| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
|
| 3 |
#include "msm8916-pm8916.dtsi" |
| 4 |
#include "msm8916-modem-qdsp6.dtsi" |
| 5 |
|
| 6 |
#include <dt-bindings/gpio/gpio.h> |
| 7 |
#include <dt-bindings/input/input.h> |
| 8 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 9 |
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| 10 |
|
| 11 |
/ { |
| 12 |
aliases { |
| 13 |
mmc0 = &sdhc_1; /* eMMC */ |
| 14 |
mmc1 = &sdhc_2; /* SD card */ |
| 15 |
serial0 = &blsp_uart2; |
| 16 |
}; |
| 17 |
|
| 18 |
chosen { |
| 19 |
stdout-path = "serial0"; |
| 20 |
}; |
| 21 |
|
| 22 |
reserved-memory { |
| 23 |
/* Additional memory used by Samsung firmware modifications */ |
| 24 |
tz-apps@85a00000 { |
| 25 |
reg = <0x0 0x85a00000 0x0 0x600000>; |
| 26 |
no-map; |
| 27 |
}; |
| 28 |
}; |
| 29 |
|
| 30 |
battery: battery { |
| 31 |
compatible = "simple-battery"; |
| 32 |
precharge-current-microamp = <450000>; |
| 33 |
precharge-upper-limit-microvolt = <3500000>; |
| 34 |
}; |
| 35 |
|
| 36 |
clk_pwm_backlight: backlight { |
| 37 |
compatible = "pwm-backlight"; |
| 38 |
pwms = <&clk_pwm 0 100000>; |
| 39 |
|
| 40 |
enable-gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>; |
| 41 |
|
| 42 |
brightness-levels = <0 255>; |
| 43 |
num-interpolated-steps = <255>; |
| 44 |
default-brightness-level = <128>; |
| 45 |
|
| 46 |
pinctrl-0 = <&backlight_en_default>; |
| 47 |
pinctrl-names = "default"; |
| 48 |
}; |
| 49 |
|
| 50 |
clk_pwm: pwm { |
| 51 |
compatible = "clk-pwm"; |
| 52 |
#pwm-cells = <2>; |
| 53 |
|
| 54 |
clocks = <&gcc GCC_GP2_CLK>; |
| 55 |
|
| 56 |
pinctrl-0 = <&backlight_pwm_default>; |
| 57 |
pinctrl-names = "default"; |
| 58 |
}; |
| 59 |
|
| 60 |
gpio-keys { |
| 61 |
compatible = "gpio-keys"; |
| 62 |
|
| 63 |
pinctrl-0 = <&gpio_keys_default>; |
| 64 |
pinctrl-names = "default"; |
| 65 |
|
| 66 |
label = "GPIO Buttons"; |
| 67 |
|
| 68 |
button-volume-up { |
| 69 |
label = "Volume Up"; |
| 70 |
gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; |
| 71 |
linux,code = <KEY_VOLUMEUP>; |
| 72 |
}; |
| 73 |
|
| 74 |
button-home { |
| 75 |
label = "Home"; |
| 76 |
gpios = <&tlmm 109 GPIO_ACTIVE_LOW>; |
| 77 |
linux,code = <KEY_HOMEPAGE>; |
| 78 |
}; |
| 79 |
}; |
| 80 |
|
| 81 |
haptic { |
| 82 |
compatible = "regulator-haptic"; |
| 83 |
haptic-supply = <®_motor_vdd>; |
| 84 |
min-microvolt = <3300000>; |
| 85 |
max-microvolt = <3300000>; |
| 86 |
}; |
| 87 |
|
| 88 |
i2c_nfc: i2c-nfc { |
| 89 |
compatible = "i2c-gpio"; |
| 90 |
sda-gpios = <&tlmm 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 91 |
scl-gpios = <&tlmm 1 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 92 |
|
| 93 |
