| 1 |
// SPDX-License-Identifier: BSD-3-Clause |
| 2 |
/* |
| 3 |
* OnePlus 5(T) (cheeseburger / dumpling) common device tree source based on msm8998-mtp.dtsi |
| 4 |
* |
| 5 |
* Copyright (c) 2021, Jami Kettunen <[email protected]> |
| 6 |
* Copyright (c) 2016, The Linux Foundation. All rights reserved. |
| 7 |
*/ |
| 8 |
|
| 9 |
/dts-v1/; |
| 10 |
|
| 11 |
#include <dt-bindings/gpio/gpio.h> |
| 12 |
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| 13 |
#include "msm8998.dtsi" |
| 14 |
#include "pm8005.dtsi" |
| 15 |
#include "pm8998.dtsi" |
| 16 |
#include "pmi8998.dtsi" |
| 17 |
|
| 18 |
/ { |
| 19 |
/* Required for bootloader to select correct board */ |
| 20 |
qcom,msm-id = <292 0x20001>; /* 8998 v2.1 */ |
| 21 |
|
| 22 |
chosen { |
| 23 |
#address-cells = <2>; |
| 24 |
#size-cells = <2>; |
| 25 |
ranges; |
| 26 |
|
| 27 |
/* Use display framebuffer setup by the UEFI XBL bootloader for simplefb */ |
| 28 |
framebuffer0: framebuffer@9d400000 { |
| 29 |
compatible = "simple-framebuffer"; |
| 30 |
reg = <0x0 0x9d400000 0x0 0x2400000>; |
| 31 |
width = <1080>; |
| 32 |
height = <1920>; |
| 33 |
stride = <(1080 * 4)>; |
| 34 |
format = "a8r8g8b8"; |
| 35 |
/* |
| 36 |
* That's a lot of clocks, but it's necessary due |
| 37 |
* to unused clk cleanup & no panel driver yet.. |
| 38 |
*/ |
| 39 |
clocks = <&mmcc MDSS_AHB_CLK>, |
| 40 |
<&mmcc MDSS_AXI_CLK>, |
| 41 |
<&mmcc MDSS_VSYNC_CLK>, |
| 42 |
<&mmcc MDSS_MDP_CLK>, |
| 43 |
<&mmcc MDSS_BYTE0_CLK>, |
| 44 |
<&mmcc MDSS_BYTE0_INTF_CLK>, |
| 45 |
<&mmcc MDSS_PCLK0_CLK>, |
| 46 |
<&mmcc MDSS_ESC0_CLK>; |
| 47 |
power-domains = <&mmcc MDSS_GDSC>; |
| 48 |
}; |
| 49 |
}; |
| 50 |
|
| 51 |
reserved-memory { |
| 52 |
/* Bootloader display framebuffer region */ |
| 53 |
cont_splash_mem: memory@9d400000 { |
| 54 |
reg = <0x0 0x9d400000 0x0 0x2400000>; |
| 55 |
no-map; |
| 56 |
}; |
| 57 |
|
| 58 |
/* For getting crash logs using Android downstream kernels */ |
| 59 |
ramoops@ac000000 { |
| 60 |
compatible = "ramoops"; |
| 61 |
reg = <0x0 0xac000000 0x0 0x200000>; |
| 62 |
console-size = <0x80000>; |
| 63 |
pmsg-size = <0x40000>; |
| 64 |
record-size = <0x8000>; |
| 65 |
ftrace-size = <0x20000>; |
| 66 |
}; |
| 67 |
|
| 68 |
/* |
| 69 |
* The following memory regions on downstream are "dynamically allocated" |
| 70 |
* but given the same addresses every time. Hard code them as these addresses |
| 71 |
* are where the OnePlus signed firmware expects them to be. |
| 72 |
*/ |
