Debian Codegraph @

scripts/dtc/include-prefixes/arm64/qcom/qrb2210-rb1.dts

raw
1 // SPDX-License-Identifier: (GPL-2.0+ OR BSD-3-Clause)
2 /*
3 * Copyright (c) 2023, Linaro Ltd
4 */
5
6 /dts-v1/;
7
8 #include <dt-bindings/gpio/gpio.h>
9 #include <dt-bindings/leds/common.h>
10 #include "agatti.dtsi"
11 #include "pm4125.dtsi"
12
13 / {
14 model = "Qualcomm Technologies, Inc. Robotics RB1";
15 compatible = "qcom,qrb2210-rb1", "qcom,qrb2210", "qcom,qcm2290";
16
17 aliases {
18 serial0 = &uart4;
19 serial1 = &uart3;
20 sdhc1 = &sdhc_1;
21 sdhc2 = &sdhc_2;
22 };
23
24 chosen {
25 stdout-path = "serial0:115200n8";
26 };
27
28 clocks {
29 clk40m: can-clk {
30 compatible = "fixed-clock";
31 clock-frequency = <40000000>;
32 #clock-cells = <0>;
33 };
34 };
35
36 gpio-keys {
37 compatible = "gpio-keys";
38 label = "gpio-keys";
39
40 pinctrl-0 = <&key_volp_n>;
41 pinctrl-names = "default";
42
43 key-volume-up {
44 label = "Volume Up";
45 linux,code = <KEY_VOLUMEUP>;
46 gpios = <&tlmm 96 GPIO_ACTIVE_LOW>;
47 debounce-interval = <15>;
48 linux,can-disable;
49 wakeup-source;
50 };
51 };
52
53 hdmi-connector {
54 compatible = "hdmi-connector";
55 type = "a";
56
57 port {
58 hdmi_con: endpoint {
59 remote-endpoint = <&lt9611_out>;
60 };
61 };
62 };
63
64 i2c2_gpio: i2c {
65 compatible = "i2c-gpio";
66
67 sda-gpios = <&tlmm 6 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
68 scl-gpios = <&tlmm 7 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
69 #address-cells = <1>;
70 #size-cells = <0>;
71
72 status = "disabled";
73 };
74
75 leds {
76 compatible = "gpio-leds";
77
78 led-bt {
79 label = "blue:bt";
80 function = LED_FUNCTION_BLUETOOTH;
81 color = <LED_COLOR_ID_BLUE>;
82 gpios = <&tlmm 45 GPIO_ACTIVE_HIGH>;
83 linux,default-trigger = "bluetooth-power";
84 default-state = "off";
85 };
86
87 led-user0 {
88 label = "green:user0";
89 function = LED_FUNCTION_INDICATOR;
90 color = <LED_COLOR_ID_GREEN>;
91 gpios = <&tlmm 52 GPIO_ACTIVE_HIGH>;
92 linux,default-trigger = "none";
93 default-state = "off";
94 panic-indicator;
95 };
96
97 led-wlan {
98 label = "yellow:wlan";
99 function = LED_FUNCTION_WLAN;
100 color = <LED_COLOR_ID_YELLOW>;
101 gpios = <&tlmm 47 GPIO_ACTIVE_HIGH>;
102 linux,default-trigger = "phy0tx";
103 default-state = "off";
104 };
105 };
106
107 vreg_hdmi_out_1p2: regulator-hdmi-out-1p2 {
108 compatible = "regulator-fixed";
109 regulator-name = "VREG_HDMI_OUT_1P2";
110 regulator-min-microvolt = <1200000>;
111 regulator-max-microvolt = <1200000>;
112 vin-supply = <&vdc_1v2>;
113 regulator-always-on;
114 regulator-boot-on;
115 };
116
117 lt9611_3v3: regulator-lt9611-3v3 {
118 compatible = "regulator-fixed";
119 regulator-name = "LT9611_3V3";
120 regulator-min-microvolt = <3300000>;
121 regulator-max-microvolt = <3300000>;
122 vin-supply = <&vdc_3v3>;
123 regulator-always-on;
124 regulator-boot-on;
125 };
126
127 /* Main barrel jack input */
128 vdc_12v: regulator-vdc-12v {
129 compatible = "regulator-fixed";
130 regulator-name = "DC_12V";
131 regulator-min-microvolt = <12000000>;