pinctrl-0 = <&nfc_i2c_default>; |
| 94 |
pinctrl-names = "default"; |
| 95 |
|
| 96 |
#address-cells = <1>; |
| 97 |
#size-cells = <0>; |
| 98 |
|
| 99 |
s3fwrn5_nfc: nfc@27 { |
| 100 |
compatible = "samsung,s3fwrn5-i2c"; |
| 101 |
reg = <0x27>; |
| 102 |
|
| 103 |
interrupts-extended = <&tlmm 21 IRQ_TYPE_EDGE_RISING>; |
| 104 |
|
| 105 |
en-gpios = <&tlmm 20 GPIO_ACTIVE_HIGH>; |
| 106 |
wake-gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>; |
| 107 |
|
| 108 |
clocks = <&rpmcc RPM_SMD_BB_CLK2_PIN>; |
| 109 |
|
| 110 |
pinctrl-0 = <&nfc_default>, <&nfc_clk_req>; |
| 111 |
pinctrl-names = "default"; |
| 112 |
|
| 113 |
status = "disabled"; |
| 114 |
}; |
| 115 |
}; |
| 116 |
|
| 117 |
reg_motor_vdd: regulator-motor-vdd { |
| 118 |
compatible = "regulator-fixed"; |
| 119 |
regulator-name = "motor_vdd"; |
| 120 |
regulator-min-microvolt = <3300000>; |
| 121 |
regulator-max-microvolt = <3300000>; |
| 122 |
|
| 123 |
gpio = <&tlmm 72 GPIO_ACTIVE_HIGH>; |
| 124 |
enable-active-high; |
| 125 |
|
| 126 |
pinctrl-0 = <&motor_en_default>; |
| 127 |
pinctrl-names = "default"; |
| 128 |
}; |
| 129 |
|
| 130 |
reg_vdd_tsp_a: regulator-vdd-tsp-a { |
| 131 |
compatible = "regulator-fixed"; |
| 132 |
regulator-name = "vdd_tsp_a"; |
| 133 |
regulator-min-microvolt = <3000000>; |
| 134 |
regulator-max-microvolt = <3000000>; |
| 135 |
|
| 136 |
gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>; |
| 137 |
enable-active-high; |
| 138 |
|
| 139 |
pinctrl-0 = <&tsp_en_default>; |
| 140 |
pinctrl-names = "default"; |
| 141 |
}; |
| 142 |
}; |
| 143 |
|
| 144 |
&blsp_i2c1 { |
| 145 |
status = "okay"; |
| 146 |
|
| 147 |
muic: extcon@25 { |
| 148 |
compatible = "siliconmitus,sm5502-muic"; |
| 149 |
reg = <0x25>; |
| 150 |
interrupts-extended = <&tlmm 12 IRQ_TYPE_EDGE_FALLING>; |
| 151 |
pinctrl-0 = <&muic_int_default>; |
| 152 |
pinctrl-names = "default"; |
| 153 |
|
| 154 |
usb_con: connector { |
| 155 |
compatible = "usb-b-connector"; |
| 156 |
label = "micro-USB"; |
| 157 |
type = "micro"; |
| 158 |
}; |
| 159 |
}; |
| 160 |
}; |
| 161 |
|
| 162 |
&blsp_i2c2 { |
| 163 |
/* Available sensors vary depending on model variant */ |
| 164 |
status = "okay"; |
| 165 |
|
| 166 |
bosch_accel: accelerometer@10 { |
| 167 |
compatible = "bosch,bmc150_accel"; |
| 168 |
reg = <0x10>; |
| 169 |
interrupts-extended = <&tlmm 115 IRQ_TYPE_EDGE_RISING>; |
| 170 |
|
| 171 |
vdd-supply = <&pm8916_l5>; |
| 172 |
vddio-supply = <&pm8916_l5>; |
| 173 |
|
| 174 |
pinctrl-0 = <&accel_int_default>; |
| 175 |
pinctrl-names = "default"; |
| 176 |
|
| 177 |
mount-matrix = "0", "-1", "0", |
| 178 |
"-1", "0", "0", |
| 179 |
"0", "0", "1"; |
| 180 |
|
| 181 |
