| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* sc7280 Qcard device tree source |
| 4 |
* |
| 5 |
* Qcard PCB has the processor, RAM, eMMC (if stuffed), and eDP connector (if |
| 6 |
* stuffed) on it. This device tree tries to encapsulate all the things that |
| 7 |
* all boards using Qcard will have in common. Given that there are stuffing |
| 8 |
* options, some things may be left with status "disabled" and enabled in |
| 9 |
* the actual board device tree files. |
| 10 |
* |
| 11 |
* Copyright 2022 Google LLC. |
| 12 |
*/ |
| 13 |
|
| 14 |
#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h> |
| 15 |
#include <dt-bindings/iio/qcom,spmi-adc7-pmr735a.h> |
| 16 |
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| 17 |
#include <dt-bindings/regulator/qcom,rpmh-regulator.h> |
| 18 |
|
| 19 |
#include "kodiak.dtsi" |
| 20 |
|
| 21 |
/* PMICs depend on spmi_bus label and so must come after SoC */ |
| 22 |
#include "pm7325.dtsi" |
| 23 |
#include "pm8350c.dtsi" |
| 24 |
#include "pmk8350.dtsi" |
| 25 |
|
| 26 |
/ { |
| 27 |
aliases { |
| 28 |
bluetooth0 = &bluetooth; |
| 29 |
serial0 = &uart5; |
| 30 |
serial1 = &uart7; |
| 31 |
wifi0 = &wifi; |
| 32 |
}; |
| 33 |
|
| 34 |
wcd9385: audio-codec-1 { |
| 35 |
compatible = "qcom,wcd9385-codec"; |
| 36 |
pinctrl-names = "default", "sleep"; |
| 37 |
pinctrl-0 = <&wcd_reset_n>, <&us_euro_hs_sel>; |
| 38 |
pinctrl-1 = <&wcd_reset_n_sleep>, <&us_euro_hs_sel>; |
| 39 |
|
| 40 |
reset-gpios = <&tlmm 83 GPIO_ACTIVE_LOW>; |
| 41 |
us-euro-gpios = <&tlmm 81 GPIO_ACTIVE_HIGH>; |
| 42 |
|
| 43 |
qcom,rx-device = <&wcd_rx>; |
| 44 |
qcom,tx-device = <&wcd_tx>; |
| 45 |
|
| 46 |
vdd-rxtx-supply = <&vreg_l18b_1p8>; |
| 47 |
vdd-io-supply = <&vreg_l18b_1p8>; |
| 48 |
vdd-buck-supply = <&vreg_l17b_1p8>; |
| 49 |
vdd-mic-bias-supply = <&vreg_bob>; |
| 50 |
|
| 51 |
qcom,micbias1-microvolt = <1800000>; |
| 52 |
qcom,micbias2-microvolt = <1800000>; |
| 53 |
qcom,micbias3-microvolt = <1800000>; |
| 54 |
qcom,micbias4-microvolt = <1800000>; |
| 55 |
|
| 56 |
qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 |
| 57 |
500000 500000 500000>; |
| 58 |
qcom,mbhc-headset-vthreshold-microvolt = <1700000>; |
| 59 |
qcom,mbhc-headphone-vthreshold-microvolt = <50000>; |
| 60 |
#sound-dai-cells = <1>; |
| 61 |
|
| 62 |
status = "disabled"; |
| 63 |
}; |
| 64 |
|
| 65 |
pm8350c_pwm_backlight: backlight { |
| 66 |
compatible = "pwm-backlight"; |
| 67 |
status = "disabled"; |
| 68 |
|
| 69 |
enable-gpios = <&pm8350c_gpios 7 GPIO_ACTIVE_HIGH>; |
| 70 |
pinctrl-names = "default"; |
| 71 |
pinctrl-0 = <&pmic_edp_bl_en>; |
| 72 |
pwms = <&pm8350c_pwm 3 65535>; |
| 73 |
}; |
| 74 |
}; |
| 75 |
|
| 76 |