132 regulator-max-microvolt = <12000000>;
133 regulator-always-on;
134 regulator-boot-on;
135 };
136
137 /* 1.2V supply stepped down from the barrel jack input */
138 vdc_1v2: regulator-vdc-1v2 {
139 compatible = "regulator-fixed";
140 regulator-name = "VDC_1V2";
141 regulator-min-microvolt = <1200000>;
142 regulator-max-microvolt = <1200000>;
143 vin-supply = <&vdc_12v>;
144 regulator-always-on;
145 regulator-boot-on;
146 };
147
148 /* 3.3V supply stepped down from the barrel jack input */
149 vdc_3v3: regulator-vdc-3v3 {
150 compatible = "regulator-fixed";
151 regulator-name = "VDC_3V3";
152 regulator-min-microvolt = <3300000>;
153 regulator-max-microvolt = <3300000>;
154 vin-supply = <&vdc_12v>;
155 regulator-always-on;
156 regulator-boot-on;
157 };
158
159 /* 5V supply stepped down from the barrel jack input */
160 vdc_5v: regulator-vdc-5v {
161 compatible = "regulator-fixed";
162 regulator-name = "VDC_5V";
163
164 regulator-min-microvolt = <5000000>;
165 regulator-max-microvolt = <5000000>;
166 regulator-always-on;
167 regulator-boot-on;
168 };
169
170 /* "Battery" voltage for the SoM, stepped down from the barrel jack input */
171 vdc_vbat_som: regulator-vdc-vbat {
172 compatible = "regulator-fixed";
173 regulator-name = "VBAT_SOM";
174 regulator-min-microvolt = <4200000>;
175 regulator-max-microvolt = <4200000>;
176 regulator-always-on;
177 regulator-boot-on;
178 };
179
180 /* PM2250 charger out, supplied by VBAT */
181 vph_pwr: regulator-vph-pwr {
182 compatible = "regulator-fixed";
183 regulator-name = "vph_pwr";
184 regulator-min-microvolt = <3700000>;
185 regulator-max-microvolt = <3700000>;
186 vin-supply = <&vdc_vbat_som>;
187
188 regulator-always-on;
189 regulator-boot-on;
190 };
191
192 sound {
193 compatible = "qcom,qrb2210-sndcard";
194 pinctrl-0 = <&lpi_i2s2_active>;
195 pinctrl-names = "default";
196 model = "Qualcomm-RB1-WSA8815-Speaker-DMIC0";
197
198 mm1-dai-link {
199 link-name = "MultiMedia1";
200
201 cpu {
202 sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA1>;
203 };
204 };
205
206 mm2-dai-link {
207 link-name = "MultiMedia2";
208
209 cpu {
210 sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA2>;
211 };
212 };
213
214 mm3-dai-link {
215 link-name = "MultiMedia3";
216
217 cpu {
218 sound-dai = <&q6asmdai MSM_FRONTEND_DAI_MULTIMEDIA3>;
219 };
220 };
221
222 hdmi-i2s-dai-link {
223 link-name = "HDMI/I2S Playback";
224
225 codec {
226 sound-dai = <&lt9611_codec 0>;
227 };
228
229 cpu {
230 sound-dai = <&q6afedai SECONDARY_MI2S_RX>;
231 };
232
233 platform {
234 sound-dai = <&q6routing>;
235 };
236 };
237 };
238 };
239
240 &cpu_pd0 {
241 /delete-property/ power-domains;
242 };
243
244 &cpu_pd1 {
245 /delete-property/ power-domains;
246 };
247
248 &cpu_pd2 {
249 /delete-property/ power-domains;
250 };
251
252 &cpu_pd3 {
253 /delete-property/ power-domains;
254 };
255
256 /delete-node/ &cluster_pd;
257
258 &gpi_dma0 {
259 status = "okay";
260 };
261
262 &gpu {
263 status = "okay";
264 };
265
266 &gpu_zap_shader {
267 firmware-name = "qcom/qcm2290/a702_zap.mbn";
268 };
