| 1 |
// SPDX-License-Identifier: BSD-3-Clause |
| 2 |
/* |
| 3 |
* Copyright (c) 2022, Eugene Lepshy <[email protected]> |
| 4 |
* Copyright (c) 2022, Gianluca Boiano <[email protected]> |
| 5 |
*/ |
| 6 |
/dts-v1/; |
| 7 |
|
| 8 |
#include "msm8953.dtsi" |
| 9 |
#include "pm8953.dtsi" |
| 10 |
#include "pmi8950.dtsi" |
| 11 |
#include <dt-bindings/leds/common.h> |
| 12 |
|
| 13 |
/delete-node/ &adsp_fw_mem; |
| 14 |
/delete-node/ &cont_splash_mem; |
| 15 |
/delete-node/ &qseecom_mem; |
| 16 |
/delete-node/ &wcnss_fw_mem; |
| 17 |
|
| 18 |
/ { |
| 19 |
model = "Xiaomi Redmi 5 Plus"; |
| 20 |
compatible = "xiaomi,vince", "qcom,msm8953"; |
| 21 |
chassis-type = "handset"; |
| 22 |
qcom,msm-id = <293 0>; |
| 23 |
qcom,board-id = <0x1000b 0x08>; |
| 24 |
|
| 25 |
gpio-keys { |
| 26 |
compatible = "gpio-keys"; |
| 27 |
|
| 28 |
pinctrl-names = "default"; |
| 29 |
pinctrl-0 = <&gpio_key_default>; |
| 30 |
|
| 31 |
key-volume-up { |
| 32 |
label = "volume_up"; |
| 33 |
linux,code = <KEY_VOLUMEUP>; |
| 34 |
gpios = <&tlmm 85 GPIO_ACTIVE_LOW>; |
| 35 |
}; |
| 36 |
}; |
| 37 |
|
| 38 |
reserved-memory { |
| 39 |
qseecom_mem: qseecom@84a00000 { |
| 40 |
reg = <0x0 0x84a00000 0x0 0x1900000>; |
| 41 |
no-map; |
| 42 |
}; |
| 43 |
|
| 44 |
cont_splash_mem: cont-splash@90001000 { |
| 45 |
reg = <0x0 0x90001000 0x0 (1080 * 2160 * 3)>; |
| 46 |
no-map; |
| 47 |
}; |
| 48 |
|
| 49 |
adsp_fw_mem: adsp@8d600000 { |
| 50 |
reg = <0x0 0x8d600000 0x0 0x1200000>; |
| 51 |
no-map; |
| 52 |
}; |
| 53 |
|
| 54 |
wcnss_fw_mem: wcnss@8e800000 { |
| 55 |
reg = <0x0 0x8e800000 0x0 0x700000>; |
| 56 |
no-map; |
| 57 |
}; |
| 58 |
|
| 59 |
ramoops@9ff00000 { |
| 60 |
compatible = "ramoops"; |
| 61 |
reg = <0x0 0x9ff00000 0x0 0x100000>; |
| 62 |
record-size = <0x1000>; |
| 63 |
console-size = <0x80000>; |
| 64 |
ftrace-size = <0x1000>; |
| 65 |
pmsg-size = <0x8000>; |
| 66 |
}; |
| 67 |
}; |
| 68 |
|
| 69 |
/* |
| 70 |
* We bitbang on &i2c_4 because BLSP is protected by TZ as sensors are |
| 71 |
* normally proxied via ADSP firmware. GPIOs aren't protected. |
| 72 |
*/ |
| 73 |
i2c-sensors { |
| 74 |
compatible = "i2c-gpio"; |
| 75 |
sda-gpios = <&tlmm 14 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 76 |
scl-gpios = <&tlmm 15 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 77 |
i2c-gpio,delay-us = <2>; /* ~100 kHz */ |
| 78 |
#address-cells = <1>; |
| 79 |
#size-cells = <0>; |
| 80 |
|
| 81 |
imu@6a { |
| 82 |
compatible = "st,lsm6dsl"; |
| 83 |
reg = <0x6a>; |
| 84 |
vdd-supply = <&pm8953_l10>; |
| 85 |
vddio-supply = <&pm8953_l6>; |
