Debian Codegraph @

scripts/dtc/include-prefixes/arm64/qcom/qcm6490-shift-otter.dts

raw
1 // SPDX-License-Identifier: BSD-3-Clause
2 /*
3 * Copyright (c) 2023, Luca Weiss <[email protected]>
4 * Copyright (c) 2024, Casey Connolly <[email protected]>
5 */
6
7 /dts-v1/;
8
9 #define PM7250B_SID 8
10 #define PM7250B_SID1 9
11
12 #include <dt-bindings/iio/qcom,spmi-adc7-pm7325.h>
13 #include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
14 #include <dt-bindings/leds/common.h>
15 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
16 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
17 #include "kodiak.dtsi"
18 #include "pm7250b.dtsi"
19 #include "pm7325.dtsi"
20 #include "pm8350c.dtsi" /* PM7350C */
21 #include "pmk8350.dtsi" /* PMK7325 */
22
23 /delete-node/ &rmtfs_mem;
24
25 / {
26 model = "SHIFT SHIFTphone 8";
27 compatible = "shift,otter", "qcom,qcm6490";
28 chassis-type = "handset";
29
30 aliases {
31 serial0 = &uart5;
32 serial1 = &uart7;
33 };
34
35 chosen {
36 #address-cells = <2>;
37 #size-cells = <2>;
38 ranges;
39
40 stdout-path = "serial0:115200n8";
41
42 framebuffer0: framebuffer@a000000 {
43 compatible = "simple-framebuffer";
44 reg = <0x0 0xe1000000 0x0 (2400 * 1080 * 4)>;
45 width = <1080>;
46 height = <2400>;
47 stride = <(1080 * 4)>;
48 format = "a8r8g8b8";
49 clocks = <&gcc GCC_DISP_HF_AXI_CLK>;
50 };
51 };
52
53 gpio-keys {
54 compatible = "gpio-keys";
55
56 pinctrl-0 = <&volume_down_default>;
57 pinctrl-names = "default";
58
59 key-volume-up {
60 label = "Volume up";
61 gpios = <&pm7325_gpios 6 GPIO_ACTIVE_LOW>;
62 linux,code = <KEY_VOLUMEUP>;
63 debounce-interval = <15>;
64 };
65 };
66
67 pmic-glink {
68 compatible = "qcom,qcm6490-pmic-glink", "qcom,pmic-glink";
69
70 #address-cells = <1>;
71 #size-cells = <0>;
72
73 connector@0 {
74 compatible = "usb-c-connector";
75 reg = <0>;
76 power-role = "dual";
77 data-role = "dual";
78
79 ports {
80 #address-cells = <1>;
81 #size-cells = <0>;
82
83 port@0 {
84 reg = <0>;
85
86 pmic_glink_hs_in: endpoint {
87 remote-endpoint = <&usb_1_dwc3_hs>;
88 };
89 };
90
91 port@1 {
92 reg = <1>;
93
94 pmic_glink_ss_in: endpoint {
95 remote-endpoint = <&usb_dp_qmpphy_out>;
96 };
97 };
98
99 port@2 {
100 reg = <2>;
101
102 pmic_glink_sbu: endpoint {
103 remote-endpoint = <&fsa4480_sbu_mux>;
104 };
105 };
106 };
107 };
108 };
109
110 reserved-memory {
111 cont_splash_mem: cont-splash@e1000000 {
112 reg = <0x0 0xe1000000 0x0 0x2300000>;
113 no-map;
114 };
115
116 cdsp_mem: cdsp@88f00000 {
117 reg = <0x0 0x88f00000 0x0 0x1e00000>;
118 no-map;
119 };
120
121 removed_mem: removed@c0000000 {
122 reg = <0x0 0xc0000000 0x0 0x5100000>;
123 no-map;
124 };
125
126 rmtfs_mem: rmtfs@f8500000 {
127 compatible = "qcom,rmtfs-mem";
128 reg = <0x0 0xf8500000 0x0 0x600000>;
129 no-map;
130
131 qcom,client-id = <1>;
132 qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>, <QCOM_SCM_VMID_NAV>;
133 };
134 };
135
136 thermal-zones {
137 camera-thermal {
138 thermal-sensors = <&pmk8350_adc_tm 2>;
139
140 trips {
141 active-config0 {
142 temperature = <125000>;
143 hysteresis = <1000>;
144 type = "passive";
145 };
146 };
147 };
148
149 chg-skin-thermal {
150 thermal-sensors = <&pm7250b_adc_tm 0>;
151
152 trips {
153 active-config0 {
154 temperature = <125000>;
155 hysteresis = <1000>;
156 type = "passive";
157 };
158 };
159 };
160
161 conn-thermal {