&apps_rsc { |
| 77 |
/* |
| 78 |
* Regulators are given labels corresponding to the various names |
| 79 |
* they are referred to on schematics. They are also given labels |
| 80 |
* corresponding to named voltage inputs on the SoC or components |
| 81 |
* bundled with the SoC (like radio companion chips). We totally |
| 82 |
* ignore it when one regulator is the input to another regulator. |
| 83 |
* That's handled automatically by the initial config given to |
| 84 |
* RPMH by the firmware. |
| 85 |
* |
| 86 |
* Regulators that the HLOS (High Level OS) doesn't touch at all |
| 87 |
* are left out of here since they are managed elsewhere. |
| 88 |
*/ |
| 89 |
|
| 90 |
regulators-0 { |
| 91 |
compatible = "qcom,pm7325-rpmh-regulators"; |
| 92 |
qcom,pmic-id = "b"; |
| 93 |
|
| 94 |
vdd19_pmu_pcie_i: |
| 95 |
vdd19_pmu_rfa_i: |
| 96 |
vreg_s1b_1p856: smps1 { |
| 97 |
regulator-min-microvolt = <1856000>; |
| 98 |
regulator-max-microvolt = <2040000>; |
| 99 |
}; |
| 100 |
|
| 101 |
vdd_pmu_aon_i: |
| 102 |
vdd09_pmu_rfa_i: |
| 103 |
vdd095_mx_pmu: |
| 104 |
vdd095_pmu: |
| 105 |
vreg_s7b_0p952: smps7 { |
| 106 |
regulator-min-microvolt = <535000>; |
| 107 |
regulator-max-microvolt = <1120000>; |
| 108 |
}; |
| 109 |
|
| 110 |
vdd13_pmu_rfa_i: |
| 111 |
vdd13_pmu_pcie_i: |
| 112 |
vreg_s8b_1p256: smps8 { |
| 113 |
regulator-min-microvolt = <1256000>; |
| 114 |
regulator-max-microvolt = <1500000>; |
| 115 |
}; |
| 116 |
|
| 117 |
vdd_a_usbssdp_0_core: |
| 118 |
vreg_l1b_0p912: ldo1 { |
| 119 |
regulator-min-microvolt = <825000>; |
| 120 |
regulator-max-microvolt = <925000>; |
| 121 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 122 |
}; |
| 123 |
|
| 124 |
vdd_a_usbhs_3p1: |
| 125 |
vreg_l2b_3p072: ldo2 { |
| 126 |
regulator-min-microvolt = <2700000>; |
| 127 |
regulator-max-microvolt = <3544000>; |
| 128 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 129 |
}; |
| 130 |
|
| 131 |
vdd_a_csi_0_1_1p2: |
| 132 |
vdd_a_csi_2_3_1p2: |
| 133 |
vdd_a_csi_4_1p2: |
| 134 |
vdd_a_dsi_0_1p2: |
| 135 |
vdd_a_edp_0_1p2: |
| 136 |
vdd_a_qlink_0_1p2: |
| 137 |
vdd_a_qlink_1_1p2: |
| 138 |
vdd_a_pcie_0_1p2: |
| 139 |
vdd_a_pcie_1_1p2: |
| 140 |
vdd_a_ufs_0_1p2: |
| 141 |
vdd_a_usbssdp_0_1p2: |
| 142 |
vreg_l6b_1p2: ldo6 { |
| 143 |
regulator-min-microvolt = <1140000>; |
| 144 |
regulator-max-microvolt = <1260000>; |
| 145 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 146 |
}; |
| 147 |
|
| 148 |
/* |
| 149 |
* Despite the fact that this is named to be 2.5V on the |
| 150 |
* schematic, it powers eMMC which doesn't accept 2.5V |
| 151 |
*/ |
| 152 |
vreg_l7b_2p5: ldo7 { |
| 153 |
regulator-min-microvolt = <2960000>; |
| 154 |
