Debian Codegraph @

scripts/dtc/include-prefixes/arm64/qcom/msm8992-lg-h815.dts

raw
1 // SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
2 /*
3 * MSM8992 LG G4 (h815) device tree.
4 *
5 * Copyright (c) 2024, Alexander Reimelt <[email protected]>
6 */
7
8 /dts-v1/;
9
10 #include "msm8992.dtsi"
11 #include "pm8994.dtsi"
12 #include "pmi8994.dtsi"
13 #include <dt-bindings/leds/common.h>
14
15 /* different mapping */
16 /delete-node/ &cont_splash_mem;
17
18 /* disabled downstream */
19 /delete-node/ &dfps_data_mem;
20
21 / {
22 model = "LG G4 (H815)";
23 compatible = "lg,h815", "qcom,msm8992";
24 chassis-type = "handset";
25
26 qcom,msm-id = <0xfb 0x0>;
27 qcom,pmic-id = <0x10009 0x1000a 0x0 0x0>;
28 qcom,board-id = <0xb64 0x0>;
29
30 /* psci is broken */
31 /delete-node/ psci;
32
33 reserved-memory {
34 #address-cells = <2>;
35 #size-cells = <2>;
36 ranges;
37
38 spin-table@6000000 {
39 reg = <0x0 0x06000000 0x0 0x00001000>;
40 no-map;
41 };
42
43 ramoops@ff00000 {
44 compatible = "ramoops";
45 reg = <0x0 0x0ff00000 0x0 0x00100000>;
46 console-size = <0x20000>;
47 pmsg-size = <0x20000>;
48 record-size = <0x10000>;
49 ecc-size = <0x10>;
50 };
51
52 cont_splash_mem: fb@3400000 {
53 reg = <0x0 0x03400000 0x0 0x00c00000>;
54 no-map;
55 };
56
57 crash_fb_mem: crash-fb@4000000 {
58 reg = <0x0 0x04000000 0x0 0x00c00000>;
59 no-map;
60 };
61 };
62
63 gpio-hall-sensor {
64 compatible = "gpio-keys";
65
66 pinctrl-0 = <&hall_sensor_default>;
67 pinctrl-names = "default";
68
69 label = "Hall Effect Sensor";
70
71 event-hall-sensor {
72 gpios = <&tlmm 75 GPIO_ACTIVE_LOW>;
73 label = "hall effect sensor";
74 linux,input-type = <EV_SW>;
75 linux,code = <SW_LID>;
76 linux,can-disable;
77 wakeup-source;
78 };
79 };
80
81 gpio-keys {
82 compatible = "gpio-keys";
83
84 key-vol-up {
85 label = "volume up";
86 gpios = <&pm8994_gpios 3 GPIO_ACTIVE_LOW>;
87 linux,code = <KEY_VOLUMEUP>;
88 wakeup-source;
89 debounce-interval = <15>;
90 };
91 };
92 };
93
94 &cpu0 {
95 enable-method = "spin-table";
96 cpu-release-addr = /bits/ 64 <0>;
97 };
98
99 &cpu1 {
100 enable-method = "spin-table";
101 cpu-release-addr = /bits/ 64 <0>;
102 };
103
104 &cpu2 {
105 enable-method = "spin-table";
106 cpu-release-addr = /bits/ 64 <0>;
107 };
108
109 &cpu3 {
110 enable-method = "spin-table";
111 cpu-release-addr = /bits/ 64 <0>;
112 };
113
114 &cpu4 {
115 enable-method = "spin-table";
116 cpu-release-addr = /bits/ 64 <0>;
117 };
118
119 &cpu5 {
120 enable-method = "spin-table";
121 cpu-release-addr = /bits/ 64 <0>;
122 };
123
124 &pm8994_resin {
125 linux,code = <KEY_VOLUMEDOWN>;
126 status = "okay";
127 };
128
129 &rpm_requests {
130 regulators-0 {
