| 1 |
// SPDX-License-Identifier: BSD-3-Clause |
| 2 |
/* |
| 3 |
* Copyright (c) 2021, Luca Weiss <[email protected]> |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
|
| 8 |
/* PM7250B is configured to use SID2/3 */ |
| 9 |
#define PM7250B_SID 2 |
| 10 |
#define PM7250B_SID1 3 |
| 11 |
|
| 12 |
/* PMK8350 (in reality a PMK8003) is configured to use SID6 instead of 0 */ |
| 13 |
#define PMK8350_SID 6 |
| 14 |
|
| 15 |
#include <dt-bindings/firmware/qcom,scm.h> |
| 16 |
#include <dt-bindings/gpio/gpio.h> |
| 17 |
#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h> |
| 18 |
#include <dt-bindings/input/input.h> |
| 19 |
#include <dt-bindings/leds/common.h> |
| 20 |
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| 21 |
#include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| 22 |
#include <dt-bindings/sound/qcom,q6asm.h> |
| 23 |
#include <dt-bindings/usb/pd.h> |
| 24 |
#include "sm7225.dtsi" |
| 25 |
#include "pm6150l.dtsi" |
| 26 |
#include "pm6350.dtsi" |
| 27 |
#include "pm7250b.dtsi" |
| 28 |
#include "pmk8350.dtsi" |
| 29 |
|
| 30 |
/ { |
| 31 |
model = "Fairphone 4"; |
| 32 |
compatible = "fairphone,fp4", "qcom,sm7225"; |
| 33 |
chassis-type = "handset"; |
| 34 |
|
| 35 |
/* required for bootloader to select correct board */ |
| 36 |
qcom,msm-id = <459 0x10000>; |
| 37 |
qcom,board-id = <8 32>; |
| 38 |
|
| 39 |
aliases { |
| 40 |
serial0 = &uart9; |
| 41 |
serial1 = &uart1; |
| 42 |
}; |
| 43 |
|
| 44 |
chosen { |
| 45 |
#address-cells = <2>; |
| 46 |
#size-cells = <2>; |
| 47 |
ranges; |
| 48 |
|
| 49 |
stdout-path = "serial0:115200n8"; |
| 50 |
|
| 51 |
framebuffer0: framebuffer@a000000 { |
| 52 |
compatible = "simple-framebuffer"; |
| 53 |
reg = <0 0xa0000000 0 (2340 * 1080 * 4)>; |
| 54 |
width = <1080>; |
| 55 |
height = <2340>; |
| 56 |
stride = <(1080 * 4)>; |
| 57 |
format = "a8r8g8b8"; |
| 58 |
}; |
| 59 |
}; |
| 60 |
|
| 61 |
gpio-keys { |
| 62 |
compatible = "gpio-keys"; |
| 63 |
pinctrl-names = "default"; |
| 64 |
pinctrl-0 = <&gpio_keys_pin>; |
| 65 |
|
| 66 |
key-volume-up { |
| 67 |
label = "volume_up"; |
| 68 |
linux,code = <KEY_VOLUMEUP>; |
| 69 |
gpios = <&pm6350_gpios 2 GPIO_ACTIVE_LOW>; |
| 70 |
}; |
| 71 |
}; |
| 72 |
|
| 73 |
/* Dummy regulator until PM6150L has LCDB VSP/VSN support */ |
| 74 |
lcdb_dummy: regulator-lcdb-dummy { |
| 75 |
compatible = "regulator-fixed"; |
| 76 |
regulator-name = "lcdb_dummy"; |
| 77 |
regulator-min-microvolt = <5500000>; |
| 78 |
regulator-max-microvolt = <5500000>; |
| 79 |
}; |
| 80 |
|
| 81 |
reserved-memory { |
| 82 |
/* |
| 83 |
* The rmtfs memory region in downstream is 'dynamically allocated' |
| 84 |
* but given the same address every time. Hard code it as this address is |
| 85 |
* where the modem firmware expects it to be. |
| 86 |
*/ |
| 87 |
memory@efe01000 { |
| 88 |
compatible = "qcom,rmtfs-mem"; |
| 89 |
reg = <0 0xefe01000 0 0x600000>; |
| 90 |
no-map; |
| 91 |
|
| 92 |
qcom,client-id = <1>; |
| 93 |
qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>; |
| 94 |
}; |
| 95 |
}; |
| 96 |
|
| 97 |
msm_therm_sensor: thermal-sensor-msm { |
| 98 |
compatible = "generic-adc-thermal"; |
| 99 |
#thermal-sensor-cells = <0>; |
| 100 |
io-channels = <&pm6150l_adc ADC5_AMUX_THM2_100K_PU>; |
| 101 |
io-channel-names = "sensor-channel"; |
| 102 |
}; |
| 103 |
|
| 104 |
rear_cam_sensor: thermal-sensor-rear-cam { |
| 105 |
compatible = "generic-adc-thermal"; |
| 106 |
#thermal-sensor-cells = <0>; |
| 107 |
io-channels = <&pm6150l_adc ADC5_GPIO2_100K_PU>; |
| 108 |
io-channel-names = "sensor-channel"; |
| 109 |
}; |
| 110 |
|
| 111 |
thermal-zones { |
| 112 |
chg-skin-thermal { |
| 113 |
thermal-sensors = <&pm7250b_adc_tm 0>; |
| 114 |
|
| 115 |
trips { |
| 116 |
active-config0 { |
| 117 |
temperature = <125000>; |
| 118 |
hysteresis = <1000>; |
| 119 |
type = "passive"; |
| 120 |
}; |
| 121 |
}; |
| 122 |
}; |
| 123 |
|
| 124 |
conn-thermal { |
| 125 |
thermal-sensors = <&pm7250b_adc_tm 1>; |
| 126 |
|
| 127 |
trips { |
| 128 |
active-config0 { |
| 129 |
temperature = <125000>; |
| 130 |
hysteresis = <1000>; |
| 131 |
type = "passive"; |
| 132 |
}; |
| 133 |
}; |
| 134 |
}; |
| 135 |
|
| 136 |
pa0-thermal { |
| 137 |
thermal-sensors = <&pm6150l_adc_tm 1>; |
| 138 |
|
| 139 |
trips { |
| 140 |
active-config0 { |
| 141 |
temperature = <125000>; |
| 142 |
hysteresis = <1000>; |
| 143 |
type = "passive"; |
| 144 |
}; |
| 145 |
}; |
| 146 |
}; |
| 147 |
|
| 148 |
pa1-thermal { |
| 149 |
thermal-sensors = <&pm6150l_adc_tm 0>; |
| 150 |
|
| 151 |
trips { |
| 152 |
active-config0 { |
| 153 |
temperature = <125000>; |