regulator-max-microvolt = <2960000>; |
| 155 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 156 |
}; |
| 157 |
|
| 158 |
vreg_l17b_1p8: ldo17 { |
| 159 |
regulator-min-microvolt = <1700000>; |
| 160 |
regulator-max-microvolt = <1900000>; |
| 161 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 162 |
}; |
| 163 |
|
| 164 |
vdd_px_wcd9385: |
| 165 |
vdd_txrx: |
| 166 |
vddpx_0: |
| 167 |
vddpx_3: |
| 168 |
vddpx_7: |
| 169 |
vreg_l18b_1p8: ldo18 { |
| 170 |
regulator-min-microvolt = <1800000>; |
| 171 |
regulator-max-microvolt = <2000000>; |
| 172 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 173 |
}; |
| 174 |
|
| 175 |
vdd_1p8: |
| 176 |
vdd_px_sdr735: |
| 177 |
vdd_pxm: |
| 178 |
vdd18_io: |
| 179 |
vddio_px_1: |
| 180 |
vddio_px_2: |
| 181 |
vddio_px_3: |
| 182 |
vddpx_ts: |
| 183 |
vddpx_wl4otp: |
| 184 |
vreg_l19b_1p8: ldo19 { |
| 185 |
regulator-min-microvolt = <1800000>; |
| 186 |
regulator-max-microvolt = <1800000>; |
| 187 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 188 |
}; |
| 189 |
}; |
| 190 |
|
| 191 |
regulators-1 { |
| 192 |
compatible = "qcom,pm8350c-rpmh-regulators"; |
| 193 |
qcom,pmic-id = "c"; |
| 194 |
|
| 195 |
vdd22_wlbtpa_ch0: |
| 196 |
vdd22_wlbtpa_ch1: |
| 197 |
vdd22_wlbtppa_ch0: |
| 198 |
vdd22_wlbtppa_ch1: |
| 199 |
vdd22_wlpa5g_ch0: |
| 200 |
vdd22_wlpa5g_ch1: |
| 201 |
vdd22_wlppa5g_ch0: |
| 202 |
vdd22_wlppa5g_ch1: |
| 203 |
vreg_s1c_2p2: smps1 { |
| 204 |
regulator-min-microvolt = <2190000>; |
| 205 |
regulator-max-microvolt = <2210000>; |
| 206 |
}; |
| 207 |
|
| 208 |
lp4_vdd2_1p052: |
| 209 |
vreg_s9c_0p676: smps9 { |
| 210 |
regulator-min-microvolt = <1010000>; |
| 211 |
regulator-max-microvolt = <1170000>; |
| 212 |
}; |
| 213 |
|
| 214 |
vdda_apc_cs_1p8: |
| 215 |
vdda_gfx_cs_1p8: |
| 216 |
vdda_turing_q6_cs_1p8: |
| 217 |
vdd_a_cxo_1p8: |
| 218 |
vdd_a_qrefs_1p8: |
| 219 |
vdd_a_usbhs_1p8: |
| 220 |
vdd_qfprom: |
| 221 |
vreg_l1c_1p8: ldo1 { |
| 222 |
regulator-min-microvolt = <1800000>; |
| 223 |
regulator-max-microvolt = <1980000>; |
| 224 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 225 |
}; |
| 226 |
|
| 227 |
vreg_l2c_1p8: ldo2 { |
| 228 |
regulator-min-microvolt = <1620000>; |
| 229 |
regulator-max-microvolt = <1980000>; |
| 230 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 231 |
}; |
| 232 |
|
| 233 |
/* |
| 234 |
* The initial design of this regulator was to use it as 3.3V, |
| 235 |
* but due to later changes in design it was changed to 1.8V. |
| 236 |
* The original name is kept due to same schematic. |
| 237 |
*/ |
| 238 |
ts_avccio: |
| 239 |
vreg_l3c_3p0: ldo3 { |
| 240 |
regulator-min-microvolt = <1800000>; |
| 241 |