269
270 &i2c1 {
271 clock-frequency = <400000>;
272
273 status = "okay";
274
275 pm8008: pmic@8 {
276 compatible = "qcom,pm8008";
277 reg = <0x8>;
278
279 interrupts-extended = <&tlmm 25 IRQ_TYPE_EDGE_RISING>;
280 reset-gpios = <&tlmm 26 GPIO_ACTIVE_LOW>;
281
282 vdd-l1-l2-supply = <&pm4125_s3>;
283 vdd-l3-l4-supply = <&vph_pwr>;
284 vdd-l5-supply = <&vph_pwr>;
285 vdd-l6-supply = <&vph_pwr>;
286 vdd-l7-supply = <&vph_pwr>;
287
288 gpio-controller;
289 #gpio-cells = <2>;
290 gpio-ranges = <&pm8008 0 0 2>;
291
292 interrupt-controller;
293 #interrupt-cells = <2>;
294
295 #thermal-sensor-cells = <0>;
296
297 status = "disabled";
298
299 regulators {
300 vreg_l1p: ldo1 {
301 regulator-name = "vreg_l1p";
302 regulator-min-microvolt = <528000>;
303 regulator-max-microvolt = <1200000>;
304 };
305
306 vreg_l2p: ldo2 {
307 regulator-name = "vreg_l2p";
308 regulator-min-microvolt = <528000>;
309 regulator-max-microvolt = <1200000>;
310 };
311
312 vreg_l3p: ldo3 {
313 regulator-name = "vreg_l3p";
314 regulator-min-microvolt = <1500000>;
315 regulator-max-microvolt = <3400000>;
316 };
317
318 vreg_l4p: ldo4 {
319 regulator-name = "vreg_l4p";
320 regulator-min-microvolt = <1500000>;
321 regulator-max-microvolt = <3404000>;
322 };
323
324 vreg_l5p: ldo5 {
325 regulator-name = "vreg_l5p";
326 regulator-min-microvolt = <1500000>;
327 regulator-max-microvolt = <3400000>;
328 };
329
330 vreg_l6p: ldo6 {
331 regulator-name = "vreg_l6p";
332 regulator-min-microvolt = <1500000>;
333 regulator-max-microvolt = <3400000>;
334 };
335
336 vreg_l7p: ldo7 {
337 regulator-name = "vreg_l7p";
338 regulator-min-microvolt = <1500000>;
339 regulator-max-microvolt = <3400000>;
340 };
341 };
342 };
343 };
344
345 &i2c2_gpio {
346 clock-frequency = <400000>;
347 status = "okay";
348
349 lt9611_codec: hdmi-bridge@2b {
350 compatible = "lontium,lt9611uxc";
351 reg = <0x2b>;
352 interrupts-extended = <&tlmm 46 IRQ_TYPE_EDGE_FALLING>;
353 reset-gpios = <&tlmm 41 GPIO_ACTIVE_HIGH>;
354
355 vdd-supply = <&vreg_hdmi_out_1p2>;
356 vcc-supply = <&lt9611_3v3>;
357
358 pinctrl-0 = <&lt9611_irq_pin &lt9611_rst_pin>;
359 pinctrl-names = "default";
360 #sound-dai-cells = <1>;
361
362 ports {
363 #address-cells = <1>;
364 #size-cells = <0>;
365
366 port@0 {
367 reg = <0>;
368
369 lt9611_a: endpoint {
370 remote-endpoint = <&mdss_dsi0_out>;
371 };
372 };
373
374 port@2 {
375 reg = <2>;
376
377 lt9611_out: endpoint {
378 remote-endpoint = <&hdmi_con>;
379 };
380 };
381 };
382 };
383 };
384
385 &mdss {
386 status = "okay";
387 };
388
389 &mdss_dsi0 {
390 vdda-supply = <&pm4125_l5>;
391 status = "okay";
392 };
393
394 &mdss_dsi0_out {
395 remote-endpoint = <&lt9611_a>;
396 data-lanes = <0 1 2 3>;
397 };
398
399 &mdss_dsi0_phy {
400 status = "okay";
401 };
402
403 &pm4125_resin {
404 linux,code = <KEY_VOLUMEDOWN>;
405 status = "okay";
406 };
407
408 &pm4125_typec {
409 status = "okay";
410
411 connector {
412 compatible = "usb-c-connector";
413
414 power-role = "dual";
415 data-role = "dual";
416 self-powered;
417
418 typec-power-opmode = "default";
