Debian Codegraph @

scripts/dtc/include-prefixes/arm64/qcom/sc7280-herobrine.dtsi

raw
1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2 /*
3 * Google Herobrine baseboard device tree source
4 *
5 * The set of things in this file is a bit loosely defined. It's roughly
6 * defined as the set of things that the child boards happen to have in
7 * common. Since all of the child boards started from the same original
8 * design this is hopefully a large set of things but as more derivatives
9 * appear things may "bubble down" out of this file. For things that are
10 * part of the reference design but might not exist on child nodes we will
11 * follow the lead of the SoC dtsi files and leave their status as "disabled".
12 *
13 * Copyright 2022 Google LLC.
14 */
15
16 #include <dt-bindings/input/gpio-keys.h>
17 #include <dt-bindings/input/input.h>
18 #include <dt-bindings/leds/common.h>
19
20 #include "sc7280-qcard.dtsi"
21 #include "sc7280-chrome-common.dtsi"
22
23 / {
24 chosen {
25 stdout-path = "serial0:115200n8";
26 };
27
28 /*
29 * FIXED REGULATORS
30 *
31 * Sort order:
32 * 1. parents above children.
33 * 2. higher voltage above lower voltage.
34 * 3. alphabetically by node name.
35 */
36
37 /* This is the top level supply and variable voltage */
38 ppvar_sys: ppvar-sys-regulator {
39 compatible = "regulator-fixed";
40 regulator-name = "ppvar_sys";
41 regulator-always-on;
42 regulator-boot-on;
43 };
44
45 /* This divides ppvar_sys by 2, so voltage is variable */
46 src_vph_pwr: src-vph-pwr-regulator {
47 compatible = "regulator-fixed";
48 regulator-name = "src_vph_pwr";
49
50 /* EC turns on with switchcap_on; always on for AP */
51 regulator-always-on;
52 regulator-boot-on;
53
54 vin-supply = <&ppvar_sys>;
55 };
56
57 pp5000_s5: pp5000-s5-regulator {
58 compatible = "regulator-fixed";
59 regulator-name = "pp5000_s5";
60
61 /* EC turns on with en_pp5000_s5; always on for AP */
62 regulator-always-on;
63 regulator-boot-on;
64 regulator-min-microvolt = <5000000>;
65 regulator-max-microvolt = <5000000>;
66
67 vin-supply = <&ppvar_sys>;
68 };
69
70 pp3300_z1: pp3300-z1-regulator {
71 compatible = "regulator-fixed";
72 regulator-name = "pp3300_z1";
73
74 /* EC turns on with en_pp3300_z1; always on for AP */
75 regulator-always-on;
76 regulator-boot-on;
77 regulator-min-microvolt = <3300000>;
78 regulator-max-microvolt = <3300000>;
79
80 vin-supply = <&ppvar_sys>;
81 };
82
83 pp3300_codec: pp3300-codec-regulator {
84 compatible = "regulator-fixed";
85 regulator-name = "pp3300_codec";
86
87 regulator-min-microvolt = <3300000>;
88 regulator-max-microvolt = <3300000>;
89
90 gpio = <&tlmm 105 GPIO_ACTIVE_HIGH>;
91 enable-active-high;
92 pinctrl-names = "default";
93 pinctrl-0 = <&en_pp3300_codec>;
94
95 vin-supply = <&pp3300_z1>;
96 status = "disabled";
97 };
98
99 pp3300_left_in_mlb: pp3300-left-in-mlb-regulator {
100 compatible = "regulator-fixed";
101 regulator-name = "pp3300_left_in_mlb";
102
103 regulator-min-microvolt = <3300000>;
104 regulator-max-microvolt = <3300000>;
105
106 gpio = <&tlmm 80 GPIO_ACTIVE_HIGH>;
107 enable-active-high;
108 pinctrl-names = "default";
109 pinctrl-0 = <&en_pp3300_dx_edp>;
110
111 regulator-enable-ramp-delay = <3000>;
112
113 /*
114 * eDP panel specs nearly always have a spec that says you
115 * shouldn't turn them off an on again without waiting 500ms.