regulator-max-microvolt = <1800000>; |
| 242 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 243 |
}; |
| 244 |
|
| 245 |
vddpx_5: |
| 246 |
vreg_l4c_1p8_3p0: ldo4 { |
| 247 |
regulator-min-microvolt = <1620000>; |
| 248 |
regulator-max-microvolt = <3300000>; |
| 249 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 250 |
}; |
| 251 |
|
| 252 |
vddpx_6: |
| 253 |
vreg_l5c_1p8_3p0: ldo5 { |
| 254 |
regulator-min-microvolt = <1620000>; |
| 255 |
regulator-max-microvolt = <3300000>; |
| 256 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 257 |
}; |
| 258 |
|
| 259 |
vddpx_2: |
| 260 |
vreg_l6c_2p96: ldo6 { |
| 261 |
regulator-min-microvolt = <1800000>; |
| 262 |
regulator-max-microvolt = <2950000>; |
| 263 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 264 |
}; |
| 265 |
|
| 266 |
vreg_l7c_3p0: ldo7 { |
| 267 |
regulator-min-microvolt = <3000000>; |
| 268 |
regulator-max-microvolt = <3544000>; |
| 269 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 270 |
}; |
| 271 |
|
| 272 |
vreg_l8c_1p8: ldo8 { |
| 273 |
regulator-min-microvolt = <1620000>; |
| 274 |
regulator-max-microvolt = <2000000>; |
| 275 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 276 |
}; |
| 277 |
|
| 278 |
vreg_l9c_2p96: ldo9 { |
| 279 |
regulator-min-microvolt = <2960000>; |
| 280 |
regulator-max-microvolt = <2960000>; |
| 281 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 282 |
}; |
| 283 |
|
| 284 |
vdd_a_csi_0_1_0p9: |
| 285 |
vdd_a_csi_2_3_0p9: |
| 286 |
vdd_a_csi_4_0p9: |
| 287 |
vdd_a_dsi_0_0p9: |
| 288 |
vdd_a_dsi_0_pll_0p9: |
| 289 |
vdd_a_edp_0_0p9: |
| 290 |
vdd_a_gnss_0p9: |
| 291 |
vdd_a_pcie_0_core: |
| 292 |
vdd_a_pcie_1_core: |
| 293 |
vdd_a_qlink_0_0p9: |
| 294 |
vdd_a_qlink_0_0p9_ck: |
| 295 |
vdd_a_qlink_1_0p9: |
| 296 |
vdd_a_qlink_1_0p9_ck: |
| 297 |
vdd_a_qrefs_0p875_0: |
| 298 |
vdd_a_qrefs_0p875_1: |
| 299 |
vdd_a_qrefs_0p875_2: |
| 300 |
vdd_a_qrefs_0p875_3: |
| 301 |
vdd_a_qrefs_0p875_4_5: |
| 302 |
vdd_a_qrefs_0p875_6: |
| 303 |
vdd_a_qrefs_0p875_7: |
| 304 |
vdd_a_qrefs_0p875_8: |
| 305 |
vdd_a_qrefs_0p875_9: |
| 306 |
vdd_a_ufs_0_core: |
| 307 |
vdd_a_usbhs_core: |
| 308 |
vreg_l10c_0p88: ldo10 { |
| 309 |
regulator-min-microvolt = <720000>; |
| 310 |
regulator-max-microvolt = <1050000>; |
| 311 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 312 |
}; |
| 313 |
|
| 314 |
vreg_l11c_2p8: ldo11 { |
| 315 |
regulator-min-microvolt = <2800000>; |
| 316 |
regulator-max-microvolt = <3544000>; |
| 317 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 318 |
}; |
| 319 |
|
| 320 |
vreg_l12c_1p8: ldo12 { |
| 321 |
regulator-min-microvolt = <1650000>; |
| 322 |
regulator-max-microvolt = <2000000>; |