| 154 |
hysteresis = <1000>; |
| 155 |
type = "passive"; |
| 156 |
}; |
| 157 |
}; |
| 158 |
}; |
| 159 |
|
| 160 |
pm8008-thermal { |
| 161 |
polling-delay-passive = <100>; |
| 162 |
thermal-sensors = <&pm8008>; |
| 163 |
|
| 164 |
trips { |
| 165 |
trip0 { |
| 166 |
temperature = <95000>; |
| 167 |
hysteresis = <0>; |
| 168 |
type = "passive"; |
| 169 |
}; |
| 170 |
|
| 171 |
trip1 { |
| 172 |
temperature = <115000>; |
| 173 |
hysteresis = <0>; |
| 174 |
type = "critical"; |
| 175 |
}; |
| 176 |
}; |
| 177 |
}; |
| 178 |
|
| 179 |
quiet-thermal { |
| 180 |
thermal-sensors = <&pm6150l_adc_tm 3>; |
| 181 |
|
| 182 |
trips { |
| 183 |
active-config0 { |
| 184 |
temperature = <125000>; |
| 185 |
hysteresis = <1000>; |
| 186 |
type = "passive"; |
| 187 |
}; |
| 188 |
}; |
| 189 |
}; |
| 190 |
|
| 191 |
rear-cam-thermal { |
| 192 |
polling-delay-passive = <1000>; |
| 193 |
polling-delay = <5000>; |
| 194 |
thermal-sensors = <&rear_cam_sensor>; |
| 195 |
|
| 196 |
trips { |
| 197 |
active-config0 { |
| 198 |
temperature = <125000>; |
| 199 |
hysteresis = <1000>; |
| 200 |
type = "passive"; |
| 201 |
}; |
| 202 |
}; |
| 203 |
}; |
| 204 |
|
| 205 |
rfc-flash-thermal { |
| 206 |
thermal-sensors = <&pm6150l_adc_tm 2>; |
| 207 |
|
| 208 |
trips { |
| 209 |
active-config0 { |
| 210 |
temperature = <125000>; |
| 211 |
hysteresis = <1000>; |
| 212 |
type = "passive"; |
| 213 |
}; |
| 214 |
}; |
| 215 |
}; |
| 216 |
|
| 217 |
sdm-skin-thermal { |
| 218 |
polling-delay-passive = <1000>; |
| 219 |
polling-delay = <5000>; |
| 220 |
thermal-sensors = <&msm_therm_sensor>; |
| 221 |
|
| 222 |
trips { |
| 223 |
trip0 { |
| 224 |
temperature = <45000>; |
| 225 |
hysteresis = <0>; |
| 226 |
type = "passive"; |
| 227 |
}; |
| 228 |
|
| 229 |
trip1 { |
| 230 |
temperature = <55000>; |
| 231 |
hysteresis = <0>; |
| 232 |
type = "critical"; |
| 233 |
}; |
| 234 |
}; |
| 235 |
}; |
| 236 |
|
| 237 |
xo-thermal { |
| 238 |
thermal-sensors = <&pmk8350_adc_tm 0>; |
| 239 |
|
| 240 |
trips { |
| 241 |
active-config0 { |
| 242 |
temperature = <125000>; |
| 243 |
hysteresis = <1000>; |
| 244 |
type = "passive"; |
| 245 |
}; |
| 246 |
}; |
| 247 |
}; |
| 248 |
}; |
| 249 |
|
| 250 |
vreg_32m_cam_dvdd_1p05: regulator-32m-cam-dvdd-1p05 { |
| 251 |
compatible = "regulator-fixed"; |
| 252 |
regulator-name = "32M_CAM_DVDD_1P05"; |
| 253 |
regulator-min-microvolt = <1050000>; |
| 254 |
regulator-max-microvolt = <1050000>; |
| 255 |
gpio = <&pm6150l_gpios 2 GPIO_ACTIVE_HIGH>; |
| 256 |
enable-active-high; |
| 257 |
vin-supply = <&vreg_s8e>; |
| 258 |
}; |
| 259 |
|
| 260 |
vreg_48m_ois_avdd0_1p8: regulator-48m-ois-avdd0-1p8 { |
| 261 |
compatible = "regulator-fixed"; |
| 262 |
regulator-name = "48M_OIS_AVDD0_1P8"; |
| 263 |
regulator-min-microvolt = <1800000>; |
| 264 |
regulator-max-microvolt = <1800000>; |
| 265 |
gpio = <&pm6150l_gpios 4 GPIO_ACTIVE_HIGH>; |
| 266 |
enable-active-high; |
| 267 |
vin-supply = <&vreg_bob>; |
| 268 |
}; |
| 269 |
|
| 270 |
vreg_48m_uw_avdd0_1p8: regulator-48m-uw-avdd0-1p8 { |
| 271 |
compatible = "regulator-fixed"; |
| 272 |
regulator-name = "48M_UW_AVDD0_1P8"; |
| 273 |
regulator-min-microvolt = <1800000>; |
| 274 |
regulator-max-microvolt = <1800000>; |
| 275 |
gpio = <&pm6150l_gpios 3 GPIO_ACTIVE_HIGH>; |
| 276 |
enable-active-high; |
| 277 |
vin-supply = <&vreg_bob>; |
| 278 |
}; |
| 279 |
|
| 280 |
vreg_ois_2p8: regulator-ois-2p8 { |
| 281 |
compatible = "regulator-fixed"; |
| 282 |
regulator-name = "OIS_2P8"; |
| 283 |
regulator-min-microvolt = <2800000>; |
| 284 |
regulator-max-microvolt = <2800000>; |
| 285 |
gpio = <&tlmm 72 GPIO_ACTIVE_HIGH>; |
| 286 |
enable-active-high; |
| 287 |
vin-supply = <&vreg_bob>; |
| 288 |
}; |
| 289 |
}; |
| 290 |
|
| 291 |
&adsp { |
| 292 |
firmware-name = "qcom/sm7225/fairphone4/adsp.mbn"; |
| 293 |
status = "okay"; |
| 294 |
}; |
| 295 |
|
| 296 |
&apps_rsc { |
| 297 |
regulators-0 { |
| 298 |
compatible = "qcom,pm6350-rpmh-regulators"; |
| 299 |
qcom,pmic-id = "a"; |
| 300 |
|
| 301 |
vreg_s1a: smps1 { |
| 302 |
regulator-name = "vreg_s1a"; |
| 303 |
regulator-min-microvolt = <1000000>; |
| 304 |
regulator-max-microvolt = <1200000>; |
| 305 |
}; |
| 306 |
|
| 307 |
vreg_s2a: smps2 { |
| 308 |
regulator-name = "vreg_s2a"; |
| 309 |
regulator-min-microvolt = <1503000>; |
| 310 |
regulator-max-microvolt = <2048000>; |
| 311 |
}; |
| 312 |
|
| 313 |
vreg_l2a: ldo2 { |
| 314 |
regulator-name = "vreg_l2a"; |
| 315 |
regulator-min-microvolt = <1503000>; |
| 316 |
regulator-max-microvolt = <1980000>; |
| 317 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 318 |