116 * Add this as a board constraint since this rail is shared
117 * between the panel and touchscreen.
118 */
119 off-on-delay-us = <500000>;
120
121 /*
122 * Stat the regulator on. This has the advantage of starting
123 * the slow process of powering the panel on as soon as we
124 * probe the regulator. It also avoids tripping the
125 * off-on-delay immediately on every bootup.
126 */
127 regulator-boot-on;
128
129 vin-supply = <&pp3300_z1>;
130 };
131
132 pp3300_mcu_fp:
133 pp3300_fp_ls:
134 pp3300_fp_mcu: pp3300-fp-regulator {
135 compatible = "regulator-fixed";
136 regulator-name = "pp3300_fp";
137
138 regulator-min-microvolt = <3300000>;
139 regulator-max-microvolt = <3300000>;
140
141 regulator-boot-on;
142 regulator-always-on;
143
144 /*
145 * WARNING: it is intentional that GPIO 77 isn't listed here.
146 * The userspace script for updating the fingerprint firmware
147 * needs to control the FP regulators during a FW update,
148 * hence the signal can't be owned by the kernel regulator.
149 */
150
151 pinctrl-names = "default";
152 pinctrl-0 = <&en_fp_rails>;
153
154 vin-supply = <&pp3300_z1>;
155 status = "disabled";
156 };
157
158 pp3300_hub: pp3300-hub-regulator {
159 compatible = "regulator-fixed";
160 regulator-name = "pp3300_hub";
161
162 regulator-min-microvolt = <3300000>;
163 regulator-max-microvolt = <3300000>;
164
165 /* The BIOS leaves this regulator on */
166 regulator-boot-on;
167
168 gpio = <&tlmm 157 GPIO_ACTIVE_HIGH>;
169 enable-active-high;
170 pinctrl-names = "default";
171 pinctrl-0 = <&hub_en>;
172
173 vin-supply = <&pp3300_z1>;
174 };
175
176 pp3300_tp: pp3300-tp-regulator {
177 compatible = "regulator-fixed";
178 regulator-name = "pp3300_tp";
179
180 regulator-min-microvolt = <3300000>;
181 regulator-max-microvolt = <3300000>;
182
183 /* AP turns on with PP1800_L18B_S0; always on for AP */
184 regulator-always-on;
185 regulator-boot-on;
186
187 vin-supply = <&pp3300_z1>;
188 };
189
190 pp3300_ssd: pp3300-ssd-regulator {
191 compatible = "regulator-fixed";
192 regulator-name = "pp3300_ssd";
193
194 regulator-min-microvolt = <3300000>;
195 regulator-max-microvolt = <3300000>;
196
197 gpio = <&tlmm 51 GPIO_ACTIVE_HIGH>;
198 enable-active-high;
199 pinctrl-names = "default";
200 pinctrl-0 = <&ssd_en>;
201
202 /*
203 * The bootloaer may have left PCIe configured. Powering this
204 * off while the PCIe clocks are still running isn't great,
205 * so it's better to default to this regulator being on.
206 */
207 regulator-boot-on;
208
209 vin-supply = <&pp3300_z1>;
210 };
211
212 pp2850_vcm_wf_cam: pp2850-vcm-wf-cam-regulator {
213 compatible = "regulator-fixed";
214 regulator-name = "pp2850_vcm_wf_cam";
215
216 regulator-min-microvolt = <2850000>;
217 regulator-max-microvolt = <2850000>;
218
219 gpio = <&tlmm 119 GPIO_ACTIVE_HIGH>;
220 enable-active-high;
221 pinctrl-names = "default";
222 pinctrl-0 = <&wf_cam_en>;
223
224 vin-supply = <&pp3300_z1>;
225 status = "disabled";
226 };
227
228 pp2850_wf_cam: pp2850-wf-cam-regulator {
229 compatible = "regulator-fixed";
230 regulator-name = "pp2850_wf_cam";
231
232 regulator-min-microvolt = <2850000>;
233 regulator-max-microvolt = <2850000>;
234
235 gpio = <&tlmm 119 GPIO_ACTIVE_HIGH>;
236 enable-active-high;
237 /*
238 * The pinconf can only be referenced once so we put it on the
239 * first regulator and comment it out here.
