en>; |
| 345 |
pinctrl-names = "default"; |
| 346 |
|
| 347 |
regulator-boot-on; |
| 348 |
}; |
| 349 |
|
| 350 |
vreg_rtmr2_1p15: regulator-rtmr2-1p15 { |
| 351 |
compatible = "regulator-fixed"; |
| 352 |
|
| 353 |
regulator-name = "VREG_RTMR2_1P15"; |
| 354 |
regulator-min-microvolt = <1150000>; |
| 355 |
regulator-max-microvolt = <1150000>; |
| 356 |
|
| 357 |
gpio = <&tlmm 189 GPIO_ACTIVE_HIGH>; |
| 358 |
enable-active-high; |
| 359 |
|
| 360 |
pinctrl-0 = <&usb2_pwr_1p15_reg_en>; |
| 361 |
pinctrl-names = "default"; |
| 362 |
|
| 363 |
regulator-boot-on; |
| 364 |
}; |
| 365 |
|
| 366 |
vreg_rtmr2_1p8: regulator-rtmr2-1p8 { |
| 367 |
compatible = "regulator-fixed"; |
| 368 |
|
| 369 |
regulator-name = "VREG_RTMR2_1P8"; |
| 370 |
regulator-min-microvolt = <1800000>; |
| 371 |
regulator-max-microvolt = <1800000>; |
| 372 |
|
| 373 |
gpio = <&tlmm 126 GPIO_ACTIVE_HIGH>; |
| 374 |
enable-active-high; |
| 375 |
|
| 376 |
pinctrl-0 = <&usb2_pwr_1p8_reg_en>; |
| 377 |
pinctrl-names = "default"; |
| 378 |
|
| 379 |
regulator-boot-on; |
| 380 |
}; |
| 381 |
|
| 382 |
vreg_rtmr2_3p3: regulator-rtmr2-3p3 { |
| 383 |
compatible = "regulator-fixed"; |
| 384 |
|
| 385 |
regulator-name = "VREG_RTMR2_3P3"; |
| 386 |
regulator-min-microvolt = <3300000>; |
| 387 |
regulator-max-microvolt = <3300000>; |
| 388 |
|
| 389 |
gpio = <&tlmm 187 GPIO_ACTIVE_HIGH>; |
| 390 |
enable-active-high; |
| 391 |
|
| 392 |
pinctrl-0 = <&usb2_pwr_3p3_reg_en>; |
| 393 |
pinctrl-names = "default"; |
| 394 |
|
| 395 |
regulator-boot-on; |
| 396 |
}; |
| 397 |
|
| 398 |
vph_pwr: regulator-vph-pwr { |
| 399 |
compatible = "regulator-fixed"; |
| 400 |
|
| 401 |
regulator-name = "vph_pwr"; |
| 402 |
regulator-min-microvolt = <3700000>; |
| 403 |
regulator-max-microvolt = <3700000>; |
| 404 |
|
| 405 |
regulator-always-on; |
| 406 |
regulator-boot-on; |
| 407 |
}; |
| 408 |
|
| 409 |
vreg_wcn_3p3: regulator-wcn-3p3 { |
| 410 |
compatible = "regulator-fixed"; |
| 411 |
|
| 412 |
regulator-name = "VREG_WCN_3P3"; |
| 413 |
regulator-min-microvolt = <3300000>; |
| 414 |
regulator-max-microvolt = <3300000>; |
| 415 |
|
| 416 |
gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>; |
| 417 |
enable-active-high; |
| 418 |
|
| 419 |
pinctrl-0 = <&wcn_sw_en>; |
| 420 |
pinctrl-names = "default"; |
| 421 |
|
| 422 |
regulator-boot-on; |
| 423 |
}; |
| 424 |
|
| 425 |
/* |
| 426 |
* TODO: These two regulators are actually part of the removable M.2 |
| 427 |
* card and not the CRD mainboard. Need to describe this differently. |
| 428 |
* Functionally it works correctly, because all we need to do is to |
| 429 |
* turn on the actual 3.3V supply above. |
| 430 |
*/ |
| 431 |
vreg_wcn_0p95: regulator-wcn-0p95 { |
| 432 |
compatible = "regulator-fixed"; |
| 433 |
|
| 434 |
regulator-name = "VREG_WCN_0P95"; |
| 435 |
regulator-min-microvolt = <950000>; |
| 436 |
regulator-max-microvolt = <950000>; |
| 437 |
|
| 438 |
vin-supply = <&vreg_wcn_3p3>; |
| 439 |
}; |
| 440 |
|
| 441 |
vreg_wcn_1p9: regulator-wcn-1p9 { |
| 442 |
compatible = "regulator-fixed"; |
| 443 |
|
| 444 |
regulator-name = "VREG_WCN_1P9"; |
| 445 |
regulator-min-microvolt = <1900000>; |
| 446 |
regulator-max-microvolt = <1900000>; |
| 447 |
|
| 448 |
vin-supply = <&vreg_wcn_3p3>; |
| 449 |
}; |
| 450 |
|
| 451 |
wcn7850-pmu { |
| 452 |
compatible = "qcom,wcn7850-pmu"; |
| 453 |
|
| 454 |
vdd-supply = <&vreg_wcn_0p95>; |
| 455 |
vddio-supply = <&vreg_l15b_1p8>; |
| 456 |
vddaon-supply = <&vreg_wcn_0p95>; |
| 457 |
vdddig-supply = <&vreg_wcn_0p95>; |
| 458 |
vddrfa1p2-supply = <&vreg_wcn_1p9>; |
| 459 |
vddrfa1p8-supply = <&vreg_wcn_1p9>; |
| 460 |
|
| 461 |
wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>; |
| 462 |
bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>; |
| 463 |
|
| 464 |
pinctrl-0 = <&wcn_wlan_bt_en>; |
| 465 |
pinctrl-names = "default"; |
| 466 |
|
| 467 |
regulators { |
| 468 |
vreg_pmu_rfa_cmn: ldo0 { |
| 469 |
regulator-name = "vreg_pmu_rfa_cmn"; |
| 470 |
}; |
| 471 |
|
| 472 |
vreg_pmu_aon_0p59: ldo1 { |
| 473 |
regulator-name = "vreg_pmu_aon_0p59"; |
| 474 |
}; |
| 475 |
|
| 476 |
vreg_pmu_wlcx_0p8: ldo2 { |
| 477 |
regulator-name = "vreg_pmu_wlcx_0p8"; |
| 478 |
}; |
| 479 |
|
| 480 |
vreg_pmu_wlmx_0p85: ldo3 { |
| 481 |
regulator-name = "vreg_pmu_wlmx_0p85"; |
| 482 |
}; |
| 483 |
|
| 484 |
vreg_pmu_btcmx_0p85: ldo4 { |
| 485 |
regulator-name = "vreg_pmu_btcmx_0p85"; |
| 486 |
}; |
| 487 |
|
| 488 |
vreg_pmu_rfa_0p8: ldo5 { |
| 489 |
regulator-name = "vreg_pmu_rfa_0p8"; |
| 490 |
}; |
| 491 |
|
| 492 |
vreg_pmu_rfa_1p2: ldo6 { |
| 493 |
regulator-name = "vreg_pmu_rfa_1p2"; |
| 494 |
}; |
| 495 |
|
| 496 |
vreg_pmu_rfa_1p8: ldo7 { |
| 497 |
regulator-name = "vreg_pmu_rfa_1p8"; |
| 498 |
}; |
| 499 |
|
| 500 |
vreg_pmu_pcie_0p9: ldo8 { |
| 501 |
regulator-name = "vreg_pmu_pcie_0p9"; |
