| 1 |
// SPDX-License-Identifier: BSD-3-Clause |
| 2 |
/* |
| 3 |
* Copyright (c) 2020, Konrad Dybcio <[email protected]> |
| 4 |
*/ |
| 5 |
|
| 6 |
#include "msm8994.dtsi" |
| 7 |
#include "pm8994.dtsi" |
| 8 |
#include "pmi8994.dtsi" |
| 9 |
#include <dt-bindings/gpio/gpio.h> |
| 10 |
#include <dt-bindings/input/gpio-keys.h> |
| 11 |
|
| 12 |
/ { |
| 13 |
/* required for bootloader to select correct board */ |
| 14 |
|
| 15 |
/* |
| 16 |
* We support MSM8994 v2 (0x20000) and v2.1 (0x20001). |
| 17 |
* The V1 chip (0x0 and 0x10000) is significantly different |
| 18 |
* and requires driver-side changes (including CPR, be warned!!). |
| 19 |
* Besides that, it's very rare. |
| 20 |
*/ |
| 21 |
qcom,msm-id = <207 0x20000>, <207 0x20001>; |
| 22 |
/* We only use pm8994+pmi8994. */ |
| 23 |
qcom,pmic-id = <0x10009 0x1000a 0x00 0x00>; |
| 24 |
/* This property is shared across all kitakami devices. */ |
| 25 |
qcom,board-id = <8 0>; |
| 26 |
|
| 27 |
/* Kitakami firmware doesn't support PSCI */ |
| 28 |
/delete-node/ psci; |
| 29 |
|
| 30 |
gpio-keys { |
| 31 |
compatible = "gpio-keys"; |
| 32 |
autorepeat; |
| 33 |
|
| 34 |
button-0 { |
| 35 |
label = "Volume Down"; |
| 36 |
gpios = <&pm8994_gpios 2 GPIO_ACTIVE_LOW>; |
| 37 |
linux,input-type = <1>; |
| 38 |
linux,code = <KEY_VOLUMEDOWN>; |
| 39 |
wakeup-source; |
| 40 |
debounce-interval = <15>; |
| 41 |
}; |
| 42 |
|
| 43 |
button-1 { |
| 44 |
label = "Volume Up"; |
| 45 |
gpios = <&pm8994_gpios 3 GPIO_ACTIVE_LOW>; |
| 46 |
linux,input-type = <1>; |
| 47 |
linux,code = <KEY_VOLUMEUP>; |
| 48 |
wakeup-source; |
| 49 |
debounce-interval = <15>; |
| 50 |
}; |
| 51 |
|
| 52 |
button-2 { |
| 53 |
label = "Camera Snapshot"; |
| 54 |
gpios = <&pm8994_gpios 4 GPIO_ACTIVE_LOW>; |
| 55 |
linux,input-type = <1>; |
| 56 |
linux,code = <KEY_CAMERA>; |
| 57 |
wakeup-source; |
| 58 |
debounce-interval = <15>; |
| 59 |
}; |
| 60 |
|
| 61 |
button-3 { |
| 62 |
label = "Camera Focus"; |
| 63 |
gpios = <&pm8994_gpios 5 GPIO_ACTIVE_LOW>; |
| 64 |
linux,input-type = <1>; |
| 65 |
linux,code = <KEY_VOLUMEUP>; |
| 66 |
wakeup-source; |
| 67 |
debounce-interval = <15>; |
| 68 |
}; |
| 69 |
}; |
| 70 |
|
| 71 |
reserved-memory { |
| 72 |
/* This is for getting crash logs using Android downstream kernels */ |
| 73 |
ramoops@1fe00000 { |
| 74 |
compatible = "ramoops"; |
| 75 |
reg = <0 0x1fe00000 0 0x200000>; |
| 76 |
console-size = <0x100000>; |
| 77 |
record-size = <0x10000>; |
| 78 |
ftrace-size = <0x10000>; |
| 79 |
pmsg-size = <0x80000>; |
| 80 |
}; |
| 81 |
|
| 82 |
fb_region: fb@40000000 { |
| 83 |
reg = <0 0x40000000 0 0x1000000>; |
| 84 |
no-map; |
| 85 |
}; |
| 86 |
|
| 87 |
tzapp: memory@c7800000 { |
| 88 |
reg = <0 0xc7800000 0 0x1900000>; |
| 89 |
no-map; |
| 90 |
}; |
| 91 |
}; |
| 92 |
}; |
| 93 |
|
| 94 |
&blsp1_spi1 { |
| 95 |
status = "okay"; |
| 96 |
|
| 97 |
/* FPC fingerprint reader */ |
| 98 |
}; |
| 99 |
|
| 100 |
/* I2C1 is disabled on this board */ |
| 101 |
