Debian Codegraph @

scripts/dtc/include-prefixes/arm64/qcom/pm8994.dtsi

raw
1 // SPDX-License-Identifier: GPL-2.0
2 #include <dt-bindings/iio/qcom,spmi-vadc.h>
3 #include <dt-bindings/input/linux-event-codes.h>
4 #include <dt-bindings/interrupt-controller/irq.h>
5 #include <dt-bindings/spmi/spmi.h>
6
7 / {
8 thermal-zones {
9 pm8994-thermal {
10 polling-delay-passive = <250>;
11
12 thermal-sensors = <&pm8994_temp>;
13
14 trips {
15 pm8994_alert0: pm8994-alert0 {
16 temperature = <95000>;
17 hysteresis = <2000>;
18 type = "passive";
19 };
20 pm8994_crit: pm8994-crit {
21 temperature = <125000>;
22 hysteresis = <2000>;
23 type = "critical";
24 };
25 };
26 };
27 };
28 };
29
30 &spmi_bus {
31
32 pmic@0 {
33 compatible = "qcom,pm8994", "qcom,spmi-pmic";
34 reg = <0x0 SPMI_USID>;
35 #address-cells = <1>;
36 #size-cells = <0>;
37
38 rtc@6000 {
39 compatible = "qcom,pm8941-rtc";
40 reg = <0x6000>, <0x6100>;
41 reg-names = "rtc", "alarm";
42 interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
43 };
44
45 pm8994_pon: pon@800 {
46 compatible = "qcom,pm8916-pon";
47 reg = <0x800>;
48 mode-bootloader = <0x2>;
49 mode-recovery = <0x1>;
50
51 pwrkey {
52 compatible = "qcom,pm8941-pwrkey";
53 interrupts = <0x0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
54 debounce = <15625>;
55 bias-pull-up;
56 linux,code = <KEY_POWER>;
57 };
58
59 pm8994_resin: resin {
60 compatible = "qcom,pm8941-resin";
61 interrupts = <0x0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
62 debounce = <15625>;
63 bias-pull-up;
64 status = "disabled";
65 };
66 };
67
68 pm8994_temp: temp-alarm@2400 {
69 compatible = "qcom,spmi-temp-alarm";
70 reg = <0x2400>;
71 interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_RISING>;
72 io-channels = <&pm8994_vadc VADC_DIE_TEMP>;
73 io-channel-names = "thermal";
74 #thermal-sensor-cells = <0>;
75 };
76
77 pm8994_vadc: adc@3100 {
78 compatible = "qcom,spmi-vadc";
79 reg = <0x3100>;
80 interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>;
81 #address-cells = <1>;
82 #size-cells = <0>;
83 #io-channel-cells = <1>;
84
85 channel@7 {
86 reg = <VADC_VSYS>;
87 qcom,pre-scaling = <1 3>;
88 label = "vph_pwr";
89 };
90 channel@8 {
91 reg = <VADC_DIE_TEMP>;
92 label = "die_temp";
93 };
94 channel@9 {
95 reg = <VADC_REF_625MV>;
96 label = "ref_625mv";
97 };
98 channel@a {
99 reg = <VADC_REF_1250MV>;
100 label = "ref_1250mv";
101 };
102 channel@e {
103 reg = <VADC_GND_REF>;
104 };
105 channel@f {
106 reg = <VADC_VDD_VADC>;
107 };
108 };
109
110 pm8994_gpios: gpio@c000 {
111 compatible = "qcom,pm8994-gpio", "qcom,spmi-gpio";
112 reg = <0xc000>;
113 gpio-controller;
114 gpio-ranges = <&pm8994_gpios 0 0 22>;
115 #gpio-cells = <2>;
116 interrupt-controller;
117 #interrupt-cells = <2>;
118 };
119
120 pm8994_mpps: mpps@a000 {
121 compatible = "qcom,pm8994-mpp", "qcom,spmi-mpp";
122 reg = <0xa000>;
123 gpio-controller;
124 #gpio-cells = <2>;
125 gpio-ranges = <&pm8994_mpps 0 0 8>;
126 interrupt-controller;
127 #interrupt-cells = <2>;
128 };
129 };
130
131 pmic@1 {
132 compatible = "qcom,pm8994", "qcom,spmi-pmic";
133 reg = <0x1 SPMI_USID>;
134 #address-cells = <1>;
135 #size-cells = <0>;
136
137 pm8994_lpg: pwm {
138 compatible = "qcom,pm8994-lpg";
139
140 #address-cells = <1>;
141 #size-cells = <0>;
142 #pwm-cells = <2>;
143
144 status = "disabled";
145 };
146
147 pm8994_spmi_regulators: regulators {
148 compatible = "qcom,pm8994-regulators";
149 };
150 };
151 };