| 1 |
// SPDX-License-Identifier: BSD-3-Clause |
| 2 |
/* |
| 3 |
* Copyright (c) 2017-2019, The Linux Foundation. All rights reserved. |
| 4 |
* Copyright (c) 2019, Linaro Limited |
| 5 |
*/ |
| 6 |
|
| 7 |
#include <dt-bindings/input/input.h> |
| 8 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 9 |
#include <dt-bindings/spmi/spmi.h> |
| 10 |
#include <dt-bindings/iio/qcom,spmi-vadc.h> |
| 11 |
|
| 12 |
/ { |
| 13 |
thermal-zones { |
| 14 |
pm8150-thermal { |
| 15 |
polling-delay-passive = <100>; |
| 16 |
|
| 17 |
thermal-sensors = <&pm8150_temp>; |
| 18 |
|
| 19 |
trips { |
| 20 |
trip0 { |
| 21 |
temperature = <95000>; |
| 22 |
hysteresis = <0>; |
| 23 |
type = "passive"; |
| 24 |
}; |
| 25 |
|
| 26 |
trip1 { |
| 27 |
temperature = <115000>; |
| 28 |
hysteresis = <0>; |
| 29 |
type = "hot"; |
| 30 |
}; |
| 31 |
|
| 32 |
trip2 { |
| 33 |
temperature = <145000>; |
| 34 |
hysteresis = <0>; |
| 35 |
type = "critical"; |
| 36 |
}; |
| 37 |
}; |
| 38 |
}; |
| 39 |
}; |
| 40 |
}; |
| 41 |
|
| 42 |
&spmi_bus { |
| 43 |
pm8150_0: pmic@0 { |
| 44 |
compatible = "qcom,pm8150", "qcom,spmi-pmic"; |
| 45 |
reg = <0x0 SPMI_USID>; |
| 46 |
#address-cells = <1>; |
| 47 |
#size-cells = <0>; |
| 48 |
|
| 49 |
pon: pon@800 { |
| 50 |
compatible = "qcom,pm8998-pon"; |
| 51 |
reg = <0x0800>; |
| 52 |
|
| 53 |
pon_pwrkey: pwrkey { |
| 54 |
compatible = "qcom,pm8941-pwrkey"; |
| 55 |
interrupts = <0x0 0x8 0x0 IRQ_TYPE_EDGE_BOTH>; |
| 56 |
debounce = <15625>; |
| 57 |
bias-pull-up; |
| 58 |
linux,code = <KEY_POWER>; |
| 59 |
|
| 60 |
status = "disabled"; |
| 61 |
}; |
| 62 |
|
| 63 |
pon_resin: resin { |
| 64 |
compatible = "qcom,pm8941-resin"; |
| 65 |
interrupts = <0x0 0x8 0x1 IRQ_TYPE_EDGE_BOTH>; |
| 66 |
debounce = <15625>; |
| 67 |
bias-pull-up; |
| 68 |
|
| 69 |
status = "disabled"; |
| 70 |
}; |
| 71 |
}; |
| 72 |
|
| 73 |
pm8150_temp: temp-alarm@2400 { |
| 74 |
compatible = "qcom,spmi-temp-alarm"; |
| 75 |
reg = <0x2400>; |
| 76 |
interrupts = <0x0 0x24 0x0 IRQ_TYPE_EDGE_BOTH>; |
| 77 |
io-channels = <&pm8150_adc ADC5_DIE_TEMP>; |
| 78 |
io-channel-names = "thermal"; |
| 79 |
#thermal-sensor-cells = <0>; |
| 80 |
}; |
| 81 |
|
| 82 |
pm8150_adc: adc@3100 { |
| 83 |
compatible = "qcom,spmi-adc5"; |
| 84 |
reg = <0x3100>; |
| 85 |
#address-cells = <1>; |
| 86 |
#size-cells = <0>; |
| 87 |
#io-channel-cells = <1>; |
| 88 |
interrupts = <0x0 0x31 0x0 IRQ_TYPE_EDGE_RISING>; |
| 89 |
|
| 90 |
channel@0 { |
| 91 |
reg = <ADC5_REF_GND>; |
| 92 |
qcom,pre-scaling = <1 1>; |
| 93 |
label = "ref_gnd"; |
| 94 |
}; |
| 95 |
|
| 96 |
channel@1 { |
| 97 |
reg = <ADC5_1P25VREF>; |
| 98 |
qcom,pre-scaling = <1 1>; |
| 99 |
label = "vref_1p25"; |
| 100 |
}; |
| 101 |
|
| 102 |
channel@6 { |
| 103 |
reg = <ADC5_DIE_TEMP>; |
| 104 |
qcom,pre-scaling = <1 1>; |
| 105 |
label = "die_temp"; |
| 106 |
}; |
| 107 |
}; |
| 108 |
|
| 109 |
pm8150_adc_tm: adc-tm@3500 { |
| 110 |
compatible = "qcom,spmi-adc-tm5"; |
| 111 |
reg = <0x3500>; |
| 112 |
interrupts = <0x0 0x35 0x0 IRQ_TYPE_EDGE_RISING>; |
| 113 |
#thermal-sensor-cells = <1>; |
| 114 |
#address-cells = <1>; |
| 115 |
#size-cells = <0>; |
| 116 |
status = "disabled"; |
| 117 |
}; |
| 118 |
|
| 119 |
rtc@6000 { |
| 120 |
compatible = "qcom,pm8941-rtc"; |
| 121 |
reg = <0x6000>, <0x6100>; |
| 122 |
reg-names = "rtc", "alarm"; |
| 123 |
interrupts = <0x0 0x61 0x1 IRQ_TYPE_NONE>; |
| 124 |
}; |
| 125 |
|
| 126 |
pm8150_gpios: gpio@c000 { |
| 127 |
compatible = "qcom,pm8150-gpio", "qcom,spmi-gpio"; |
| 128 |
reg = <0xc000>; |
| 129 |
gpio-controller; |
| 130 |
gpio-ranges = <&pm8150_gpios 0 0 10>; |
| 131 |
#gpio-cells = <2>; |
| 132 |
interrupt-controller; |
| 133 |
#interrupt-cells = <2>; |
| 134 |
}; |
| 135 |
}; |
| 136 |
|
| 137 |
pmic@1 { |
| 138 |
compatible = "qcom,pm8150", "qcom,spmi-pmic"; |
| 139 |
reg = <0x1 SPMI_USID>; |
| 140 |
#address-cells = <1>; |
| 141 |
#size-cells = <0>; |
| 142 |
}; |
| 143 |
}; |