| 86 |
mount-matrix = "1", "0", "0", |
| 87 |
"0", "-1", "0", |
| 88 |
"0", "0", "1"; |
| 89 |
}; |
| 90 |
}; |
| 91 |
|
| 92 |
vph_pwr: vph-pwr-regulator { |
| 93 |
compatible = "regulator-fixed"; |
| 94 |
regulator-name = "vph_pwr"; |
| 95 |
regulator-always-on; |
| 96 |
regulator-boot-on; |
| 97 |
}; |
| 98 |
}; |
| 99 |
|
| 100 |
&hsusb_phy { |
| 101 |
vdd-supply = <&pm8953_l3>; |
| 102 |
vdda-pll-supply = <&pm8953_l7>; |
| 103 |
vdda-phy-dpdm-supply = <&pm8953_l13>; |
| 104 |
|
| 105 |
status = "okay"; |
| 106 |
}; |
| 107 |
|
| 108 |
&i2c_2 { |
| 109 |
status = "okay"; |
| 110 |
|
| 111 |
led-controller@45 { |
| 112 |
compatible = "awinic,aw2013"; |
| 113 |
reg = <0x45>; |
| 114 |
|
| 115 |
vcc-supply = <&pm8953_l10>; |
| 116 |
vio-supply = <&pm8953_l5>; |
| 117 |
|
| 118 |
#address-cells = <1>; |
| 119 |
#size-cells = <0>; |
| 120 |
|
| 121 |
led@0 { |
| 122 |
reg = <0>; |
| 123 |
led-max-microamp = <5000>; |
| 124 |
function = LED_FUNCTION_INDICATOR; |
| 125 |
color = <LED_COLOR_ID_WHITE>; |
| 126 |
}; |
| 127 |
}; |
| 128 |
}; |
| 129 |
|
| 130 |
&i2c_3 { |
| 131 |
status = "okay"; |
| 132 |
|
| 133 |
touchscreen@20 { |
| 134 |
reg = <0x20>; |
| 135 |
compatible = "syna,rmi4-i2c"; |
| 136 |
interrupts-extended = <&tlmm 65 IRQ_TYPE_EDGE_FALLING>; |
| 137 |
|
| 138 |
#address-cells = <1>; |
| 139 |
#size-cells = <0>; |
| 140 |
|
| 141 |
vdd-supply = <&pm8953_l10>; |
| 142 |
vio-supply = <&pm8953_l6>; |
| 143 |
|
| 144 |
pinctrl-names = "init", "suspend"; |
| 145 |
pinctrl-0 = <&ts_reset_active &ts_int_active>; |
| 146 |
pinctrl-1 = <&ts_reset_suspend &ts_int_suspend>; |
| 147 |
syna,reset-delay-ms = <200>; |
| 148 |
syna,startup-delay-ms = <500>; |
| 149 |
|
| 150 |
rmi4-f01@1 { |
| 151 |
reg = <0x01>; |
| 152 |
syna,nosleep-mode = <1>; |
| 153 |
}; |
| 154 |
|
| 155 |
rmi4-f12@12 { |
| 156 |
reg = <0x12>; |
| 157 |
syna,rezero-wait-ms = <20>; |
| 158 |
syna,sensor-type = <1>; |
| 159 |
touchscreen-x-mm = <68>; |
| 160 |
touchscreen-y-mm = <122>; |
| 161 |
}; |
| 162 |
}; |
| 163 |
}; |
| 164 |
|
| 165 |
&pm8953_resin { |
| 166 |
linux,code = <KEY_VOLUMEDOWN>; |
| 167 |
status = "okay"; |
| 168 |
}; |
| 169 |
|
| 170 |
&pmi8950_wled { |
| 171 |
qcom,current-limit-microamp = <20000>; |
| 172 |
qcom,ovp-millivolt = <29600>; |
| 173 |
qcom,num-strings = <2>; |
| 174 |
qcom,external-pfet; |
| 175 |
qcom,cabc; |
| 176 |
|
| 177 |
status = "okay"; |
| 178 |
}; |
| 179 |
|
| 180 |
&rpm_requests { |
| 181 |
regulators { |
| 182 |
compatible = "qcom,rpm-pm8953-regulators"; |
| 183 |
vdd_s1-supply = <&vph_pwr>; |