162 thermal-sensors = <&pm7250b_adc_tm 1>;
163
164 trips {
165 active-config0 {
166 temperature = <125000>;
167 hysteresis = <1000>;
168 type = "passive";
169 };
170 };
171 };
172
173 quiet-thermal {
174 thermal-sensors = <&pmk8350_adc_tm 1>;
175
176 trips {
177 active-config0 {
178 temperature = <125000>;
179 hysteresis = <1000>;
180 type = "passive";
181 };
182 };
183 };
184
185 rear-cam-thermal {
186 thermal-sensors = <&pmk8350_adc_tm 4>;
187
188 trips {
189 active-config0 {
190 temperature = <125000>;
191 hysteresis = <1000>;
192 type = "passive";
193 };
194 };
195 };
196
197 sdm-skin-thermal {
198 thermal-sensors = <&pmk8350_adc_tm 3>;
199
200 trips {
201 active-config0 {
202 temperature = <125000>;
203 hysteresis = <1000>;
204 type = "passive";
205 };
206 };
207 };
208
209 xo-thermal {
210 thermal-sensors = <&pmk8350_adc_tm 0>;
211
212 trips {
213 active-config0 {
214 temperature = <125000>;
215 hysteresis = <1000>;
216 type = "passive";
217 };
218 };
219 };
220 };
221 };
222
223 &apps_rsc {
224 regulators-0 {
225 compatible = "qcom,pm7325-rpmh-regulators";
226 qcom,pmic-id = "b";
227
228 vreg_s1b: smps1 {
229 regulator-name = "vreg_s1b";
230 regulator-min-microvolt = <1840000>;
231 regulator-max-microvolt = <2040000>;
232 };
233
234 vreg_s7b: smps7 {
235 regulator-name = "vreg_s7b";
236 regulator-min-microvolt = <535000>;
237 regulator-max-microvolt = <1120000>;
238 };
239
240 vreg_s8b: smps8 {
241 regulator-name = "vreg_s8b";
242 regulator-min-microvolt = <1200000>;
243 regulator-max-microvolt = <1500000>;
244 regulator-initial-mode = <RPMH_REGULATOR_MODE_RET>;
245 };
246
247 vreg_l1b: ldo1 {
248 regulator-name = "vreg_l1b";
249 regulator-min-microvolt = <825000>;
250 regulator-max-microvolt = <925000>;
251 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
252 };
253
254 vreg_l2b: ldo2 {
255 regulator-name = "vreg_l2b";
256 regulator-min-microvolt = <2700000>;
257 regulator-max-microvolt = <3544000>;
258 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
259 };
260
261 vreg_l3b: ldo3 {
262 regulator-name = "vreg_l3b";
263 regulator-min-microvolt = <312000>;
264 regulator-max-microvolt = <910000>;
265 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
266 };
267
268 vreg_l6b: ldo6 {
269 regulator-name = "vreg_l6b";
270 regulator-min-microvolt = <1140000>;
271 regulator-max-microvolt = <1260000>;
272 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
273 };
274
275 vreg_l7b: ldo7 {
276 regulator-name = "vreg_l7b";
277 /* Constrained for UFS VCC, at least until UFS driver scales voltage */
278 regulator-min-microvolt = <2952000>;
279 regulator-max-microvolt = <2952000>;
280 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
281 };
282
283 vreg_l8b: ldo8 {
284 regulator-name = "vreg_l8b";
285 regulator-min-microvolt = <870000>;
286 regulator-max-microvolt = <970000>;
287 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
288 };
289
290 vreg_l9b: ldo9 {
291 regulator-name = "vreg_l9b";
292 regulator-min-microvolt = <1200000>;
293 regulator-max-microvolt = <1304000>;
294 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
295 };
296
297 vreg_l11b: ldo11 {
298 regulator-name = "vreg_l11b";
299 regulator-min-microvolt = <1504000>;
300 regulator-max-microvolt = <2000000>;
301 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
302 };
303
304 vreg_l12b: ldo12 {