| 73 |
ipa_fws_region: ipa@f6800000 { |
| 74 |
compatible = "shared-dma-pool"; |
| 75 |
reg = <0x0 0xf6800000 0x0 0x5000>; |
| 76 |
no-map; |
| 77 |
}; |
| 78 |
zap_shader_region: gpu@f6900000 { |
| 79 |
compatible = "shared-dma-pool"; |
| 80 |
reg = <0x0 0xf6900000 0x0 0x2000>; |
| 81 |
no-map; |
| 82 |
}; |
| 83 |
}; |
| 84 |
|
| 85 |
gpio-keys { |
| 86 |
compatible = "gpio-keys"; |
| 87 |
label = "Volume buttons"; |
| 88 |
autorepeat; |
| 89 |
|
| 90 |
pinctrl-names = "default"; |
| 91 |
pinctrl-0 = <&vol_keys_default>; |
| 92 |
|
| 93 |
button-vol-down { |
| 94 |
label = "Volume down"; |
| 95 |
gpios = <&pm8998_gpios 5 GPIO_ACTIVE_LOW>; |
| 96 |
linux,code = <KEY_VOLUMEDOWN>; |
| 97 |
debounce-interval = <15>; |
| 98 |
wakeup-source; |
| 99 |
}; |
| 100 |
|
| 101 |
button-vol-up { |
| 102 |
label = "Volume up"; |
| 103 |
gpios = <&pm8998_gpios 6 GPIO_ACTIVE_LOW>; |
| 104 |
linux,code = <KEY_VOLUMEUP>; |
| 105 |
debounce-interval = <15>; |
| 106 |
wakeup-source; |
| 107 |
}; |
| 108 |
}; |
| 109 |
|
| 110 |
gpio-hall-sensor { |
| 111 |
compatible = "gpio-keys"; |
| 112 |
label = "Hall effect sensor"; |
| 113 |
|
| 114 |
pinctrl-names = "default"; |
| 115 |
pinctrl-0 = <&hall_sensor_default>; |
| 116 |
|
| 117 |
event-hall-sensor { |
| 118 |
label = "Hall Effect Sensor"; |
| 119 |
gpios = <&tlmm 124 GPIO_ACTIVE_LOW>; |
| 120 |
linux,input-type = <EV_SW>; |
| 121 |
linux,code = <SW_LID>; |
| 122 |
linux,can-disable; |
| 123 |
wakeup-source; |
| 124 |
}; |
| 125 |
}; |
| 126 |
|
| 127 |
vph_pwr: vph-pwr-regulator { |
| 128 |
compatible = "regulator-fixed"; |
| 129 |
regulator-name = "vph_pwr"; |
| 130 |
regulator-always-on; |
| 131 |
regulator-boot-on; |
| 132 |
}; |
| 133 |
}; |
| 134 |
|
| 135 |
/* |
| 136 |
* OnePlus' ADSP firmware requires 30 MiB in total, so increase the adsp_mem |
| 137 |
* region by 4 MiB to account for this while relocating the other now |
| 138 |
* conflicting memory nodes accordingly. |
| 139 |
*/ |
| 140 |
&adsp_mem { |
| 141 |
reg = <0x0 0x8b200000 0x0 0x1e00000>; |
| 142 |
}; |
| 143 |
&mpss_mem { |
| 144 |
reg = <0x0 0x8d000000 0x0 0x7000000>; |
| 145 |
}; |
| 146 |
&venus_mem { |
| 147 |
reg = <0x0 0x94000000 0x0 0x500000>; |
| 148 |
}; |
| 149 |
&mba_mem { |
| 150 |
reg = <0x0 0x94500000 0x0 0x200000>; |
| 151 |
}; |
| 152 |
&slpi_mem { |
| 153 |
reg = <0x0 0x94700000 0x0 0xf00000>; |
| 154 |
}; |
| 155 |
&ipa_fw_mem { |
| 156 |
reg = <0x0 0x95600000 0x0 0x10000>; |
| 157 |
}; |
| 158 |