| 502 |
}; |
| 503 |
|
| 504 |
vreg_pmu_pcie_1p8: ldo9 { |
| 505 |
regulator-name = "vreg_pmu_pcie_1p8"; |
| 506 |
}; |
| 507 |
}; |
| 508 |
}; |
| 509 |
}; |
| 510 |
|
| 511 |
&apps_rsc { |
| 512 |
regulators-0 { |
| 513 |
compatible = "qcom,pm8550-rpmh-regulators"; |
| 514 |
qcom,pmic-id = "b"; |
| 515 |
|
| 516 |
vdd-bob1-supply = <&vph_pwr>; |
| 517 |
vdd-bob2-supply = <&vph_pwr>; |
| 518 |
vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>; |
| 519 |
vdd-l2-l13-l14-supply = <&vreg_bob1>; |
| 520 |
vdd-l5-l16-supply = <&vreg_bob1>; |
| 521 |
vdd-l6-l7-supply = <&vreg_bob2>; |
| 522 |
vdd-l8-l9-supply = <&vreg_bob1>; |
| 523 |
vdd-l12-supply = <&vreg_s5j_1p2>; |
| 524 |
vdd-l15-supply = <&vreg_s4c_1p8>; |
| 525 |
vdd-l17-supply = <&vreg_bob2>; |
| 526 |
|
| 527 |
vreg_bob1: bob1 { |
| 528 |
regulator-name = "vreg_bob1"; |
| 529 |
regulator-min-microvolt = <3008000>; |
| 530 |
regulator-max-microvolt = <3960000>; |
| 531 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 532 |
}; |
| 533 |
|
| 534 |
vreg_bob2: bob2 { |
| 535 |
regulator-name = "vreg_bob2"; |
| 536 |
regulator-min-microvolt = <2504000>; |
| 537 |
regulator-max-microvolt = <3008000>; |
| 538 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 539 |
}; |
| 540 |
|
| 541 |
vreg_l1b_1p8: ldo1 { |
| 542 |
regulator-name = "vreg_l1b_1p8"; |
| 543 |
regulator-min-microvolt = <1800000>; |
| 544 |
regulator-max-microvolt = <1800000>; |
| 545 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 546 |
}; |
| 547 |
|
| 548 |
vreg_l2b_3p0: ldo2 { |
| 549 |
regulator-name = "vreg_l2b_3p0"; |
| 550 |
regulator-min-microvolt = <3072000>; |
| 551 |
regulator-max-microvolt = <3100000>; |
| 552 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 553 |
}; |
| 554 |
|
| 555 |
vreg_l8b_3p0: ldo8 { |
| 556 |
regulator-name = "vreg_l8b_3p0"; |
| 557 |
regulator-min-microvolt = <3072000>; |
| 558 |
regulator-max-microvolt = <3072000>; |
| 559 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 560 |
}; |
| 561 |
|
| 562 |
vreg_l12b_1p2: ldo12 { |
| 563 |
regulator-name = "vreg_l12b_1p2"; |
| 564 |
regulator-min-microvolt = <1200000>; |
| 565 |
regulator-max-microvolt = <1200000>; |
| 566 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 567 |
regulator-always-on; |
| 568 |
}; |
| 569 |
|
| 570 |
vreg_l14b_3p0: ldo14 { |
| 571 |
regulator-name = "vreg_l14b_3p0"; |
| 572 |
regulator-min-microvolt = <3072000>; |
| 573 |
regulator-max-microvolt = <3072000>; |
| 574 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 575 |
}; |
| 576 |
|
| 577 |
vreg_l15b_1p8: ldo15 { |
| 578 |
regulator-name = "vreg_l15b_1p8"; |
| 579 |
regulator-min-microvolt = <1800000>; |
| 580 |
regulator-max-microvolt = <1800000>; |
| 581 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 582 |
regulator-always-on; |
| 583 |
}; |
| 584 |
}; |
| 585 |
|
| 586 |
regulators-1 { |
| 587 |
compatible = "qcom,pm8550ve-rpmh-regulators"; |
| 588 |
qcom,pmic-id = "c"; |
| 589 |
|
| 590 |
vdd-l1-supply = <&vreg_s5j_1p2>; |
| 591 |
vdd-l2-supply = <&vreg_s1f_0p7>; |
| 592 |
vdd-l3-supply = <&vreg_s1f_0p7>; |
| 593 |
vdd-s4-supply = <&vph_pwr>; |
| 594 |
|
| 595 |
vreg_s4c_1p8: smps4 { |
| 596 |
regulator-name = "vreg_s4c_1p8"; |
| 597 |
regulator-min-microvolt = <1856000>; |
| 598 |
regulator-max-microvolt = <2000000>; |
| 599 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 600 |
}; |
| 601 |
|
| 602 |
vreg_l1c_1p2: ldo1 { |
| 603 |
regulator-name = "vreg_l1c_1p2"; |
| 604 |
regulator-min-microvolt = <1200000>; |
| 605 |
regulator-max-microvolt = <1200000>; |
| 606 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 607 |
}; |
| 608 |
|
| 609 |
vreg_l2c_0p8: ldo2 { |
| 610 |
regulator-name = "vreg_l2c_0p8"; |
| 611 |
regulator-min-microvolt = <880000>; |
| 612 |
regulator-max-microvolt = <920000>; |
| 613 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 614 |
}; |
| 615 |
|
| 616 |
vreg_l3c_0p8: ldo3 { |
| 617 |
regulator-name = "vreg_l3c_0p8"; |
| 618 |
regulator-min-microvolt = <880000>; |
| 619 |
regulator-max-microvolt = <920000>; |
| 620 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 621 |
}; |
| 622 |
}; |
| 623 |
|
| 624 |
regulators-2 { |
| 625 |
compatible = "qcom,pmc8380-rpmh-regulators"; |
| 626 |
qcom,pmic-id = "d"; |
| 627 |
|
| 628 |
vdd-l1-supply = <&vreg_s1f_0p7>; |
| 629 |
vdd-l2-supply = <&vreg_s1f_0p7>; |
| 630 |
vdd-l3-supply = <&vreg_s4c_1p8>; |
| 631 |
vdd-s1-supply = <&vph_pwr>; |
| 632 |
|
| 633 |
vreg_l1d_0p8: ldo1 { |
| 634 |
regulator-name = "vreg_l1d_0p8"; |
| 635 |
regulator-min-microvolt = <880000>; |
| 636 |
regulator-max-microvolt = <920000>; |
| 637 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 638 |
}; |
| 639 |
|
| 640 |
vreg_l2d_0p9: ldo2 { |
| 641 |
regulator-name = "vreg_l2d_0p9"; |
| 642 |
regulator-min-microvolt = <912000>; |
