| 1 |
// SPDX-License-Identifier: BSD-3-Clause |
| 2 |
/* |
| 3 |
* Copyright (c) 2020, Konrad Dybcio <[email protected]> |
| 4 |
* Copyright (c) 2020, AngeloGioacchino Del Regno |
| 5 |
* <[email protected]> |
| 6 |
*/ |
| 7 |
|
| 8 |
#include "pm660.dtsi" |
| 9 |
#include "pm660l.dtsi" |
| 10 |
#include <dt-bindings/gpio/gpio.h> |
| 11 |
#include <dt-bindings/input/input.h> |
| 12 |
#include <dt-bindings/input/gpio-keys.h> |
| 13 |
#include <dt-bindings/leds/common.h> |
| 14 |
|
| 15 |
/ { |
| 16 |
/* required for bootloader to select correct board */ |
| 17 |
qcom,msm-id = <318 0>; |
| 18 |
qcom,board-id = <8 1>; |
| 19 |
qcom,pmic-id = <0x1001b 0x101011a 0x00 0x00 0x1001b 0x201011a 0x00 0x00>; |
| 20 |
|
| 21 |
/* This part enables graphical output via bootloader-enabled display */ |
| 22 |
chosen { |
| 23 |
bootargs = "earlycon=tty0 console=tty0"; |
| 24 |
|
| 25 |
#address-cells = <2>; |
| 26 |
#size-cells = <2>; |
| 27 |
ranges; |
| 28 |
|
| 29 |
stdout-path = "framebuffer0"; |
| 30 |
|
| 31 |
framebuffer0: framebuffer@9d400000 { |
| 32 |
compatible = "simple-framebuffer"; |
| 33 |
reg = <0 0x9d400000 0 (1920 * 1080 * 4)>; |
| 34 |
width = <1080>; |
| 35 |
height = <1920>; |
| 36 |
stride = <(1080 * 4)>; |
| 37 |
format = "a8r8g8b8"; |
| 38 |
status = "okay"; |
| 39 |
}; |
| 40 |
}; |
| 41 |
|
| 42 |
board_vbat: vbat-regulator { |
| 43 |
compatible = "regulator-fixed"; |
| 44 |
regulator-name = "VBAT"; |
| 45 |
|
| 46 |
regulator-min-microvolt = <4000000>; |
| 47 |
regulator-max-microvolt = <4000000>; |
| 48 |
regulator-always-on; |
| 49 |
regulator-boot-on; |
| 50 |
}; |
| 51 |
|
| 52 |
vph_pwr: vph-pwr-regulator { |
| 53 |
compatible = "regulator-fixed"; |
| 54 |
regulator-name = "vph_pwr"; |
| 55 |
|
| 56 |
regulator-always-on; |
| 57 |
regulator-boot-on; |
| 58 |
}; |
| 59 |
|
| 60 |
cam_vdig_imx300_219_vreg: cam-vdig-imx300-219-regulator { |
| 61 |
compatible = "regulator-fixed"; |
| 62 |
regulator-name = "cam_vdig_imx300_219_vreg"; |
| 63 |
startup-delay-us = <0>; |
| 64 |
enable-active-high; |
| 65 |
gpio = <&tlmm 52 GPIO_ACTIVE_HIGH>; |
| 66 |
pinctrl-names = "default"; |
| 67 |
pinctrl-0 = <&cam_vdig_default>; |
| 68 |
}; |
| 69 |
|
| 70 |
cam_vana_front_vreg: cam-vana-front-regulator { |
| 71 |
compatible = "regulator-fixed"; |
| 72 |
regulator-name = "cam_vana_front_vreg"; |
| 73 |
startup-delay-us = <0>; |
| 74 |
enable-active-high; |
| 75 |
gpio = <&tlmm 51 GPIO_ACTIVE_HIGH>; |
| 76 |
pinctrl-names = "default"; |
| 77 |
pinctrl-0 = <&imx219_vana_default>; |
| 78 |
}; |
| 79 |
|
| 80 |
cam_vana_rear_vreg: cam-vana-rear-regulator { |
| 81 |
compatible = "regulator-fixed"; |