|
| 102 |
&blsp1_i2c2 { |
| 103 |
status = "okay"; |
| 104 |
clock-frequency = <355000>; |
| 105 |
|
| 106 |
/* NXP PN547 NFC */ |
| 107 |
}; |
| 108 |
|
| 109 |
&blsp1_i2c6 { |
| 110 |
status = "okay"; |
| 111 |
clock-frequency = <355000>; |
| 112 |
|
| 113 |
touchscreen: rmi4-i2c-dev@2c { |
| 114 |
compatible = "syna,rmi4-i2c"; |
| 115 |
reg = <0x2c>; |
| 116 |
#address-cells = <1>; |
| 117 |
#size-cells = <0>; |
| 118 |
|
| 119 |
interrupt-parent = <&tlmm>; |
| 120 |
interrupts = <42 IRQ_TYPE_EDGE_FALLING>; |
| 121 |
|
| 122 |
pinctrl-names = "default"; |
| 123 |
pinctrl-0 = <&ts_int_active &ts_reset_active>; |
| 124 |
|
| 125 |
vdd-supply = <&pm8994_l22>; |
| 126 |
vio-supply = <&pm8994_s4>; |
| 127 |
|
| 128 |
syna,reset-delay-ms = <220>; |
| 129 |
syna,startup-delay-ms = <220>; |
| 130 |
|
| 131 |
rmi4-f01@1 { |
| 132 |
reg = <0x01>; |
| 133 |
syna,nosleep-mode = <1>; |
| 134 |
}; |
| 135 |
|
| 136 |
rmi4-f11@11 { |
| 137 |
reg = <0x11>; |
| 138 |
syna,sensor-type = <1>; |
| 139 |
}; |
| 140 |
}; |
| 141 |
}; |
| 142 |
|
| 143 |
&blsp1_uart2 { |
| 144 |
status = "okay"; |
| 145 |
}; |
| 146 |
|
| 147 |
&blsp2_i2c5 { |
| 148 |
status = "okay"; |
| 149 |
clock-frequency = <355000>; |
| 150 |
|
| 151 |
/* sii8620 HDMI/MHL bridge */ |
| 152 |
}; |
| 153 |
|
| 154 |
&blsp2_uart2 { |
| 155 |
status = "okay"; |
| 156 |
}; |
| 157 |
|
| 158 |
/* |
| 159 |
* Kitakami bootloader only turns cont_splash on when it detects |
| 160 |
* specific downstream MDSS/backlight nodes in the active DTB. |
| 161 |
* One way to use that framebuffer is to load a secondary instance of |
| 162 |
* LK with the downstream DTB appended and then, only from there, load |
| 163 |
* mainline Linux. |
| 164 |
*/ |
| 165 |
&cont_splash_mem { |
| 166 |
reg = <0 0x03401000 0 0x2200000>; |
| 167 |
}; |
| 168 |
|
| 169 |
&pmi8994_spmi_regulators { |
| 170 |
/* |
| 171 |
* Yeah, this one *is* managed by RPMPD, but also needs |
| 172 |
* to be hacked up as a-o due to the GPU device only accepting a single |
| 173 |
* power domain.. which still isn't enough and forces us to bind |
| 174 |
* OXILI_CX and OXILI_GX together! |
| 175 |
*/ |
| 176 |
vdd_gfx: s2 { |
| 177 |
regulator-name = "VDD_GFX"; |
| 178 |
regulator-min-microvolt = <980000>; |
| 179 |
regulator-max-microvolt = <980000>; |
| 180 |
|
| 181 |
/* hack until we rig up the gpu consumer */ |
| 182 |
regulator-always-on; |
| 183 |
}; |
| 184 |
}; |
| 185 |
|
| 186 |
&rpm_requests { |
| 187 |
/* PMI8994 should probe first, because pmi8994_bby supplies some of PM8994's regulators */ |
| 188 |
pmi8994_regulators: regulators-0 { |
| 189 |
compatible = "qcom,rpm-pmi8994-regulators"; |
| 190 |
|
| 191 |
vdd_s1-supply = <&vph_pwr>; |
| 192 |
vdd_bst_byp-supply = <&vph_pwr>; |
| 193 |
|
| 194 |
pmi8994_s1: s1 { |
| 195 |
regulator-min-microvolt = <1025000>; |
| 196 |
regulator-max-microvolt = <1025000>; |
| 197 |
}; |
| 198 |
|
| 199 |
/* S2 & S3 - VDD_GFX */ |
| 200 |
|
| 201 |