305 regulator-name = "vreg_l12b";
306 regulator-min-microvolt = <751000>;
307 regulator-max-microvolt = <824000>;
308 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
309 };
310
311 vreg_l13b: ldo13 {
312 regulator-name = "vreg_l13b";
313 regulator-min-microvolt = <530000>;
314 regulator-max-microvolt = <824000>;
315 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
316 };
317
318 vreg_l14b: ldo14 {
319 regulator-name = "vreg_l14b";
320 regulator-min-microvolt = <1080000>;
321 regulator-max-microvolt = <1304000>;
322 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
323 };
324
325 vreg_l15b: ldo15 {
326 regulator-name = "vreg_l15b";
327 regulator-min-microvolt = <765000>;
328 regulator-max-microvolt = <1020000>;
329 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
330 };
331
332 vreg_l16b: ldo16 {
333 regulator-name = "vreg_l16b";
334 regulator-min-microvolt = <1100000>;
335 regulator-max-microvolt = <1300000>;
336 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
337 };
338
339 vreg_l17b: ldo17 {
340 regulator-name = "vreg_l17b";
341 regulator-min-microvolt = <1700000>;
342 regulator-max-microvolt = <1900000>;
343 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
344 };
345
346 vreg_l18b: ldo18 {
347 regulator-name = "vreg_l18b";
348 regulator-min-microvolt = <1800000>;
349 regulator-max-microvolt = <2000000>;
350 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
351 };
352
353 vreg_l19b: ldo19 {
354 regulator-name = "vreg_l19b";
355 regulator-min-microvolt = <1800000>;
356 regulator-max-microvolt = <2000000>;
357 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
358 };
359 };
360
361 regulators-1 {
362 compatible = "qcom,pm8350c-rpmh-regulators";
363 qcom,pmic-id = "c";
364
365 vreg_s1c: smps1 {
366 regulator-name = "vreg_s1c";
367 regulator-min-microvolt = <2190000>;
368 regulator-max-microvolt = <2210000>;
369 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
370 };
371
372 vreg_s9c: smps9 {
373 regulator-name = "vreg_s9c";
374 regulator-min-microvolt = <1010000>;
375 regulator-max-microvolt = <1170000>;
376 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
377 };
378
379 vreg_l1c: ldo1 {
380 regulator-name = "vreg_l1c";
381 regulator-min-microvolt = <1800000>;
382 regulator-max-microvolt = <1980000>;
383 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
384 };
385
386 vreg_l2c: ldo2 {
387 regulator-name = "vreg_l2c";
388 regulator-min-microvolt = <1800000>;
389 regulator-max-microvolt = <1950000>;
390 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
391 };
392
393 vreg_l3c: ldo3 {
394 regulator-name = "vreg_l3c";
395 regulator-min-microvolt = <3000000>;
396 regulator-max-microvolt = <3400000>;
397 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
398 };
399
400 vreg_l4c: ldo4 {
401 regulator-name = "vreg_l4c";
402 regulator-min-microvolt = <1620000>;
403 regulator-max-microvolt = <3300000>;
404 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
405 };
406
407 vreg_l5c: ldo5 {
408 regulator-name = "vreg_l5c";
409 regulator-min-microvolt = <1620000>;
410 regulator-max-microvolt = <3300000>;
411 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
412 };
413
414 vreg_l6c: ldo6 {
415 regulator-name = "vreg_l6c";
416 regulator-min-microvolt = <1650000>;
417 regulator-max-microvolt = <3544000>;
418 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