}; |
| 319 |
|
| 320 |
vreg_l3a: ldo3 { |
| 321 |
regulator-name = "vreg_l3a"; |
| 322 |
regulator-min-microvolt = <2700000>; |
| 323 |
regulator-max-microvolt = <3300000>; |
| 324 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 325 |
}; |
| 326 |
|
| 327 |
vreg_l4a: ldo4 { |
| 328 |
regulator-name = "vreg_l4a"; |
| 329 |
regulator-min-microvolt = <352000>; |
| 330 |
regulator-max-microvolt = <801000>; |
| 331 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 332 |
}; |
| 333 |
|
| 334 |
vreg_l5a: ldo5 { |
| 335 |
regulator-name = "vreg_l5a"; |
| 336 |
regulator-min-microvolt = <1503000>; |
| 337 |
regulator-max-microvolt = <1980000>; |
| 338 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 339 |
}; |
| 340 |
|
| 341 |
vreg_l6a: ldo6 { |
| 342 |
regulator-name = "vreg_l6a"; |
| 343 |
regulator-min-microvolt = <1710000>; |
| 344 |
regulator-max-microvolt = <3544000>; |
| 345 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 346 |
}; |
| 347 |
|
| 348 |
vreg_l7a: ldo7 { |
| 349 |
regulator-name = "vreg_l7a"; |
| 350 |
regulator-min-microvolt = <1620000>; |
| 351 |
regulator-max-microvolt = <1980000>; |
| 352 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 353 |
}; |
| 354 |
|
| 355 |
vreg_l8a: ldo8 { |
| 356 |
regulator-name = "vreg_l8a"; |
| 357 |
regulator-min-microvolt = <2800000>; |
| 358 |
regulator-max-microvolt = <2800000>; |
| 359 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 360 |
}; |
| 361 |
|
| 362 |
vreg_l9a: ldo9 { |
| 363 |
regulator-name = "vreg_l9a"; |
| 364 |
regulator-min-microvolt = <1650000>; |
| 365 |
regulator-max-microvolt = <3401000>; |
| 366 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 367 |
}; |
| 368 |
|
| 369 |
vreg_l11a: ldo11 { |
| 370 |
regulator-name = "vreg_l11a"; |
| 371 |
regulator-min-microvolt = <1800000>; |
| 372 |
regulator-max-microvolt = <2000000>; |
| 373 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 374 |
}; |
| 375 |
|
| 376 |
vreg_l12a: ldo12 { |
| 377 |
regulator-name = "vreg_l12a"; |
| 378 |
regulator-min-microvolt = <1620000>; |
| 379 |
regulator-max-microvolt = <1980000>; |
| 380 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 381 |
}; |
| 382 |
|
| 383 |
vreg_l13a: ldo13 { |
| 384 |
regulator-name = "vreg_l13a"; |
| 385 |
regulator-min-microvolt = <570000>; |
| 386 |
regulator-max-microvolt = <650000>; |
| 387 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 388 |
}; |
| 389 |
|
| 390 |
vreg_l14a: ldo14 { |
| 391 |
regulator-name = "vreg_l14a"; |
| 392 |
regulator-min-microvolt = <1700000>; |
| 393 |
regulator-max-microvolt = <1900000>; |
| 394 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 395 |
}; |
| 396 |
|
| 397 |
vreg_l15a: ldo15 { |
| 398 |
regulator-name = "vreg_l15a"; |
| 399 |
regulator-min-microvolt = <1100000>; |
| 400 |
regulator-max-microvolt = <1305000>; |
| 401 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 402 |
}; |
| 403 |
|
| 404 |
vreg_l16a: ldo16 { |
| 405 |
regulator-name = "vreg_l16a"; |
| 406 |
regulator-min-microvolt = <830000>; |
| 407 |
regulator-max-microvolt = <921000>; |
| 408 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 409 |
}; |
| 410 |
|
| 411 |
vreg_l18a: ldo18 { |
| 412 |
regulator-name = "vreg_l18a"; |
| 413 |
regulator-min-microvolt = <788000>; |
| 414 |
regulator-max-microvolt = <1049000>; |
| 415 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 416 |
}; |
| 417 |
|
| 418 |
vreg_l19a: ldo19 { |
| 419 |
regulator-name = "vreg_l19a"; |
| 420 |
regulator-min-microvolt = <1080000>; |
| 421 |
regulator-max-microvolt = <1305000>; |
| 422 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 423 |
}; |
| 424 |
|
| 425 |
vreg_l20a: ldo20 { |
| 426 |
regulator-name = "vreg_l20a"; |
| 427 |
regulator-min-microvolt = <530000>; |
| 428 |
regulator-max-microvolt = <801000>; |
| 429 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 430 |
}; |
| 431 |
|
| 432 |
vreg_l21a: ldo21 { |
| 433 |
regulator-name = "vreg_l21a"; |
| 434 |
regulator-min-microvolt = <751000>; |
| 435 |
regulator-max-microvolt = <825000>; |
| 436 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 437 |
}; |
| 438 |
|
| 439 |
vreg_l22a: ldo22 { |
| 440 |
regulator-name = "vreg_l22a"; |
| 441 |
regulator-min-microvolt = <1080000>; |
| 442 |
regulator-max-microvolt = <1305000>; |
| 443 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 444 |
}; |
| 445 |
}; |
| 446 |
|
| 447 |
regulators-1 { |
| 448 |
compatible = "qcom,pm6150l-rpmh-regulators"; |
| 449 |
qcom,pmic-id = "e"; |
| 450 |
|
| 451 |
vreg_s8e: smps8 { |
| 452 |