pmi8994_bby: boost-bypass { |
| 202 |
regulator-min-microvolt = <3150000>; |
| 203 |
regulator-max-microvolt = <3600000>; |
| 204 |
}; |
| 205 |
}; |
| 206 |
|
| 207 |
pm8994_regulators: regulators-1 { |
| 208 |
compatible = "qcom,rpm-pm8994-regulators"; |
| 209 |
|
| 210 |
vdd_s3-supply = <&vph_pwr>; |
| 211 |
vdd_s4-supply = <&vph_pwr>; |
| 212 |
vdd_s5-supply = <&vph_pwr>; |
| 213 |
vdd_s6-supply = <&vph_pwr>; |
| 214 |
vdd_s7-supply = <&vph_pwr>; |
| 215 |
vdd_l1-supply = <&pmi8994_s1>; |
| 216 |
vdd_l2_l26_l28-supply = <&pm8994_s3>; |
| 217 |
vdd_l3_l11-supply = <&pm8994_s3>; |
| 218 |
vdd_l4_l27_l31-supply = <&pm8994_s3>; |
| 219 |
vdd_l6_l12_l32-supply = <&pm8994_s5>; |
| 220 |
vdd_l8_l16_l30-supply = <&vph_pwr>; |
| 221 |
vdd_l9_l10_l18_l22-supply = <&pmi8994_bby>; |
| 222 |
vdd_l13_l19_l23_l24-supply = <&pmi8994_bby>; |
| 223 |
vdd_l14_l15-supply = <&pm8994_s5>; |
| 224 |
vdd_l17_l29-supply = <&pmi8994_bby>; |
| 225 |
vdd_l20_l21-supply = <&pmi8994_bby>; |
| 226 |
vdd_l25-supply = <&pm8994_s3>; |
| 227 |
vdd_lvs1_2-supply = <&pm8994_s4>; |
| 228 |
|
| 229 |
/* S1, S2, S6 and S12 are managed by RPMPD */ |
| 230 |
|
| 231 |
pm8994_s3: s3 { |
| 232 |
regulator-min-microvolt = <1300000>; |
| 233 |
regulator-max-microvolt = <1300000>; |
| 234 |
}; |
| 235 |
|
| 236 |
pm8994_s4: s4 { |
| 237 |
regulator-min-microvolt = <1800000>; |
| 238 |
regulator-max-microvolt = <1800000>; |
| 239 |
regulator-system-load = <325000>; |
| 240 |
regulator-allow-set-load; |
| 241 |
regulator-always-on; |
| 242 |
}; |
| 243 |
|
| 244 |
pm8994_s5: s5 { |
| 245 |
regulator-min-microvolt = <2150000>; |
| 246 |
regulator-max-microvolt = <2150000>; |
| 247 |
}; |
| 248 |
|
| 249 |
pm8994_s7: s7 { |
| 250 |
regulator-min-microvolt = <1000000>; |
| 251 |
regulator-max-microvolt = <1000000>; |
| 252 |
}; |
| 253 |
|
| 254 |
/* |
| 255 |
* S8 - SPMI-managed VDD_APC0 |
| 256 |
* S9, S10 and S11 (the main one) - SPMI-managed VDD_APC1 |
| 257 |
*/ |
| 258 |
|
| 259 |
pm8994_l1: l1 { |
| 260 |
regulator-min-microvolt = <1000000>; |
| 261 |
regulator-max-microvolt = <1000000>; |
| 262 |
}; |
| 263 |
|
| 264 |
pm8994_l2: l2 { |
| 265 |
regulator-min-microvolt = <1250000>; |
| 266 |
regulator-max-microvolt = <1250000>; |
| 267 |
regulator-system-load = <10000>; |
| 268 |
regulator-allow-set-load; |
| 269 |
}; |
| 270 |
|
| 271 |
pm8994_l3: l3 { |
| 272 |
regulator-min-microvolt = <1100000>; |
| 273 |
regulator-max-microvolt = <1100000>; |
| 274 |
regulator-boot-on; |
| 275 |
}; |
| 276 |
|
| 277 |
pm8994_l4: l4 { |
| 278 |
regulator-min-microvolt = <1225000>; |
| 279 |
regulator-max-microvolt = <1225000>; |
| 280 |
}; |
| 281 |
|
| 282 |
/* L5 is inaccessible from RPM */ |
| 283 |
|
| 284 |
pm8994_l6: l6 { |
| 285 |
regulator-min-microvolt = <1800000>; |
| 286 |
regulator-max-microvolt = <1800000>; |
| 287 |
}; |
| 288 |
|
| 289 |
/* L7 is inaccessible from RPM */ |
| 290 |
|
| 291 |
pm8994_l8: l8 { |
| 292 |
regulator-min-microvolt = <1800000>; |