240 *
241 * pinctrl-names = "default";
242 * pinctrl-0 = <&wf_cam_en>;
243 */
244
245 vin-supply = <&pp3300_z1>;
246 status = "disabled";
247 };
248
249 pp1800_fp: pp1800-fp-regulator {
250 compatible = "regulator-fixed";
251 regulator-name = "pp1800_fp";
252
253 regulator-min-microvolt = <1800000>;
254 regulator-max-microvolt = <1800000>;
255
256 regulator-boot-on;
257 regulator-always-on;
258
259 /*
260 * WARNING: it is intentional that GPIO 77 isn't listed here.
261 * The userspace script for updating the fingerprint firmware
262 * needs to control the FP regulators during a FW update,
263 * hence the signal can't be owned by the kernel regulator.
264 */
265
266 pinctrl-names = "default";
267 pinctrl-0 = <&en_fp_rails>;
268
269 vin-supply = <&pp1800_l18b_s0>;
270 status = "disabled";
271 };
272
273 pp1800_wf_cam: pp1800-wf-cam-regulator {
274 compatible = "regulator-fixed";
275 regulator-name = "pp1800_wf_cam";
276
277 regulator-min-microvolt = <1800000>;
278 regulator-max-microvolt = <1800000>;
279
280 gpio = <&tlmm 119 GPIO_ACTIVE_HIGH>;
281 enable-active-high;
282 /*
283 * The pinconf can only be referenced once so we put it on the
284 * first regulator and comment it out here.
285 *
286 * pinctrl-names = "default";
287 * pinctrl-0 = <&wf_cam_en>;
288 */
289
290 vin-supply = <&vreg_l19b_s0>;
291 status = "disabled";
292 };
293
294 pp1200_wf_cam: pp1200-wf-cam-regulator {
295 compatible = "regulator-fixed";
296 regulator-name = "pp1200_wf_cam";
297
298 regulator-min-microvolt = <1200000>;
299 regulator-max-microvolt = <1200000>;
300
301 gpio = <&tlmm 119 GPIO_ACTIVE_HIGH>;
302 enable-active-high;
303 /*
304 * The pinconf can only be referenced once so we put it on the
305 * first regulator and comment it out here.
306 *
307 * pinctrl-names = "default";
308 * pinctrl-0 = <&wf_cam_en>;
309 */
310
311 vin-supply = <&pp3300_z1>;
312 status = "disabled";
313 };
314
315 /* BOARD-SPECIFIC TOP LEVEL NODES */
316
317 max98360a: audio-codec-0 {
318 compatible = "maxim,max98360a";
319 pinctrl-names = "default";
320 pinctrl-0 = <&amp_en>;
321 sdmode-gpios = <&tlmm 63 GPIO_ACTIVE_HIGH>;
322 #sound-dai-cells = <0>;
323 };
324
325 pwmleds: pwmleds {
326 compatible = "pwm-leds";
327 status = "disabled";
328 keyboard_backlight: led-0 {
329 label = "cros_ec::kbd_backlight";
330 function = LED_FUNCTION_KBD_BACKLIGHT;
331 pwms = <&cros_ec_pwm 0>;
332 max-brightness = <1023>;
333 };
334 };
335 };
336
337 /*
338 * ADJUSTMENTS TO QCARD REGULATORS
339 *
340 * Mostly this is just board-local names for regulators that come from
341 * Qcard, but this also has some minor regulator overrides.