regulator-name = "vreg_s8e"; |
| 453 |
regulator-min-microvolt = <313000>; |
| 454 |
regulator-max-microvolt = <1395000>; |
| 455 |
}; |
| 456 |
|
| 457 |
vreg_l1e: ldo1 { |
| 458 |
regulator-name = "vreg_l1e"; |
| 459 |
regulator-min-microvolt = <1620000>; |
| 460 |
regulator-max-microvolt = <1980000>; |
| 461 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 462 |
}; |
| 463 |
|
| 464 |
vreg_l2e: ldo2 { |
| 465 |
regulator-name = "vreg_l2e"; |
| 466 |
regulator-min-microvolt = <1170000>; |
| 467 |
regulator-max-microvolt = <1305000>; |
| 468 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 469 |
}; |
| 470 |
|
| 471 |
vreg_l3e: ldo3 { |
| 472 |
regulator-name = "vreg_l3e"; |
| 473 |
regulator-min-microvolt = <1100000>; |
| 474 |
regulator-max-microvolt = <1299000>; |
| 475 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 476 |
}; |
| 477 |
|
| 478 |
vreg_l4e: ldo4 { |
| 479 |
regulator-name = "vreg_l4e"; |
| 480 |
regulator-min-microvolt = <1620000>; |
| 481 |
regulator-max-microvolt = <3300000>; |
| 482 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 483 |
}; |
| 484 |
|
| 485 |
vreg_l5e: ldo5 { |
| 486 |
regulator-name = "vreg_l5e"; |
| 487 |
regulator-min-microvolt = <1620000>; |
| 488 |
regulator-max-microvolt = <3300000>; |
| 489 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 490 |
}; |
| 491 |
|
| 492 |
vreg_l6e: ldo6 { |
| 493 |
regulator-name = "vreg_l6e"; |
| 494 |
regulator-min-microvolt = <1700000>; |
| 495 |
regulator-max-microvolt = <2950000>; |
| 496 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 497 |
regulator-allow-set-load; |
| 498 |
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| 499 |
RPMH_REGULATOR_MODE_HPM>; |
| 500 |
}; |
| 501 |
|
| 502 |
vreg_l7e: ldo7 { |
| 503 |
regulator-name = "vreg_l7e"; |
| 504 |
regulator-min-microvolt = <2700000>; |
| 505 |
regulator-max-microvolt = <3544000>; |
| 506 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 507 |
}; |
| 508 |
|
| 509 |
vreg_l8e: ldo8 { |
| 510 |
regulator-name = "vreg_l8e"; |
| 511 |
regulator-min-microvolt = <1620000>; |
| 512 |
regulator-max-microvolt = <2000000>; |
| 513 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 514 |
}; |
| 515 |
|
| 516 |
vreg_l9e: ldo9 { |
| 517 |
regulator-name = "vreg_l9e"; |
| 518 |
regulator-min-microvolt = <2700000>; |
| 519 |
regulator-max-microvolt = <2960000>; |
| 520 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 521 |
regulator-allow-set-load; |
| 522 |
regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM |
| 523 |
RPMH_REGULATOR_MODE_HPM>; |
| 524 |
}; |
| 525 |
|
| 526 |
vreg_l10e: ldo10 { |
| 527 |
regulator-name = "vreg_l10e"; |
| 528 |
regulator-min-microvolt = <3000000>; |
| 529 |
regulator-max-microvolt = <3401000>; |
| 530 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 531 |
}; |
| 532 |
|
| 533 |
vreg_l11e: ldo11 { |
| 534 |
regulator-name = "vreg_l11e"; |
| 535 |
regulator-min-microvolt = <3000000>; |
| 536 |
regulator-max-microvolt = <3401000>; |
| 537 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 538 |
}; |
| 539 |
|
| 540 |
vreg_bob: bob { |
| 541 |
regulator-name = "vreg_bob"; |
| 542 |
regulator-min-microvolt = <1620000>; |
| 543 |
regulator-max-microvolt = <5492000>; |
| 544 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; |
| 545 |
regulator-allow-bypass; |
| 546 |
}; |
| 547 |
}; |
| 548 |
}; |
| 549 |
|
| 550 |
&cci0 { |
| 551 |
status = "okay"; |
| 552 |
}; |
| 553 |
|
| 554 |
&cci0_i2c0 { |
| 555 |
/* Main cam (Sony IMX582) @ 0x1a */ |
| 556 |
/* VCM driver (Onsemi LC898219XI) @ 0x28 */ |
| 557 |
/* OIS driver (CML CM401) @ 0x30 */ |
| 558 |
|
| 559 |
eeprom@50 { |
| 560 |
compatible = "giantec,gt24p128e", "atmel,24c128"; |
| 561 |
reg = <0x50>; |
| 562 |
vcc-supply = <&vreg_l6p>; |
| 563 |
read-only; |
| 564 |
}; |
| 565 |
}; |
| 566 |
|
| 567 |
&cci0_i2c1 { |
| 568 |
/* VCM driver (Dongwoon DW9800W) @ 0xc */ |
| 569 |
/* Ultra-wide cam (Sony IMX582) @ 0x1a */ |
| 570 |
|
| 571 |
eeprom@50 { |
| 572 |
compatible = "giantec,gt24p64a", "atmel,24c64"; |
| 573 |
reg = <0x50>; |
| 574 |
vcc-supply = <&vreg_l6p>; |
| 575 |
read-only; |
| 576 |
}; |
| 577 |
}; |
| 578 |
|
| 579 |
&cci1 { |
| 580 |
status = "okay"; |
| 581 |
}; |
| 582 |
|
| 583 |
&cci1_i2c0 { |
| 584 |
/* Front cam (Sony IMX576) @ 0x10 */ |
| 585 |
|
| 586 |
eeprom@50 { |
| 587 |
compatible = "giantec,gt24p64a", "atmel,24c64"; |
| 588 |
reg = <0x50>; |
| 589 |
vcc-supply = <&vreg_l6p>; |
| 590 |
read-only; |
| 591 |
}; |
| 592 |
}; |
| 593 |
|
| 594 |
&cdsp { |
| 595 |
firmware-name = "qcom/sm7225/fairphone4/cdsp.mbn"; |