| 293 |
regulator-max-microvolt = <1800000>; |
| 294 |
}; |
| 295 |
|
| 296 |
pm8994_l9: l9 { |
| 297 |
regulator-min-microvolt = <1800000>; |
| 298 |
regulator-max-microvolt = <1800000>; |
| 299 |
}; |
| 300 |
|
| 301 |
pm8994_l10: l10 { |
| 302 |
regulator-min-microvolt = <1800000>; |
| 303 |
regulator-max-microvolt = <1800000>; |
| 304 |
}; |
| 305 |
|
| 306 |
pm8994_l11: l11 { |
| 307 |
regulator-min-microvolt = <1200000>; |
| 308 |
regulator-max-microvolt = <1200000>; |
| 309 |
}; |
| 310 |
|
| 311 |
pm8994_l12: l12 { |
| 312 |
regulator-min-microvolt = <1800000>; |
| 313 |
regulator-max-microvolt = <1800000>; |
| 314 |
regulator-system-load = <10000>; |
| 315 |
regulator-allow-set-load; |
| 316 |
}; |
| 317 |
|
| 318 |
pm8994_l13: l13 { |
| 319 |
regulator-min-microvolt = <1800000>; |
| 320 |
regulator-max-microvolt = <2950000>; |
| 321 |
}; |
| 322 |
|
| 323 |
pm8994_l14: l14 { |
| 324 |
regulator-min-microvolt = <1800000>; |
| 325 |
regulator-max-microvolt = <1800000>; |
| 326 |
regulator-system-load = <10000>; |
| 327 |
regulator-allow-set-load; |
| 328 |
regulator-boot-on; |
| 329 |
}; |
| 330 |
|
| 331 |
pm8994_l15: l15 { |
| 332 |
regulator-min-microvolt = <1800000>; |
| 333 |
regulator-max-microvolt = <1800000>; |
| 334 |
}; |
| 335 |
|
| 336 |
pm8994_l16: l16 { |
| 337 |
regulator-min-microvolt = <2700000>; |
| 338 |
regulator-max-microvolt = <2700000>; |
| 339 |
}; |
| 340 |
|
| 341 |
pm8994_l17: l17 { |
| 342 |
regulator-min-microvolt = <2200000>; |
| 343 |
regulator-max-microvolt = <2200000>; |
| 344 |
regulator-boot-on; |
| 345 |
}; |
| 346 |
|
| 347 |
pm8994_l18: l18 { |
| 348 |
regulator-min-microvolt = <2850000>; |
| 349 |
regulator-max-microvolt = <2850000>; |
| 350 |
regulator-always-on; |
| 351 |
regulator-boot-on; |
| 352 |
}; |
| 353 |
|
| 354 |
pm8994_l19: l19 { |
| 355 |
regulator-min-microvolt = <2850000>; |
| 356 |
regulator-max-microvolt = <2850000>; |
| 357 |
regulator-boot-on; |
| 358 |
}; |
| 359 |
|
| 360 |
pm8994_l20: l20 { |
| 361 |
regulator-min-microvolt = <2950000>; |
| 362 |
regulator-max-microvolt = <2950000>; |
| 363 |
regulator-system-load = <570000>; |
| 364 |
regulator-allow-set-load; |
| 365 |
}; |
| 366 |
|
| 367 |
pm8994_l21: l21 { |
| 368 |
regulator-min-microvolt = <2950000>; |
| 369 |
regulator-max-microvolt = <2950000>; |
| 370 |
regulator-system-load = <800000>; |
| 371 |
regulator-allow-set-load; |
| 372 |
}; |
| 373 |
|
| 374 |
pm8994_l22: l22 { |
| 375 |
regulator-min-microvolt = <3000000>; |
| 376 |
regulator-max-microvolt = <3000000>; |
| 377 |
regulator-boot-on; |
| 378 |
}; |
| 379 |
|
| 380 |
pm8994_l23: l23 { |
| 381 |
regulator-min-microvolt = <2800000>; |
| 382 |
regulator-max-microvolt = <2800000>; |
| 383 |
regulator-always-on; |
| 384 |
regulator-boot-on; |
| 385 |
}; |
| 386 |
|
| 387 |
pm8994_l24: l24 { |
| 388 |
regulator-min-microvolt = <3075000>; |
| 389 |
regulator-max-microvolt = <3150000>; |
| 390 |
}; |
| 391 |
|
| 392 |