| 323 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 324 |
}; |
| 325 |
|
| 326 |
vreg_l13c_3p0: ldo13 { |
| 327 |
regulator-min-microvolt = <2700000>; |
| 328 |
regulator-max-microvolt = <3544000>; |
| 329 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>; |
| 330 |
}; |
| 331 |
|
| 332 |
vdd_flash: |
| 333 |
vdd_iris_rgb: |
| 334 |
vdd_mic_bias: |
| 335 |
vreg_bob: bob { |
| 336 |
regulator-min-microvolt = <3008000>; |
| 337 |
regulator-max-microvolt = <3960000>; |
| 338 |
regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>; |
| 339 |
}; |
| 340 |
}; |
| 341 |
}; |
| 342 |
|
| 343 |
/* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */ |
| 344 |
|
| 345 |
&lpass_va_macro { |
| 346 |
vdd-micb-supply = <&vreg_bob>; |
| 347 |
}; |
| 348 |
|
| 349 |
/* NOTE: Not all Qcards have eDP connector stuffed */ |
| 350 |
&mdss_edp { |
| 351 |
aux-bus { |
| 352 |
edp_panel: panel { |
| 353 |
compatible = "edp-panel"; |
| 354 |
|
| 355 |
backlight = <&pm8350c_pwm_backlight>; |
| 356 |
|
| 357 |
port { |
| 358 |
edp_panel_in: endpoint { |
| 359 |
remote-endpoint = <&mdss_edp_out>; |
| 360 |
}; |
| 361 |
}; |
| 362 |
}; |
| 363 |
}; |
| 364 |
}; |
| 365 |
|
| 366 |
&mdss_edp_out { |
| 367 |
remote-endpoint = <&edp_panel_in>; |
| 368 |
}; |
| 369 |
|
| 370 |
&mdss_edp_phy { |
| 371 |
vdda-pll-supply = <&vdd_a_edp_0_0p9>; |
| 372 |
vdda-phy-supply = <&vdd_a_edp_0_1p2>; |
| 373 |
}; |
| 374 |
|
| 375 |
&pcie1_phy { |
| 376 |
vdda-phy-supply = <&vreg_l10c_0p88>; |
| 377 |
vdda-pll-supply = <&vreg_l6b_1p2>; |
| 378 |
}; |
| 379 |
|
| 380 |
&pm8350c_pwm { |
| 381 |
pinctrl-names = "default"; |
| 382 |
pinctrl-0 = <&pmic_edp_bl_pwm>; |
| 383 |
}; |
| 384 |
|
| 385 |
&pmk8350_vadc { |
| 386 |
channel@3 { |
| 387 |
reg = <PMK8350_ADC7_DIE_TEMP>; |
| 388 |
label = "pmk8350_die_temp"; |
| 389 |
qcom,pre-scaling = <1 1>; |
| 390 |
}; |
| 391 |
|
| 392 |
channel@403 { |
| 393 |
reg = <PMR735A_ADC7_DIE_TEMP>; |
| 394 |
label = "pmr735a_die_temp"; |
| 395 |
qcom,pre-scaling = <1 1>; |
| 396 |
}; |
| 397 |
}; |
| 398 |
|
| 399 |
&qfprom { |
| 400 |
vcc-supply = <&vdd_qfprom>; |
| 401 |
}; |
| 402 |
|
| 403 |
/* For eMMC. NOTE: not all Qcards have eMMC stuffed */ |
| 404 |
&sdhc_1 { |
| 405 |
vmmc-supply = <&vreg_l7b_2p5>; |
| 406 |
vqmmc-supply = <&vreg_l19b_1p8>; |
| 407 |
|
| 408 |
non-removable; |
| 409 |
no-sd; |
| 410 |
no-sdio; |
| 411 |
}; |
| 412 |
|
| 413 |
&swr0 { |
| 414 |
wcd_rx: codec@0,4 { |
| 415 |
compatible = "sdw20217010d00"; |
| 416 |
reg = <0 4>; |
| 417 |
qcom,rx-port-mapping = <1 2 3 4 5>; |
| 418 |
}; |
| 419 |
}; |
| 420 |
|
| 421 |
&swr1 { |
| 422 |
wcd_tx: codec@0,3 { |
| 423 |
compatible = "sdw20217010d00"; |
