| 1 |
// SPDX-License-Identifier: BSD-3-Clause |
| 2 |
/* |
| 3 |
* Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. |
| 4 |
* Copyright (c) 2021-2023, Linaro Limited |
| 5 |
*/ |
| 6 |
|
| 7 |
#include <dt-bindings/input/input.h> |
| 8 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 9 |
#include <dt-bindings/spmi/spmi.h> |
| 10 |
#include <dt-bindings/iio/qcom,spmi-vadc.h> |
| 11 |
|
| 12 |
/ { |
| 13 |
thermal-zones { |
| 14 |
pmc8180-thermal { |
| 15 |
polling-delay-passive = <100>; |
| 16 |
|
| 17 |
thermal-sensors = <&pmc8180_temp>; |
| 18 |
|
| 19 |
trips { |
| 20 |
trip0 { |
| 21 |
temperature = <95000>; |
| 22 |
hysteresis = <0>; |
| 23 |
type = "passive"; |
| 24 |
}; |
| 25 |
|
| 26 |
trip1 { |
| 27 |
temperature = <115000>; |
| 28 |
hysteresis = <0>; |
| 29 |
type = "hot"; |
| 30 |
}; |
| 31 |
|
| 32 |
trip2 { |
| 33 |
temperature = <145000>; |
| 34 |
hysteresis = <0>; |
| 35 |
type = "critical"; |
| 36 |
}; |
| 37 |
}; |
| 38 |
}; |
| 39 |
|
| 40 |
pmc8180c-thermal { |
| 41 |
polling-delay-passive = <100>; |
| 42 |
|
| 43 |
thermal-sensors = <&pmc8180c_temp>; |
| 44 |
|
| 45 |
trips { |
| 46 |
trip0 { |
| 47 |
temperature = <95000>; |
| 48 |
hysteresis = <0>; |
| 49 |
type = "passive"; |
| 50 |
}; |
| 51 |
|
| 52 |
trip1 { |
| 53 |
temperature = <115000>; |
| 54 |
hysteresis = <0>; |
| 55 |
type = "hot"; |
| 56 |
}; |
| 57 |
|
| 58 |
trip2 { |
| 59 |
temperature = <145000>; |
| 60 |
hysteresis = <0>; |
| 61 |
type = "critical"; |
| 62 |
}; |
| 63 |
}; |
| 64 |
}; |
| 65 |
}; |
| 66 |
}; |
| 67 |
|
| 68 |
&spmi_bus { |
| 69 |
pmc8180_0: pmic@0 { |
| 70 |
compatible = "qcom,pm8150", "qcom,spmi-pmic"; |
| 71 |
reg = <0x0 SPMI_USID>; |
| 72 |
#address-cells = <1>; |
| 73 |
#size-cells = <0>; |
| 74 |
|
| 75 |
pon: pon@800 { |
| 76 |
compatible = "qcom,pm8916-pon"; |
| 77 |
reg = <0x0800>; |
| 78 |
pmc8180_pwrkey: pwrkey { |
| 79 |
compatible = "qcom,pm8941-pwrkey"; |
| 80 |
interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>; |
| 81 |
debounce = <15625>; |
| 82 |
bias-pull-up; |
| 83 |
linux,code = <KEY_POWER>; |
| 84 |
|
| 85 |
status = "disabled"; |
| 86 |
}; |
| 87 |
}; |
| 88 |
|
| 89 |
pmc8180_temp: temp-alarm@2400 { |
| 90 |
compatible = "qcom,spmi-temp-alarm"; |
| 91 |
reg = <0x2400>; |
| 92 |
interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; |
| 93 |
io-channels = <&pmc8180_adc ADC5_DIE_TEMP>; |
| 94 |
io-channel-names = "thermal"; |
| 95 |
#thermal-sensor-cells = <0>; |
| 96 |
}; |
| 97 |
|
| 98 |
pmc8180_adc: adc@3100 { |
| 99 |
compatible = "qcom,spmi-adc5"; |
| 100 |
reg = <0x3100>; |
| 101 |
#address-cells = <1>; |
| 102 |
#size-cells = <0>; |
| 103 |
#io-channel-cells = <1>; |
| 104 |
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| 105 |
|
| 106 |
channel@0 { |
| 107 |
reg = <ADC5_REF_GND>; |
| 108 |
qcom,pre-scaling = <1 1>; |
| 109 |
label = "ref_gnd"; |
| 110 |
}; |
| 111 |
|
| 112 |
channel@1 { |
| 113 |
reg = <ADC5_1P25VREF>; |
| 114 |
qcom,pre-scaling = <1 1>; |
| 115 |
label = "vref_1p25"; |
| 116 |
}; |
| 117 |
|
| 118 |
channel@6 { |
| 119 |
reg = <ADC5_DIE_TEMP>; |
