| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Google Lazor board device tree source |
| 4 |
* |
| 5 |
* Copyright 2020 Google LLC. |
| 6 |
*/ |
| 7 |
|
| 8 |
#include "sc7180-trogdor-clamshell.dtsi" |
| 9 |
|
| 10 |
&ap_sar_sensor { |
| 11 |
semtech,cs0-ground; |
| 12 |
semtech,combined-sensors = <3>; |
| 13 |
semtech,resolution = "fine"; |
| 14 |
semtech,startup-sensor = <0>; |
| 15 |
semtech,proxraw-strength = <8>; |
| 16 |
semtech,avg-pos-strength = <64>; |
| 17 |
}; |
| 18 |
|
| 19 |
&ap_tp_i2c { |
| 20 |
status = "okay"; |
| 21 |
}; |
| 22 |
|
| 23 |
/* |
| 24 |
* Lazor is stuffed with a 47k NTC as charger thermistor which currently is |
| 25 |
* not supported by the PM6150 ADC driver. Disable the charger thermal zone |
| 26 |
* to avoid using bogus temperature values. |
| 27 |
*/ |
| 28 |
&charger_thermal { |
| 29 |
status = "disabled"; |
| 30 |
}; |
| 31 |
|
| 32 |
ap_ts_pen_1v8: &i2c4 { |
| 33 |
status = "okay"; |
| 34 |
clock-frequency = <400000>; |
| 35 |
|
| 36 |
ap_ts: touchscreen@10 { |
| 37 |
compatible = "hid-over-i2c"; |
| 38 |
reg = <0x10>; |
| 39 |
pinctrl-names = "default"; |
| 40 |
pinctrl-0 = <&ts_int_l>, <&ts_reset_l>; |
| 41 |
|
| 42 |
interrupt-parent = <&tlmm>; |
| 43 |
interrupts = <9 IRQ_TYPE_LEVEL_LOW>; |
| 44 |
|
| 45 |
panel = <&panel>; |
| 46 |
post-power-on-delay-ms = <20>; |
| 47 |
hid-descr-addr = <0x0001>; |
| 48 |
|
| 49 |
vdd-supply = <&pp3300_ts>; |
| 50 |
}; |
| 51 |
}; |
| 52 |
|
| 53 |
&panel { |
| 54 |
compatible = "boe,nv133fhm-n62"; |
| 55 |
}; |
| 56 |
|
| 57 |
&pm6150_adc { |
| 58 |
/delete-node/ channel@4f; |
| 59 |
}; |
| 60 |
|
| 61 |
&pm6150_adc_tm { |
| 62 |
status = "disabled"; |
| 63 |
|
| 64 |
/delete-node/ charger-thermistor@0; |
| 65 |
}; |
| 66 |
|
| 67 |
&trackpad { |
| 68 |
interrupts = <58 IRQ_TYPE_EDGE_FALLING>; |
| 69 |
}; |
| 70 |
|
| 71 |
&wifi { |
| 72 |
qcom,calibration-variant = "GO_LAZOR"; |
| 73 |
}; |
| 74 |
|
| 75 |
/* PINCTRL - modifications to sc7180-trogdor.dtsi */ |
| 76 |
|
| 77 |
&trackpad_int_1v8_odl { |
| 78 |
pins = "gpio58"; |
| 79 |
}; |
| 80 |
|
| 81 |
&ts_reset_l { |
| 82 |
/* This pin is not connected on -rev0, pull up to park. */ |
| 83 |
/delete-property/bias-disable; |
| 84 |
bias-pull-up; |
| 85 |
}; |
| 86 |
|
| 87 |
/* PINCTRL - board-specific pinctrl */ |
| 88 |
|
| 89 |
&tlmm { |
| 90 |
gpio-line-names = "ESIM_MISO", |
| 91 |
"ESIM_MOSI", |
| 92 |
"ESIM_CLK", |
| 93 |
"ESIM_CS_L", |
| 94 |
"", |
| 95 |
"", |
| 96 |
"AP_TP_I2C_SDA", |