| 82 |
regulator-name = "cam_vana_rear_vreg"; |
| 83 |
startup-delay-us = <0>; |
| 84 |
enable-active-high; |
| 85 |
gpio = <&tlmm 50 GPIO_ACTIVE_HIGH>; |
| 86 |
regulator-always-on; |
| 87 |
pinctrl-names = "default"; |
| 88 |
pinctrl-0 = <&imx300_vana_default>; |
| 89 |
}; |
| 90 |
|
| 91 |
gpio-keys { |
| 92 |
compatible = "gpio-keys"; |
| 93 |
pinctrl-0 = <&gpio_keys_default>; |
| 94 |
pinctrl-names = "default"; |
| 95 |
|
| 96 |
key-camera-focus { |
| 97 |
label = "Camera Focus"; |
| 98 |
gpios = <&tlmm 64 GPIO_ACTIVE_LOW>; |
| 99 |
linux,input-type = <1>; |
| 100 |
linux,code = <KEY_CAMERA_FOCUS>; |
| 101 |
debounce-interval = <15>; |
| 102 |
}; |
| 103 |
|
| 104 |
key-camera-snapshot { |
| 105 |
label = "Camera Snapshot"; |
| 106 |
gpios = <&tlmm 113 GPIO_ACTIVE_LOW>; |
| 107 |
linux,input-type = <1>; |
| 108 |
linux,code = <KEY_CAMERA>; |
| 109 |
debounce-interval = <15>; |
| 110 |
}; |
| 111 |
|
| 112 |
key-vol-down { |
| 113 |
label = "Volume Down"; |
| 114 |
gpios = <&pm660l_gpios 7 GPIO_ACTIVE_LOW>; |
| 115 |
linux,input-type = <1>; |
| 116 |
linux,code = <KEY_VOLUMEDOWN>; |
| 117 |
wakeup-source; |
| 118 |
debounce-interval = <15>; |
| 119 |
}; |
| 120 |
}; |
| 121 |
|
| 122 |
reserved-memory { |
| 123 |
#address-cells = <2>; |
| 124 |
#size-cells = <2>; |
| 125 |
ranges; |
| 126 |
|
| 127 |
ramoops@ffc00000 { |
| 128 |
compatible = "ramoops"; |
| 129 |
reg = <0x0 0xffc00000 0x0 0x100000>; |
| 130 |
record-size = <0x10000>; |
| 131 |
console-size = <0x60000>; |
| 132 |
ftrace-size = <0x10000>; |
| 133 |
pmsg-size = <0x20000>; |
| 134 |
ecc-size = <16>; |
| 135 |
status = "okay"; |
| 136 |
}; |
| 137 |
|
| 138 |
debug@ffb00000 { |
| 139 |
reg = <0x00 0xffb00000 0x00 0x100000>; |
| 140 |
no-map; |
| 141 |
}; |
| 142 |
|
| 143 |
cont_splash_mem: splash@9d400000 { |
| 144 |
reg = <0 0x9d400000 0 (1920 * 1080 * 4)>; |
| 145 |
no-map; |
| 146 |
}; |
| 147 |
}; |
| 148 |
|
| 149 |
/* |
| 150 |
* Until we hook up type-c detection, we |
| 151 |
* have to stick with this. But it works. |
| 152 |
*/ |
| 153 |
extcon_usb: extcon-usb { |
| 154 |
compatible = "linux,extcon-usb-gpio"; |
| 155 |
id-gpios = <&tlmm 58 GPIO_ACTIVE_HIGH>; |
| 156 |
}; |
| 157 |
}; |
| 158 |
|
| 159 |
&adsp_pil { |
| 160 |
firmware-name = "qcom/sdm630/Sony/nile/adsp.mbn"; |
| 161 |
}; |
| 162 |
|
| 163 |
&blsp_i2c1 { |
| 164 |
status = "okay"; |
| 165 |
|
| 166 |
touchscreen: synaptics-rmi4-i2c@70 { |
| 167 |
compatible = "syna,rmi4-i2c"; |
| 168 |
reg = <0x70>; |
| 169 |
#address-cells = <1>; |
| 170 |
#size-cells = <0>; |
| 171 |
interrupts-extended = <&tlmm 45 0x2008>; |
| 172 |
|
| 173 |