| 424 |
reg = <0 3>; |
| 425 |
qcom,tx-port-mapping = <1 2 3 4>; |
| 426 |
}; |
| 427 |
}; |
| 428 |
|
| 429 |
uart_dbg: &uart5 { |
| 430 |
status = "okay"; |
| 431 |
}; |
| 432 |
|
| 433 |
mos_bt_uart: &uart7 { |
| 434 |
status = "okay"; |
| 435 |
|
| 436 |
/delete-property/ interrupts; |
| 437 |
interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>, |
| 438 |
<&tlmm 31 IRQ_TYPE_EDGE_FALLING>; |
| 439 |
pinctrl-names = "default", "sleep"; |
| 440 |
pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>; |
| 441 |
|
| 442 |
bluetooth: bluetooth { |
| 443 |
compatible = "qcom,wcn6750-bt"; |
| 444 |
pinctrl-names = "default"; |
| 445 |
pinctrl-0 = <&mos_bt_en>; |
| 446 |
enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>; |
| 447 |
swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>; |
| 448 |
vddaon-supply = <&vreg_s7b_0p952>; |
| 449 |
vddbtcxmx-supply = <&vreg_s7b_0p952>; |
| 450 |
vddrfacmn-supply = <&vreg_s7b_0p952>; |
| 451 |
vddrfa0p8-supply = <&vreg_s7b_0p952>; |
| 452 |
vddrfa1p7-supply = <&vdd19_pmu_rfa_i>; |
| 453 |
vddrfa1p2-supply = <&vdd13_pmu_rfa_i>; |
| 454 |
vddrfa2p2-supply = <&vreg_s1c_2p2>; |
| 455 |
vddasd-supply = <&vreg_l11c_2p8>; |
| 456 |
vddio-supply = <&vreg_l18b_1p8>; |
| 457 |
max-speed = <3200000>; |
| 458 |
}; |
| 459 |
}; |
| 460 |
|
| 461 |
&usb_1_hsphy { |
| 462 |
vdda-pll-supply = <&vdd_a_usbhs_core>; |
| 463 |
vdda33-supply = <&vdd_a_usbhs_3p1>; |
| 464 |
vdda18-supply = <&vdd_a_usbhs_1p8>; |
| 465 |
}; |
| 466 |
|
| 467 |
&usb_1_qmpphy { |
| 468 |
vdda-phy-supply = <&vdd_a_usbssdp_0_1p2>; |
| 469 |
vdda-pll-supply = <&vdd_a_usbssdp_0_core>; |
| 470 |
}; |
| 471 |
|
| 472 |
&usb_2_hsphy { |
| 473 |
vdda-pll-supply = <&vdd_a_usbhs_core>; |
| 474 |
vdda33-supply = <&vdd_a_usbhs_3p1>; |
| 475 |
vdda18-supply = <&vdd_a_usbhs_1p8>; |
| 476 |
}; |
| 477 |
|
| 478 |
/* |
| 479 |
* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES |
| 480 |
* |
| 481 |
* NOTE: In general if pins leave the Qcard then the pinctrl goes in the |
| 482 |
* baseboard or board device tree, not here. |
| 483 |
*/ |
| 484 |
|
| 485 |
/* No external pull for eDP HPD, so set the internal one. */ |
| 486 |
&edp_hot_plug_det { |
| 487 |
bias-pull-down; |
| 488 |
}; |
| 489 |
|
| 490 |
/* |
| 491 |
* For ts_i2c |
| 492 |
* |
| 493 |
* Technically this i2c bus actually leaves the Qcard, but it leaves directly |
| 494 |
* via the eDP connector (it doesn't hit the baseboard). The external pulls |
| 495 |
* are on Qcard. |
| 496 |
*/ |
| 497 |
&qup_i2c13_data_clk { |
| 498 |
/* Has external pull */ |
| 499 |
bias-disable; |
| 500 |
drive-strength = <2>; |
| 501 |
}; |
| 502 |
|
| 503 |
/* For mos_bt_uart */ |