status = "disabled"; |
| 182 |
}; |
| 183 |
|
| 184 |
bosch_magn: magnetometer@12 { |
| 185 |
compatible = "bosch,bmc150_magn"; |
| 186 |
reg = <0x12>; |
| 187 |
|
| 188 |
vdd-supply = <&pm8916_l5>; |
| 189 |
vddio-supply = <&pm8916_l5>; |
| 190 |
|
| 191 |
mount-matrix = "0", "-1", "0", |
| 192 |
"-1", "0", "0", |
| 193 |
"0", "0", "1"; |
| 194 |
|
| 195 |
status = "disabled"; |
| 196 |
}; |
| 197 |
|
| 198 |
st_accel: accelerometer@1d { |
| 199 |
compatible = "st,lsm303c-accel"; |
| 200 |
reg = <0x1d>; |
| 201 |
interrupts-extended = <&tlmm 115 IRQ_TYPE_LEVEL_HIGH>; |
| 202 |
|
| 203 |
vdd-supply = <&pm8916_l17>; |
| 204 |
vddio-supply = <&pm8916_l5>; |
| 205 |
|
| 206 |
pinctrl-0 = <&accel_int_default>; |
| 207 |
pinctrl-names = "default"; |
| 208 |
|
| 209 |
st,drdy-int-pin = <1>; |
| 210 |
mount-matrix = "0", "-1", "0", |
| 211 |
"1", "0", "0", |
| 212 |
"0", "0", "-1"; |
| 213 |
|
| 214 |
status = "disabled"; |
| 215 |
}; |
| 216 |
|
| 217 |
st_magn: magnetometer@1e { |
| 218 |
compatible = "st,lsm303c-magn"; |
| 219 |
reg = <0x1e>; |
| 220 |
|
| 221 |
vdd-supply = <&pm8916_l17>; |
| 222 |
vddio-supply = <&pm8916_l5>; |
| 223 |
|
| 224 |
mount-matrix = "0", "-1", "0", |
| 225 |
"1", "0", "0", |
| 226 |
"0", "0", "-1"; |
| 227 |
|
| 228 |
status = "disabled"; |
| 229 |
}; |
| 230 |
}; |
| 231 |
|
| 232 |
&blsp_i2c4 { |
| 233 |
status = "okay"; |
| 234 |
|
| 235 |
fuel-gauge@35 { |
| 236 |
compatible = "richtek,rt5033-battery"; |
| 237 |
reg = <0x35>; |
| 238 |
|
| 239 |
interrupts-extended = <&tlmm 121 IRQ_TYPE_EDGE_FALLING>; |
| 240 |
|
| 241 |
pinctrl-0 = <&fg_alert_default>; |
| 242 |
pinctrl-names = "default"; |
| 243 |
|
| 244 |
power-supplies = <&charger>; |
| 245 |
}; |
| 246 |
}; |
| 247 |
|
| 248 |
&blsp_i2c5 { |
| 249 |
status = "okay"; |
| 250 |
|
| 251 |
touchscreen: touchscreen@20 { |
| 252 |
compatible = "zinitix,bt541"; |
| 253 |
reg = <0x20>; |
| 254 |
|
| 255 |
interrupts-extended = <&tlmm 13 IRQ_TYPE_EDGE_FALLING>; |
| 256 |
|
| 257 |
touchscreen-size-x = <540>; |
| 258 |
touchscreen-size-y = <960>; |
| 259 |
|
| 260 |
vcca-supply = <®_vdd_tsp_a>; |
| 261 |
vdd-supply = <&pm8916_l6>; |
| 262 |
|
| 263 |
pinctrl-0 = <&tsp_int_default>; |
| 264 |
pinctrl-names = "default"; |
| 265 |
|
| 266 |
linux,keycodes = <KEY_APPSELECT KEY_BACK>; |
| 267 |
}; |
| 268 |
}; |
| 269 |
|
| 270 |
&blsp_i2c6 { |
| 271 |
status = "okay"; |
| 272 |
|
| 273 |
pmic@34 { |
| 274 |
compatible = "richtek,rt5033"; |
| 275 |
reg = <0x34>; |
| 276 |
|
| 277 |
interrupts-extended = <&tlmm 62 IRQ_TYPE_EDGE_FALLING>; |
| 278 |
|
| 279 |
pinctrl-0 = <&pmic_int_default>; |
| 280 |
pinctrl-names = "default"; |
| 281 |
|
| 282 |