| 643 |
regulator-max-microvolt = <920000>; |
| 644 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 645 |
}; |
| 646 |
|
| 647 |
vreg_l3d_1p8: ldo3 { |
| 648 |
regulator-name = "vreg_l3d_1p8"; |
| 649 |
regulator-min-microvolt = <1800000>; |
| 650 |
regulator-max-microvolt = <1800000>; |
| 651 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 652 |
}; |
| 653 |
}; |
| 654 |
|
| 655 |
regulators-3 { |
| 656 |
compatible = "qcom,pmc8380-rpmh-regulators"; |
| 657 |
qcom,pmic-id = "e"; |
| 658 |
|
| 659 |
vdd-l2-supply = <&vreg_s1f_0p7>; |
| 660 |
vdd-l3-supply = <&vreg_s5j_1p2>; |
| 661 |
|
| 662 |
vreg_l2e_0p8: ldo2 { |
| 663 |
regulator-name = "vreg_l2e_0p8"; |
| 664 |
regulator-min-microvolt = <880000>; |
| 665 |
regulator-max-microvolt = <920000>; |
| 666 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 667 |
}; |
| 668 |
|
| 669 |
vreg_l3e_1p2: ldo3 { |
| 670 |
regulator-name = "vreg_l3e_1p2"; |
| 671 |
regulator-min-microvolt = <1200000>; |
| 672 |
regulator-max-microvolt = <1200000>; |
| 673 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 674 |
}; |
| 675 |
}; |
| 676 |
|
| 677 |
regulators-4 { |
| 678 |
compatible = "qcom,pmc8380-rpmh-regulators"; |
| 679 |
qcom,pmic-id = "f"; |
| 680 |
|
| 681 |
vdd-l1-supply = <&vreg_s5j_1p2>; |
| 682 |
vdd-l2-supply = <&vreg_s5j_1p2>; |
| 683 |
vdd-l3-supply = <&vreg_s5j_1p2>; |
| 684 |
vdd-s1-supply = <&vph_pwr>; |
| 685 |
|
| 686 |
vreg_s1f_0p7: smps1 { |
| 687 |
regulator-name = "vreg_s1f_0p7"; |
| 688 |
regulator-min-microvolt = <700000>; |
| 689 |
regulator-max-microvolt = <1100000>; |
| 690 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 691 |
}; |
| 692 |
|
| 693 |
vreg_l1f_1p0: ldo1 { |
| 694 |
regulator-name = "vreg_l1f_1p0"; |
| 695 |
regulator-min-microvolt = <1024000>; |
| 696 |
regulator-max-microvolt = <1024000>; |
| 697 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 698 |
}; |
| 699 |
|
| 700 |
vreg_l2f_1p0: ldo2 { |
| 701 |
regulator-name = "vreg_l2f_1p0"; |
| 702 |
regulator-min-microvolt = <1024000>; |
| 703 |
regulator-max-microvolt = <1024000>; |
| 704 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 705 |
}; |
| 706 |
|
| 707 |
vreg_l3f_1p0: ldo3 { |
| 708 |
regulator-name = "vreg_l3f_1p0"; |
| 709 |
regulator-min-microvolt = <1024000>; |
| 710 |
regulator-max-microvolt = <1024000>; |
| 711 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 712 |
}; |
| 713 |
}; |
| 714 |
|
| 715 |
regulators-6 { |
| 716 |
compatible = "qcom,pm8550ve-rpmh-regulators"; |
| 717 |
qcom,pmic-id = "i"; |
| 718 |
|
| 719 |
vdd-l1-supply = <&vreg_s4c_1p8>; |
| 720 |
vdd-l2-supply = <&vreg_s5j_1p2>; |
| 721 |
vdd-l3-supply = <&vreg_s1f_0p7>; |
| 722 |
vdd-s1-supply = <&vph_pwr>; |
| 723 |
vdd-s2-supply = <&vph_pwr>; |
| 724 |
|
| 725 |
vreg_s1i_0p9: smps1 { |
| 726 |
regulator-name = "vreg_s1i_0p9"; |
| 727 |
regulator-min-microvolt = <900000>; |
| 728 |
regulator-max-microvolt = <920000>; |
| 729 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 730 |
}; |
| 731 |
|
| 732 |
vreg_s2i_1p0: smps2 { |
| 733 |
regulator-name = "vreg_s2i_1p0"; |
| 734 |
regulator-min-microvolt = <1000000>; |
| 735 |
regulator-max-microvolt = <1100000>; |
| 736 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 737 |
}; |
| 738 |
|
| 739 |
vreg_l1i_1p8: ldo1 { |
| 740 |
regulator-name = "vreg_l1i_1p8"; |
| 741 |
regulator-min-microvolt = <1800000>; |
| 742 |
regulator-max-microvolt = <1800000>; |
| 743 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 744 |
}; |
| 745 |
|
| 746 |
vreg_l2i_1p2: ldo2 { |
| 747 |
regulator-name = "vreg_l2i_1p2"; |
| 748 |
regulator-min-microvolt = <1200000>; |
| 749 |
regulator-max-microvolt = <1200000>; |
| 750 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 751 |
}; |
| 752 |
|
| 753 |
vreg_l3i_0p8: ldo3 { |
| 754 |
regulator-name = "vreg_l3i_0p8"; |
| 755 |
regulator-min-microvolt = <880000>; |
| 756 |
regulator-max-microvolt = <920000>; |
| 757 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 758 |
}; |
| 759 |
}; |
| 760 |
|
| 761 |
regulators-7 { |
| 762 |
compatible = "qcom,pm8550ve-rpmh-regulators"; |
| 763 |
qcom,pmic-id = "j"; |
| 764 |
|
| 765 |
vdd-l1-supply = <&vreg_s1f_0p7>; |
| 766 |
vdd-l2-supply = <&vreg_s5j_1p2>; |
| 767 |
vdd-l3-supply = <&vreg_s1f_0p7>; |
| 768 |
vdd-s5-supply = <&vph_pwr>; |
| 769 |
|
| 770 |
vreg_s5j_1p2: smps5 { |
| 771 |
regulator-name = "vreg_s5j_1p2"; |
| 772 |
regulator-min-microvolt = <1256000>; |
| 773 |
regulator-max-microvolt = <1304000>; |
| 774 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 775 |
}; |
| 776 |
|
| 777 |
vreg_l1j_0p8: ldo1 { |
| 778 |
regulator-name = "vreg_l1j_0p8"; |
| 779 |
regulator-min-microvolt = <880000>; |
| 780 |
regulator-max-microvolt = <920000>; |
| 781 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 782 |
}; |