| 596 |
status = "okay"; |
| 597 |
}; |
| 598 |
|
| 599 |
&gpi_dma0 { |
| 600 |
status = "okay"; |
| 601 |
}; |
| 602 |
|
| 603 |
&gpi_dma1 { |
| 604 |
status = "okay"; |
| 605 |
}; |
| 606 |
|
| 607 |
&gpu { |
| 608 |
status = "okay"; |
| 609 |
}; |
| 610 |
|
| 611 |
&gpu_zap_shader { |
| 612 |
firmware-name = "qcom/sm7225/fairphone4/a615_zap.mbn"; |
| 613 |
}; |
| 614 |
|
| 615 |
&i2c0 { |
| 616 |
clock-frequency = <400000>; |
| 617 |
status = "okay"; |
| 618 |
|
| 619 |
/* ST21NFCD NFC @ 8 */ |
| 620 |
/* VL53L3 ToF @ 29 */ |
| 621 |
/* AW88264A amplifier @ 34 */ |
| 622 |
/* AW88264A amplifier @ 35 */ |
| 623 |
}; |
| 624 |
|
| 625 |
&i2c8 { |
| 626 |
clock-frequency = <400000>; |
| 627 |
status = "okay"; |
| 628 |
|
| 629 |
/* HX83112A touchscreen @ 48 */ |
| 630 |
}; |
| 631 |
|
| 632 |
&i2c10 { |
| 633 |
clock-frequency = <400000>; |
| 634 |
status = "okay"; |
| 635 |
|
| 636 |
pm8008: pmic@8 { |
| 637 |
compatible = "qcom,pm8008"; |
| 638 |
reg = <0x8>; |
| 639 |
|
| 640 |
interrupts-extended = <&tlmm 59 IRQ_TYPE_EDGE_RISING>; |
| 641 |
reset-gpios = <&tlmm 58 GPIO_ACTIVE_LOW>; |
| 642 |
|
| 643 |
vdd-l1-l2-supply = <&vreg_s8e>; |
| 644 |
vdd-l3-l4-supply = <&vreg_bob>; |
| 645 |
vdd-l5-supply = <&vreg_bob>; |
| 646 |
vdd-l6-supply = <&vreg_s2a>; |
| 647 |
vdd-l7-supply = <&vreg_bob>; |
| 648 |
|
| 649 |
pinctrl-names = "default"; |
| 650 |
pinctrl-0 = <&pm8008_default>; |
| 651 |
|
| 652 |
gpio-controller; |
| 653 |
#gpio-cells = <2>; |
| 654 |
gpio-ranges = <&pm8008 0 0 2>; |
| 655 |
|
| 656 |
interrupt-controller; |
| 657 |
#interrupt-cells = <2>; |
| 658 |
|
| 659 |
#thermal-sensor-cells = <0>; |
| 660 |
|
| 661 |
regulators { |
| 662 |
vreg_l1p: ldo1 { |
| 663 |
regulator-name = "vreg_l1p"; |
| 664 |
regulator-min-microvolt = <528000>; |
| 665 |
regulator-max-microvolt = <1200000>; |
| 666 |
}; |
| 667 |
|
| 668 |
vreg_l2p: ldo2 { |
| 669 |
regulator-name = "vreg_l2p"; |
| 670 |
regulator-min-microvolt = <528000>; |
| 671 |
regulator-max-microvolt = <1200000>; |
| 672 |
}; |
| 673 |
|
| 674 |
vreg_l3p: ldo3 { |
| 675 |
regulator-name = "vreg_l3p"; |
| 676 |
regulator-min-microvolt = <1500000>; |
| 677 |
regulator-max-microvolt = <2800000>; |
| 678 |
}; |
| 679 |
|
| 680 |
vreg_l4p: ldo4 { |
| 681 |
regulator-name = "vreg_l4p"; |
| 682 |
regulator-min-microvolt = <1500000>; |
| 683 |
regulator-max-microvolt = <2904000>; |
| 684 |
}; |
| 685 |
|
| 686 |
vreg_l5p: ldo5 { |
| 687 |
regulator-name = "vreg_l5p"; |
| 688 |
regulator-min-microvolt = <1500000>; |
| 689 |
regulator-max-microvolt = <2900000>; |
| 690 |
}; |
| 691 |
|
| 692 |
vreg_l6p: ldo6 { |
| 693 |
regulator-name = "vreg_l6p"; |
| 694 |
regulator-min-microvolt = <1500000>; |
| 695 |
regulator-max-microvolt = <1800000>; |
| 696 |
/* Pull-up for CCI I2C busses */ |
| 697 |
regulator-always-on; |
| 698 |
}; |
| 699 |
|
| 700 |
vreg_l7p: ldo7 { |
| 701 |
regulator-name = "vreg_l7p"; |
| 702 |
regulator-min-microvolt = <1500000>; |
| 703 |
regulator-max-microvolt = <3140000>; |
| 704 |
}; |
| 705 |
}; |
| 706 |
}; |
| 707 |
|
| 708 |
/* PX8618 @ 26 */ |
| 709 |
/* SMB1395 PMIC @ 34 */ |
| 710 |
/* awinic,aw8695 @ 5a */ |
| 711 |
}; |
| 712 |
|
| 713 |
&ipa { |
| 714 |
qcom,gsi-loader = "self"; |
| 715 |
memory-region = <&pil_ipa_fw_mem>; |
| 716 |
firmware-name = "qcom/sm7225/fairphone4/ipa_fws.mbn"; |
| 717 |
status = "okay"; |
| 718 |
}; |
| 719 |
|
| 720 |
&mdss { |
| 721 |
status = "okay"; |
| 722 |
}; |
| 723 |
|
| 724 |
&mdss_dsi0 { |
| 725 |
vdda-supply = <&vreg_l22a>; |
| 726 |
status = "okay"; |
| 727 |
|
| 728 |
panel@0 { |
| 729 |
compatible = "djn,9a-3r063-1102b"; |
| 730 |
reg = <0>; |
| 731 |
|
| 732 |
backlight = <&pm6150l_wled>; |
| 733 |
reset-gpios = <&pm6150l_gpios 9 GPIO_ACTIVE_LOW>; |
| 734 |
|
| 735 |
vdd1-supply = <&vreg_l1e>; |
| 736 |
vsn-supply = <&lcdb_dummy>; |
| 737 |
vsp-supply = <&lcdb_dummy>; |
| 738 |
|
| 739 |
port { |
| 740 |
panel_in: endpoint { |
| 741 |
remote-endpoint = <&mdss_dsi0_out>; |
| 742 |
}; |
| 743 |
}; |
| 744 |
}; |
| 745 |
}; |
| 746 |
|
| 747 |
&mdss_dsi0_out { |
| 748 |
data-lanes = <0 1 2 3>; |
| 749 |
remote-endpoint = <&panel_in>; |
| 750 |
}; |
| 751 |
|
| 752 |
&mdss_dsi0_phy { |
| 753 |
vdds-supply = <&vreg_l18a>; |
| 754 |
status = "okay"; |
| 755 |
}; |
| 756 |
|
| 757 |
&mpss { |
| 758 |
firmware-name = "qcom/sm7225/fairphone4/modem.mbn"; |
| 759 |
status = "okay"; |
| 760 |
}; |
| 761 |
|
| 762 |
&pm6150l_adc { |
| 763 |
pinctrl-0 = <&pm6150l_adc_default>; |
| 764 |
pinctrl-names = "default"; |
| 765 |
|
| 766 |
channel@4d { |
| 767 |