| 184 |
vdd_s2-supply = <&vph_pwr>; |
| 185 |
vdd_s3-supply = <&vph_pwr>; |
| 186 |
vdd_s4-supply = <&vph_pwr>; |
| 187 |
vdd_s5-supply = <&vph_pwr>; |
| 188 |
vdd_s6-supply = <&vph_pwr>; |
| 189 |
vdd_s7-supply = <&vph_pwr>; |
| 190 |
vdd_l1-supply = <&pm8953_s3>; |
| 191 |
vdd_l2_l3-supply = <&pm8953_s3>; |
| 192 |
vdd_l4_l5_l6_l7_l16_l19-supply = <&pm8953_s4>; |
| 193 |
vdd_l8_l11_l12_l13_l14_l15-supply = <&vph_pwr>; |
| 194 |
vdd_l9_l10_l17_l18_l22-supply = <&vph_pwr>; |
| 195 |
|
| 196 |
pm8953_s1: s1 { |
| 197 |
regulator-min-microvolt = <870000>; |
| 198 |
regulator-max-microvolt = <1156000>; |
| 199 |
}; |
| 200 |
|
| 201 |
pm8953_s3: s3 { |
| 202 |
regulator-min-microvolt = <984000>; |
| 203 |
regulator-max-microvolt = <1224000>; |
| 204 |
}; |
| 205 |
|
| 206 |
pm8953_s4: s4 { |
| 207 |
regulator-min-microvolt = <1900000>; |
| 208 |
regulator-max-microvolt = <2050000>; |
| 209 |
}; |
| 210 |
|
| 211 |
pm8953_l1: l1 { |
| 212 |
regulator-min-microvolt = <1000000>; |
| 213 |
regulator-max-microvolt = <1100000>; |
| 214 |
}; |
| 215 |
|
| 216 |
pm8953_l2: l2 { |
| 217 |
regulator-min-microvolt = <1200000>; |
| 218 |
regulator-max-microvolt = <1225000>; |
| 219 |
}; |
| 220 |
|
| 221 |
pm8953_l3: l3 { |
| 222 |
regulator-min-microvolt = <925000>; |
| 223 |
regulator-max-microvolt = <925000>; |
| 224 |
}; |
| 225 |
|
| 226 |
pm8953_l5: l5 { |
| 227 |
regulator-min-microvolt = <1800000>; |
| 228 |
regulator-max-microvolt = <1800000>; |
| 229 |
}; |
| 230 |
|
| 231 |
pm8953_l6: l6 { |
| 232 |
regulator-min-microvolt = <1800000>; |
| 233 |
regulator-max-microvolt = <1800000>; |
| 234 |
}; |
| 235 |
|
| 236 |
pm8953_l7: l7 { |
| 237 |
regulator-min-microvolt = <1800000>; |
| 238 |
regulator-max-microvolt = <1900000>; |
| 239 |
}; |
| 240 |
|
| 241 |
pm8953_l8: l8 { |
| 242 |
regulator-min-microvolt = <2900000>; |
| 243 |
regulator-max-microvolt = <2900000>; |
| 244 |
}; |
| 245 |
|
| 246 |
pm8953_l9: l9 { |
| 247 |
regulator-min-microvolt = <3000000>; |
| 248 |
regulator-max-microvolt = <3300000>; |
| 249 |
}; |
| 250 |
|
| 251 |
pm8953_l10: l10 { |
| 252 |
regulator-min-microvolt = <2850000>; |
| 253 |
regulator-max-microvolt = <2850000>; |
| 254 |
}; |
| 255 |
|
| 256 |
pm8953_l11: l11 { |
| 257 |
regulator-min-microvolt = <2950000>; |
| 258 |
regulator-max-microvolt = <2950000>; |
| 259 |
}; |
| 260 |
|
| 261 |
pm8953_l12: l12 { |
| 262 |
regulator-min-microvolt = <1800000>; |
| 263 |
regulator-max-microvolt = <2950000>; |
| 264 |
}; |
| 265 |
|
| 266 |
pm8953_l13: l13 { |
| 267 |