419 pd-disable;
420
421 ports {
422 #address-cells = <1>;
423 #size-cells = <0>;
424
425 port@0 {
426 reg = <0>;
427 pm4125_hs_in: endpoint {
428 remote-endpoint = <&usb_dwc3_hs>;
429 };
430 };
431
432 port@1 {
433 reg = <1>;
434 pm4125_ss_in: endpoint {
435 remote-endpoint = <&usb_qmpphy_out>;
436 };
437 };
438 };
439 };
440 };
441
442 &pm4125_vbus {
443 regulator-min-microamp = <500000>;
444 regulator-max-microamp = <500000>;
445 status = "okay";
446 };
447
448 /* SECONDARY I2S uses 1 I2S SD Line for audio on LT9611UXC HDMI Bridge */
449 &q6afedai {
450 dai@18 {
451 reg = <SECONDARY_MI2S_RX>;
452 qcom,sd-lines = <0>;
453 };
454 };
455
456 &qupv3_id_0 {
457 status = "okay";
458 };
459
460 &remoteproc_adsp {
461 firmware-name = "qcom/qcm2290/adsp.mbn";
462 status = "okay";
463 };
464
465 &remoteproc_mpss {
466 firmware-name = "qcom/qcm2290/modem.mbn";
467 status = "okay";
468 };
469
470 &rpm_requests {
471 regulators {
472 compatible = "qcom,rpm-pm2250-regulators";
473 vdd_s3-supply = <&vph_pwr>;
474 vdd_s4-supply = <&vph_pwr>;
475 vdd_l1_l2_l3_l5_l6_l7_l8_l9_l10_l11_l12-supply = <&pm4125_s3>;
476 vdd_l4_l17_l18_l19_l20_l21_l22-supply = <&vph_pwr>;
477 vdd_l13_l14_l15_l16-supply = <&pm4125_s4>;
478
479 /*
480 * S1 - VDD_APC
481 * S2 - VDD_CX
482 */
483
484 pm4125_s3: s3 {
485 /* 0.4V-1.6625V -> 1.3V (Power tree requirements) */
486 regulator-min-microvolt = <1352000>;
487 regulator-max-microvolt = <1352000>;
488 regulator-boot-on;
489 };
490
491 pm4125_s4: s4 {
492 /* 1.2V-2.35V -> 2.05V (Power tree requirements) */
493 regulator-min-microvolt = <2072000>;
494 regulator-max-microvolt = <2072000>;
495 regulator-boot-on;
496 };
497
498 /* L1 - VDD_MX */
499
500 pm4125_l2: l2 {
501 /* LPDDR4X VDD2 */
502 regulator-min-microvolt = <1136000>;
503 regulator-max-microvolt = <1136000>;
504 regulator-always-on;
505 regulator-boot-on;
506 };
507
508 pm4125_l3: l3 {
509 /* LPDDR4X VDDQ */
510 regulator-min-microvolt = <616000>;
511 regulator-max-microvolt = <616000>;
512 regulator-always-on;
513 regulator-boot-on;
514 };
515
516 pm4125_l4: l4 {
517 /* max = 3.05V -> max = 2.7 to disable 3V signaling (SDHCI2) */
518 regulator-min-microvolt = <1800000>;
519 regulator-max-microvolt = <2700000>;
520 regulator-allow-set-load;
521 };
522
523 pm4125_l5: l5 {
524 /* CSI/DSI */
525 regulator-min-microvolt = <1232000>;
526 regulator-max-microvolt = <1232000>;
527 regulator-allow-set-load;
528 regulator-boot-on;
529 };
530
531 pm4125_l6: l6 {
532 /* DRAM PLL */
533 regulator-min-microvolt = <928000>;
534 regulator-max-microvolt = <928000>;
535 regulator-always-on;
536 regulator-boot-on;
537 };
538
539 pm4125_l7: l7 {
540 /* Wi-Fi CX/MX */
541 regulator-min-microvolt = <664000>;
542 regulator-max-microvolt = <664000>;
543 };
544
545 /*
546 * L8 - VDD_LPI_CX
547 * L9 - VDD_LPI_MX
548 */
549
550 pm4125_l10: l10 {
551 /* Wi-Fi RFA */
552 regulator-min-microvolt = <1304000>;
553 regulator-max-microvolt = <1304000>;
554 };
555
556 pm4125_l11: l11 {
557 /* GPS RF1 */
558 regulator-min-microvolt = <1000000>;