342 *
343 * Names are only listed here if regulators go somewhere other than a
344 * testpoint.
345 */
346
347 /* From Qcard to our board; ordered by PMIC-ID / rail number */
348
349 pp1256_s8b: &vreg_s8b_1p256 {};
350
351 pp1800_l18b_s0: &vreg_l18b_1p8 {};
352 pp1800_l18b: &vreg_l18b_1p8 {};
353
354 vreg_l19b_s0: &vreg_l19b_1p8 {};
355
356 pp1800_alc5682: &vreg_l2c_1p8 {};
357 pp1800_l2c: &vreg_l2c_1p8 {};
358
359 vreg_l4c: &vreg_l4c_1p8_3p0 {};
360
361 ppvar_l6c: &vreg_l6c_2p96 {};
362
363 pp3000_l7c: &vreg_l7c_3p0 {};
364
365 pp1800_prox: &vreg_l8c_1p8 {};
366 pp1800_l8c: &vreg_l8c_1p8 {};
367
368 pp2950_l9c: &vreg_l9c_2p96 {};
369
370 pp1800_lcm: &vreg_l12c_1p8 {};
371 pp1800_mipi: &vreg_l12c_1p8 {};
372 pp1800_l12c: &vreg_l12c_1p8 {};
373
374 pp3300_lcm: &vreg_l13c_3p0 {};
375 pp3300_mipi: &vreg_l13c_3p0 {};
376 pp3300_l13c: &vreg_l13c_3p0 {};
377
378 /* From our board to Qcard; ordered same as node definition above */
379
380 vreg_edp_bl: &ppvar_sys {};
381
382 ts_avdd: &pp3300_left_in_mlb {};
383 vreg_edp_3p3: &pp3300_left_in_mlb {};
384
385 /* Regulator overrides from Qcard */
386
387 /*
388 * Herobrine boards only use l2c to power an external audio codec (like
389 * alc5682) and we want that to be at 1.8V, not at some slightly lower voltage.
390 */
391 &vreg_l2c_1p8 {
392 regulator-min-microvolt = <1800000>;
393 };
394
395 /* ADDITIONS TO NODES DEFINED IN PARENT DEVICE TREE FILES */
396
397 &edp_panel {
398 /* Our board provides power to the qcard for the eDP panel. */
399 power-supply = <&vreg_edp_3p3>;
400 };
401
402 ap_sar_sensor_i2c: &i2c1 {
403 clock-frequency = <400000>;
404 status = "disabled";
405
406 ap_sar_sensor0: proximity@28 {
407 compatible = "semtech,sx9324";
408 reg = <0x28>;
409 #io-channel-cells = <1>;
410 pinctrl-names = "default";
411 pinctrl-0 = <&sar0_irq_odl>;
412
413 interrupt-parent = <&tlmm>;
414 interrupts = <141 IRQ_TYPE_LEVEL_LOW>;
415
416 vdd-supply = <&pp1800_prox>;
417
418 label = "proximity-wifi_cellular-0";
419 status = "disabled";
420 };
421
422 ap_sar_sensor1: proximity@2c {
423 compatible = "semtech,sx9324";
424 reg = <0x2c>;
425 #io-channel-cells = <1>;
426 pinctrl-names = "default";
427 pinctrl-0 = <&sar1_irq_odl>;
428
429 interrupt-parent = <&tlmm>;
430 interrupts = <140 IRQ_TYPE_LEVEL_LOW>;
431
432 vdd-supply = <&pp1800_prox>;
433
434 label = "proximity-wifi_cellular-1";
435 status = "disabled";
436 };
437 };
438
439 ap_i2c_tpm: &i2c14 {
440 status = "okay";
441 clock-frequency = <400000>;