419 };
420
421 vreg_l7c: ldo7 {
422 regulator-name = "vreg_l7c";
423 regulator-min-microvolt = <3000000>;
424 regulator-max-microvolt = <3544000>;
425 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
426 };
427
428 vreg_l8c: ldo8 {
429 regulator-name = "vreg_l8c";
430 regulator-min-microvolt = <1620000>;
431 regulator-max-microvolt = <2000000>;
432 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
433 };
434
435 vreg_l9c: ldo9 {
436 regulator-name = "vreg_l9c";
437 regulator-min-microvolt = <2700000>;
438 regulator-max-microvolt = <3544000>;
439 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
440 };
441
442 vreg_l10c: ldo10 {
443 regulator-name = "vreg_l10c";
444 regulator-min-microvolt = <720000>;
445 regulator-max-microvolt = <1050000>;
446 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
447 };
448
449 vreg_l11c: ldo11 {
450 regulator-name = "vreg_l11c";
451 regulator-min-microvolt = <2800000>;
452 regulator-max-microvolt = <3544000>;
453 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
454 };
455
456 vreg_l12c: ldo12 {
457 regulator-name = "vreg_l12c";
458 regulator-min-microvolt = <1650000>;
459 regulator-max-microvolt = <2000000>;
460 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
461 };
462
463 vreg_l13c: ldo13 {
464 regulator-name = "vreg_l13c";
465 regulator-min-microvolt = <2700000>;
466 regulator-max-microvolt = <3544000>;
467 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
468 };
469
470 vreg_bob: bob {
471 regulator-name = "vreg_bob";
472 regulator-min-microvolt = <3008000>;
473 regulator-max-microvolt = <3960000>;
474 regulator-initial-mode = <RPMH_REGULATOR_MODE_AUTO>;
475 };
476 };
477 };
478
479 &gcc {
480 protected-clocks = <GCC_CFG_NOC_LPASS_CLK>,
481 <GCC_EDP_CLKREF_EN>,
482 <GCC_MSS_CFG_AHB_CLK>,
483 <GCC_MSS_GPLL0_MAIN_DIV_CLK_SRC>,
484 <GCC_MSS_OFFLINE_AXI_CLK>,
485 <GCC_MSS_Q6SS_BOOT_CLK_SRC>,
486 <GCC_MSS_Q6_MEMNOC_AXI_CLK>,
487 <GCC_MSS_SNOC_AXI_CLK>,
488 <GCC_QSPI_CNOC_PERIPH_AHB_CLK>,
489 <GCC_QSPI_CORE_CLK>,
490 <GCC_QSPI_CORE_CLK_SRC>,
491 <GCC_SEC_CTRL_CLK_SRC>,
492 <GCC_WPSS_AHB_BDG_MST_CLK>,
493 <GCC_WPSS_AHB_CLK>,
494 <GCC_WPSS_RSCP_CLK>;
495 };
496
497 &gpi_dma0 {
498 status = "okay";
499 };
500
501 &gpi_dma1 {
502 status = "okay";
503 };
504
505 &gpu {
506 status = "okay";
507 };
508
509 &gpu_zap_shader {
510 firmware-name = "qcom/qcm6490/SHIFT/otter/a660_zap.mbn";
511 };
512
513 &i2c1 {
514 status = "okay";
515
516 /* PM8008 PMIC @ 8 and 9 */
517 /* rtc6226 FM receiver @ 64 */
518
519 typec-mux@42 {
520 compatible = "fcs,fsa4480";
521 reg = <0x42>;
522
523 vcc-supply = <&vreg_bob>;
524
525 mode-switch;
526 orientation-switch;
527
528 port {
529 fsa4480_sbu_mux: endpoint {
530 remote-endpoint = <&pmic_glink_sbu>;
531 };
532 };
533 };
534 };
535
536 &i2c4 {
537 status = "okay";
538
539 /* tas2563 audio codec @ 4d */
540 };
541
542 &i2c9 {
543 status = "okay";
544
545 /* TMS(?) NFC @ 28 */
546 /* Ti drv2624 haptics @ 5a */
547 };
548
549 &i2c13 {
550 status = "okay";
551
552 /* focaltech FT3658U @ 38 */
553 };
554
555 &ipa {
556 qcom,gsi-loader = "self";
557 memory-region = <&ipa_fw_mem>;
558 firmware-name = "qcom/qcm6490/SHIFT/otter/ipa_fws.mbn";
559 status = "okay";
560 };
561
562 &lpass_audiocc {
563 compatible = "qcom,qcm6490-lpassaudiocc";
564 /delete-property/ power-domains;
565 };