559 regulator-max-microvolt = <1000000>;
560 regulator-boot-on;
561 };
562
563 pm4125_l12: l12 {
564 /* USB PHYs */
565 regulator-min-microvolt = <928000>;
566 regulator-max-microvolt = <928000>;
567 regulator-allow-set-load;
568 regulator-boot-on;
569 };
570
571 pm4125_l13: l13 {
572 /* USB/QFPROM/PLLs */
573 regulator-min-microvolt = <1800000>;
574 regulator-max-microvolt = <1800000>;
575 regulator-allow-set-load;
576 regulator-boot-on;
577 };
578
579 pm4125_l14: l14 {
580 /* SDHCI1 VQMMC */
581 regulator-min-microvolt = <1800000>;
582 regulator-max-microvolt = <1800000>;
583 regulator-allow-set-load;
584 /* Broken hardware, never turn it off! */
585 regulator-always-on;
586 };
587
588 pm4125_l15: l15 {
589 /* WCD/DSI/BT VDDIO */
590 regulator-min-microvolt = <1800000>;
591 regulator-max-microvolt = <1800000>;
592 regulator-allow-set-load;
593 regulator-always-on;
594 regulator-boot-on;
595 };
596
597 pm4125_l16: l16 {
598 /* GPS RF2 */
599 regulator-min-microvolt = <1800000>;
600 regulator-max-microvolt = <1800000>;
601 regulator-boot-on;
602 };
603
604 pm4125_l17: l17 {
605 regulator-min-microvolt = <3000000>;
606 regulator-max-microvolt = <3000000>;
607 };
608
609 pm4125_l18: l18 {
610 /* VDD_PXn */
611 regulator-min-microvolt = <1800000>;
612 regulator-max-microvolt = <1800000>;
613 };
614
615 pm4125_l19: l19 {
616 /* VDD_PXn */
617 regulator-min-microvolt = <1800000>;
618 regulator-max-microvolt = <1800000>;
619 };
620
621 pm4125_l20: l20 {
622 /* SDHCI1 VMMC */
623 regulator-min-microvolt = <2400000>;
624 regulator-max-microvolt = <3600000>;
625 regulator-allow-set-load;
626 };
627
628 pm4125_l21: l21 {
629 /* SDHCI2 VMMC */
630 regulator-min-microvolt = <2960000>;
631 regulator-max-microvolt = <3300000>;
632 regulator-allow-set-load;
633 regulator-boot-on;
634 };
635
636 pm4125_l22: l22 {
637 /* Wi-Fi */
638 regulator-min-microvolt = <3312000>;
639 regulator-max-microvolt = <3312000>;
640 };
641 };
642 };
643
644 &sdhc_1 {
645 vmmc-supply = <&pm4125_l20>;
646 vqmmc-supply = <&pm4125_l14>;
647 pinctrl-0 = <&sdc1_state_on>;
648 pinctrl-1 = <&sdc1_state_off>;
649 pinctrl-names = "default", "sleep";
650 non-removable;
651 supports-cqe;
652 no-sdio;
653 no-sd;
654 status = "okay";
655 };
656
657 &sdhc_2 {
658 vmmc-supply = <&pm4125_l21>;
659 vqmmc-supply = <&pm4125_l4>;
660 cd-gpios = <&tlmm 88 GPIO_ACTIVE_LOW>;
661 pinctrl-0 = <&sdc2_state_on &sd_det_in_on>;
662 pinctrl-1 = <&sdc2_state_off &sd_det_in_off>;
663 pinctrl-names = "default", "sleep";
664 no-sdio;
665 no-mmc;
666 status = "okay";
667 };
668
669 &spi5 {
670 status = "okay";
671
672 can@0 {
673 compatible = "microchip,mcp2518fd";
674 reg = <0>;
675 interrupts-extended = <&tlmm 39 IRQ_TYPE_LEVEL_LOW>;
676 clocks = <&clk40m>;
677 spi-max-frequency = <10000000>;
678 vdd-supply = <&vdc_5v>;
679 xceiver-supply = <&vdc_5v>;
680 };
681 };
682
683 &tlmm {
684 uart3_default: uart3-default-state {
685 cts-pins {
686 pins = "gpio8";
687 function = "qup3";
688 drive-strength = <2>;
689 bias-bus-hold;
690 };
691
692 rts-pins {
693 pins = "gpio9";