reg = <ADC5_AMUX_THM1_100K_PU>; |
| 768 |
label = "pa_therm1"; |
| 769 |
qcom,hw-settle-time = <200>; |
| 770 |
qcom,pre-scaling = <1 1>; |
| 771 |
qcom,ratiometric; |
| 772 |
}; |
| 773 |
|
| 774 |
channel@4e { |
| 775 |
reg = <ADC5_AMUX_THM2_100K_PU>; |
| 776 |
label = "msm_therm"; |
| 777 |
qcom,hw-settle-time = <200>; |
| 778 |
qcom,pre-scaling = <1 1>; |
| 779 |
qcom,ratiometric; |
| 780 |
}; |
| 781 |
|
| 782 |
channel@4f { |
| 783 |
reg = <ADC5_AMUX_THM3_100K_PU>; |
| 784 |
label = "pa_therm0"; |
| 785 |
qcom,hw-settle-time = <200>; |
| 786 |
qcom,pre-scaling = <1 1>; |
| 787 |
qcom,ratiometric; |
| 788 |
}; |
| 789 |
|
| 790 |
channel@53 { |
| 791 |
reg = <ADC5_GPIO2_100K_PU>; |
| 792 |
label = "rear_cam_therm"; |
| 793 |
qcom,hw-settle-time = <200>; |
| 794 |
qcom,pre-scaling = <1 1>; |
| 795 |
qcom,ratiometric; |
| 796 |
}; |
| 797 |
|
| 798 |
channel@54 { |
| 799 |
reg = <ADC5_GPIO3_100K_PU>; |
| 800 |
label = "rear_cam_flash_therm"; |
| 801 |
qcom,hw-settle-time = <200>; |
| 802 |
qcom,pre-scaling = <1 1>; |
| 803 |
qcom,ratiometric; |
| 804 |
}; |
| 805 |
|
| 806 |
channel@55 { |
| 807 |
reg = <ADC5_GPIO4_100K_PU>; |
| 808 |
label = "quiet_therm"; |
| 809 |
qcom,hw-settle-time = <200>; |
| 810 |
qcom,pre-scaling = <1 1>; |
| 811 |
qcom,ratiometric; |
| 812 |
}; |
| 813 |
}; |
| 814 |
|
| 815 |
&pm6150l_adc_tm { |
| 816 |
status = "okay"; |
| 817 |
|
| 818 |
pa-therm1@0 { |
| 819 |
reg = <0>; |
| 820 |
io-channels = <&pm6150l_adc ADC5_AMUX_THM1_100K_PU>; |
| 821 |
qcom,hw-settle-time-us = <200>; |
| 822 |
qcom,ratiometric; |
| 823 |
}; |
| 824 |
|
| 825 |
pa-therm0@1 { |
| 826 |
reg = <1>; |
| 827 |
io-channels = <&pm6150l_adc ADC5_AMUX_THM3_100K_PU>; |
| 828 |
qcom,hw-settle-time-us = <200>; |
| 829 |
qcom,ratiometric; |
| 830 |
}; |
| 831 |
|
| 832 |
rear-cam-flash-therm@2 { |
| 833 |
reg = <2>; |
| 834 |
io-channels = <&pm6150l_adc ADC5_GPIO3_100K_PU>; |
| 835 |
qcom,hw-settle-time-us = <200>; |
| 836 |
qcom,ratiometric; |
| 837 |
}; |
| 838 |
|
| 839 |
quiet-therm@3 { |
| 840 |
reg = <3>; |
| 841 |
io-channels = <&pm6150l_adc ADC5_GPIO4_100K_PU>; |
| 842 |
qcom,hw-settle-time-us = <200>; |
| 843 |
qcom,ratiometric; |
| 844 |
}; |
| 845 |
}; |
| 846 |
|
| 847 |
&pm6150l_flash { |
| 848 |
status = "okay"; |
| 849 |
|
| 850 |
led-0 { |
| 851 |
function = LED_FUNCTION_FLASH; |
| 852 |
color = <LED_COLOR_ID_YELLOW>; |
| 853 |
led-sources = <1>; |
| 854 |
led-max-microamp = <180000>; |
| 855 |
flash-max-microamp = <1000000>; |
| 856 |
flash-max-timeout-us = <1280000>; |
| 857 |
}; |
| 858 |
|
| 859 |
led-1 { |
| 860 |
function = LED_FUNCTION_FLASH; |
| 861 |
color = <LED_COLOR_ID_WHITE>; |
| 862 |
led-sources = <2>; |
| 863 |
led-max-microamp = <180000>; |
| 864 |
flash-max-microamp = <1000000>; |
| 865 |
flash-max-timeout-us = <1280000>; |
| 866 |
}; |
| 867 |
}; |
| 868 |
|
| 869 |
&pm6150l_gpios { |
| 870 |
pm6150l_adc_default: adc-default-state { |
| 871 |
pins = "gpio6", "gpio7", "gpio10"; |
| 872 |
function = PMIC_GPIO_FUNC_NORMAL; |
| 873 |
bias-high-impedance; |
| 874 |
}; |
| 875 |
}; |
| 876 |
|
| 877 |
&pm6150l_wled { |
| 878 |
qcom,switching-freq = <800>; |
| 879 |
qcom,current-limit-microamp = <20000>; |
| 880 |
qcom,num-strings = <2>; |
| 881 |
|
| 882 |
status = "okay"; |
| 883 |
}; |
| 884 |
|
| 885 |
&pm6350_gpios { |
| 886 |
gpio_keys_pin: gpio-keys-state { |
| 887 |
pins = "gpio2"; |
| 888 |
function = PMIC_GPIO_FUNC_NORMAL; |
| 889 |
bias-pull-up; |
| 890 |
input-enable; |
| 891 |
power-source = <0>; |
| 892 |
}; |
| 893 |
}; |
| 894 |
|
| 895 |
&pm6350_resin { |
| 896 |
linux,code = <KEY_VOLUMEDOWN>; |
| 897 |
status = "okay"; |
| 898 |
}; |
| 899 |
|
| 900 |
&pm7250b_adc { |
| 901 |
channel@4d { |
| 902 |
reg = <ADC5_AMUX_THM1_100K_PU>; |
| 903 |
qcom,ratiometric; |
| 904 |
qcom,hw-settle-time = <200>; |
| 905 |
qcom,pre-scaling = <1 1>; |
| 906 |
label = "charger_skin_therm"; |
| 907 |
}; |
| 908 |
|
| 909 |
channel@4f { |
| 910 |
reg = <ADC5_AMUX_THM3_100K_PU>; |
| 911 |
qcom,ratiometric; |
| 912 |
qcom,hw-settle-time = <200>; |
| 913 |
qcom,pre-scaling = <1 1>; |
| 914 |
label = "conn_therm"; |
| 915 |
}; |
| 916 |
}; |
| 917 |
|
| 918 |
&pm7250b_adc_tm { |
| 919 |
status = "okay"; |
| 920 |
|
| 921 |
charger-skin-therm@0 { |
| 922 |
reg = <0>; |
| 923 |
io-channels = <&pm7250b_adc ADC5_AMUX_THM1_100K_PU>; |
| 924 |
qcom,ratiometric; |
| 925 |
qcom,hw-settle-time-us = <200>; |
| 926 |
}; |
| 927 |
|
| 928 |
conn-therm@1 { |
| 929 |
reg = <1>; |
| 930 |
io-channels = <&pm7250b_adc ADC5_AMUX_THM3_100K_PU>; |
| 931 |
qcom,ratiometric; |
| 932 |
qcom,hw-settle-time-us = <200>; |