566
567 &pm7250b_adc {
568 channel@4d {
569 reg = <ADC5_AMUX_THM1_100K_PU>;
570 qcom,ratiometric;
571 qcom,hw-settle-time = <200>;
572 qcom,pre-scaling = <1 1>;
573 label = "charger_skin_therm";
574 };
575
576 channel@4f {
577 reg = <ADC5_AMUX_THM3_100K_PU>;
578 qcom,ratiometric;
579 qcom,hw-settle-time = <200>;
580 qcom,pre-scaling = <1 1>;
581 label = "conn_therm";
582 };
583 };
584
585 &pm7250b_adc_tm {
586 status = "okay";
587
588 charger-skin-therm@0 {
589 reg = <0>;
590 io-channels = <&pm7250b_adc ADC5_AMUX_THM1_100K_PU>;
591 qcom,ratiometric;
592 qcom,hw-settle-time-us = <200>;
593 };
594
595 conn-therm@1 {
596 reg = <1>;
597 io-channels = <&pm7250b_adc ADC5_AMUX_THM3_100K_PU>;
598 qcom,ratiometric;
599 qcom,hw-settle-time-us = <200>;
600 };
601 };
602
603 &pm7325_gpios {
604 volume_down_default: volume-down-default-state {
605 pins = "gpio6";
606 function = PMIC_GPIO_FUNC_NORMAL;
607 power-source = <1>;
608 bias-pull-up;
609 input-enable;
610 };
611 };
612
613 &pm8350c_flash {
614 status = "okay";
615
616 led-0 {
617 function = LED_FUNCTION_FLASH;
618 color = <LED_COLOR_ID_WHITE>;
619 led-sources = <1>, <2>;
620 led-max-microamp = <500000>;
621 flash-max-microamp = <1500000>;
622 flash-max-timeout-us = <1280000>;
623 };
624 };
625
626 &pm8350c_pwm {
627 status = "okay";
628
629 multi-led {
630 color = <LED_COLOR_ID_RGB>;
631 function = LED_FUNCTION_STATUS;
632
633 #address-cells = <1>;
634 #size-cells = <0>;
635
636 led@1 {
637 reg = <1>;
638 color = <LED_COLOR_ID_RED>;
639 };
640
641 led@2 {
642 reg = <2>;
643 color = <LED_COLOR_ID_GREEN>;
644 };
645
646 led@3 {
647 reg = <3>;
648 color = <LED_COLOR_ID_BLUE>;
649 };
650 };
651 };
652
653 &pmk8350_adc_tm {
654 status = "okay";
655
656 xo-therm@0 {
657 reg = <0>;
658 io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>;
659 qcom,ratiometric;
660 qcom,hw-settle-time-us = <200>;
661 };
662
663 quiet-therm@1 {
664 reg = <1>;
665 io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM1_100K_PU>;
666 qcom,ratiometric;
667 qcom,hw-settle-time-us = <200>;
668 };
669
670 cam-flash-therm@2 {
671 reg = <2>;
672 io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM2_100K_PU>;
673 qcom,ratiometric;
674 qcom,hw-settle-time-us = <200>;
675 };
676
677 sdm-skin-therm@3 {
678 reg = <3>;
679 io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM3_100K_PU>;
680 qcom,ratiometric;
681 qcom,hw-settle-time-us = <200>;
682 };
683
684 wide-rfc-therm@4 {
685 reg = <4>;
686 io-channels = <&pmk8350_vadc PM7325_ADC7_AMUX_THM4_100K_PU>;
687 qcom,ratiometric;
688 qcom,hw-settle-time-us = <200>;
689 };
690 };
691
692 &pmk8350_rtc {
693 status = "okay";
694 };
695
696 &pmk8350_vadc {
697 status = "okay";
698
699 channel@44 {
700 reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>;
701 qcom,ratiometric;
702 qcom,hw-settle-time = <200>;
703 qcom,pre-scaling = <1 1>;
704 label = "pmk8350_xo_therm";
705 };
706
707 channel@144 {
708 reg = <PM7325_ADC7_AMUX_THM1_100K_PU>;
709 qcom,ratiometric;
710 qcom,hw-settle-time = <200>;
711 qcom,pre-scaling = <1 1>;
712 label = "pm7325_quiet_therm";
713 };
714
715 channel@145 {
716 reg = <PM7325_ADC7_AMUX_THM2_100K_PU>;
717 qcom,ratiometric;
718 qcom,hw-settle-time = <200>;
719 qcom,pre-scaling = <1 1>;
720 label = "pm7325_cam_flash_therm";
721 };
722
723 channel@146 {
724 reg = <PM7325_ADC7_AMUX_THM3_100K_PU>;