| 783 |
|
| 784 |
vreg_l2j_1p2: ldo2 { |
| 785 |
regulator-name = "vreg_l2j_1p2"; |
| 786 |
regulator-min-microvolt = <1256000>; |
| 787 |
regulator-max-microvolt = <1256000>; |
| 788 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 789 |
}; |
| 790 |
|
| 791 |
vreg_l3j_0p8: ldo3 { |
| 792 |
regulator-name = "vreg_l3j_0p8"; |
| 793 |
regulator-min-microvolt = <880000>; |
| 794 |
regulator-max-microvolt = <920000>; |
| 795 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 796 |
}; |
| 797 |
}; |
| 798 |
}; |
| 799 |
|
| 800 |
&gpu { |
| 801 |
status = "okay"; |
| 802 |
}; |
| 803 |
|
| 804 |
&gpu_zap_shader { |
| 805 |
firmware-name = "qcom/x1e80100/LENOVO/83ED/qcdxkmsuc8380.mbn"; |
| 806 |
}; |
| 807 |
|
| 808 |
&i2c0 { |
| 809 |
clock-frequency = <400000>; |
| 810 |
|
| 811 |
status = "okay"; |
| 812 |
|
| 813 |
touchpad@2c { |
| 814 |
compatible = "hid-over-i2c"; |
| 815 |
reg = <0x2c>; |
| 816 |
|
| 817 |
hid-descr-addr = <0x20>; |
| 818 |
interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>; |
| 819 |
|
| 820 |
pinctrl-0 = <&tpad_default>; |
| 821 |
pinctrl-names = "default"; |
| 822 |
|
| 823 |
wakeup-source; |
| 824 |
}; |
| 825 |
|
| 826 |
keyboard@3a { |
| 827 |
compatible = "hid-over-i2c"; |
| 828 |
reg = <0x3a>; |
| 829 |
|
| 830 |
hid-descr-addr = <0x1>; |
| 831 |
interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>; |
| 832 |
|
| 833 |
pinctrl-0 = <&kybd_default>; |
| 834 |
pinctrl-names = "default"; |
| 835 |
|
| 836 |
wakeup-source; |
| 837 |
}; |
| 838 |
}; |
| 839 |
|
| 840 |
&i2c1 { |
| 841 |
clock-frequency = <400000>; |
| 842 |
|
| 843 |
status = "okay"; |
| 844 |
|
| 845 |
typec-mux@8 { |
| 846 |
compatible = "parade,ps8830"; |
| 847 |
reg = <0x08>; |
| 848 |
|
| 849 |
clocks = <&rpmhcc RPMH_RF_CLK5>; |
| 850 |
|
| 851 |
vdd-supply = <&vreg_rtmr2_1p15>; |
| 852 |
vdd33-supply = <&vreg_rtmr2_3p3>; |
| 853 |
vdd33-cap-supply = <&vreg_rtmr2_3p3>; |
| 854 |
vddar-supply = <&vreg_rtmr2_1p15>; |
| 855 |
vddat-supply = <&vreg_rtmr2_1p15>; |
| 856 |
vddio-supply = <&vreg_rtmr2_1p8>; |
| 857 |
|
| 858 |
reset-gpios = <&tlmm 185 GPIO_ACTIVE_LOW>; |
| 859 |
|
| 860 |
pinctrl-0 = <&rtmr2_default>; |
| 861 |
pinctrl-names = "default"; |
| 862 |
|
| 863 |
orientation-switch; |
| 864 |
retimer-switch; |
| 865 |
|
| 866 |
ports { |
| 867 |
#address-cells = <1>; |
| 868 |
#size-cells = <0>; |
| 869 |
|
| 870 |
port@0 { |
| 871 |
reg = <0>; |
| 872 |
|
| 873 |
retimer_ss2_ss_out: endpoint { |
| 874 |
remote-endpoint = <&pmic_glink_ss2_ss_in>; |
| 875 |
}; |
| 876 |
}; |
| 877 |
|
| 878 |
port@1 { |
| 879 |
reg = <1>; |
| 880 |
|
| 881 |
retimer_ss2_ss_in: endpoint { |
| 882 |
remote-endpoint = <&usb_1_ss2_qmpphy_out>; |
| 883 |
}; |
| 884 |
}; |
| 885 |
|
| 886 |
port@2 { |
| 887 |
reg = <2>; |
| 888 |
|
| 889 |
retimer_ss2_con_sbu_out: endpoint { |
| 890 |
remote-endpoint = <&pmic_glink_ss2_con_sbu_in>; |
| 891 |
}; |
| 892 |
}; |
| 893 |
}; |
| 894 |
}; |
| 895 |
}; |
| 896 |
|
| 897 |
&i2c3 { |
| 898 |
clock-frequency = <400000>; |
| 899 |
|
| 900 |
status = "okay"; |
| 901 |
|
| 902 |
typec-mux@8 { |
| 903 |
compatible = "parade,ps8830"; |
| 904 |
reg = <0x08>; |
| 905 |
|
| 906 |
clocks = <&rpmhcc RPMH_RF_CLK3>; |
| 907 |
|
| 908 |
vdd-supply = <&vreg_rtmr0_1p15>; |
| 909 |
vdd33-supply = <&vreg_rtmr0_3p3>; |
| 910 |
vdd33-cap-supply = <&vreg_rtmr0_3p3>; |
| 911 |
vddar-supply = <&vreg_rtmr0_1p15>; |
| 912 |
vddat-supply = <&vreg_rtmr0_1p15>; |
| 913 |
vddio-supply = <&vreg_rtmr0_1p8>; |
| 914 |
|
| 915 |
reset-gpios = <&pm8550_gpios 10 GPIO_ACTIVE_LOW>; |
| 916 |
|
| 917 |
pinctrl-0 = <&rtmr0_default>; |
| 918 |
pinctrl-names = "default"; |
| 919 |
|
| 920 |
retimer-switch; |
| 921 |
orientation-switch; |
| 922 |
|
| 923 |
ports { |
| 924 |
#address-cells = <1>; |
| 925 |
#size-cells = <0>; |
| 926 |
|
| 927 |
port@0 { |
| 928 |
reg = <0>; |
| 929 |
|
| 930 |
retimer_ss0_ss_out: endpoint { |
| 931 |
remote-endpoint = <&pmic_glink_ss0_ss_in>; |
| 932 |
}; |
| 933 |
}; |
| 934 |
|
| 935 |
port@1 { |
| 936 |
reg = <1>; |
| 937 |
|
| 938 |
retimer_ss0_ss_in: endpoint { |
| 939 |
remote-endpoint = <&usb_1_ss0_qmpphy_out>; |
| 940 |
}; |
| 941 |
}; |
| 942 |
|
| 943 |
port@2 { |
| 944 |
reg = <2>; |
| 945 |
|
| 946 |
retimer_ss0_con_sbu_out: endpoint { |
| 947 |
remote-endpoint = <&pmic_glink_ss0_con_sbu_in>; |
| 948 |
}; |
| 949 |
}; |
| 950 |
}; |
| 951 |
}; |
| 952 |
}; |
| 953 |
|
| 954 |
&i2c7 { |
| 955 |
clock-frequency = <400000>; |
| 956 |
|
| 957 |
status = "okay"; |
| 958 |
|
| 959 |
typec-mux@8 { |
| 960 |
compatible = "parade,ps8830"; |
| 961 |
reg = <0x8>; |
| 962 |
|
| 963 |
clocks = <&rpmhcc RPMH_RF_CLK4>; |
| 964 |
|
| 965 |
vdd-supply = <&vreg_rtmr1_1p15>; |
| 966 |
vdd33-supply = <&vreg_rtmr1_3p3>; |
| 967 |
vdd33-cap-supply = <&vreg_rtmr1_3p3>; |
| 968 |
vddar-supply = <&vreg_rtmr1_1p15>; |