| 504 |
&qup_uart7_cts { |
| 505 |
/* |
| 506 |
* Configure a bias-bus-hold on CTS to lower power |
| 507 |
* usage when Bluetooth is turned off. Bus hold will |
| 508 |
* maintain a low power state regardless of whether |
| 509 |
* the Bluetooth module drives the pin in either |
| 510 |
* direction or leaves the pin fully unpowered. |
| 511 |
*/ |
| 512 |
bias-bus-hold; |
| 513 |
}; |
| 514 |
|
| 515 |
/* For mos_bt_uart */ |
| 516 |
&qup_uart7_rts { |
| 517 |
/* We'll drive RTS, so no pull */ |
| 518 |
bias-disable; |
| 519 |
drive-strength = <2>; |
| 520 |
}; |
| 521 |
|
| 522 |
/* For mos_bt_uart */ |
| 523 |
&qup_uart7_tx { |
| 524 |
/* We'll drive TX, so no pull */ |
| 525 |
bias-disable; |
| 526 |
drive-strength = <2>; |
| 527 |
}; |
| 528 |
|
| 529 |
/* For mos_bt_uart */ |
| 530 |
&qup_uart7_rx { |
| 531 |
/* |
| 532 |
* Configure a pull-up on RX. This is needed to avoid |
| 533 |
* garbage data when the TX pin of the Bluetooth module is |
| 534 |
* in tri-state (module powered off or not driving the |
| 535 |
* signal yet). |
| 536 |
*/ |
| 537 |
bias-pull-up; |
| 538 |
}; |
| 539 |
|
| 540 |
/* eMMC, if stuffed, is straight on the Qcard */ |
| 541 |
&sdc1_clk { |
| 542 |
bias-disable; |
| 543 |
drive-strength = <16>; |
| 544 |
}; |
| 545 |
|
| 546 |
&sdc1_cmd { |
| 547 |
bias-pull-up; |
| 548 |
drive-strength = <10>; |
| 549 |
}; |
| 550 |
|
| 551 |
&sdc1_data { |
| 552 |
bias-pull-up; |
| 553 |
drive-strength = <10>; |
| 554 |
}; |
| 555 |
|
| 556 |
&sdc1_rclk { |
| 557 |
bias-pull-down; |
| 558 |
}; |
| 559 |
|
| 560 |
/* |
| 561 |
* PINCTRL - QCARD |
| 562 |
* |
| 563 |
* This has entries that are defined by Qcard even if they go to the main |
| 564 |
* board. In cases where the pulls may be board dependent we defer those |
| 565 |
* settings to the board device tree. Drive strengths tend to be assinged here |
| 566 |
* but could conceivably be overwridden by board device trees. |
| 567 |
*/ |
| 568 |
|
| 569 |
&pm8350c_gpios { |
| 570 |
pmic_edp_bl_en: pmic-edp-bl-en-state { |
| 571 |
pins = "gpio7"; |
| 572 |
function = "normal"; |
| 573 |
bias-disable; |
| 574 |
qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; |
| 575 |
|
| 576 |
/* Force backlight to be disabled to match state at boot. */ |
| 577 |
output-low; |
| 578 |
}; |
| 579 |
|
| 580 |
pmic_edp_bl_pwm: pmic-edp-bl-pwm-state { |
| 581 |
pins = "gpio8"; |
| 582 |
function = "func1"; |
| 583 |
bias-disable; |
| 584 |
qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>; |
| 585 |
output-low; |
| 586 |
power-source = <0>; |
| 587 |
}; |
| 588 |
}; |
| 589 |
|
| 590 |
&tlmm { |
| 591 |
mos_bt_en: mos-bt-en-state { |
| 592 |
pins = "gpio85"; |