442
443 tpm@50 {
444 compatible = "google,cr50";
445 reg = <0x50>;
446
447 pinctrl-names = "default";
448 pinctrl-0 = <&gsc_ap_int_odl>;
449
450 interrupt-parent = <&tlmm>;
451 interrupts = <104 IRQ_TYPE_EDGE_RISING>;
452 };
453 };
454
455 &mdss {
456 status = "okay";
457 };
458
459 &mdss_dp {
460 status = "okay";
461 pinctrl-names = "default";
462 pinctrl-0 = <&dp_hot_plug_det>;
463 };
464
465 &mdss_dp_out {
466 data-lanes = <0 1>;
467 link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000>;
468 };
469
470 /* NVMe drive, enabled on a per-board basis */
471 &pcie1 {
472 pinctrl-names = "default";
473 pinctrl-0 = <&pcie1_clkreq_n>, <&ssd_rst_l>, <&pe_wake_odl>;
474
475 perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
476 vddpe-3v3-supply = <&pp3300_ssd>;
477 };
478
479 &pm8350c_pwm {
480 status = "okay";
481 };
482
483 &pm8350c_pwm_backlight {
484 status = "okay";
485
486 /* Our board provides power to the qcard for the backlight */
487 power-supply = <&vreg_edp_bl>;
488 };
489
490 &pmk8350_rtc {
491 status = "disabled";
492 };
493
494 &qupv3_id_0 {
495 status = "okay";
496 };
497
498 &qupv3_id_1 {
499 status = "okay";
500 };
501
502 /* SD Card, enabled on a per-board basis */
503 &sdhc_2 {
504 pinctrl-0 = <&sdc2_clk>, <&sdc2_cmd>, <&sdc2_data>, <&sd_cd_odl>;
505 pinctrl-1 = <&sdc2_clk_sleep>, <&sdc2_cmd_sleep>, <&sdc2_data_sleep>, <&sd_cd_odl>;
506
507 vmmc-supply = <&pp2950_l9c>;
508 vqmmc-supply = <&ppvar_l6c>;
509
510 cd-gpios = <&tlmm 91 GPIO_ACTIVE_LOW>;
511 };
512
513 &spi_flash {
514 spi-max-frequency = <50000000>;
515 };
516
517 /* Fingerprint, enabled on a per-board basis */
518 ap_spi_fp: &spi9 {
519 pinctrl-0 = <&qup_spi9_data_clk>, <&qup_spi9_cs_gpio_init_high>, <&qup_spi9_cs_gpio>;
520
521 cs-gpios = <&tlmm 39 GPIO_ACTIVE_LOW>;
522
523 cros_ec_fp: ec@0 {
524 compatible = "google,cros-ec-fp", "google,cros-ec-spi";
525 reg = <0>;
526 interrupt-parent = <&tlmm>;
527 interrupts = <61 IRQ_TYPE_LEVEL_LOW>;
528 pinctrl-names = "default";
529 pinctrl-0 = <&fp_to_ap_irq_l>, <&fp_rst_l>, <&fpmcu_boot0>;
530 boot0-gpios = <&tlmm 68 GPIO_ACTIVE_HIGH>;
531 reset-gpios = <&tlmm 78 GPIO_ACTIVE_LOW>;
532 spi-max-frequency = <3000000>;
533 vdd-supply = <&pp3300_fp_mcu>;
534 };
535 };
536
537 ap_ec_spi: &spi10 {
538 status = "okay";
539 pinctrl-0 = <&qup_spi10_data_clk>, <&qup_spi10_cs_gpio_init_high>, <&qup_spi10_cs_gpio>;
540
541 cs-gpios = <&tlmm 43 GPIO_ACTIVE_LOW>;
542
543 cros_ec: ec@0 {