&ipa_gsi_mem { |
| 159 |
reg = <0x0 0x95610000 0x0 0x5000>; |
| 160 |
}; |
| 161 |
&gpu_mem { |
| 162 |
reg = <0x0 0x95615000 0x0 0x100000>; |
| 163 |
}; |
| 164 |
&wlan_msa_mem { |
| 165 |
reg = <0x0 0x95715000 0x0 0x100000>; |
| 166 |
}; |
| 167 |
|
| 168 |
&blsp1_i2c5 { |
| 169 |
status = "okay"; |
| 170 |
|
| 171 |
touchscreen@20 { |
| 172 |
compatible = "syna,rmi4-i2c"; |
| 173 |
reg = <0x20>; |
| 174 |
#address-cells = <1>; |
| 175 |
#size-cells = <0>; |
| 176 |
|
| 177 |
interrupt-parent = <&tlmm>; |
| 178 |
interrupts = <125 IRQ_TYPE_EDGE_FALLING>; |
| 179 |
|
| 180 |
pinctrl-names = "default"; |
| 181 |
pinctrl-0 = <&ts_int_active &ts_reset_active>; |
| 182 |
|
| 183 |
vdd-supply = <&vreg_l28_3p0>; |
| 184 |
vio-supply = <&vreg_l6a_1p8>; |
| 185 |
|
| 186 |
syna,reset-delay-ms = <20>; |
| 187 |
syna,startup-delay-ms = <20>; |
| 188 |
|
| 189 |
rmi4-f01@1 { |
| 190 |
reg = <0x01>; |
| 191 |
syna,nosleep-mode = <1>; |
| 192 |
}; |
| 193 |
|
| 194 |
rmi4_f12: rmi4-f12@12 { |
| 195 |
reg = <0x12>; |
| 196 |
syna,rezero-wait-ms = <20>; |
| 197 |
syna,sensor-type = <1>; |
| 198 |
touchscreen-x-mm = <68>; |
| 199 |
touchscreen-y-mm = <122>; |
| 200 |
}; |
| 201 |
}; |
| 202 |
}; |
| 203 |
|
| 204 |
&blsp1_i2c6 { |
| 205 |
status = "okay"; |
| 206 |
|
| 207 |
nfc@28 { |
| 208 |
compatible = "nxp,nxp-nci-i2c"; |
| 209 |
reg = <0x28>; |
| 210 |
|
| 211 |
interrupt-parent = <&tlmm>; |
| 212 |
interrupts = <92 IRQ_TYPE_LEVEL_HIGH>; |
| 213 |
|
| 214 |
enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>; |
| 215 |
|
| 216 |
pinctrl-names = "default"; |
| 217 |
pinctrl-0 = <&nfc_int_active &nfc_enable_active>; |
| 218 |
}; |
| 219 |
}; |
| 220 |
|
| 221 |
&blsp1_uart3 { |
| 222 |
status = "okay"; |
| 223 |
|
| 224 |
bluetooth { |
| 225 |
compatible = "qcom,wcn3990-bt"; |
| 226 |
|
| 227 |
vddio-supply = <&vreg_s4a_1p8>; |
| 228 |
vddxo-supply = <&vreg_l7a_1p8>; |
| 229 |
vddrf-supply = <&vreg_l17a_1p3>; |
| 230 |
vddch0-supply = <&vreg_l25a_3p3>; |
| 231 |
max-speed = <3200000>; |
| 232 |
}; |
| 233 |
}; |
| 234 |
|
| 235 |
&blsp1_uart3_on { |
| 236 |
rx-pins { |
| 237 |
/delete-property/ bias-disable; |
| 238 |
/* |
| 239 |
* Configure a pull-up on 46 (RX). This is needed to |
| 240 |
* avoid garbage data when the TX pin of the Bluetooth |
| 241 |
* module is in tri-state (module powered off or not |
| 242 |
* driving the signal yet). |
| 243 |
*/ |
| 244 |
bias-pull-up; |
| 245 |
}; |
| 246 |
|
| 247 |
cts-pins { |