pinctrl-names = "default"; |
| 174 |
pinctrl-0 = <&ts_int_active &ts_lcd_id_active>; |
| 175 |
|
| 176 |
syna,reset-delay-ms = <200>; |
| 177 |
syna,startup-delay-ms = <220>; |
| 178 |
|
| 179 |
rmi4-f01@1 { |
| 180 |
reg = <0x01>; |
| 181 |
syna,nosleep-mode = <1>; |
| 182 |
}; |
| 183 |
|
| 184 |
rmi4-f11@11 { |
| 185 |
reg = <0x11>; |
| 186 |
syna,sensor-type = <1>; |
| 187 |
}; |
| 188 |
}; |
| 189 |
}; |
| 190 |
|
| 191 |
&blsp_i2c2 { |
| 192 |
status = "okay"; |
| 193 |
|
| 194 |
/* SMB1351 charger */ |
| 195 |
}; |
| 196 |
|
| 197 |
/* I2C3, 4, 5, 7 and 8 are disabled on this board. */ |
| 198 |
|
| 199 |
&blsp_i2c6 { |
| 200 |
status = "okay"; |
| 201 |
|
| 202 |
/* NXP NFC */ |
| 203 |
}; |
| 204 |
|
| 205 |
&blsp1_uart2 { |
| 206 |
status = "okay"; |
| 207 |
|
| 208 |
/* MSM serial console */ |
| 209 |
}; |
| 210 |
|
| 211 |
&blsp2_uart1 { |
| 212 |
status = "okay"; |
| 213 |
|
| 214 |
/* HCI Bluetooth */ |
| 215 |
}; |
| 216 |
|
| 217 |
&pm660l_lpg { |
| 218 |
qcom,power-source = <1>; |
| 219 |
|
| 220 |
status = "okay"; |
| 221 |
|
| 222 |
multi-led { |
| 223 |
color = <LED_COLOR_ID_RGB>; |
| 224 |
function = LED_FUNCTION_STATUS; |
| 225 |
|
| 226 |
#address-cells = <1>; |
| 227 |
#size-cells = <0>; |
| 228 |
|
| 229 |
led@1 { |
| 230 |
reg = <1>; |
| 231 |
color = <LED_COLOR_ID_BLUE>; |
| 232 |
}; |
| 233 |
|
| 234 |
led@2 { |
| 235 |
reg = <2>; |
| 236 |
color = <LED_COLOR_ID_GREEN>; |
| 237 |
}; |
| 238 |
|
| 239 |
led@3 { |
| 240 |
reg = <3>; |
| 241 |
color = <LED_COLOR_ID_RED>; |
| 242 |
}; |
| 243 |
}; |
| 244 |
}; |
| 245 |
|
| 246 |
&pm660l_wled { |
| 247 |
status = "okay"; |
| 248 |
|
| 249 |
qcom,switching-freq = <800>; |
| 250 |
qcom,ovp-millivolt = <29600>; |
| 251 |
qcom,current-boost-limit = <970>; |
| 252 |
qcom,current-limit-microamp = <17500>; |
| 253 |
qcom,num-strings = <2>; |
| 254 |
}; |
| 255 |
|
| 256 |
&pon_pwrkey { |
| 257 |
status = "okay"; |
| 258 |
}; |
| 259 |
|
| 260 |
&pon_resin { |
| 261 |
status = "okay"; |
| 262 |
|
| 263 |
linux,code = <KEY_VOLUMEUP>; |
| 264 |
}; |
| 265 |
|
| 266 |
&qhee_code { |
| 267 |
reg = <0x00 0x85800000 0x00 0x3700000>; |
| 268 |
}; |
| 269 |
|
| 270 |
&qusb2phy0 { |
| 271 |
status = "okay"; |
| 272 |
|
| 273 |
vdd-supply = <&vreg_l1b_0p925>; |
| 274 |
vdda-pll-supply = <&vreg_l10a_1p8>; |
| 275 |
vdda-phy-dpdm-supply = <&vreg_l7b_3p125>; |
| 276 |
}; |
| 277 |
|
| 278 |
&rpm_requests { |
| 279 |
regulators-0 { |
| 280 |
compatible = "qcom,rpm-pm660l-regulators"; |
| 281 |
|
| 282 |
vdd_s1-supply = <&vph_pwr>; |
| 283 |
vdd_s2-supply = <&vph_pwr>; |
| 284 |
vdd_s3_s4-supply = <&vph_pwr>; |
| 285 |
vdd_s5-supply = <&vph_pwr>; |