| 593 |
function = "gpio"; |
| 594 |
drive-strength = <2>; |
| 595 |
output-low; |
| 596 |
}; |
| 597 |
|
| 598 |
/* For mos_bt_uart */ |
| 599 |
qup_uart7_sleep_cts: qup-uart7-sleep-cts-state { |
| 600 |
pins = "gpio28"; |
| 601 |
function = "gpio"; |
| 602 |
/* |
| 603 |
* Configure a bias-bus-hold on CTS to lower power |
| 604 |
* usage when Bluetooth is turned off. Bus hold will |
| 605 |
* maintain a low power state regardless of whether |
| 606 |
* the Bluetooth module drives the pin in either |
| 607 |
* direction or leaves the pin fully unpowered. |
| 608 |
*/ |
| 609 |
bias-bus-hold; |
| 610 |
}; |
| 611 |
|
| 612 |
/* For mos_bt_uart */ |
| 613 |
qup_uart7_sleep_rts: qup-uart7-sleep-rts-state { |
| 614 |
pins = "gpio29"; |
| 615 |
function = "gpio"; |
| 616 |
/* |
| 617 |
* Configure pull-down on RTS. As RTS is active low |
| 618 |
* signal, pull it low to indicate the BT SoC that it |
| 619 |
* can wakeup the system anytime from suspend state by |
| 620 |
* pulling RX low (by sending wakeup bytes). |
| 621 |
*/ |
| 622 |
bias-pull-down; |
| 623 |
}; |
| 624 |
|
| 625 |
/* For mos_bt_uart */ |
| 626 |
qup_uart7_sleep_rx: qup-uart7-sleep-rx-state { |
| 627 |
pins = "gpio31"; |
| 628 |
function = "gpio"; |
| 629 |
/* |
| 630 |
* Configure a pull-up on RX. This is needed to avoid |
| 631 |
* garbage data when the TX pin of the Bluetooth module |
| 632 |
* is floating which may cause spurious wakeups. |
| 633 |
*/ |
| 634 |
bias-pull-up; |
| 635 |
}; |
| 636 |
|
| 637 |
/* For mos_bt_uart */ |
| 638 |
qup_uart7_sleep_tx: qup-uart7-sleep-tx-state { |
| 639 |
pins = "gpio30"; |
| 640 |
function = "gpio"; |
| 641 |
/* |
| 642 |
* Configure pull-up on TX when it isn't actively driven |
| 643 |
* to prevent BT SoC from receiving garbage during sleep. |
| 644 |
*/ |
| 645 |
bias-pull-up; |
| 646 |
}; |
| 647 |
|
| 648 |
ts_int_conn: ts-int-conn-state { |
| 649 |
pins = "gpio55"; |
| 650 |
function = "gpio"; |
| 651 |
bias-pull-up; |
| 652 |
}; |
| 653 |
|
| 654 |
ts_rst_conn: ts-rst-conn-state { |
| 655 |
pins = "gpio54"; |
| 656 |
function = "gpio"; |
| 657 |
drive-strength = <2>; |
| 658 |
}; |
| 659 |
|
| 660 |
us_euro_hs_sel: us-euro-hs-sel-state { |
| 661 |
pins = "gpio81"; |
| 662 |
function = "gpio"; |
| 663 |
bias-pull-down; |
| 664 |
drive-strength = <2>; |
| 665 |
}; |
| 666 |
|
| 667 |
wcd_reset_n: wcd-reset-n-state { |
| 668 |
pins = "gpio83"; |
| 669 |
function = "gpio"; |
| 670 |
drive-strength = <8>; |
| 671 |
}; |
| 672 |
|
| 673 |
wcd_reset_n_sleep: wcd-reset-n-sleep-state { |
| 674 |
pins = "gpio83"; |
| 675 |
function = "gpio"; |
| 676 |
drive-strength = <8>; |
| 677 |
bias-disable; |
| 678 |
}; |
| 679 |
}; |