| 248 |
/delete-property/ bias-disable; |
| 249 |
/* |
| 250 |
* Configure a pull-down on 47 (CTS) to match the pull |
| 251 |
* of the Bluetooth module. |
| 252 |
*/ |
| 253 |
bias-pull-down; |
| 254 |
}; |
| 255 |
}; |
| 256 |
|
| 257 |
&blsp2_uart1 { |
| 258 |
status = "okay"; |
| 259 |
}; |
| 260 |
|
| 261 |
&pm8005_regulators { |
| 262 |
/* VDD_GFX supply */ |
| 263 |
pm8005_s1: s1 { |
| 264 |
regulator-min-microvolt = <524000>; |
| 265 |
regulator-max-microvolt = <1100000>; |
| 266 |
regulator-enable-ramp-delay = <500>; |
| 267 |
/* Hack until we rig up the gpu consumer */ |
| 268 |
regulator-always-on; |
| 269 |
}; |
| 270 |
}; |
| 271 |
|
| 272 |
&pm8998_gpios { |
| 273 |
vol_keys_default: vol-keys-state { |
| 274 |
pins = "gpio5", "gpio6"; |
| 275 |
function = "normal"; |
| 276 |
bias-pull-up; |
| 277 |
input-enable; |
| 278 |
qcom,drive-strength = <PMIC_GPIO_STRENGTH_NO>; |
| 279 |
}; |
| 280 |
}; |
| 281 |
|
| 282 |
&qusb2phy { |
| 283 |
status = "okay"; |
| 284 |
|
| 285 |
vdd-supply = <&vreg_l1a_0p875>; |
| 286 |
vdda-pll-supply = <&vreg_l12a_1p8>; |
| 287 |
vdda-phy-dpdm-supply = <&vreg_l24a_3p075>; |
| 288 |
}; |
| 289 |
|
| 290 |
&rpm_requests { |
| 291 |
regulators-0 { |
| 292 |
compatible = "qcom,rpm-pm8998-regulators"; |
| 293 |
|
| 294 |
vdd_s1-supply = <&vph_pwr>; |
| 295 |
vdd_s2-supply = <&vph_pwr>; |
| 296 |
vdd_s3-supply = <&vph_pwr>; |
| 297 |
vdd_s4-supply = <&vph_pwr>; |
| 298 |
vdd_s5-supply = <&vph_pwr>; |
| 299 |
vdd_s6-supply = <&vph_pwr>; |
| 300 |
vdd_s7-supply = <&vph_pwr>; |
| 301 |
vdd_s8-supply = <&vph_pwr>; |
| 302 |
vdd_s9-supply = <&vph_pwr>; |
| 303 |
vdd_s10-supply = <&vph_pwr>; |
| 304 |
vdd_s11-supply = <&vph_pwr>; |
| 305 |
vdd_s12-supply = <&vph_pwr>; |
| 306 |
vdd_s13-supply = <&vph_pwr>; |
| 307 |
vdd_l1_l27-supply = <&vreg_s7a_1p025>; |
| 308 |
vdd_l2_l8_l17-supply = <&vreg_s3a_1p35>; |
| 309 |
vdd_l3_l11-supply = <&vreg_s7a_1p025>; |
| 310 |
vdd_l4_l5-supply = <&vreg_s7a_1p025>; |
| 311 |
vdd_l6-supply = <&vreg_s5a_2p04>; |
| 312 |
vdd_l7_l12_l14_l15-supply = <&vreg_s5a_2p04>; |
| 313 |
vdd_l9-supply = <&vreg_bob>; |
| 314 |
vdd_l10_l23_l25-supply = <&vreg_bob>; |
| 315 |
vdd_l13_l19_l21-supply = <&vreg_bob>; |
| 316 |
vdd_l16_l28-supply = <&vreg_bob>; |
| 317 |
vdd_l18_l22-supply = <&vreg_bob>; |
| 318 |
vdd_l20_l24-supply = <&vreg_bob>; |
| 319 |
vdd_l26-supply = <&vreg_s3a_1p35>; |
| 320 |
vdd_lvs1_lvs2-supply = <&vreg_s4a_1p8>; |
| 321 |
|
| 322 |
vreg_s3a_1p35: s3 { |