| 969 |
vddat-supply = <&vreg_rtmr1_1p15>; |
| 970 |
vddio-supply = <&vreg_rtmr1_1p8>; |
| 971 |
|
| 972 |
reset-gpios = <&tlmm 176 GPIO_ACTIVE_LOW>; |
| 973 |
|
| 974 |
pinctrl-0 = <&rtmr1_default>; |
| 975 |
pinctrl-names = "default"; |
| 976 |
|
| 977 |
retimer-switch; |
| 978 |
orientation-switch; |
| 979 |
|
| 980 |
ports { |
| 981 |
#address-cells = <1>; |
| 982 |
#size-cells = <0>; |
| 983 |
|
| 984 |
port@0 { |
| 985 |
reg = <0>; |
| 986 |
|
| 987 |
retimer_ss1_ss_out: endpoint { |
| 988 |
remote-endpoint = <&pmic_glink_ss1_ss_in>; |
| 989 |
}; |
| 990 |
}; |
| 991 |
|
| 992 |
port@1 { |
| 993 |
reg = <1>; |
| 994 |
|
| 995 |
retimer_ss1_ss_in: endpoint { |
| 996 |
remote-endpoint = <&usb_1_ss1_qmpphy_out>; |
| 997 |
}; |
| 998 |
}; |
| 999 |
|
| 1000 |
port@2 { |
| 1001 |
reg = <2>; |
| 1002 |
|
| 1003 |
retimer_ss1_con_sbu_out: endpoint { |
| 1004 |
remote-endpoint = <&pmic_glink_ss1_con_sbu_in>; |
| 1005 |
}; |
| 1006 |
}; |
| 1007 |
|
| 1008 |
}; |
| 1009 |
}; |
| 1010 |
}; |
| 1011 |
|
| 1012 |
&i2c8 { |
| 1013 |
clock-frequency = <400000>; |
| 1014 |
|
| 1015 |
status = "okay"; |
| 1016 |
|
| 1017 |
touchscreen@14 { |
| 1018 |
compatible = "hid-over-i2c"; |
| 1019 |
reg = <0x14>; |
| 1020 |
|
| 1021 |
hid-descr-addr = <0x1>; |
| 1022 |
interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>; |
| 1023 |
|
| 1024 |
pinctrl-0 = <&ts0_default>; |
| 1025 |
pinctrl-names = "default"; |
| 1026 |
}; |
| 1027 |
}; |
| 1028 |
|
| 1029 |
&iris { |
| 1030 |
firmware-name = "qcom/x1e80100/LENOVO/83ED/qcvss8380.mbn"; |
| 1031 |
status = "okay"; |
| 1032 |
}; |
| 1033 |
|
| 1034 |
&lpass_tlmm { |
| 1035 |
spkr_01_sd_n_active: spkr-01-sd-n-active-state { |
| 1036 |
pins = "gpio12"; |
| 1037 |
function = "gpio"; |
| 1038 |
drive-strength = <16>; |
| 1039 |
bias-disable; |
| 1040 |
output-low; |
| 1041 |
}; |
| 1042 |
|
| 1043 |
spkr_23_sd_n_active: spkr-23-sd-n-active-state { |
| 1044 |
pins = "gpio13"; |
| 1045 |
function = "gpio"; |
| 1046 |
drive-strength = <16>; |
| 1047 |
bias-disable; |
| 1048 |
output-low; |
| 1049 |
}; |
| 1050 |
}; |
| 1051 |
|
| 1052 |
&lpass_vamacro { |
| 1053 |
pinctrl-0 = <&dmic01_default>, <&dmic23_default>; |
| 1054 |
pinctrl-names = "default"; |
| 1055 |
|
| 1056 |
vdd-micb-supply = <&vreg_l1b_1p8>; |
| 1057 |
qcom,dmic-sample-rate = <4800000>; |
| 1058 |
}; |
| 1059 |
|
| 1060 |
&mdss { |
| 1061 |
status = "okay"; |
| 1062 |
}; |
| 1063 |
|
| 1064 |
&mdss_dp0 { |
| 1065 |
status = "okay"; |
| 1066 |
}; |
| 1067 |
|
| 1068 |
&mdss_dp0_out { |
| 1069 |
link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; |
| 1070 |
}; |
| 1071 |
|
| 1072 |
&mdss_dp1 { |
| 1073 |
status = "okay"; |
| 1074 |
}; |
| 1075 |
|
| 1076 |
&mdss_dp1_out { |
| 1077 |
link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; |
| 1078 |
}; |
| 1079 |
|
| 1080 |
&mdss_dp2 { |
| 1081 |
status = "okay"; |
| 1082 |
}; |
| 1083 |
|
| 1084 |
&mdss_dp2_out { |
| 1085 |
link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; |
| 1086 |
}; |
| 1087 |
|
| 1088 |
&mdss_dp3 { |
| 1089 |
/delete-property/ #sound-dai-cells; |
| 1090 |
|
| 1091 |
pinctrl-0 = <&edp0_hpd_default>; |
| 1092 |
pinctrl-names = "default"; |
| 1093 |
|
| 1094 |
status = "okay"; |
| 1095 |
|
| 1096 |
aux-bus { |
| 1097 |
panel { |
| 1098 |
compatible = "samsung,atna45dc02", "samsung,atna33xc20"; |
| 1099 |
enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>; |
| 1100 |
power-supply = <&vreg_edp_3p3>; |
| 1101 |
|
| 1102 |
pinctrl-0 = <&edp_bl_en>; |
| 1103 |
pinctrl-names = "default"; |
| 1104 |
|
| 1105 |
port { |
| 1106 |
edp_panel_in: endpoint { |
| 1107 |
remote-endpoint = <&mdss_dp3_out>; |
| 1108 |
}; |
| 1109 |
}; |
| 1110 |
}; |
| 1111 |
}; |
| 1112 |
}; |
| 1113 |
|
| 1114 |
&mdss_dp3_out { |
| 1115 |
data-lanes = <0 1 2 3>; |
| 1116 |
link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; |
| 1117 |
|
| 1118 |
remote-endpoint = <&edp_panel_in>; |
| 1119 |
}; |
| 1120 |
|
| 1121 |
&mdss_dp3_phy { |
| 1122 |
vdda-phy-supply = <&vreg_l3j_0p8>; |
| 1123 |
vdda-pll-supply = <&vreg_l2j_1p2>; |
| 1124 |
|
| 1125 |
status = "okay"; |
| 1126 |
}; |
| 1127 |
|
| 1128 |
&pcie4 { |
| 1129 |
pinctrl-0 = <&pcie4_default>; |
| 1130 |
pinctrl-names = "default"; |
| 1131 |
|
| 1132 |
status = "okay"; |
| 1133 |
}; |
| 1134 |
|
| 1135 |
&pcie4_phy { |
| 1136 |
vdda-phy-supply = <&vreg_l3i_0p8>; |
| 1137 |
vdda-pll-supply = <&vreg_l3e_1p2>; |
| 1138 |
|
| 1139 |
status = "okay"; |
| 1140 |
}; |
| 1141 |
|
| 1142 |
&pcie4_port0 { |
| 1143 |
reset-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>; |
| 1144 |
wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>; |
| 1145 |
|
| 1146 |
wifi@0 { |
| 1147 |
compatible = "pci17cb,1107"; |
| 1148 |
reg = <0x10000 0x0 0x0 0x0 0x0>; |
| 1149 |
|
| 1150 |
vddaon-supply = <&vreg_pmu_aon_0p59>; |