| 933 |
}; |
| 934 |
}; |
| 935 |
|
| 936 |
&pm7250b_typec { |
| 937 |
vdd-pdphy-supply = <&vreg_l3a>; |
| 938 |
|
| 939 |
status = "okay"; |
| 940 |
|
| 941 |
connector { |
| 942 |
compatible = "usb-c-connector"; |
| 943 |
|
| 944 |
power-role = "dual"; |
| 945 |
data-role = "dual"; |
| 946 |
self-powered; |
| 947 |
|
| 948 |
/* |
| 949 |
* Disable USB Power Delivery for now, seems to need extra work |
| 950 |
* to support role switching while also letting the battery |
| 951 |
* charge still - without charger driver |
| 952 |
*/ |
| 953 |
typec-power-opmode = "default"; |
| 954 |
pd-disable; |
| 955 |
|
| 956 |
ports { |
| 957 |
#address-cells = <1>; |
| 958 |
#size-cells = <0>; |
| 959 |
|
| 960 |
port@0 { |
| 961 |
reg = <0>; |
| 962 |
pm7250b_hs_in: endpoint { |
| 963 |
remote-endpoint = <&usb_1_dwc3_hs_out>; |
| 964 |
}; |
| 965 |
}; |
| 966 |
|
| 967 |
port@1 { |
| 968 |
reg = <1>; |
| 969 |
pm7250b_ss_in: endpoint { |
| 970 |
remote-endpoint = <&usb_1_qmpphy_out>; |
| 971 |
}; |
| 972 |
}; |
| 973 |
}; |
| 974 |
}; |
| 975 |
}; |
| 976 |
|
| 977 |
&pm7250b_vbus { |
| 978 |
regulator-min-microamp = <500000>; |
| 979 |
regulator-max-microamp = <1500000>; |
| 980 |
status = "okay"; |
| 981 |
}; |
| 982 |
|
| 983 |
&pmk8350_adc_tm { |
| 984 |
status = "okay"; |
| 985 |
|
| 986 |
xo-therm@0 { |
| 987 |
reg = <0>; |
| 988 |
io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>; |
| 989 |
qcom,hw-settle-time-us = <200>; |
| 990 |
qcom,ratiometric; |
| 991 |
}; |
| 992 |
}; |
| 993 |
|
| 994 |
&pmk8350_rtc { |
| 995 |
status = "okay"; |
| 996 |
}; |
| 997 |
|
| 998 |
&pmk8350_vadc { |
| 999 |
channel@644 { |
| 1000 |
reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>; |
| 1001 |
qcom,ratiometric; |
| 1002 |
qcom,hw-settle-time = <200>; |
| 1003 |
qcom,pre-scaling = <1 1>; |
| 1004 |
label = "xo_therm"; |
| 1005 |
}; |
| 1006 |
}; |
| 1007 |
|
| 1008 |
&q6asmdai { |
| 1009 |
dai@0 { |
| 1010 |
reg = <MSM_FRONTEND_DAI_MULTIMEDIA1>; |
| 1011 |
}; |
| 1012 |
}; |
| 1013 |
|
| 1014 |
&qup_uart1_cts { |
| 1015 |
/* |
| 1016 |
* Configure a bias-bus-hold on CTS to lower power |
| 1017 |
* usage when Bluetooth is turned off. Bus hold will |
| 1018 |
* maintain a low power state regardless of whether |
| 1019 |
* the Bluetooth module drives the pin in either |
| 1020 |
* direction or leaves the pin fully unpowered. |
| 1021 |
*/ |
| 1022 |
bias-bus-hold; |
| 1023 |
}; |
| 1024 |
|
| 1025 |
&qup_uart1_rts { |
| 1026 |
/* We'll drive RTS, so no pull */ |
| 1027 |
drive-strength = <2>; |
| 1028 |
bias-disable; |
| 1029 |
}; |
| 1030 |
|
| 1031 |
&qup_uart1_rx { |
| 1032 |
/* |
| 1033 |
* Configure a pull-up on RX. This is needed to avoid |
| 1034 |
* garbage data when the TX pin of the Bluetooth module is |
| 1035 |
* in tri-state (module powered off or not driving the |
| 1036 |
* signal yet). |
| 1037 |
*/ |
| 1038 |
bias-pull-up; |
| 1039 |
}; |
| 1040 |
|
| 1041 |
&qup_uart1_tx { |
| 1042 |
/* We'll drive TX, so no pull */ |
| 1043 |
drive-strength = <2>; |
| 1044 |
bias-disable; |
| 1045 |
}; |
| 1046 |
|
| 1047 |
&qupv3_id_0 { |
| 1048 |
status = "okay"; |
| 1049 |
}; |
| 1050 |
|
| 1051 |
&qupv3_id_1 { |
| 1052 |
status = "okay"; |
| 1053 |
}; |
| 1054 |
|
| 1055 |
&sdc2_off_state { |
| 1056 |
sd-cd-pins { |
| 1057 |
pins = "gpio94"; |
| 1058 |
function = "gpio"; |
| 1059 |
drive-strength = <2>; |
| 1060 |
bias-disable; |
| 1061 |
}; |
| 1062 |
}; |
| 1063 |
|
| 1064 |
&sdc2_on_state { |
| 1065 |
sd-cd-pins { |
| 1066 |
pins = "gpio94"; |
| 1067 |
function = "gpio"; |
| 1068 |
drive-strength = <2>; |
| 1069 |
bias-pull-up; |
| 1070 |
}; |
| 1071 |
}; |
| 1072 |
|
| 1073 |
&sdhc_2 { |
| 1074 |
vmmc-supply = <&vreg_l9e>; |
| 1075 |
vqmmc-supply = <&vreg_l6e>; |
| 1076 |
|
| 1077 |
cd-gpios = <&tlmm 94 GPIO_ACTIVE_LOW>; |
| 1078 |
|
| 1079 |
status = "okay"; |
| 1080 |
}; |
| 1081 |
|
| 1082 |
&sound { |
| 1083 |
compatible = "fairphone,fp4-sndcard"; |
| 1084 |
model = "Fairphone 4"; |
| 1085 |
|
| 1086 |
mm1-dai-link { |
| 1087 |
link-name = "MultiMedia1"; |
| 1088 |
|
| 1089 |
cpu { |
| 1090 |
sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>; |
| 1091 |
}; |
| 1092 |
}; |
| 1093 |
|
| 1094 |
usb-dai-link { |
| 1095 |
link-name = "USB Playback"; |
| 1096 |
|
| 1097 |
codec { |
| 1098 |
sound-dai = <&q6usbdai USB_RX>; |
| 1099 |
}; |
| 1100 |
|
| 1101 |
cpu { |
| 1102 |
sound-dai = <&q6afedai USB_RX>; |
| 1103 |
}; |
| 1104 |
|
| 1105 |
platform { |
| 1106 |
sound-dai = <&q6routing>; |
| 1107 |
}; |
| 1108 |
}; |
| 1109 |
}; |
| 1110 |
|
| 1111 |
&tlmm { |
| 1112 |