| 286 |
vdd_s6-supply = <&vph_pwr>; |
| 287 |
|
| 288 |
vdd_l1_l9_l10-supply = <&vreg_s2b_1p05>; |
| 289 |
vdd_l2-supply = <&vreg_bob>; |
| 290 |
vdd_l3_l5_l7_l8-supply = <&vreg_bob>; |
| 291 |
vdd_l4_l6-supply = <&vreg_bob>; |
| 292 |
vdd_bob-supply = <&vph_pwr>; |
| 293 |
|
| 294 |
vreg_s1b_1p125: s1 { |
| 295 |
regulator-min-microvolt = <1125000>; |
| 296 |
regulator-max-microvolt = <1125000>; |
| 297 |
regulator-enable-ramp-delay = <200>; |
| 298 |
regulator-ramp-delay = <0>; |
| 299 |
}; |
| 300 |
|
| 301 |
vreg_s2b_1p05: s2 { |
| 302 |
regulator-min-microvolt = <1050000>; |
| 303 |
regulator-max-microvolt = <1050000>; |
| 304 |
regulator-enable-ramp-delay = <200>; |
| 305 |
regulator-ramp-delay = <0>; |
| 306 |
}; |
| 307 |
|
| 308 |
/* |
| 309 |
* At least on Nile's configuration, S3B/S4B (VDD_CX) and |
| 310 |
* S5B (VDD_MX) are managed only through RPM Power Domains. |
| 311 |
* Trying to set a voltage on the main supply will create |
| 312 |
* havoc and freeze the SoC. |
| 313 |
* In any case, reference voltages for these regulators are: |
| 314 |
* S3B/S4B: 0.870V |
| 315 |
* S5B: 0.915V |
| 316 |
*/ |
| 317 |
|
| 318 |
/* LDOs */ |
| 319 |
vreg_l1b_0p925: l1 { |
| 320 |
regulator-min-microvolt = <920000>; |
| 321 |
regulator-max-microvolt = <928000>; |
| 322 |
regulator-enable-ramp-delay = <250>; |
| 323 |
regulator-ramp-delay = <0>; |
| 324 |
regulator-allow-set-load; |
| 325 |
}; |
| 326 |
|
| 327 |
vreg_l2b_2p95: l2 { |
| 328 |
/* |
| 329 |
* This regulator supports 1.648 - 3.104V on this board |
| 330 |
* but we set a max voltage of anything less than 2.7V |
| 331 |
* to satisfy a condition in sdhci.c that will disable |
| 332 |
* 3.3V SDHCI signaling, which happens to be not really |
| 333 |
* supported on the Xperia Nile/Ganges platform. |
| 334 |
*/ |
| 335 |
regulator-min-microvolt = <1648000>; |
| 336 |
regulator-max-microvolt = <2696000>; |
| 337 |
regulator-enable-ramp-delay = <250>; |
| 338 |
regulator-ramp-delay = <0>; |
| 339 |
regulator-allow-set-load; |
| 340 |
}; |
| 341 |
|
| 342 |
vreg_l3b_3p0: l3 { |
| 343 |
regulator-min-microvolt = <2800000>; |
| 344 |
regulator-max-microvolt = <2800000>; |
| 345 |
regulator-enable-ramp-delay = <250>; |
| 346 |
regulator-ramp-delay = <0>; |
| 347 |
regulator-min-microamp = <200>; |
| 348 |
regulator-max-microamp = <600000>; |
| 349 |
regulator-system-load = <100000>; |
| 350 |
regulator-allow-set-load; |
| 351 |
}; |
| 352 |
|
| 353 |
vreg_l4b_2p95: l4 { |
| 354 |
regulator-min-microvolt = <2944000>; |
| 355 |
regulator-max-microvolt = <2952000>; |
| 356 |
regulator-enable-ramp-delay = <250>; |
| 357 |