725 qcom,ratiometric;
726 qcom,hw-settle-time = <200>;
727 qcom,pre-scaling = <1 1>;
728 label = "pm7325_sdm_skin_therm";
729 };
730
731 channel@147 {
732 reg = <PM7325_ADC7_AMUX_THM4_100K_PU>;
733 qcom,ratiometric;
734 qcom,hw-settle-time = <200>;
735 qcom,pre-scaling = <1 1>;
736 label = "pm7325_wide_rfc_therm";
737 };
738 };
739
740 &pon_pwrkey {
741 status = "okay";
742 };
743
744 &pon_resin {
745 linux,code = <KEY_VOLUMEDOWN>;
746 status = "okay";
747 };
748
749 &qup_spi13_cs {
750 drive-strength = <6>;
751 bias-disable;
752 };
753
754 &qup_spi13_data_clk {
755 drive-strength = <6>;
756 bias-disable;
757 };
758
759 &qup_uart5_rx {
760 drive-strength = <2>;
761 bias-disable;
762 };
763
764 &qup_uart5_tx {
765 drive-strength = <2>;
766 bias-disable;
767 };
768
769 &qupv3_id_0 {
770 status = "okay";
771 };
772
773 &qupv3_id_1 {
774 status = "okay";
775 };
776
777 &remoteproc_adsp {
778 firmware-name = "qcom/qcm6490/SHIFT/otter/adsp.mbn";
779 status = "okay";
780 };
781
782 &remoteproc_cdsp {
783 firmware-name = "qcom/qcm6490/SHIFT/otter/cdsp.mbn";
784 status = "okay";
785 };
786
787 &remoteproc_mpss {
788 firmware-name = "qcom/qcm6490/SHIFT/otter/modem.mbn";
789 status = "okay";
790 };
791
792 &remoteproc_wpss {
793 firmware-name = "qcom/qcm6490/SHIFT/otter/wpss.mbn";
794 status = "okay";
795 };
796
797 &sdc2_clk {
798 drive-strength = <16>;
799 bias-disable;
800 };
801
802 &sdc2_cmd {
803 drive-strength = <10>;
804 bias-pull-up;
805 };
806
807 &sdc2_data {
808 drive-strength = <10>;
809 bias-pull-up;
810 };
811
812 &sdhc_2 {
813 vmmc-supply = <&vreg_l9c>;
814 vqmmc-supply = <&vreg_l6c>;
815
816 pinctrl-0 = <&sdc2_clk>, <&sdc2_cmd>, <&sdc2_data>;
817 pinctrl-1 = <&sdc2_clk_sleep>, <&sdc2_cmd_sleep>, <&sdc2_data_sleep>;
818
819 status = "okay";
820 };
821
822 &tlmm {
823 /*
824 * 48-52: protected by XPU, not sure why.
825 */
826 gpio-reserved-ranges = <48 4>;
827
828 bluetooth_enable_default: bluetooth-enable-default-state {
829 pins = "gpio85";
830 function = "gpio";
831 output-low;
832 bias-disable;
833 };
834
835 qup_uart7_sleep_cts: qup-uart7-sleep-cts-state {
836 pins = "gpio28";
837 function = "gpio";
838 /*
839 * Configure a bias-bus-hold on CTS to lower power
840 * usage when Bluetooth is turned off. Bus hold will
841 * maintain a low power state regardless of whether
842 * the Bluetooth module drives the pin in either
843 * direction or leaves the pin fully unpowered.
844 */
845 bias-bus-hold;
846 };
847
848 qup_uart7_sleep_rts: qup-uart7-sleep-rts-state {
849 pins = "gpio29";
850 function = "gpio";
851 /*
852 * Configure pull-down on RTS. As RTS is active low
853 * signal, pull it low to indicate the BT SoC that it
854 * can wakeup the system anytime from suspend state by
855 * pulling RX low (by sending wakeup bytes).
856 */
857 bias-pull-down;
858 };
859
860 qup_uart7_sleep_tx: qup-uart7-sleep-tx-state {
861 pins = "gpio30";
862 function = "gpio";
863 /*
864 * Configure pull-up on TX when it isn't actively driven
865 * to prevent BT SoC from receiving garbage during sleep.
866 */
867 bias-pull-up;
868 };
869
870 qup_uart7_sleep_rx: qup-uart7-sleep-rx-state {
871 pins = "gpio31";
872 function = "gpio";
873 /*
874 * Configure a pull-up on RX. This is needed to avoid
875 * garbage data when the TX pin of the Bluetooth module
876 * is floating which may cause spurious wakeups.