131 compatible = "qcom,rpm-pm8994-regulators";
132
133 vdd_s3-supply = <&vph_pwr>;
134 vdd_s4-supply = <&vph_pwr>;
135 vdd_s5-supply = <&vph_pwr>;
136 vdd_s7-supply = <&vph_pwr>;
137 vdd_l1-supply = <&pmi8994_s1>;
138 vdd_l2_26_28-supply = <&pm8994_s3>;
139 vdd_l3_11-supply = <&pm8994_s3>;
140 vdd_l4_27_31-supply = <&pm8994_s3>;
141 vdd_l5_7-supply = <&pm8994_s5>;
142 vdd_l6_12_32-supply = <&pm8994_s5>;
143 vdd_l8_16_30-supply = <&vph_pwr>;
144 vdd_l9_10_18_22-supply = <&pmi8994_bby>;
145 vdd_l13_19_23_24-supply = <&pmi8994_bby>;
146 vdd_l14_15-supply = <&pm8994_s5>;
147 vdd_l17_29-supply = <&pmi8994_bby>;
148 vdd_l20_21-supply = <&pmi8994_bby>;
149 vdd_l25-supply = <&pm8994_s5>;
150 vdd_lvs1_2-supply = <&pm8994_s4>;
151
152 pm8994_s3: s3 {
153 regulator-min-microvolt = <1300000>;
154 regulator-max-microvolt = <1300000>;
155 };
156
157 /* sdhc1 vqmmc and bcm */
158 pm8994_s4: s4 {
159 regulator-min-microvolt = <1800000>;
160 regulator-max-microvolt = <1800000>;
161 regulator-system-load = <325000>;
162 regulator-allow-set-load;
163 };
164
165 pm8994_s5: s5 {
166 regulator-min-microvolt = <2150000>;
167 regulator-max-microvolt = <2150000>;
168 };
169
170 /* sdhc2 vqmmc */
171 pm8994_l13: l13 {
172 regulator-min-microvolt = <1800000>;
173 regulator-max-microvolt = <2950000>;
174 regulator-system-load = <22000>;
175 regulator-allow-set-load;
176 };
177
178 /* sdhc1 vmmc */
179 pm8994_l20: l20 {
180 regulator-min-microvolt = <2950000>;
181 regulator-max-microvolt = <2950000>;
182 regulator-system-load = <570000>;
183 regulator-allow-set-load;
184 };
185
186 /* sdhc2 vmmc */
187 pm8994_l21: l21 {
188 regulator-min-microvolt = <2950000>;
189 regulator-max-microvolt = <2950000>;
190 regulator-system-load = <800000>;
191 regulator-allow-set-load;
192 };
193 };
194
195 regulators-1 {
196 compatible = "qcom,rpm-pmi8994-regulators";
197
198 vdd_s1-supply = <&vph_pwr>;
199 vdd_bst_byp-supply = <&vph_pwr>;
200
201 pmi8994_s1: s1 {
202 regulator-min-microvolt = <1025000>;
203 regulator-max-microvolt = <1025000>;
204 };
205
206 /* S2 & S3 - VDD_GFX */
207
208 pmi8994_bby: boost-bypass {
209 regulator-min-microvolt = <3150000>;
210 regulator-max-microvolt = <3600000>;
211 };
212 };
213 };
214
215 &sdhc1 {
216 mmc-hs400-1_8v;
217 vmmc-supply = <&pm8994_l20>;
218 vqmmc-supply = <&pm8994_s4>;
219 non-removable;
220 status = "okay";
221 };
222
223 &sdhc2 {
224 vmmc-supply = <&pm8994_l21>;
225 vqmmc-supply = <&pm8994_l13>;
226 cd-gpios = <&pm8994_gpios 8 GPIO_ACTIVE_LOW>;
227 status = "okay";
228 };
229
230 &tlmm {
231 hall_sensor_default: hall-sensor-default-state {
232 pins = "gpio75";
233 function = "gpio";
234 drive-strength = <2>;
235 bias-pull-up;
236 };
237 };