regulator-ramp-delay = <0>; |
| 358 |
|
| 359 |
regulator-min-microamp = <200>; |
| 360 |
regulator-max-microamp = <600000>; |
| 361 |
regulator-system-load = <570000>; |
| 362 |
regulator-allow-set-load; |
| 363 |
}; |
| 364 |
|
| 365 |
/* |
| 366 |
* Downstream specifies a range of 1721-3600mV, |
| 367 |
* but the only assigned consumers are SDHCI2 VMMC |
| 368 |
* and Coresight QPDI that both request pinned 2.95V. |
| 369 |
* Tighten the range to 1.8-3.328 (closest to 3.3) to |
| 370 |
* make the mmc driver happy. |
| 371 |
*/ |
| 372 |
vreg_l5b_2p95: l5 { |
| 373 |
regulator-min-microvolt = <1800000>; |
| 374 |
regulator-max-microvolt = <3328000>; |
| 375 |
regulator-enable-ramp-delay = <250>; |
| 376 |
regulator-ramp-delay = <0>; |
| 377 |
regulator-allow-set-load; |
| 378 |
regulator-system-load = <800000>; |
| 379 |
}; |
| 380 |
|
| 381 |
vreg_l6b_3p3: l6 { |
| 382 |
regulator-min-microvolt = <1704000>; |
| 383 |
regulator-max-microvolt = <3312000>; |
| 384 |
regulator-enable-ramp-delay = <250>; |
| 385 |
regulator-ramp-delay = <0>; |
| 386 |
}; |
| 387 |
|
| 388 |
vreg_l7b_3p125: l7 { |
| 389 |
regulator-min-microvolt = <2704000>; |
| 390 |
regulator-max-microvolt = <3128000>; |
| 391 |
regulator-enable-ramp-delay = <250>; |
| 392 |
regulator-ramp-delay = <0>; |
| 393 |
}; |
| 394 |
|
| 395 |
vreg_l8b_3p3: l8 { |
| 396 |
regulator-min-microvolt = <2800000>; |
| 397 |
regulator-max-microvolt = <3400000>; |
| 398 |
regulator-enable-ramp-delay = <250>; |
| 399 |
regulator-ramp-delay = <0>; |
| 400 |
}; |
| 401 |
|
| 402 |
/* L9B (870mV) is currently unused */ |
| 403 |
/* L10B (915mV) is currently unused */ |
| 404 |
|
| 405 |
vreg_bob: bob { |
| 406 |
regulator-min-microvolt = <3304000>; |
| 407 |
regulator-max-microvolt = <3624000>; |
| 408 |
regulator-enable-ramp-delay = <500>; |
| 409 |
regulator-ramp-delay = <0>; |
| 410 |
}; |
| 411 |
}; |
| 412 |
|
| 413 |
regulators-1 { |
| 414 |
compatible = "qcom,rpm-pm660-regulators"; |
| 415 |
|
| 416 |
vdd_s1-supply = <&vph_pwr>; |
| 417 |
vdd_s2-supply = <&vph_pwr>; |
| 418 |
vdd_s3-supply = <&vph_pwr>; |
| 419 |
vdd_s4-supply = <&vph_pwr>; |
| 420 |
vdd_s5-supply = <&vph_pwr>; |
| 421 |
vdd_s6-supply = <&vph_pwr>; |
| 422 |
|
| 423 |
vdd_l1_l6_l7-supply = <&vreg_s5a_1p35>; |
| 424 |
vdd_l2_l3-supply = <&vreg_s2b_1p05>; |
| 425 |
vdd_l5-supply = <&vreg_s2b_1p05>; |
| 426 |
vdd_l8_l9_l10_l11_l12_l13_l14-supply = <&vreg_s4a_2p04>; |
| 427 |
vdd_l15_l16_l17_l18_l19-supply = <&vreg_bob>; |
| 428 |
|
| 429 |
/* |
| 430 |
* S1A (FTAPC0), S2A (FTAPC1), S3A (HFAPC1) are managed |
| 431 |
* by the Core Power Reduction hardened (CPRh) and the |