877 */
878 bias-pull-up;
879 };
880
881 sw_ctrl_default: sw-ctrl-default-state {
882 pins = "gpio86";
883 function = "gpio";
884 bias-pull-down;
885 };
886 };
887
888 &uart5 {
889 compatible = "qcom,geni-debug-uart";
890 status = "okay";
891 };
892
893 &uart7 {
894 /delete-property/interrupts;
895 interrupts-extended = <&intc GIC_SPI 608 IRQ_TYPE_LEVEL_HIGH>,
896 <&tlmm 31 IRQ_TYPE_EDGE_FALLING>;
897
898 pinctrl-1 = <&qup_uart7_sleep_cts>, <&qup_uart7_sleep_rts>, <&qup_uart7_sleep_tx>, <&qup_uart7_sleep_rx>;
899 pinctrl-names = "default", "sleep";
900
901 status = "okay";
902
903 bluetooth: bluetooth {
904 compatible = "qcom,wcn6750-bt";
905
906 pinctrl-0 = <&bluetooth_enable_default>, <&sw_ctrl_default>;
907 pinctrl-names = "default";
908
909 enable-gpios = <&tlmm 85 GPIO_ACTIVE_HIGH>;
910 swctrl-gpios = <&tlmm 86 GPIO_ACTIVE_HIGH>;
911
912 vddio-supply = <&vreg_l19b>;
913 vddaon-supply = <&vreg_s7b>;
914 vddbtcxmx-supply = <&vreg_s7b>;
915 vddrfacmn-supply = <&vreg_s7b>;
916 vddrfa0p8-supply = <&vreg_s7b>;
917 vddrfa1p7-supply = <&vreg_s1b>;
918 vddrfa1p2-supply = <&vreg_s8b>;
919 vddrfa2p2-supply = <&vreg_s1c>;
920 vddasd-supply = <&vreg_l11c>;
921
922 max-speed = <3200000>;
923 };
924 };
925
926 &ufs_mem_hc {
927 reset-gpios = <&tlmm 175 GPIO_ACTIVE_LOW>;
928
929 vcc-supply = <&vreg_l7b>;
930 vcc-max-microamp = <800000>;
931 /*
932 * Technically l9b enables an eLDO (supplied by s1b) which then powers
933 * VCCQ2 of the UFS.
934 */
935 vccq-supply = <&vreg_l9b>;
936 vccq-max-microamp = <900000>;
937
938 status = "okay";
939 };
940
941 &ufs_mem_phy {
942 vdda-phy-supply = <&vreg_l10c>;
943 vdda-pll-supply = <&vreg_l6b>;
944
945 status = "okay";
946 };
947
948 &usb_1 {
949 dr_mode = "otg";
950 usb-role-switch;
951
952 status = "okay";
953 };
954
955 &usb_1_dwc3_hs {
956 remote-endpoint = <&pmic_glink_hs_in>;
957 };
958
959 &usb_1_hsphy {
960 vdda-pll-supply = <&vreg_l10c>;
961 vdda18-supply = <&vreg_l1c>;
962 vdda33-supply = <&vreg_l2b>;
963
964 qcom,hs-crossover-voltage-microvolt = <28000>;
965 qcom,hs-output-impedance-micro-ohms = <2600000>;
966 qcom,hs-rise-fall-time-bp = <5430>;
967 qcom,hs-disconnect-bp = <1743>;
968 qcom,hs-amplitude-bp = <2430>;
969
970 qcom,pre-emphasis-amplitude-bp = <20000>;
971 qcom,pre-emphasis-duration-bp = <20000>;
972
973 qcom,squelch-detector-bp = <(-2090)>;
974
975 status = "okay";
976 };
977
978 &usb_1_qmpphy {
979 vdda-phy-supply = <&vreg_l6b>;
980 vdda-pll-supply = <&vreg_l1b>;
981
982 status = "okay";
983 };
984
985 &usb_dp_qmpphy_out {
986 remote-endpoint = <&pmic_glink_ss_in>;
987 };
988
989 &venus {
990 firmware-name = "qcom/qcm6490/SHIFT/otter/venus.mbn";
991
992 status = "okay";
993 };
994
995 &wifi {
996 qcom,calibration-variant = "SHIFTphone_8";
997
998 status = "okay";
999 };