regulator-min-microvolt = <3125000>; |
| 268 |
regulator-max-microvolt = <3125000>; |
| 269 |
}; |
| 270 |
|
| 271 |
pm8953_l16: l16 { |
| 272 |
regulator-min-microvolt = <1800000>; |
| 273 |
regulator-max-microvolt = <1800000>; |
| 274 |
}; |
| 275 |
|
| 276 |
pm8953_l17: l17 { |
| 277 |
regulator-min-microvolt = <2750000>; |
| 278 |
regulator-max-microvolt = <2850000>; |
| 279 |
}; |
| 280 |
|
| 281 |
pm8953_l19: l19 { |
| 282 |
regulator-min-microvolt = <1200000>; |
| 283 |
regulator-max-microvolt = <1380000>; |
| 284 |
}; |
| 285 |
|
| 286 |
pm8953_l22: l22 { |
| 287 |
regulator-min-microvolt = <2800000>; |
| 288 |
regulator-max-microvolt = <2800000>; |
| 289 |
}; |
| 290 |
|
| 291 |
pm8953_l23: l23 { |
| 292 |
regulator-min-microvolt = <1200000>; |
| 293 |
regulator-max-microvolt = <1225000>; |
| 294 |
}; |
| 295 |
}; |
| 296 |
}; |
| 297 |
|
| 298 |
&sdhc_1 { |
| 299 |
vmmc-supply = <&pm8953_l8>; |
| 300 |
vqmmc-supply = <&pm8953_l5>; |
| 301 |
|
| 302 |
status = "okay"; |
| 303 |
}; |
| 304 |
|
| 305 |
&sdhc_2 { |
| 306 |
vmmc-supply = <&pm8953_l11>; |
| 307 |
vqmmc-supply = <&pm8953_l12>; |
| 308 |
|
| 309 |
pinctrl-names = "default", "sleep"; |
| 310 |
pinctrl-0 = <&sdc2_clk_on &sdc2_cmd_on &sdc2_data_on &sdc2_cd_on>; |
| 311 |
pinctrl-1 = <&sdc2_clk_off &sdc2_cmd_off &sdc2_data_off &sdc2_cd_off>; |
| 312 |
|
| 313 |
status = "okay"; |
| 314 |
}; |
| 315 |
|
| 316 |
&tlmm { |
| 317 |
gpio-reserved-ranges = <0 4>, <16 4>, <135 4>; |
| 318 |
|
| 319 |
ts_reset_active: ts-reset-active-state { |
| 320 |
pins = "gpio64"; |
| 321 |
function = "gpio"; |
| 322 |
drive-strength = <8>; |
| 323 |
bias-pull-up; |
| 324 |
}; |
| 325 |
|
| 326 |
ts_reset_suspend: ts-reset-suspend-state { |
| 327 |
pins = "gpio64"; |
| 328 |
function = "gpio"; |
| 329 |
drive-strength = <2>; |
| 330 |
bias-pull-up; |
| 331 |
}; |
| 332 |
|
| 333 |
ts_int_active: ts-int-active-state { |
| 334 |
pins = "gpio65"; |
| 335 |
function = "gpio"; |
| 336 |
drive-strength = <8>; |
| 337 |
bias-pull-up; |
| 338 |
}; |
| 339 |
|
| 340 |
ts_int_suspend: ts-int-suspend-state { |
| 341 |
pins = "gpio65"; |
| 342 |
function = "gpio"; |
| 343 |
drive-strength = <2>; |
| 344 |
bias-pull-down; |
| 345 |
}; |
| 346 |
}; |
| 347 |
|
| 348 |
&uart_0 { |
| 349 |
pinctrl-names = "default"; |
| 350 |
pinctrl-0 = <&uart_console_active>; |
| 351 |
|
| 352 |
status = "okay"; |
| 353 |
}; |
| 354 |
|
| 355 |
&usb3 { |
| 356 |
status = "okay"; |
| 357 |
}; |
| 358 |
|
| 359 |
&usb3_dwc3 { |
| 360 |
/delete-property/ usb-role-switch; |
| 361 |
dr_mode = "peripheral"; |
| 362 |
}; |