| 97 |
"AP_TP_I2C_SCL", |
| 98 |
"TS_RESET_L", |
| 99 |
"TS_INT_L", |
| 100 |
"", |
| 101 |
"EDP_BRIJ_IRQ", |
| 102 |
"AP_EDP_BKLTEN", |
| 103 |
"AP_RAM_ID2", |
| 104 |
"", |
| 105 |
"EDP_BRIJ_I2C_SDA", |
| 106 |
"EDP_BRIJ_I2C_SCL", |
| 107 |
"HUB_RST_L", |
| 108 |
"", |
| 109 |
"AP_RAM_ID1", |
| 110 |
"AP_SKU_ID2", |
| 111 |
"", |
| 112 |
"", |
| 113 |
"AMP_EN", |
| 114 |
"P_SENSOR_INT_L", |
| 115 |
"AP_SAR_SENSOR_SDA", |
| 116 |
"AP_SAR_SENSOR_SCL", |
| 117 |
"", |
| 118 |
"HP_IRQ", |
| 119 |
"AP_RAM_ID0", |
| 120 |
"EN_PP3300_DX_EDP", |
| 121 |
"AP_BRD_ID2", |
| 122 |
"BRIJ_SUSPEND", |
| 123 |
"AP_BRD_ID0", |
| 124 |
"AP_H1_SPI_MISO", |
| 125 |
"AP_H1_SPI_MOSI", |
| 126 |
"AP_H1_SPI_CLK", |
| 127 |
"AP_H1_SPI_CS_L", |
| 128 |
"", |
| 129 |
"", |
| 130 |
"", |
| 131 |
"", |
| 132 |
"H1_AP_INT_ODL", |
| 133 |
"", |
| 134 |
"UART_AP_TX_DBG_RX", |
| 135 |
"UART_DBG_TX_AP_RX", |
| 136 |
"HP_I2C_SDA", |
| 137 |
"HP_I2C_SCL", |
| 138 |
"FORCED_USB_BOOT", |
| 139 |
"", |
| 140 |
"", |
| 141 |
"AMP_DIN", |
| 142 |
"", |
| 143 |
"HP_BCLK", |
| 144 |
"HP_LRCLK", |
| 145 |
"HP_DOUT", |
| 146 |
"HP_DIN", |
| 147 |
"HP_MCLK", |
| 148 |
"TRACKPAD_INT_1V8_ODL", |
| 149 |
"AP_EC_SPI_MISO", |
| 150 |
"AP_EC_SPI_MOSI", |
| 151 |
"AP_EC_SPI_CLK", |
| 152 |
"AP_EC_SPI_CS_L", |
| 153 |
"AP_SPI_CLK", |
| 154 |
"AP_SPI_MOSI", |
| 155 |
"AP_SPI_MISO", |
| 156 |
/* |
| 157 |
* AP_FLASH_WP_L is crossystem ABI. Schematics |
| 158 |
* call it BIOS_FLASH_WP_L. |
| 159 |
*/ |
| 160 |
"AP_FLASH_WP_L", |
| 161 |
"DBG_SPI_HOLD_L", |
| 162 |
"AP_SPI_CS0_L", |
| 163 |
"", |
| 164 |
"", |
| 165 |
"", |
| 166 |
"", |
| 167 |
"", |
| 168 |
"", |
| 169 |
"UIM2_DATA", |
| 170 |
"UIM2_CLK", |
| 171 |
"UIM2_RST", |
| 172 |
"UIM2_PRESENT", |
| 173 |
"UIM1_DATA", |
| 174 |
"UIM1_CLK", |
| 175 |
"UIM1_RST", |
| 176 |
"", |
| 177 |
"EN_PP3300_CODEC", |
| 178 |
"EN_PP3300_HUB", |
| 179 |
"", |
| 180 |
"", |
| 181 |
"", |
| 182 |
"", |
| 183 |
"", |
| 184 |
"AP_SKU_ID1", |
| 185 |
"AP_RST_REQ", |
| 186 |
"", |
| 187 |
"AP_BRD_ID1", |
| 188 |
"AP_EC_INT_L", |
| 189 |
"", |
| 190 |
"", |
| 191 |
"", |
| 192 |
"", |
| 193 |
"", |
| 194 |
"", |
| 195 |
"", |
| 196 |
"", |
| 197 |
"", |
| 198 |
"EDP_BRIJ_EN", |
| 199 |
"AP_SKU_ID0", |
| 200 |
"", |
| 201 |
"", |
| 202 |
"", |
| 203 |
"", |
| 204 |
"", |
| 205 |
"", |
| 206 |
"", |
| 207 |
"", |
| 208 |
"", |
| 209 |
"AP_TS_PEN_I2C_SDA", |
| 210 |
"AP_TS_PEN_I2C_SCL", |
| 211 |
"DP_HOT_PLUG_DET", |
| 212 |
"EC_IN_RW_ODL"; |
| 213 |
}; |