gpio-reserved-ranges = <13 4>, <56 2>; |
| 1113 |
|
| 1114 |
qup_uart1_sleep_cts: qup-uart1-sleep-cts-state { |
| 1115 |
pins = "gpio61"; |
| 1116 |
function = "gpio"; |
| 1117 |
/* |
| 1118 |
* Configure a bias-bus-hold on CTS to lower power |
| 1119 |
* usage when Bluetooth is turned off. Bus hold will |
| 1120 |
* maintain a low power state regardless of whether |
| 1121 |
* the Bluetooth module drives the pin in either |
| 1122 |
* direction or leaves the pin fully unpowered. |
| 1123 |
*/ |
| 1124 |
bias-bus-hold; |
| 1125 |
}; |
| 1126 |
|
| 1127 |
qup_uart1_sleep_rts: qup-uart1-sleep-rts-state { |
| 1128 |
pins = "gpio62"; |
| 1129 |
function = "gpio"; |
| 1130 |
/* |
| 1131 |
* Configure pull-down on RTS. As RTS is active low |
| 1132 |
* signal, pull it low to indicate the BT SoC that it |
| 1133 |
* can wakeup the system anytime from suspend state by |
| 1134 |
* pulling RX low (by sending wakeup bytes). |
| 1135 |
*/ |
| 1136 |
bias-pull-down; |
| 1137 |
}; |
| 1138 |
|
| 1139 |
qup_uart1_sleep_rx: qup-uart1-sleep-rx-state { |
| 1140 |
pins = "gpio64"; |
| 1141 |
function = "gpio"; |
| 1142 |
/* |
| 1143 |
* Configure a pull-up on RX. This is needed to avoid |
| 1144 |
* garbage data when the TX pin of the Bluetooth module |
| 1145 |
* is floating which may cause spurious wakeups. |
| 1146 |
*/ |
| 1147 |
bias-pull-up; |
| 1148 |
}; |
| 1149 |
|
| 1150 |
qup_uart1_sleep_tx: qup-uart1-sleep-tx-state { |
| 1151 |
pins = "gpio63"; |
| 1152 |
function = "gpio"; |
| 1153 |
/* |
| 1154 |
* Configure pull-up on TX when it isn't actively driven |
| 1155 |
* to prevent BT SoC from receiving garbage during sleep. |
| 1156 |
*/ |
| 1157 |
bias-pull-up; |
| 1158 |
}; |
| 1159 |
|
| 1160 |
pm8008_default: pm8008-default-state { |
| 1161 |
int-pins { |
| 1162 |
pins = "gpio59"; |
| 1163 |
function = "gpio"; |
| 1164 |
drive-strength = <2>; |
| 1165 |
bias-pull-down; |
| 1166 |
}; |
| 1167 |
|
| 1168 |
reset-n-pins { |
| 1169 |
pins = "gpio58"; |
| 1170 |
function = "gpio"; |
| 1171 |
drive-strength = <2>; |
| 1172 |
bias-disable; |
| 1173 |
}; |
| 1174 |
}; |
| 1175 |
}; |
| 1176 |
|
| 1177 |
&uart1 { |
| 1178 |
/delete-property/ interrupts; |
| 1179 |
interrupts-extended = <&intc GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>, |
| 1180 |
<&tlmm 64 IRQ_TYPE_EDGE_FALLING>; |
| 1181 |
|
| 1182 |
pinctrl-names = "default", "sleep"; |
| 1183 |
pinctrl-1 = <&qup_uart1_sleep_cts>, <&qup_uart1_sleep_rts>, <&qup_uart1_sleep_tx>, <&qup_uart1_sleep_rx>; |
| 1184 |
|
| 1185 |
status = "okay"; |
| 1186 |
|
| 1187 |
bluetooth { |
| 1188 |
compatible = "qcom,wcn3988-bt"; |
| 1189 |
|
| 1190 |
vddio-supply = <&vreg_l11a>; |
| 1191 |
vddxo-supply = <&vreg_l7a>; |
| 1192 |
vddrf-supply = <&vreg_l2e>; |
| 1193 |
vddch0-supply = <&vreg_l10e>; |
| 1194 |
swctrl-gpios = <&tlmm 69 GPIO_ACTIVE_HIGH>; |
| 1195 |
|
| 1196 |
max-speed = <3200000>; |
| 1197 |
}; |
| 1198 |
}; |
| 1199 |
|
| 1200 |
&uart9 { |
| 1201 |
status = "okay"; |
| 1202 |
}; |
| 1203 |
|
| 1204 |
&ufs_mem_hc { |
| 1205 |
reset-gpios = <&tlmm 156 GPIO_ACTIVE_LOW>; |
| 1206 |
|
| 1207 |
vcc-supply = <&vreg_l7e>; |
| 1208 |
vcc-max-microamp = <800000>; |
| 1209 |
vccq2-supply = <&vreg_l12a>; |
| 1210 |
vccq2-max-microamp = <800000>; |
| 1211 |
|
| 1212 |
status = "okay"; |
| 1213 |
}; |
| 1214 |
|
| 1215 |
&ufs_mem_phy { |
| 1216 |
vdda-phy-supply = <&vreg_l18a>; |
| 1217 |
vdda-pll-supply = <&vreg_l22a>; |
| 1218 |
|
| 1219 |
status = "okay"; |
| 1220 |
}; |
| 1221 |
|
| 1222 |
&usb_1 { |
| 1223 |
status = "okay"; |
| 1224 |
}; |
| 1225 |
|
| 1226 |
&usb_1_dwc3 { |
| 1227 |
maximum-speed = "super-speed"; |
| 1228 |
dr_mode = "otg"; |
| 1229 |
}; |
| 1230 |
|
| 1231 |
&usb_1_dwc3_hs_out { |
| 1232 |
remote-endpoint = <&pm7250b_hs_in>; |
| 1233 |
}; |
| 1234 |
|
| 1235 |
&usb_1_hsphy { |
| 1236 |
vdd-supply = <&vreg_l18a>; |
| 1237 |
vdda-pll-supply = <&vreg_l2a>; |
| 1238 |
vdda-phy-dpdm-supply = <&vreg_l3a>; |
| 1239 |
|
| 1240 |
status = "okay"; |
| 1241 |
}; |
| 1242 |
|
| 1243 |
&usb_1_qmpphy { |
| 1244 |
vdda-phy-supply = <&vreg_l22a>; |
| 1245 |
vdda-pll-supply = <&vreg_l16a>; |
| 1246 |
|
| 1247 |
status = "okay"; |
| 1248 |
}; |
| 1249 |
|
| 1250 |
&usb_1_qmpphy_out { |
| 1251 |
remote-endpoint = <&pm7250b_ss_in>; |
| 1252 |
}; |
| 1253 |
|
| 1254 |
&wifi { |
| 1255 |
vdd-0.8-cx-mx-supply = <&vreg_l4a>; |
| 1256 |
vdd-1.8-xo-supply = <&vreg_l7a>; |
| 1257 |
vdd-1.3-rfa-supply = <&vreg_l2e>; |
| 1258 |
vdd-3.3-ch0-supply = <&vreg_l10e>; |
| 1259 |
vdd-3.3-ch1-supply = <&vreg_l11e>; |
| 1260 |
|
| 1261 |
status = "okay"; |
| 1262 |
}; |