regulators { |
| 283 |
rt5033_reg_safe_ldo: SAFE_LDO { |
| 284 |
regulator-min-microvolt = <4900000>; |
| 285 |
regulator-max-microvolt = <4900000>; |
| 286 |
regulator-always-on; |
| 287 |
}; |
| 288 |
|
| 289 |
/* |
| 290 |
* Needed for camera, but not used yet. |
| 291 |
* Define empty nodes to allow disabling the unused |
| 292 |
* regulators. |
| 293 |
*/ |
| 294 |
LDO {}; |
| 295 |
BUCK {}; |
| 296 |
}; |
| 297 |
|
| 298 |
charger: charger { |
| 299 |
compatible = "richtek,rt5033-charger"; |
| 300 |
monitored-battery = <&battery>; |
| 301 |
richtek,usb-connector = <&usb_con>; |
| 302 |
}; |
| 303 |
}; |
| 304 |
}; |
| 305 |
|
| 306 |
&blsp_uart2 { |
| 307 |
pinctrl-0 = <&blsp_uart2_console_default>; |
| 308 |
pinctrl-1 = <&blsp_uart2_console_sleep>; |
| 309 |
pinctrl-names = "default", "sleep"; |
| 310 |
status = "okay"; |
| 311 |
}; |
| 312 |
|
| 313 |
&mpss_mem { |
| 314 |
reg = <0x0 0x86800000 0x0 0x5000000>; |
| 315 |
}; |
| 316 |
|
| 317 |
&pm8916_resin { |
| 318 |
linux,code = <KEY_VOLUMEDOWN>; |
| 319 |
status = "okay"; |
| 320 |
}; |
| 321 |
|
| 322 |
&pm8916_rpm_regulators { |
| 323 |
pm8916_l17: l17 { |
| 324 |
regulator-min-microvolt = <2850000>; |
| 325 |
regulator-max-microvolt = <2850000>; |
| 326 |
}; |
| 327 |
}; |
| 328 |
|
| 329 |
&sdhc_1 { |
| 330 |
status = "okay"; |
| 331 |
}; |
| 332 |
|
| 333 |
&sdhc_2 { |
| 334 |
pinctrl-0 = <&sdc2_default &sdc2_cd_default>; |
| 335 |
pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>; |
| 336 |
pinctrl-names = "default", "sleep"; |
| 337 |
|
| 338 |
cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; |
| 339 |
|
| 340 |
status = "okay"; |
| 341 |
}; |
| 342 |
|
| 343 |
&sound { |
| 344 |
model = "msm8916-1mic"; |
| 345 |
audio-routing = |
| 346 |
"AMIC1", "MIC BIAS External1", |
| 347 |
"AMIC2", "MIC BIAS Internal2", |
| 348 |
"AMIC3", "MIC BIAS External1"; |
| 349 |
}; |
| 350 |
|
| 351 |
&usb { |
| 352 |
extcon = <&muic>, <&muic>; |
| 353 |
status = "okay"; |
| 354 |
}; |
| 355 |
|
| 356 |
&usb_hs_phy { |
| 357 |
extcon = <&muic>; |
| 358 |
}; |
| 359 |
|
| 360 |
&venus { |
| 361 |
status = "okay"; |
| 362 |
}; |
| 363 |
|
| 364 |
&venus_mem { |
| 365 |
status = "okay"; |
| 366 |
}; |
| 367 |
|
| 368 |
&wcnss { |
| 369 |
status = "okay"; |
| 370 |
}; |
| 371 |
|
| 372 |
&wcnss_iris { |
| 373 |
compatible = "qcom,wcn3620"; |
| 374 |
}; |
| 375 |
|
| 376 |
&wcnss_mem { |
| 377 |
status = "okay"; |
| 378 |
}; |
| 379 |
|
| 380 |
&tlmm { |
| 381 |
accel_int_default: accel-int-default-state { |
| 382 |
pins = "gpio115"; |
| 383 |
function = "gpio"; |
| 384 |
drive-strength = <2>; |
| 385 |
bias-disable; |
| 386 |
}; |
| 387 |
|
| 388 |