| 120 |
qcom,pre-scaling = <1 1>; |
| 121 |
label = "die_temp"; |
| 122 |
}; |
| 123 |
}; |
| 124 |
|
| 125 |
pmc8180_adc_tm: adc-tm@3500 { |
| 126 |
compatible = "qcom,spmi-adc-tm5"; |
| 127 |
reg = <0x3500>; |
| 128 |
interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; |
| 129 |
#thermal-sensor-cells = <1>; |
| 130 |
#address-cells = <1>; |
| 131 |
#size-cells = <0>; |
| 132 |
status = "disabled"; |
| 133 |
}; |
| 134 |
|
| 135 |
rtc@6000 { |
| 136 |
compatible = "qcom,pm8941-rtc"; |
| 137 |
reg = <0x6000>; |
| 138 |
reg-names = "rtc", "alarm"; |
| 139 |
interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; |
| 140 |
}; |
| 141 |
|
| 142 |
pmc8180_1_gpios: gpio@c000 { |
| 143 |
compatible = "qcom,pmc8180-gpio", "qcom,spmi-gpio"; |
| 144 |
reg = <0xc000>; |
| 145 |
gpio-controller; |
| 146 |
gpio-ranges = <&pmc8180_1_gpios 0 0 10>; |
| 147 |
#gpio-cells = <2>; |
| 148 |
interrupt-controller; |
| 149 |
#interrupt-cells = <2>; |
| 150 |
}; |
| 151 |
}; |
| 152 |
|
| 153 |
pmic@1 { |
| 154 |
compatible = "qcom,pmc8180", "qcom,spmi-pmic"; |
| 155 |
reg = <0x1 SPMI_USID>; |
| 156 |
#address-cells = <1>; |
| 157 |
#size-cells = <0>; |
| 158 |
}; |
| 159 |
|
| 160 |
pmic@2 { |
| 161 |
compatible = "qcom,smb2351", "qcom,spmi-pmic"; |
| 162 |
reg = <0x2 SPMI_USID>; |
| 163 |
#address-cells = <1>; |
| 164 |
#size-cells = <0>; |
| 165 |
|
| 166 |
adc@3100 { |
| 167 |
compatible = "qcom,spmi-adc-rev2"; |
| 168 |
reg = <0x3100>; |
| 169 |
#address-cells = <1>; |
| 170 |
#size-cells = <0>; |
| 171 |
#io-channel-cells = <1>; |
| 172 |
interrupts = <0x2 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| 173 |
|
| 174 |
channel@0 { |
| 175 |
reg = <ADC5_REF_GND>; |
| 176 |
qcom,pre-scaling = <1 1>; |
| 177 |
label = "ref_gnd"; |
| 178 |
}; |
| 179 |
|
| 180 |
channel@1 { |
| 181 |
reg = <ADC5_1P25VREF>; |
| 182 |
qcom,pre-scaling = <1 1>; |
| 183 |
label = "vref_1p25"; |
| 184 |
}; |
| 185 |
|
| 186 |
channel@85 { |
| 187 |
reg = <0x85>; |
| 188 |
qcom,pre-scaling = <1 1>; |
| 189 |
label = "vcoin2"; |
| 190 |
}; |
| 191 |
}; |
| 192 |
}; |
| 193 |
|
| 194 |
pmic@6 { |
| 195 |
compatible = "qcom,pm8150c", "qcom,spmi-pmic"; |
| 196 |
reg = <0x6 SPMI_USID>; |
| 197 |
#address-cells = <1>; |
| 198 |
#size-cells = <0>; |
| 199 |
}; |
| 200 |
|
| 201 |
pmc8180_2: pmic@8 { |
| 202 |
compatible = "qcom,pm8150", "qcom,spmi-pmic"; |
| 203 |
reg = <0x8 SPMI_USID>; |
| 204 |
#address-cells = <1>; |
| 205 |
#size-cells = <0>; |
| 206 |
|
| 207 |
pmc8180_2_gpios: gpio@c000 { |
| 208 |
compatible = "qcom,pmc8180-gpio", "qcom,spmi-gpio"; |
| 209 |
reg = <0xc000>; |
| 210 |
gpio-controller; |
| 211 |
gpio-ranges = <&pmc8180_2_gpios 0 0 10>; |
| 212 |
#gpio-cells = <2>; |
| 213 |
interrupt-controller; |
| 214 |
#interrupt-cells = <2>; |
| 215 |
}; |
| 216 |
}; |
| 217 |
|
| 218 |
pmic@a { |
| 219 |
compatible = "qcom,smb2351", "qcom,spmi-pmic"; |
| 220 |
reg = <0xa SPMI_USID>; |
| 221 |
#address-cells = <1>; |
| 222 |
#size-cells = <0>; |
| 223 |
|
| 224 |
adc@3100 { |
| 225 |
compatible = "qcom,spmi-adc-rev2"; |
| 226 |
reg = <0x3100>; |