| 323 |
regulator-min-microvolt = <1352000>; |
| 324 |
regulator-max-microvolt = <1352000>; |
| 325 |
}; |
| 326 |
|
| 327 |
vreg_s4a_1p8: s4 { |
| 328 |
regulator-min-microvolt = <1800000>; |
| 329 |
regulator-max-microvolt = <1800000>; |
| 330 |
regulator-allow-set-load; |
| 331 |
}; |
| 332 |
|
| 333 |
vreg_s5a_2p04: s5 { |
| 334 |
regulator-min-microvolt = <1904000>; |
| 335 |
regulator-max-microvolt = <2040000>; |
| 336 |
}; |
| 337 |
|
| 338 |
vreg_s7a_1p025: s7 { |
| 339 |
regulator-min-microvolt = <900000>; |
| 340 |
regulator-max-microvolt = <1028000>; |
| 341 |
}; |
| 342 |
|
| 343 |
vreg_l1a_0p875: l1 { |
| 344 |
regulator-min-microvolt = <880000>; |
| 345 |
regulator-max-microvolt = <880000>; |
| 346 |
}; |
| 347 |
|
| 348 |
vreg_l2a_1p2: l2 { |
| 349 |
regulator-min-microvolt = <1200000>; |
| 350 |
regulator-max-microvolt = <1200000>; |
| 351 |
}; |
| 352 |
|
| 353 |
vreg_l3a_1p0: l3 { |
| 354 |
regulator-min-microvolt = <1000000>; |
| 355 |
regulator-max-microvolt = <1000000>; |
| 356 |
}; |
| 357 |
|
| 358 |
vreg_l5a_0p8: l5 { |
| 359 |
regulator-min-microvolt = <800000>; |
| 360 |
regulator-max-microvolt = <800000>; |
| 361 |
}; |
| 362 |
|
| 363 |
vreg_l6a_1p8: l6 { |
| 364 |
regulator-min-microvolt = <1808000>; |
| 365 |
regulator-max-microvolt = <1808000>; |
| 366 |
}; |
| 367 |
|
| 368 |
vreg_l7a_1p8: l7 { |
| 369 |
regulator-min-microvolt = <1800000>; |
| 370 |
regulator-max-microvolt = <1800000>; |
| 371 |
}; |
| 372 |
|
| 373 |
vreg_l8a_1p2: l8 { |
| 374 |
regulator-min-microvolt = <1200000>; |
| 375 |
regulator-max-microvolt = <1200000>; |
| 376 |
}; |
| 377 |
|
| 378 |
vreg_l9a_1p8: l9 { |
| 379 |
regulator-min-microvolt = <1808000>; |
| 380 |
regulator-max-microvolt = <2960000>; |
| 381 |
}; |
| 382 |
|
| 383 |
vreg_l10a_1p8: l10 { |
| 384 |
regulator-min-microvolt = <1808000>; |
| 385 |
regulator-max-microvolt = <2960000>; |
| 386 |
}; |
| 387 |
|
| 388 |
vreg_l11a_1p0: l11 { |
| 389 |
regulator-min-microvolt = <1000000>; |
| 390 |
regulator-max-microvolt = <1000000>; |
| 391 |
}; |
| 392 |
|
| 393 |
vreg_l12a_1p8: l12 { |
| 394 |
regulator-min-microvolt = <1800000>; |
| 395 |
regulator-max-microvolt = <1800000>; |
| 396 |
}; |
| 397 |
|
| 398 |
vreg_l13a_2p95: l13 { |
| 399 |
regulator-min-microvolt = <1808000>; |
| 400 |
regulator-max-microvolt = <2960000>; |
| 401 |
}; |
| 402 |
|
| 403 |
vreg_l14a_1p88: l14 { |
| 404 |
regulator-min-microvolt = <1880000>; |
| 405 |