544 compatible = "google,cros-ec-spi";
545 reg = <0>;
546 interrupt-parent = <&tlmm>;
547 interrupts = <18 IRQ_TYPE_LEVEL_LOW>;
548 pinctrl-names = "default";
549 pinctrl-0 = <&ap_ec_int_l>;
550 spi-max-frequency = <3000000>;
551 wakeup-source;
552
553 cros_ec_pwm: pwm {
554 compatible = "google,cros-ec-pwm";
555 #pwm-cells = <1>;
556 };
557
558 i2c_tunnel: i2c-tunnel {
559 compatible = "google,cros-ec-i2c-tunnel";
560 google,remote-bus = <0>;
561 #address-cells = <1>;
562 #size-cells = <0>;
563 };
564
565 typec {
566 compatible = "google,cros-ec-typec";
567 #address-cells = <1>;
568 #size-cells = <0>;
569
570 usb_c0: connector@0 {
571 compatible = "usb-c-connector";
572 reg = <0>;
573 label = "left";
574 power-role = "dual";
575 data-role = "host";
576 try-power-role = "source";
577 };
578
579 usb_c1: connector@1 {
580 compatible = "usb-c-connector";
581 reg = <1>;
582 label = "right";
583 power-role = "dual";
584 data-role = "host";
585 try-power-role = "source";
586 };
587 };
588 };
589 };
590
591 #include <arm/cros-ec-keyboard.dtsi>
592 #include <arm/cros-ec-sbs.dtsi>
593
594 &keyboard_controller {
595 function-row-physmap = <
596 MATRIX_KEY(0x00, 0x02, 0) /* T1 */
597 MATRIX_KEY(0x03, 0x02, 0) /* T2 */
598 MATRIX_KEY(0x02, 0x02, 0) /* T3 */
599 MATRIX_KEY(0x01, 0x02, 0) /* T4 */
600 MATRIX_KEY(0x03, 0x04, 0) /* T5 */
601 MATRIX_KEY(0x02, 0x04, 0) /* T6 */
602 MATRIX_KEY(0x01, 0x04, 0) /* T7 */
603 MATRIX_KEY(0x02, 0x09, 0) /* T8 */
604 MATRIX_KEY(0x01, 0x09, 0) /* T9 */
605 MATRIX_KEY(0x00, 0x04, 0) /* T10 */
606 >;
607 linux,keymap = <
608 MATRIX_KEY(0x00, 0x02, KEY_BACK)
609 MATRIX_KEY(0x03, 0x02, KEY_REFRESH)
610 MATRIX_KEY(0x02, 0x02, KEY_ZOOM)
611 MATRIX_KEY(0x01, 0x02, KEY_SCALE)
612 MATRIX_KEY(0x03, 0x04, KEY_SYSRQ)
613 MATRIX_KEY(0x02, 0x04, KEY_BRIGHTNESSDOWN)
614 MATRIX_KEY(0x01, 0x04, KEY_BRIGHTNESSUP)
615 MATRIX_KEY(0x02, 0x09, KEY_MUTE)
616 MATRIX_KEY(0x01, 0x09, KEY_VOLUMEDOWN)
617 MATRIX_KEY(0x00, 0x04, KEY_VOLUMEUP)
618
619 CROS_STD_MAIN_KEYMAP
620 >;
621 };
622
623 &usb_1 {
624 dr_mode = "host";
625
626 #address-cells = <1>;
627 #size-cells = <0>;
628
629 status = "okay";
630
631 /* 2.x hub on port 1 */
632 usb_hub_2_x: hub@1 {
633 compatible = "usbbda,5411";
634 reg = <1>;
635 vdd-supply = <&pp3300_hub>;
636 peer-hub = <&usb_hub_3_x>;
637 };
638
639 /* 3.x hub on port 2 */
640 usb_hub_3_x: hub@2 {
641 compatible = "usbbda,411";
642 reg = <2>;
643 vdd-supply = <&pp3300_hub>;
644 peer-hub = <&usb_hub_2_x>;
645 };
646 };
647