694 function = "qup3";
695 drive-strength = <2>;
696 bias-disable;
697 };
698
699 tx-pins {
700 pins = "gpio10";
701 function = "qup3";
702 drive-strength = <2>;
703 bias-disable;
704 };
705
706 rx-pins {
707 pins = "gpio11";
708 function = "qup3";
709 drive-strength = <2>;
710 bias-pull-up;
711 };
712 };
713
714 uart3_sleep: uart3-sleep-state {
715 cts-pins {
716 pins = "gpio8";
717 function = "gpio";
718 drive-strength = <2>;
719 bias-bus-hold;
720 };
721
722 rts-pins {
723 pins = "gpio9";
724 function = "gpio";
725 drive-strength = <2>;
726 bias-pull-down;
727 };
728
729 tx-pins {
730 pins = "gpio10";
731 function = "gpio";
732 drive-strength = <2>;
733 bias-pull-up;
734 };
735
736 rx-pins {
737 pins = "gpio11";
738 function = "gpio";
739 drive-strength = <2>;
740 bias-pull-up;
741 };
742 };
743
744 lt9611_rst_pin: lt9611-rst-state {
745 pins = "gpio41";
746 function = "gpio";
747 input-disable;
748 output-high;
749 };
750
751 lt9611_irq_pin: lt9611-irq-state {
752 pins = "gpio46";
753 function = "gpio";
754 bias-disable;
755 };
756
757 sd_det_in_on: sd-det-in-on-state {
758 pins = "gpio88";
759 function = "gpio";
760 drive-strength = <2>;
761 bias-pull-up;
762 };
763
764 sd_det_in_off: sd-det-in-off-state {
765 pins = "gpio88";
766 function = "gpio";
767 drive-strength = <2>;
768 bias-disable;
769 };
770
771 key_volp_n: key-volp-n-state {
772 pins = "gpio96";
773 function = "gpio";
774 bias-pull-up;
775 output-disable;
776 };
777 };
778
779 &uart3 {
780 /delete-property/ interrupts;
781 interrupts-extended = <&intc GIC_SPI 330 IRQ_TYPE_LEVEL_HIGH>,
782 <&tlmm 11 IRQ_TYPE_EDGE_FALLING>;
783 pinctrl-0 = <&uart3_default>;
784 pinctrl-1 = <&uart3_sleep>;
785 pinctrl-names = "default", "sleep";
786
787 status = "okay";
788
789 bluetooth {
790 compatible = "qcom,wcn3950-bt";
791
792 vddio-supply = <&pm4125_l15>;
793 vddxo-supply = <&pm4125_l13>;
794 vddrf-supply = <&pm4125_l10>;
795 vddch0-supply = <&pm4125_l22>;
796 enable-gpios = <&tlmm 87 GPIO_ACTIVE_HIGH>;
797 max-speed = <3200000>;
798 };
799 };
800
801 /* UART connected to the Micro-USB port via a FTDI chip */
802 &uart4 {
803 compatible = "qcom,geni-debug-uart";
804 status = "okay";
805 };
806
807 &usb {
808 status = "okay";
809 };
810
811 &usb_dwc3_hs {
812 remote-endpoint = <&pm4125_hs_in>;
813 };
814
815 &usb_hsphy {
816 vdd-supply = <&pm4125_l12>;
817 vdda-pll-supply = <&pm4125_l13>;
818 vdda-phy-dpdm-supply = <&pm4125_l21>;
819 status = "okay";
820 };
821
822 &usb_qmpphy {
823 vdda-phy-supply = <&pm4125_l12>;
824 vdda-pll-supply = <&pm4125_l13>;
825 status = "okay";
826 };
827
828 &usb_qmpphy_out {
829 remote-endpoint = <&pm4125_ss_in>;
830 };
831
832 &venus {
833 status = "okay";
834 };
835
836 &wifi {
837 vdd-0.8-cx-mx-supply = <&pm4125_l7>;
838 vdd-1.8-xo-supply = <&pm4125_l13>;
839 vdd-1.3-rfa-supply = <&pm4125_l10>;
840 vdd-3.3-ch0-supply = <&pm4125_l22>;
841 qcom,calibration-variant = "Thundercomm_RB1";
842 firmware-name = "qcm2290";
843 status = "okay";
844 };
845
846 &xo_board {
847 clock-frequency = <38400000>;
848 };