regulator-max-microvolt = <1880000>; |
| 406 |
}; |
| 407 |
|
| 408 |
vreg_l15a_1p8: l15 { |
| 409 |
regulator-min-microvolt = <1800000>; |
| 410 |
regulator-max-microvolt = <1800000>; |
| 411 |
}; |
| 412 |
|
| 413 |
vreg_l16a_2p7: l16 { |
| 414 |
regulator-min-microvolt = <2704000>; |
| 415 |
regulator-max-microvolt = <2704000>; |
| 416 |
}; |
| 417 |
|
| 418 |
vreg_l17a_1p3: l17 { |
| 419 |
regulator-min-microvolt = <1304000>; |
| 420 |
regulator-max-microvolt = <1304000>; |
| 421 |
}; |
| 422 |
|
| 423 |
vreg_l18a_2p7: l18 { |
| 424 |
regulator-min-microvolt = <2704000>; |
| 425 |
regulator-max-microvolt = <2704000>; |
| 426 |
}; |
| 427 |
|
| 428 |
vreg_l19a_3p0: l19 { |
| 429 |
regulator-min-microvolt = <3008000>; |
| 430 |
regulator-max-microvolt = <3008000>; |
| 431 |
}; |
| 432 |
|
| 433 |
vreg_l20a_2p95: l20 { |
| 434 |
regulator-min-microvolt = <2960000>; |
| 435 |
regulator-max-microvolt = <2960000>; |
| 436 |
regulator-allow-set-load; |
| 437 |
}; |
| 438 |
vreg_l21a_2p95: l21 { |
| 439 |
regulator-min-microvolt = <2960000>; |
| 440 |
regulator-max-microvolt = <2960000>; |
| 441 |
regulator-system-load = <800000>; |
| 442 |
regulator-allow-set-load; |
| 443 |
}; |
| 444 |
|
| 445 |
vreg_l22a_2p85: l22 { |
| 446 |
regulator-min-microvolt = <2864000>; |
| 447 |
regulator-max-microvolt = <2864000>; |
| 448 |
}; |
| 449 |
|
| 450 |
vreg_l23a_3p3: l23 { |
| 451 |
regulator-min-microvolt = <3312000>; |
| 452 |
regulator-max-microvolt = <3312000>; |
| 453 |
}; |
| 454 |
|
| 455 |
vreg_l24a_3p075: l24 { |
| 456 |
regulator-min-microvolt = <3088000>; |
| 457 |
regulator-max-microvolt = <3088000>; |
| 458 |
}; |
| 459 |
|
| 460 |
vreg_l25a_3p3: l25 { |
| 461 |
regulator-min-microvolt = <3104000>; |
| 462 |
regulator-max-microvolt = <3312000>; |
| 463 |
}; |
| 464 |
|
| 465 |
vreg_l26a_1p2: l26 { |
| 466 |
regulator-min-microvolt = <1200000>; |
| 467 |
regulator-max-microvolt = <1200000>; |
| 468 |
regulator-allow-set-load; |
| 469 |
}; |
| 470 |
|
| 471 |
vreg_l28_3p0: l28 { |
| 472 |
regulator-min-microvolt = <3008000>; |
| 473 |
regulator-max-microvolt = <3008000>; |
| 474 |
}; |
| 475 |
|
| 476 |
vreg_lvs1a_1p8: lvs1 { }; |
| 477 |
vreg_lvs2a_1p8: lvs2 { }; |
| 478 |
}; |
| 479 |
|
| 480 |
regulators-1 { |
| 481 |
compatible = "qcom,rpm-pmi8998-regulators"; |
| 482 |
|
| 483 |
vdd_bob-supply = <&vph_pwr>; |
| 484 |
|
| 485 |
vreg_bob: bob { |
| 486 |
regulator-min-microvolt = <3312000>; |
| 487 |
regulator-max-microvolt = <3600000>; |