648 &usb_1_hsphy {
649 status = "okay";
650
651 qcom,hs-rise-fall-time-bp = <0>;
652 qcom,squelch-detector-bp = <(-2090)>;
653 qcom,hs-disconnect-bp = <1743>;
654 qcom,hs-amplitude-bp = <1780>;
655 qcom,hs-crossover-voltage-microvolt = <(-31000)>;
656 qcom,hs-output-impedance-micro-ohms = <2600000>;
657 };
658
659 &usb_1_qmpphy {
660 status = "okay";
661 };
662
663 /* PINCTRL - ADDITIONS TO NODES IN PARENT DEVICE TREE FILES */
664
665 &dp_hot_plug_det {
666 bias-disable;
667 };
668
669 &mi2s1_data0 {
670 drive-strength = <6>;
671 bias-disable;
672 };
673
674 &mi2s1_sclk {
675 drive-strength = <6>;
676 bias-disable;
677 };
678
679 &mi2s1_ws {
680 drive-strength = <6>;
681 bias-disable;
682 };
683
684 &pcie1_clkreq_n {
685 bias-pull-up;
686 drive-strength = <2>;
687 };
688
689 &qspi_cs0 {
690 bias-disable; /* External pullup */
691 drive-strength = <8>;
692 };
693
694 &qspi_clk {
695 bias-pull-down; /* No external pulls */
696 drive-strength = <8>;
697 };
698
699 &qspi_data0 {
700 bias-pull-down; /* No external pulls */
701 drive-strength = <8>;
702 };
703
704 &qspi_data1 {
705 bias-disable; /* External pulldown */
706 drive-strength = <8>;
707 };
708
709 /* For ap_tp_i2c */
710 &qup_i2c0_data_clk {
711 /* Has external pull */
712 bias-disable;
713 drive-strength = <2>;
714 };
715
716 /* For ap_i2c_tpm */
717 &qup_i2c14_data_clk {
718 /* Has external pull */
719 bias-disable;
720 drive-strength = <2>;
721 };
722
723 /* For ap_spi_fp */
724 &qup_spi9_data_clk {
725 bias-disable;
726 drive-strength = <2>;
727 };
728
729 /* For ap_spi_fp */
730 &qup_spi9_cs_gpio {
731 bias-disable;
732 drive-strength = <2>;
733 };
734
735 /* For ap_ec_spi */
736 &qup_spi10_data_clk {
737 bias-disable;
738 drive-strength = <2>;
739 };
740
741 /* For ap_ec_spi */
742 &qup_spi10_cs_gpio {
743 bias-disable;
744 drive-strength = <2>;
745 };
746
747 /* For uart_dbg */
748 &qup_uart5_rx {
749 bias-pull-up;
750 };
751
752 /* For uart_dbg */
753 &qup_uart5_tx {
754 bias-disable;
755 drive-strength = <2>;
756 };
757
758 &sdc2_clk {
759 bias-disable;
760 drive-strength = <16>;
761 };
762
763 &sdc2_cmd {
764 bias-pull-up;
765 drive-strength = <10>;
766 };
767
768 &sdc2_data {
769 bias-pull-up;
770 drive-strength = <10>;
771 };
772
773 /* PINCTRL - board-specific pinctrl */
774
775 &pm7325_gpios {
776 /*
777 * On a quick glance it might look like KYPD_VOL_UP_N is used, but
778 * that only passes through to a debug connector and not to the actual
779 * volume up key.