| 1151 |
vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; |
| 1152 |
vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; |
| 1153 |
vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; |
| 1154 |
vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; |
| 1155 |
vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; |
| 1156 |
vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>; |
| 1157 |
vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>; |
| 1158 |
vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>; |
| 1159 |
}; |
| 1160 |
}; |
| 1161 |
|
| 1162 |
&pcie6a { |
| 1163 |
vddpe-3v3-supply = <&vreg_nvme>; |
| 1164 |
|
| 1165 |
pinctrl-0 = <&pcie6a_default>; |
| 1166 |
pinctrl-names = "default"; |
| 1167 |
|
| 1168 |
status = "okay"; |
| 1169 |
}; |
| 1170 |
|
| 1171 |
&pcie6a_phy { |
| 1172 |
vdda-phy-supply = <&vreg_l1d_0p8>; |
| 1173 |
vdda-pll-supply = <&vreg_l2j_1p2>; |
| 1174 |
|
| 1175 |
status = "okay"; |
| 1176 |
}; |
| 1177 |
|
| 1178 |
&pcie6a_port0 { |
| 1179 |
reset-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>; |
| 1180 |
wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>; |
| 1181 |
}; |
| 1182 |
|
| 1183 |
&pm8550_gpios { |
| 1184 |
rtmr0_default: rtmr0-reset-n-active-state { |
| 1185 |
pins = "gpio10"; |
| 1186 |
function = "normal"; |
| 1187 |
power-source = <1>; /* 1.8V */ |
| 1188 |
bias-disable; |
| 1189 |
input-disable; |
| 1190 |
output-enable; |
| 1191 |
}; |
| 1192 |
|
| 1193 |
usb0_3p3_reg_en: usb0-3p3-reg-en-state { |
| 1194 |
pins = "gpio11"; |
| 1195 |
function = "normal"; |
| 1196 |
power-source = <1>; /* 1.8V */ |
| 1197 |
bias-disable; |
| 1198 |
input-disable; |
| 1199 |
output-enable; |
| 1200 |
}; |
| 1201 |
}; |
| 1202 |
|
| 1203 |
&pm8550ve_9_gpios { |
| 1204 |
usb0_1p8_reg_en: usb0-1p8-reg-en-state { |
| 1205 |
pins = "gpio8"; |
| 1206 |
function = "normal"; |
| 1207 |
power-source = <1>; /* 1.8V */ |
| 1208 |
bias-disable; |
| 1209 |
input-disable; |
| 1210 |
output-enable; |
| 1211 |
}; |
| 1212 |
}; |
| 1213 |
|
| 1214 |
&pmc8380_3_gpios { |
| 1215 |
edp_bl_en: edp-bl-en-state { |
| 1216 |
pins = "gpio4"; |
| 1217 |
function = "normal"; |
| 1218 |
power-source = <0>; |
| 1219 |
input-disable; |
| 1220 |
output-enable; |
| 1221 |
}; |
| 1222 |
}; |
| 1223 |
|
| 1224 |
&pmc8380_5_gpios { |
| 1225 |
usb0_pwr_1p15_reg_en: usb0-pwr-1p15-reg-en-state { |
| 1226 |
pins = "gpio8"; |
| 1227 |
function = "normal"; |
| 1228 |
power-source = <1>; /* 1.8V */ |
| 1229 |
bias-disable; |
| 1230 |
input-disable; |
| 1231 |
output-enable; |
| 1232 |
}; |
| 1233 |
}; |
| 1234 |
|
| 1235 |
&qupv3_0 { |
| 1236 |
status = "okay"; |
| 1237 |
}; |
| 1238 |
|
| 1239 |
&qupv3_1 { |
| 1240 |
status = "okay"; |
| 1241 |
}; |
| 1242 |
|
| 1243 |
&qupv3_2 { |
| 1244 |
status = "okay"; |
| 1245 |
}; |
| 1246 |
|
| 1247 |
&remoteproc_adsp { |
| 1248 |
firmware-name = "qcom/x1e80100/LENOVO/83ED/qcadsp8380.mbn", |
| 1249 |
"qcom/x1e80100/LENOVO/83ED/adsp_dtbs.elf"; |
| 1250 |
status = "okay"; |
| 1251 |
}; |
| 1252 |
|
| 1253 |
&remoteproc_cdsp { |
| 1254 |
firmware-name = "qcom/x1e80100/LENOVO/83ED/qccdsp8380.mbn", |
| 1255 |
"qcom/x1e80100/LENOVO/83ED/cdsp_dtbs.elf"; |
| 1256 |
|
| 1257 |
status = "okay"; |
| 1258 |
}; |
| 1259 |
|
| 1260 |
&smb2360_0 { |
| 1261 |
status = "okay"; |
| 1262 |
}; |
| 1263 |
|
| 1264 |
&smb2360_0_eusb2_repeater { |
| 1265 |
vdd18-supply = <&vreg_l3d_1p8>; |
| 1266 |
vdd3-supply = <&vreg_l2b_3p0>; |
| 1267 |
}; |
| 1268 |
|
| 1269 |
&smb2360_1 { |
| 1270 |
status = "okay"; |
| 1271 |
}; |
| 1272 |
|
| 1273 |
&smb2360_1_eusb2_repeater { |
| 1274 |
vdd18-supply = <&vreg_l3d_1p8>; |
| 1275 |
vdd3-supply = <&vreg_l14b_3p0>; |
| 1276 |
}; |
| 1277 |
|
| 1278 |
&smb2360_2 { |
| 1279 |
status = "okay"; |
| 1280 |
}; |
| 1281 |
|
| 1282 |
&smb2360_2_eusb2_repeater { |
| 1283 |
vdd18-supply = <&vreg_l3d_1p8>; |
| 1284 |
vdd3-supply = <&vreg_l8b_3p0>; |
| 1285 |
}; |
| 1286 |
|
| 1287 |
&swr0 { |
| 1288 |
status = "okay"; |
| 1289 |
|
| 1290 |
pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>; |
| 1291 |
pinctrl-names = "default"; |
| 1292 |
|
| 1293 |
/* WSA8845, Left Woofer */ |
| 1294 |
left_woofer: speaker@0,0 { |
| 1295 |
compatible = "sdw20217020400"; |
| 1296 |
reg = <0 0>; |
| 1297 |
reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>; |
| 1298 |
#sound-dai-cells = <0>; |
| 1299 |
sound-name-prefix = "WooferLeft"; |
| 1300 |
vdd-1p8-supply = <&vreg_l15b_1p8>; |
| 1301 |
vdd-io-supply = <&vreg_l12b_1p2>; |
| 1302 |
qcom,port-mapping = <1 2 3 7 10 13>; |
| 1303 |
}; |
| 1304 |
|
| 1305 |
/* WSA8845, Left Tweeter */ |
| 1306 |
left_tweeter: speaker@0,1 { |
| 1307 |
compatible = "sdw20217020400"; |
| 1308 |
reg = <0 1>; |
| 1309 |
reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>; |
| 1310 |
#sound-dai-cells = <0>; |