backlight_en_default: backlight-en-default-state { |
| 389 |
pins = "gpio98"; |
| 390 |
function = "gpio"; |
| 391 |
drive-strength = <2>; |
| 392 |
bias-disable; |
| 393 |
}; |
| 394 |
|
| 395 |
backlight_pwm_default: backlight-pwm-default-state { |
| 396 |
pins = "gpio50"; |
| 397 |
function = "gcc_gp2_clk_a"; |
| 398 |
}; |
| 399 |
|
| 400 |
fg_alert_default: fg-alert-default-state { |
| 401 |
pins = "gpio121"; |
| 402 |
function = "gpio"; |
| 403 |
drive-strength = <2>; |
| 404 |
bias-disable; |
| 405 |
}; |
| 406 |
|
| 407 |
gpio_keys_default: gpio-keys-default-state { |
| 408 |
pins = "gpio107", "gpio109"; |
| 409 |
function = "gpio"; |
| 410 |
drive-strength = <2>; |
| 411 |
bias-pull-up; |
| 412 |
}; |
| 413 |
|
| 414 |
motor_en_default: motor-en-default-state { |
| 415 |
pins = "gpio72"; |
| 416 |
function = "gpio"; |
| 417 |
drive-strength = <2>; |
| 418 |
bias-disable; |
| 419 |
}; |
| 420 |
|
| 421 |
muic_int_default: muic-int-default-state { |
| 422 |
pins = "gpio12"; |
| 423 |
function = "gpio"; |
| 424 |
drive-strength = <2>; |
| 425 |
bias-disable; |
| 426 |
}; |
| 427 |
|
| 428 |
nfc_default: nfc-default-state { |
| 429 |
irq-pins { |
| 430 |
pins = "gpio21"; |
| 431 |
function = "gpio"; |
| 432 |
drive-strength = <2>; |
| 433 |
bias-pull-down; |
| 434 |
}; |
| 435 |
|
| 436 |
nfc-pins { |
| 437 |
pins = "gpio20", "gpio49"; |
| 438 |
function = "gpio"; |
| 439 |
drive-strength = <2>; |
| 440 |
bias-disable; |
| 441 |
}; |
| 442 |
}; |
| 443 |
|
| 444 |
nfc_i2c_default: nfc-i2c-default-state { |
| 445 |
pins = "gpio0", "gpio1"; |
| 446 |
function = "gpio"; |
| 447 |
drive-strength = <2>; |
| 448 |
bias-disable; |
| 449 |
}; |
| 450 |
|
| 451 |
pmic_int_default: pmic-int-default-state { |
| 452 |
pins = "gpio62"; |
| 453 |
function = "gpio"; |
| 454 |
drive-strength = <2>; |
| 455 |
bias-disable; |
| 456 |
}; |
| 457 |
|
| 458 |
sdc2_cd_default: sdc2-cd-default-state { |
| 459 |
pins = "gpio38"; |
| 460 |
function = "gpio"; |
| 461 |
drive-strength = <2>; |
| 462 |
bias-disable; |
| 463 |
}; |
| 464 |
|
| 465 |
tsp_en_default: tsp-en-default-state { |
| 466 |
pins = "gpio73"; |
| 467 |
function = "gpio"; |
| 468 |
drive-strength = <2>; |
| 469 |
bias-disable; |
| 470 |
}; |
| 471 |
|
| 472 |
tsp_int_default: tsp-int-default-state { |
| 473 |
pins = "gpio13"; |
| 474 |
function = "gpio"; |
| 475 |
drive-strength = <2>; |
| 476 |
bias-disable; |
| 477 |
}; |
| 478 |
}; |
| 479 |
|
| 480 |
&pm8916_gpios { |
| 481 |
nfc_clk_req: nfc-clk-req-state { |
| 482 |
pins = "gpio2"; |
| 483 |
function = "func1"; |
| 484 |
power-source = <PM8916_GPIO_L2>; |
| 485 |
bias-disable; |
| 486 |
input-enable; |
| 487 |
}; |
| 488 |
}; |