780 */
781 status = "disabled"; /* No GPIOs are connected */
782 };
783
784 &pmk8350_gpios {
785 status = "disabled"; /* No GPIOs are connected */
786 };
787
788 &tlmm {
789 /* pinctrl settings for pins that have no real owners. */
790 pinctrl-names = "default";
791 pinctrl-0 = <&bios_flash_wp_od>;
792
793 amp_en: amp-en-state {
794 pins = "gpio63";
795 function = "gpio";
796 bias-disable;
797 drive-strength = <2>;
798 };
799
800 ap_ec_int_l: ap-ec-int-l-state {
801 pins = "gpio18";
802 function = "gpio";
803 bias-pull-up;
804 };
805
806 bios_flash_wp_od: bios-flash-wp-od-state {
807 pins = "gpio16";
808 function = "gpio";
809 /* Has external pull */
810 bias-disable;
811 };
812
813 en_fp_rails: en-fp-rails-state {
814 pins = "gpio77";
815 function = "gpio";
816 bias-disable;
817 drive-strength = <2>;
818 output-high;
819 };
820
821 en_pp3300_codec: en-pp3300-codec-state {
822 pins = "gpio105";
823 function = "gpio";
824 bias-disable;
825 drive-strength = <2>;
826 };
827
828 en_pp3300_dx_edp: en-pp3300-dx-edp-state {
829 pins = "gpio80";
830 function = "gpio";
831 bias-disable;
832 drive-strength = <2>;
833 };
834
835 fp_rst_l: fp-rst-l-state {
836 pins = "gpio78";
837 function = "gpio";
838 bias-disable;
839 drive-strength = <2>;
840 };
841
842 fp_to_ap_irq_l: fp-to-ap-irq-l-state {
843 pins = "gpio61";
844 function = "gpio";
845 /* Has external pullup */
846 bias-disable;
847 };
848
849 fpmcu_boot0: fpmcu-boot0-state {
850 pins = "gpio68";
851 function = "gpio";
852 bias-disable;
853 };
854
855 gsc_ap_int_odl: gsc-ap-int-odl-state {
856 pins = "gpio104";
857 function = "gpio";
858 bias-pull-up;
859 };
860
861 hp_irq: hp-irq-state {
862 pins = "gpio101";
863 function = "gpio";
864 bias-pull-up;
865 };
866
867 hub_en: hub-en-state {
868 pins = "gpio157";
869 function = "gpio";
870 bias-disable;
871 drive-strength = <2>;
872 };
873
874 pe_wake_odl: pe-wake-odl-state {
875 pins = "gpio3";
876 function = "gpio";
877 /* Has external pull */
878 bias-disable;
879 drive-strength = <2>;
880 };
881
882 /* For ap_spi_fp */
883 qup_spi9_cs_gpio_init_high: qup-spi9-cs-gpio-init-high-state {
884 pins = "gpio39";
885 function = "gpio";
886 output-high;
887 };
888
889 /* For ap_ec_spi */
890 qup_spi10_cs_gpio_init_high: qup-spi10-cs-gpio-init-high-state {
891 pins = "gpio43";
892 function = "gpio";
893 output-high;
894 };
895
896 sar0_irq_odl: sar0-irq-odl-state {
897 pins = "gpio141";
898 function = "gpio";
899 bias-pull-up;
900 };
901
902 sar1_irq_odl: sar1-irq-odl-state {
903 pins = "gpio140";
904 function = "gpio";
905 bias-pull-up;
906 };
907
908 sd_cd_odl: sd-cd-odl-state {
909 pins = "gpio91";
910 function = "gpio";
911 bias-pull-up;
912 };
913
914 ssd_en: ssd-en-state {
915 pins = "gpio51";
916 function = "gpio";
917 bias-disable;
918 drive-strength = <2>;
919 };
920
921 ssd_rst_l: ssd-rst-l-state {
922 pins = "gpio2";
923 function = "gpio";
924 bias-disable;
925 drive-strength = <2>;
926 output-low;
927 };
928
929 tp_int_odl: tp-int-odl-state {
930 pins = "gpio7";
931 function = "gpio";
932 /* Has external pullup */
933 bias-disable;
934 };
935
936 wf_cam_en: wf-cam-en-state {
937 pins = "gpio119";
938 function = "gpio";
939 /* Has external pulldown */
940 bias-disable;
941 drive-strength = <2>;
942 };
943 };