| 488 |
}; |
| 489 |
}; |
| 490 |
}; |
| 491 |
|
| 492 |
&tlmm { |
| 493 |
gpio-reserved-ranges = <0 4>, <81 4>; |
| 494 |
|
| 495 |
hall_sensor_default: hall-sensor-default-state { |
| 496 |
pins = "gpio124"; |
| 497 |
function = "gpio"; |
| 498 |
drive-strength = <2>; |
| 499 |
bias-disable; |
| 500 |
}; |
| 501 |
|
| 502 |
ts_int_active: ts-int-active-state { |
| 503 |
pins = "gpio125"; |
| 504 |
function = "gpio"; |
| 505 |
drive-strength = <8>; |
| 506 |
bias-pull-up; |
| 507 |
}; |
| 508 |
|
| 509 |
ts_reset_active: ts-reset-active-state { |
| 510 |
pins = "gpio89"; |
| 511 |
function = "gpio"; |
| 512 |
drive-strength = <8>; |
| 513 |
bias-pull-up; |
| 514 |
}; |
| 515 |
|
| 516 |
nfc_int_active: nfc-int-active-state { |
| 517 |
pins = "gpio92"; |
| 518 |
function = "gpio"; |
| 519 |
drive-strength = <6>; |
| 520 |
bias-pull-up; |
| 521 |
}; |
| 522 |
|
| 523 |
nfc_enable_active: nfc-enable-active-state { |
| 524 |
pins = "gpio12", "gpio116"; |
| 525 |
function = "gpio"; |
| 526 |
drive-strength = <6>; |
| 527 |
bias-pull-up; |
| 528 |
}; |
| 529 |
}; |
| 530 |
|
| 531 |
&ufshc { |
| 532 |
status = "okay"; |
| 533 |
|
| 534 |
vcc-supply = <&vreg_l20a_2p95>; |
| 535 |
vccq-supply = <&vreg_l26a_1p2>; |
| 536 |
vccq2-supply = <&vreg_s4a_1p8>; |
| 537 |
vdd-hba-supply = <&vreg_l26a_1p2>; |
| 538 |
vcc-max-microamp = <750000>; |
| 539 |
vccq-max-microamp = <560000>; |
| 540 |
vccq2-max-microamp = <750000>; |
| 541 |
}; |
| 542 |
|
| 543 |
&ufsphy { |
| 544 |
status = "okay"; |
| 545 |
|
| 546 |
vdda-phy-supply = <&vreg_l1a_0p875>; |
| 547 |
vdda-pll-supply = <&vreg_l2a_1p2>; |
| 548 |
}; |
| 549 |
|
| 550 |
&usb3 { |
| 551 |
status = "okay"; |
| 552 |
|
| 553 |
/* Disable USB3 clock requirement as the device only supports USB2 */ |
| 554 |
qcom,select-utmi-as-pipe-clk; |
| 555 |
}; |
| 556 |
|
| 557 |
&usb3_dwc3 { |
| 558 |
/* Drop the unused USB 3 PHY */ |
| 559 |
phys = <&qusb2phy>; |
| 560 |
phy-names = "usb2-phy"; |
| 561 |
|
| 562 |
/* Fastest mode for USB 2 */ |
| 563 |
maximum-speed = "high-speed"; |
| 564 |
|
| 565 |
/* Force to peripheral until we can switch modes */ |
| 566 |
dr_mode = "peripheral"; |
| 567 |
}; |
| 568 |
|
| 569 |
&wifi { |
| 570 |
/* Leave disabled until MSS is functional */ |
| 571 |
vdd-0.8-cx-mx-supply = <&vreg_l5a_0p8>; |
| 572 |
vdd-1.8-xo-supply = <&vreg_l7a_1p8>; |
| 573 |
vdd-1.3-rfa-supply = <&vreg_l17a_1p3>; |
| 574 |
vdd-3.3-ch0-supply = <&vreg_l25a_3p3>; |
| 575 |
}; |