| 1311 |
sound-name-prefix = "TweeterLeft"; |
| 1312 |
vdd-1p8-supply = <&vreg_l15b_1p8>; |
| 1313 |
vdd-io-supply = <&vreg_l12b_1p2>; |
| 1314 |
qcom,port-mapping = <4 5 6 7 11 13>; |
| 1315 |
}; |
| 1316 |
}; |
| 1317 |
|
| 1318 |
|
| 1319 |
&swr3 { |
| 1320 |
status = "okay"; |
| 1321 |
|
| 1322 |
pinctrl-0 = <&wsa2_swr_active>, <&spkr_23_sd_n_active>; |
| 1323 |
pinctrl-names = "default"; |
| 1324 |
|
| 1325 |
/* WSA8845, Right Woofer */ |
| 1326 |
right_woofer: speaker@0,0 { |
| 1327 |
compatible = "sdw20217020400"; |
| 1328 |
reg = <0 0>; |
| 1329 |
reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>; |
| 1330 |
#sound-dai-cells = <0>; |
| 1331 |
sound-name-prefix = "WooferRight"; |
| 1332 |
vdd-1p8-supply = <&vreg_l15b_1p8>; |
| 1333 |
vdd-io-supply = <&vreg_l12b_1p2>; |
| 1334 |
qcom,port-mapping = <1 2 3 7 10 13>; |
| 1335 |
}; |
| 1336 |
|
| 1337 |
/* WSA8845, Right Tweeter */ |
| 1338 |
right_tweeter: speaker@0,1 { |
| 1339 |
compatible = "sdw20217020400"; |
| 1340 |
reg = <0 1>; |
| 1341 |
reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>; |
| 1342 |
#sound-dai-cells = <0>; |
| 1343 |
sound-name-prefix = "TweeterRight"; |
| 1344 |
vdd-1p8-supply = <&vreg_l15b_1p8>; |
| 1345 |
vdd-io-supply = <&vreg_l12b_1p2>; |
| 1346 |
qcom,port-mapping = <4 5 6 7 11 13>; |
| 1347 |
}; |
| 1348 |
}; |
| 1349 |
|
| 1350 |
&tlmm { |
| 1351 |
gpio-reserved-ranges = <34 2>, /* Unused */ |
| 1352 |
<44 4>, /* SPI (TPM) */ |
| 1353 |
<238 1>; /* UFS Reset */ |
| 1354 |
|
| 1355 |
edp_reg_en: edp-reg-en-state { |
| 1356 |
pins = "gpio70"; |
| 1357 |
function = "gpio"; |
| 1358 |
drive-strength = <16>; |
| 1359 |
bias-disable; |
| 1360 |
}; |
| 1361 |
|
| 1362 |
hall_int_n_default: hall-int-n-state { |
| 1363 |
lid-n-pins { |
| 1364 |
pins = "gpio92"; |
| 1365 |
function = "gpio"; |
| 1366 |
bias-disable; |
| 1367 |
}; |
| 1368 |
|
| 1369 |
/* |
| 1370 |
* Pins 71 and 92 seem to be bridged together (pin 71 and 92 show the same |
| 1371 |
* events). By default, pin 71 is set as output-high, which blocks any |
| 1372 |
* event on pin 92. Output-disable on pin 71 is necessary to get events on |
| 1373 |
* pin 92. |
| 1374 |
* The purpose of pin 71 is not yet known; lid-pull is a supposition. |
| 1375 |
*/ |
| 1376 |
lid-pull-n-pins { |
| 1377 |
pins = "gpio71"; |
| 1378 |
function = "gpio"; |
| 1379 |
bias-pull-up; |
| 1380 |
output-disable; |
| 1381 |
}; |
| 1382 |
}; |
| 1383 |
|
| 1384 |
kybd_default: kybd-default-state { |
| 1385 |
pins = "gpio67"; |
| 1386 |
function = "gpio"; |
| 1387 |
bias-disable; |
| 1388 |
}; |
| 1389 |
|
| 1390 |
nvme_reg_en: nvme-reg-en-state { |
| 1391 |
pins = "gpio18"; |
| 1392 |
function = "gpio"; |
| 1393 |
drive-strength = <2>; |
| 1394 |
bias-disable; |
| 1395 |
}; |
| 1396 |
|
| 1397 |
pcie4_default: pcie4-default-state { |
| 1398 |
clkreq-n-pins { |
| 1399 |
pins = "gpio147"; |
| 1400 |
function = "pcie4_clk"; |
| 1401 |
drive-strength = <2>; |
| 1402 |
bias-pull-up; |
| 1403 |
}; |
| 1404 |
|
| 1405 |
perst-n-pins { |
| 1406 |
pins = "gpio146"; |
| 1407 |
function = "gpio"; |
| 1408 |
drive-strength = <2>; |
| 1409 |
bias-disable; |
| 1410 |
}; |
| 1411 |
|
| 1412 |
wake-n-pins { |
| 1413 |
pins = "gpio148"; |
| 1414 |
function = "gpio"; |
| 1415 |
drive-strength = <2>; |
| 1416 |
bias-pull-up; |
| 1417 |
}; |
| 1418 |
}; |
| 1419 |
|
| 1420 |
pcie6a_default: pcie6a-default-state { |
| 1421 |
clkreq-n-pins { |
| 1422 |
pins = "gpio153"; |
| 1423 |
function = "pcie6a_clk"; |
| 1424 |
drive-strength = <2>; |
| 1425 |
bias-pull-up; |
| 1426 |
}; |
| 1427 |
|
| 1428 |
perst-n-pins { |
| 1429 |
pins = "gpio152"; |
| 1430 |
function = "gpio"; |
| 1431 |
drive-strength = <2>; |
| 1432 |
bias-disable; |
| 1433 |
}; |
| 1434 |
|
| 1435 |
wake-n-pins { |
| 1436 |
pins = "gpio154"; |
| 1437 |
function = "gpio"; |
| 1438 |
drive-strength = <2>; |
| 1439 |
bias-pull-up; |
| 1440 |
}; |
| 1441 |
}; |
| 1442 |
|
| 1443 |
rtmr1_default: rtmr1-reset-n-active-state { |
| 1444 |
pins = "gpio176"; |
| 1445 |
function = "gpio"; |
| 1446 |
drive-strength = <2>; |
| 1447 |
bias-disable; |
| 1448 |
}; |
| 1449 |
|
| 1450 |
rtmr2_default: rtmr2-reset-n-active-state { |
| 1451 |
pins = "gpio185"; |
| 1452 |
function = "gpio"; |
| 1453 |
drive-strength = <2>; |
| 1454 |
bias-disable; |
| 1455 |
}; |
| 1456 |
|
| 1457 |
tpad_default: tpad-default-state { |
| 1458 |
pins = "gpio3"; |
| 1459 |
function = "gpio"; |
| 1460 |
bias-disable; |
| 1461 |
}; |
| 1462 |
|
| 1463 |
ts0_default: ts0-default-state { |
| 1464 |
int-n-pins { |
| 1465 |
pins = "gpio51"; |
| 1466 |
function = "gpio"; |
| 1467 |
bias-disable; |
| 1468 |
}; |
| 1469 |
|
| 1470 |
reset-n-pins { |
| 1471 |
pins = "gpio48"; |
| 1472 |
function = "gpio"; |
| 1473 |
output-high; |
| 1474 |
drive-strength = <16>; |
| 1475 |
}; |
| 1476 |
}; |
| 1477 |