| 227 |
#address-cells = <1>; |
| 228 |
#size-cells = <0>; |
| 229 |
#io-channel-cells = <1>; |
| 230 |
interrupts = <0xa 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| 231 |
|
| 232 |
channel@0 { |
| 233 |
reg = <ADC5_REF_GND>; |
| 234 |
qcom,pre-scaling = <1 1>; |
| 235 |
label = "ref_gnd"; |
| 236 |
}; |
| 237 |
|
| 238 |
channel@1 { |
| 239 |
reg = <ADC5_1P25VREF>; |
| 240 |
qcom,pre-scaling = <1 1>; |
| 241 |
label = "vref_1p25"; |
| 242 |
}; |
| 243 |
|
| 244 |
channel@85 { |
| 245 |
reg = <0x85>; |
| 246 |
qcom,pre-scaling = <1 1>; |
| 247 |
label = "vcoin"; |
| 248 |
}; |
| 249 |
}; |
| 250 |
}; |
| 251 |
|
| 252 |
pmic@4 { |
| 253 |
compatible = "qcom,pm8150c", "qcom,spmi-pmic"; |
| 254 |
reg = <0x4 SPMI_USID>; |
| 255 |
#address-cells = <1>; |
| 256 |
#size-cells = <0>; |
| 257 |
|
| 258 |
pon@800 { |
| 259 |
compatible = "qcom,pm8916-pon"; |
| 260 |
reg = <0x0800>; |
| 261 |
|
| 262 |
status = "disabled"; |
| 263 |
}; |
| 264 |
|
| 265 |
pmc8180c_temp: temp-alarm@2400 { |
| 266 |
compatible = "qcom,spmi-temp-alarm"; |
| 267 |
reg = <0x2400>; |
| 268 |
interrupts = <0x4 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; |
| 269 |
io-channels = <&pmc8180c_adc ADC5_DIE_TEMP>; |
| 270 |
io-channel-names = "thermal"; |
| 271 |
#thermal-sensor-cells = <0>; |
| 272 |
}; |
| 273 |
|
| 274 |
pmc8180c_adc: adc@3100 { |
| 275 |
compatible = "qcom,spmi-adc5"; |
| 276 |
reg = <0x3100>; |
| 277 |
#address-cells = <1>; |
| 278 |
#size-cells = <0>; |
| 279 |
#io-channel-cells = <1>; |
| 280 |
interrupts = <0x4 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| 281 |
|
| 282 |
channel@0 { |
| 283 |
reg = <ADC5_REF_GND>; |
| 284 |
qcom,pre-scaling = <1 1>; |
| 285 |
label = "ref_gnd"; |
| 286 |
}; |
| 287 |
|
| 288 |
channel@1 { |
| 289 |
reg = <ADC5_1P25VREF>; |
| 290 |
qcom,pre-scaling = <1 1>; |
| 291 |
label = "vref_1p25"; |
| 292 |
}; |
| 293 |
|
| 294 |
channel@6 { |
| 295 |
reg = <ADC5_DIE_TEMP>; |
| 296 |
qcom,pre-scaling = <1 1>; |
| 297 |
label = "die_temp"; |
| 298 |
}; |
| 299 |
}; |
| 300 |
|
| 301 |
pmc8180c_adc_tm: adc-tm@3500 { |
| 302 |
compatible = "qcom,spmi-adc-tm5"; |
| 303 |
reg = <0x3500>; |
| 304 |
interrupts = <0x4 0x35 0x0 IRQ_TYPE_EDGE_RISING>; |
| 305 |
#thermal-sensor-cells = <1>; |
| 306 |
#address-cells = <1>; |
| 307 |
#size-cells = <0>; |
| 308 |
status = "disabled"; |
| 309 |
}; |
| 310 |
|
| 311 |
pmc8180c_gpios: gpio@c000 { |
| 312 |
compatible = "qcom,pmc8180c-gpio", "qcom,spmi-gpio"; |
| 313 |
reg = <0xc000>; |
| 314 |
gpio-controller; |
| 315 |
gpio-ranges = <&pmc8180c_gpios 0 0 12>; |
| 316 |
#gpio-cells = <2>; |
| 317 |
interrupt-controller; |
| 318 |
#interrupt-cells = <2>; |
| 319 |
}; |
| 320 |
}; |
| 321 |
|
| 322 |
pmic@5 { |
| 323 |
compatible = "qcom,pmc8180c", "qcom,spmi-pmic"; |
| 324 |
reg = <0x5 SPMI_USID>; |
| 325 |
|
| 326 |
pmc8180c_lpg: pwm { |
| 327 |
compatible = "qcom,pmc8180c-lpg"; |
| 328 |
|
| 329 |
#address-cells = <1>; |
| 330 |
#size-cells = <0>; |
| 331 |
#pwm-cells = <2>; |
| 332 |
|
| 333 |
status = "disabled"; |
| 334 |
}; |
| 335 |
}; |
| 336 |
}; |