pm8994_l25: l25 { |
| 393 |
regulator-min-microvolt = <1000000>; |
| 394 |
regulator-max-microvolt = <1000000>; |
| 395 |
regulator-boot-on; |
| 396 |
}; |
| 397 |
|
| 398 |
pm8994_l26: l26 { |
| 399 |
regulator-min-microvolt = <987500>; |
| 400 |
regulator-max-microvolt = <987500>; |
| 401 |
}; |
| 402 |
|
| 403 |
pm8994_l27: l27 { |
| 404 |
regulator-min-microvolt = <1200000>; |
| 405 |
regulator-max-microvolt = <1200000>; |
| 406 |
regulator-boot-on; |
| 407 |
}; |
| 408 |
|
| 409 |
pm8994_l28: l28 { |
| 410 |
regulator-min-microvolt = <1000000>; |
| 411 |
regulator-max-microvolt = <1000000>; |
| 412 |
regulator-system-load = <10000>; |
| 413 |
regulator-allow-set-load; |
| 414 |
}; |
| 415 |
|
| 416 |
pm8994_l29: l29 { |
| 417 |
regulator-min-microvolt = <2700000>; |
| 418 |
regulator-max-microvolt = <2700000>; |
| 419 |
regulator-boot-on; |
| 420 |
}; |
| 421 |
|
| 422 |
pm8994_l30: l30 { |
| 423 |
regulator-min-microvolt = <1800000>; |
| 424 |
regulator-max-microvolt = <1800000>; |
| 425 |
regulator-boot-on; |
| 426 |
}; |
| 427 |
|
| 428 |
pm8994_l31: l31 { |
| 429 |
regulator-min-microvolt = <1200000>; |
| 430 |
regulator-max-microvolt = <1200000>; |
| 431 |
regulator-system-load = <10000>; |
| 432 |
regulator-allow-set-load; |
| 433 |
}; |
| 434 |
|
| 435 |
pm8994_l32: l32 { |
| 436 |
regulator-min-microvolt = <1800000>; |
| 437 |
regulator-max-microvolt = <1800000>; |
| 438 |
}; |
| 439 |
|
| 440 |
pm8994_lvs1: lvs1 { |
| 441 |
regulator-boot-on; |
| 442 |
}; |
| 443 |
pm8994_lvs2: lvs2 { |
| 444 |
regulator-boot-on; |
| 445 |
}; |
| 446 |
}; |
| 447 |
}; |
| 448 |
|
| 449 |
&sdhc1 { |
| 450 |
/* |
| 451 |
* There is an issue with the eMMC causing permanent |
| 452 |
* damage to the card if a quirk isn't addressed. |
| 453 |
* Until it's fixed, disable the MMC so as not to brick |
| 454 |
* devices. |
| 455 |
*/ |
| 456 |
status = "disabled"; |
| 457 |
|
| 458 |
/* |
| 459 |
* Downstream pushes 2.95V to the sdhci device, |
| 460 |
* but upstream driver REALLY wants to make vmmc 1.8v |
| 461 |
* cause of the hs400-1_8v mode. MMC works fine without |
| 462 |
* that regulator, so let's not use it for now. |
| 463 |
* vqmmc is also disabled cause driver stll complains. |
| 464 |
* |
| 465 |
* vmmc-supply = <&pm8994_l20>; |
| 466 |
* vqmmc-supply = <&pm8994_s4>; |
| 467 |
*/ |
| 468 |
}; |
| 469 |
|
| 470 |
&sdhc2 { |
| 471 |
status = "okay"; |
| 472 |
|
| 473 |
cd-gpios = <&tlmm 100 GPIO_ACTIVE_HIGH>; |
| 474 |
vmmc-supply = <&pm8994_l21>; |
| 475 |
vqmmc-supply = <&pm8994_l13>; |
| 476 |
}; |
| 477 |
|
| 478 |
&tlmm { |
| 479 |
ts_int_active: ts-int-active-state { |
| 480 |
pins = "gpio42"; |
| 481 |
function = "gpio"; |
| 482 |
drive-strength = <2>; |
| 483 |
bias-disable; |
| 484 |
}; |
| 485 |
|
| 486 |
ts_reset_active: ts-reset-active-state { |
| 487 |
pins = "gpio109"; |
| 488 |
function = "gpio"; |
| 489 |
drive-strength = <2>; |
| 490 |
bias-disable; |
| 491 |
output-low; |
| 492 |
}; |
| 493 |
}; |