Debian Codegraph @

scripts/dtc/include-prefixes/arm64/qcom/pm8937.dtsi

raw
1 // SPDX-License-Identifier: BSD-3-Clause
2 /*
3 * Copyright (c) 2023, Dang Huynh <[email protected]>
4 */
5
6 #include <dt-bindings/iio/qcom,spmi-vadc.h>
7 #include <dt-bindings/input/linux-event-codes.h>
8 #include <dt-bindings/spmi/spmi.h>
9
10 / {
11 thermal-zones {
12 pm8937-thermal {
13 polling-delay-passive = <0>;
14 polling-delay = <0>;
15 thermal-sensors = <&pm8937_temp>;
16
17 trips {
18 trip0 {
19 temperature = <105000>;
20 hysteresis = <0>;
21 type = "passive";
22 };
23
24 trip1 {
25 temperature = <125000>;
26 hysteresis = <0>;
27 type = "hot";
28 };
29
30 trip2 {
31 temperature = <145000>;
32 hysteresis = <0>;
33 type = "critical";
34 };
35 };
36 };
37 };
38 };
39
40 &spmi_bus {
41 pmic@0 {
42 compatible = "qcom,pm8937", "qcom,spmi-pmic";
43 reg = <0x0 SPMI_USID>;
44 #address-cells = <1>;
45 #size-cells = <0>;
46
47 pon@800 {
48 compatible = "qcom,pm8916-pon";
49 reg = <0x800>;
50 mode-bootloader = <0x2>;
51 mode-recovery = <0x1>;
52
53 pm8937_pwrkey: pwrkey {
54 compatible = "qcom,pm8941-pwrkey";
55 interrupts = <0 0x8 0 IRQ_TYPE_EDGE_BOTH>;
56 debounce = <15625>;
57 bias-pull-up;
58 linux,code = <KEY_POWER>;
59 };
60
61 pm8937_resin: resin {
62 compatible = "qcom,pm8941-resin";
63 interrupts = <0 0x8 1 IRQ_TYPE_EDGE_BOTH>;
64 debounce = <15625>;
65 bias-pull-up;
66 status = "disabled";
67 };
68 };
69
70 pm8937_gpios: gpio@c000 {
71 compatible = "qcom,pm8937-gpio", "qcom,spmi-gpio";
72 reg = <0xc000>;
73 gpio-controller;
74 gpio-ranges = <&pm8937_gpios 0 0 8>;
75 #gpio-cells = <2>;
76 interrupt-controller;
77 #interrupt-cells = <2>;
78 };
79
80 pm8937_mpps: mpps@a000 {
81 compatible = "qcom,pm8937-mpp", "qcom,spmi-mpp";
82 reg = <0xa000>;
83 gpio-controller;
84 gpio-ranges = <&pm8937_mpps 0 0 4>;
85 #gpio-cells = <2>;
86 interrupt-controller;
87 #interrupt-cells = <2>;
88 };
89
90 pm8937_temp: temp-alarm@2400 {
91 compatible = "qcom,spmi-temp-alarm";
92 reg = <0x2400>;
93 interrupts = <0 0x24 0 IRQ_TYPE_EDGE_RISING>;
94 io-channels = <&pm8937_vadc VADC_DIE_TEMP>;
95 io-channel-names = "thermal";
96 #thermal-sensor-cells = <0>;
97 };
98
99 pm8937_vadc: adc@3100 {
100 compatible = "qcom,spmi-vadc";
101 reg = <0x3100>;
102 interrupts = <0 0x31 0 IRQ_TYPE_EDGE_RISING>;
103 #address-cells = <1>;
104 #size-cells = <0>;
105 #io-channel-cells = <1>;
106
107 channel@8 {
108 reg = <VADC_DIE_TEMP>;
109 };
110
111 channel@9 {
112 reg = <VADC_REF_625MV>;
113 };
114
115 channel@a {
116 reg = <VADC_REF_1250MV>;
117 };
118
119 channel@c {
120 reg = <VADC_SPARE1>;
121 };
122
123 channel@e {
124 reg = <VADC_GND_REF>;
125 };
126
127 channel@f {
128 reg = <VADC_VDD_VADC>;
129 };
130 };
131
132 rtc@6000 {
133 compatible = "qcom,pm8941-rtc";
134 reg = <0x6000>, <0x6100>;
135 reg-names = "rtc", "alarm";
136 interrupts = <0x0 0x61 0x1 IRQ_TYPE_EDGE_RISING>;
137 };
138 };
139
140 pmic@1 {
141 compatible = "qcom,pm8937", "qcom,spmi-pmic";
142 reg = <0x1 SPMI_USID>;
143 #address-cells = <1>;
144 #size-cells = <0>;
145
146 pm8937_pwm: pwm {
147 compatible = "qcom,pm8937-pwm", "qcom,pm8916-pwm";
148
149 #pwm-cells = <2>;
150
151 status = "disabled";
152 };
153
154 pm8937_spmi_regulators: regulators {
155 compatible = "qcom,pm8937-regulators";
156 };
157 };
158 };