| 432 |
* Operating State Manager (OSM) HW automatically. |
| 433 |
*/ |
| 434 |
|
| 435 |
vreg_s4a_2p04: s4 { |
| 436 |
regulator-min-microvolt = <2040000>; |
| 437 |
regulator-max-microvolt = <2040000>; |
| 438 |
regulator-enable-ramp-delay = <200>; |
| 439 |
regulator-ramp-delay = <0>; |
| 440 |
regulator-always-on; |
| 441 |
}; |
| 442 |
|
| 443 |
vreg_s5a_1p35: s5 { |
| 444 |
regulator-min-microvolt = <1224000>; |
| 445 |
regulator-max-microvolt = <1350000>; |
| 446 |
regulator-enable-ramp-delay = <200>; |
| 447 |
regulator-ramp-delay = <0>; |
| 448 |
}; |
| 449 |
|
| 450 |
vreg_s6a_0p87: s6 { |
| 451 |
regulator-min-microvolt = <504000>; |
| 452 |
regulator-max-microvolt = <992000>; |
| 453 |
regulator-enable-ramp-delay = <150>; |
| 454 |
regulator-ramp-delay = <0>; |
| 455 |
}; |
| 456 |
|
| 457 |
/* LDOs */ |
| 458 |
vreg_l1a_1p225: l1 { |
| 459 |
regulator-min-microvolt = <1226000>; |
| 460 |
regulator-max-microvolt = <1250000>; |
| 461 |
regulator-enable-ramp-delay = <250>; |
| 462 |
regulator-ramp-delay = <0>; |
| 463 |
regulator-allow-set-load; |
| 464 |
}; |
| 465 |
|
| 466 |
vreg_l2a_1p0: l2 { |
| 467 |
regulator-min-microvolt = <944000>; |
| 468 |
regulator-max-microvolt = <1008000>; |
| 469 |
regulator-enable-ramp-delay = <250>; |
| 470 |
regulator-ramp-delay = <0>; |
| 471 |
}; |
| 472 |
|
| 473 |
vreg_l3a_1p0: l3 { |
| 474 |
regulator-min-microvolt = <944000>; |
| 475 |
regulator-max-microvolt = <1008000>; |
| 476 |
regulator-enable-ramp-delay = <250>; |
| 477 |
regulator-ramp-delay = <0>; |
| 478 |
}; |
| 479 |
|
| 480 |
vreg_l5a_0p848: l5 { |
| 481 |
regulator-min-microvolt = <800000>; |
| 482 |
regulator-max-microvolt = <952000>; |
| 483 |
regulator-enable-ramp-delay = <250>; |
| 484 |
regulator-ramp-delay = <0>; |
| 485 |
}; |
| 486 |
|
| 487 |
vreg_l6a_1p3: l6 { |
| 488 |
regulator-min-microvolt = <1304000>; |
| 489 |
regulator-max-microvolt = <1368000>; |
| 490 |
regulator-allow-set-load; |
| 491 |
regulator-enable-ramp-delay = <250>; |
| 492 |
regulator-ramp-delay = <0>; |
| 493 |
}; |
| 494 |
|
| 495 |
vreg_l7a_1p2: l7 { |
| 496 |
regulator-min-microvolt = <1200000>; |
| 497 |
regulator-max-microvolt = <1200000>; |
| 498 |
regulator-enable-ramp-delay = <250>; |
| 499 |
regulator-ramp-delay = <0>; |
| 500 |
}; |
| 501 |
|
| 502 |
vreg_l8a_1p8: l8 { |
| 503 |
regulator-min-microvolt = <1800000>; |
| 504 |
regulator-max-microvolt = <1800000>; |
| 505 |
regulator-enable-ramp-delay = <250>; |
| 506 |
regulator-ramp-delay = <0>; |
| 507 |
regulator-system-load = <325000>; |
| 508 |
regulator-allow-set-load; |
| 509 |
}; |
| 510 |
|
| 511 |
vreg_l9a_1p8: l9 { |