|
| 1478 |
usb1_pwr_1p15_reg_en: usb1-pwr-1p15-reg-en-state { |
| 1479 |
pins = "gpio188"; |
| 1480 |
function = "gpio"; |
| 1481 |
drive-strength = <2>; |
| 1482 |
bias-disable; |
| 1483 |
}; |
| 1484 |
|
| 1485 |
usb1_pwr_1p8_reg_en: usb1-pwr-1p8-reg-en-state { |
| 1486 |
pins = "gpio175"; |
| 1487 |
function = "gpio"; |
| 1488 |
drive-strength = <2>; |
| 1489 |
bias-disable; |
| 1490 |
}; |
| 1491 |
|
| 1492 |
usb1_pwr_3p3_reg_en: usb1-pwr-3p3-reg-en-state { |
| 1493 |
pins = "gpio186"; |
| 1494 |
function = "gpio"; |
| 1495 |
drive-strength = <2>; |
| 1496 |
bias-disable; |
| 1497 |
}; |
| 1498 |
|
| 1499 |
usb2_pwr_1p15_reg_en: usb2-pwr-1p15-reg-en-state { |
| 1500 |
pins = "gpio189"; |
| 1501 |
function = "gpio"; |
| 1502 |
drive-strength = <2>; |
| 1503 |
bias-disable; |
| 1504 |
}; |
| 1505 |
|
| 1506 |
usb2_pwr_1p8_reg_en: usb2-pwr-1p8-reg-en-state { |
| 1507 |
pins = "gpio126"; |
| 1508 |
function = "gpio"; |
| 1509 |
drive-strength = <2>; |
| 1510 |
bias-disable; |
| 1511 |
}; |
| 1512 |
|
| 1513 |
usb2_pwr_3p3_reg_en: usb2-pwr-3p3-reg-en-state { |
| 1514 |
pins = "gpio187"; |
| 1515 |
function = "gpio"; |
| 1516 |
drive-strength = <2>; |
| 1517 |
bias-disable; |
| 1518 |
}; |
| 1519 |
|
| 1520 |
wcn_sw_en: wcn-sw-en-state { |
| 1521 |
pins = "gpio214"; |
| 1522 |
function = "gpio"; |
| 1523 |
drive-strength = <2>; |
| 1524 |
bias-disable; |
| 1525 |
}; |
| 1526 |
|
| 1527 |
wcn_wlan_bt_en: wcn-wlan-bt-en-state { |
| 1528 |
pins = "gpio116", "gpio117"; |
| 1529 |
function = "gpio"; |
| 1530 |
drive-strength = <2>; |
| 1531 |
bias-disable; |
| 1532 |
}; |
| 1533 |
}; |
| 1534 |
|
| 1535 |
&uart14 { |
| 1536 |
status = "okay"; |
| 1537 |
|
| 1538 |
bluetooth { |
| 1539 |
compatible = "qcom,wcn7850-bt"; |
| 1540 |
max-speed = <3200000>; |
| 1541 |
|
| 1542 |
vddaon-supply = <&vreg_pmu_aon_0p59>; |
| 1543 |
vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; |
| 1544 |
vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; |
| 1545 |
vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; |
| 1546 |
vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; |
| 1547 |
vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; |
| 1548 |
vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>; |
| 1549 |
}; |
| 1550 |
}; |
| 1551 |
|
| 1552 |
&uart21 { |
| 1553 |
compatible = "qcom,geni-debug-uart"; |
| 1554 |
status = "okay"; |
| 1555 |
}; |
| 1556 |
|
| 1557 |
&usb_1_ss0_hsphy { |
| 1558 |
vdd-supply = <&vreg_l3j_0p8>; |
| 1559 |
vdda12-supply = <&vreg_l2j_1p2>; |
| 1560 |
|
| 1561 |
phys = <&smb2360_0_eusb2_repeater>; |
| 1562 |
|
| 1563 |
status = "okay"; |
| 1564 |
}; |
| 1565 |
|
| 1566 |
&usb_1_ss0_qmpphy { |
| 1567 |
vdda-phy-supply = <&vreg_l2j_1p2>; |
| 1568 |
vdda-pll-supply = <&vreg_l1j_0p8>; |
| 1569 |
|
| 1570 |
status = "okay"; |
| 1571 |
}; |
| 1572 |
|
| 1573 |
&usb_1_ss0 { |
| 1574 |
status = "okay"; |
| 1575 |
}; |
| 1576 |
|
| 1577 |
&usb_1_ss0_dwc3 { |
| 1578 |
dr_mode = "host"; |
| 1579 |
}; |
| 1580 |
|
| 1581 |
&usb_1_ss0_dwc3_hs { |
| 1582 |
remote-endpoint = <&pmic_glink_ss0_hs_in>; |
| 1583 |
}; |
| 1584 |
|
| 1585 |
&usb_1_ss0_qmpphy_out { |
| 1586 |
remote-endpoint = <&retimer_ss0_ss_in>; |
| 1587 |
}; |
| 1588 |
|
| 1589 |
&usb_1_ss1_hsphy { |
| 1590 |
vdd-supply = <&vreg_l3j_0p8>; |
| 1591 |
vdda12-supply = <&vreg_l2j_1p2>; |
| 1592 |
|
| 1593 |
phys = <&smb2360_1_eusb2_repeater>; |
| 1594 |
|
| 1595 |
status = "okay"; |
| 1596 |
}; |
| 1597 |
|
| 1598 |
&usb_1_ss1_qmpphy { |
| 1599 |
vdda-phy-supply = <&vreg_l2j_1p2>; |
| 1600 |
vdda-pll-supply = <&vreg_l2d_0p9>; |
| 1601 |
|
| 1602 |
status = "okay"; |
| 1603 |
}; |
| 1604 |
|
| 1605 |
&usb_1_ss1 { |
| 1606 |
status = "okay"; |
| 1607 |
}; |
| 1608 |
|
| 1609 |
&usb_1_ss1_dwc3 { |
| 1610 |
dr_mode = "host"; |
| 1611 |
}; |
| 1612 |
|
| 1613 |
&usb_1_ss1_dwc3_hs { |
| 1614 |
remote-endpoint = <&pmic_glink_ss1_hs_in>; |
| 1615 |
}; |
| 1616 |
|
| 1617 |
&usb_1_ss1_qmpphy_out { |
| 1618 |
remote-endpoint = <&retimer_ss1_ss_in>; |
| 1619 |
}; |
| 1620 |
|
| 1621 |
&usb_1_ss2_hsphy { |
| 1622 |
vdd-supply = <&vreg_l3j_0p8>; |
| 1623 |
vdda12-supply = <&vreg_l2j_1p2>; |
| 1624 |
|
| 1625 |
phys = <&smb2360_2_eusb2_repeater>; |
| 1626 |
|
| 1627 |
status = "okay"; |
| 1628 |
}; |
| 1629 |
|
| 1630 |
&usb_1_ss2_qmpphy { |
| 1631 |
vdda-phy-supply = <&vreg_l2j_1p2>; |
| 1632 |
vdda-pll-supply = <&vreg_l2d_0p9>; |
| 1633 |
|
| 1634 |
status = "okay"; |
| 1635 |
}; |
| 1636 |
|
| 1637 |
&usb_1_ss2 { |
| 1638 |
status = "okay"; |
| 1639 |
}; |
| 1640 |
|
| 1641 |
&usb_1_ss2_dwc3 { |
| 1642 |
dr_mode = "host"; |
| 1643 |
}; |
| 1644 |
|
| 1645 |
&usb_1_ss2_dwc3_hs { |
| 1646 |
remote-endpoint = <&pmic_glink_ss2_hs_in>; |
| 1647 |
}; |
| 1648 |
|
| 1649 |
&usb_1_ss2_qmpphy_out { |
| 1650 |
remote-endpoint = <&retimer_ss2_ss_in>; |
| 1651 |
}; |