| 512 |
regulator-min-microvolt = <1804000>; |
| 513 |
regulator-max-microvolt = <1896000>; |
| 514 |
regulator-enable-ramp-delay = <250>; |
| 515 |
regulator-ramp-delay = <0>; |
| 516 |
regulator-allow-set-load; |
| 517 |
}; |
| 518 |
|
| 519 |
vreg_l10a_1p8: l10 { |
| 520 |
regulator-min-microvolt = <1800000>; |
| 521 |
regulator-max-microvolt = <1944000>; |
| 522 |
regulator-enable-ramp-delay = <250>; |
| 523 |
regulator-ramp-delay = <0>; |
| 524 |
regulator-allow-set-load; |
| 525 |
}; |
| 526 |
|
| 527 |
vreg_l11a_1p8: l11 { |
| 528 |
regulator-min-microvolt = <1784000>; |
| 529 |
regulator-max-microvolt = <1944000>; |
| 530 |
regulator-enable-ramp-delay = <250>; |
| 531 |
regulator-ramp-delay = <0>; |
| 532 |
}; |
| 533 |
|
| 534 |
vreg_l12a_1p8: l12 { |
| 535 |
regulator-min-microvolt = <1800000>; |
| 536 |
regulator-max-microvolt = <1944000>; |
| 537 |
regulator-enable-ramp-delay = <250>; |
| 538 |
regulator-ramp-delay = <0>; |
| 539 |
}; |
| 540 |
|
| 541 |
/* This gives power to the LPDDR4: never turn it off! */ |
| 542 |
vreg_l13a_1p8: l13 { |
| 543 |
regulator-min-microvolt = <1800000>; |
| 544 |
regulator-max-microvolt = <1944000>; |
| 545 |
regulator-enable-ramp-delay = <250>; |
| 546 |
regulator-ramp-delay = <0>; |
| 547 |
regulator-boot-on; |
| 548 |
regulator-always-on; |
| 549 |
}; |
| 550 |
|
| 551 |
vreg_l14a_1p8: l14 { |
| 552 |
regulator-min-microvolt = <1710000>; |
| 553 |
regulator-max-microvolt = <1904000>; |
| 554 |
regulator-enable-ramp-delay = <250>; |
| 555 |
regulator-ramp-delay = <0>; |
| 556 |
}; |
| 557 |
|
| 558 |
vreg_l15a_1p8: l15 { |
| 559 |
regulator-min-microvolt = <1648000>; |
| 560 |
regulator-max-microvolt = <2952000>; |
| 561 |
regulator-enable-ramp-delay = <250>; |
| 562 |
regulator-ramp-delay = <0>; |
| 563 |
}; |
| 564 |
|
| 565 |
/* L16A (2.70V) is unused */ |
| 566 |
|
| 567 |
vreg_l17a_1p8: l17 { |
| 568 |
regulator-min-microvolt = <1648000>; |
| 569 |
regulator-max-microvolt = <2952000>; |
| 570 |
regulator-enable-ramp-delay = <250>; |
| 571 |
regulator-ramp-delay = <0>; |
| 572 |
}; |
| 573 |
|
| 574 |
vreg_l18a_1v8: l18 { |
| 575 |
regulator-min-microvolt = <1800000>; |
| 576 |
regulator-max-microvolt = <1800000>; |
| 577 |
regulator-enable-ramp-delay = <250>; |
| 578 |
regulator-ramp-delay = <10>; |
| 579 |
regulator-min-microamp = <200>; |
| 580 |
regulator-max-microamp = <50000>; |
| 581 |
regulator-system-load = <10000>; |
| 582 |
regulator-allow-set-load; |
| 583 |
}; |
| 584 |
|
| 585 |
vreg_l19a_3p3: l19 { |
| 586 |
regulator-min-microvolt = <3312000>; |
| 587 |
regulator-max-microvolt = <3400000>; |
| 588 |
regulator-enable-ramp-delay = <250>; |
| 589 |
regulator-ramp-delay = <0>; |
| 590 |
regulator-allow-set-load; |
| 591 |
}; |
| 592 |
}; |
| 593 |
}; |
| 594 |
|
| 595 |
&sdc2_state_on { |
| 596 |
sd-cd-pins { |
| 597 |
pins = "gpio54"; |
| 598 |
function = "gpio"; |
| 599 |
bias-pull-up; |
| 600 |
drive-strength = <2>; |
| 601 |
}; |
| 602 |
}; |
| 603 |
|
| 604 |
&sdc2_state_off { |
| 605 |
sd-cd-pins { |
| 606 |
pins = "gpio54"; |
| 607 |
function = "gpio"; |
| 608 |
bias-disable; |
| 609 |
drive-strength = <2>; |
| 610 |
}; |
| 611 |
}; |
| 612 |
|
| 613 |
&sdhc_1 { |
| 614 |
status = "okay"; |
| 615 |
supports-cqe; |
| 616 |
|
| 617 |
/* SoMC Nile platform's eMMC doesn't support HS200 mode */ |
| 618 |
mmc-ddr-1_8v; |
| 619 |
mmc-hs400-1_8v; |
| 620 |
mmc-hs400-enhanced-strobe; |
| 621 |
|
| 622 |
vmmc-supply = <&vreg_l4b_2p95>; |
| 623 |
vqmmc-supply = <&vreg_l8a_1p8>; |
| 624 |
}; |
| 625 |
|
| 626 |
&sdhc_2 { |
| 627 |
status = "okay"; |
| 628 |
|
| 629 |
vmmc-supply = <&vreg_l5b_2p95>; |
| 630 |
vqmmc-supply = <&vreg_l2b_2p95>; |
| 631 |
}; |
| 632 |
|
| 633 |
&tlmm { |
| 634 |
gpio-reserved-ranges = <8 4>; |
| 635 |
|
| 636 |
ts_int_active: ts-int-active-state { |
| 637 |
pins = "gpio45"; |
| 638 |
function = "gpio"; |
| 639 |
drive-strength = <8>; |
| 640 |
bias-pull-up; |
| 641 |
}; |
| 642 |
|
| 643 |
ts_lcd_id_active: ts-lcd-id-active-state { |
| 644 |
pins = "gpio56"; |
| 645 |
function = "gpio"; |
| 646 |
drive-strength = <8>; |
| 647 |
bias-disable; |
| 648 |
}; |
| 649 |
|
| 650 |
gpio_keys_default: gpio-keys-default-state { |
| 651 |
pins = "gpio64", "gpio113"; |
| 652 |
function = "gpio"; |
| 653 |
drive-strength = <2>; |
| 654 |
bias-pull-up; |
| 655 |
}; |
| 656 |
|
| 657 |
imx300_vana_default: imx300-vana-default-state { |
| 658 |
pins = "gpio50"; |
| 659 |
function = "gpio"; |
| 660 |
bias-disable; |
| 661 |
drive-strength = <2>; |
| 662 |
}; |
| 663 |
|
| 664 |
imx219_vana_default: imx219-vana-default-state { |
| 665 |
pins = "gpio51"; |
| 666 |
function = "gpio"; |
| 667 |
bias-disable; |
| 668 |
drive-strength = <2>; |
| 669 |
}; |
| 670 |
|
| 671 |
cam_vdig_default: cam-vdig-default-state { |
| 672 |
pins = "gpio52"; |
| 673 |
function = "gpio"; |
| 674 |
bias-disable; |
| 675 |
drive-strength = <2>; |
| 676 |
}; |
| 677 |
}; |
| 678 |
|
| 679 |
&usb3 { |
| 680 |
qcom,select-utmi-as-pipe-clk; |
| 681 |
|
| 682 |
status = "okay"; |
| 683 |
}; |
| 684 |
|
| 685 |
&usb3_dwc3 { |
| 686 |
maximum-speed = "high-speed"; |
| 687 |
phys = <&qusb2phy0>; |
| 688 |
phy-names = "usb2-phy"; |
| 689 |
|
| 690 |
dr_mode = "peripheral"; |
| 691 |
extcon = <&extcon_usb>; |
| 692 |
}; |