| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
|
| 3 |
#include "msm8916-pm8916.dtsi" |
| 4 |
#include "msm8916-modem-qdsp6.dtsi" |
| 5 |
|
| 6 |
#include <dt-bindings/gpio/gpio.h> |
| 7 |
#include <dt-bindings/input/input.h> |
| 8 |
#include <dt-bindings/interrupt-controller/irq.h> |
| 9 |
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| 10 |
#include <dt-bindings/sound/apq8016-lpass.h> |
| 11 |
|
| 12 |
/ { |
| 13 |
aliases { |
| 14 |
mmc0 = &sdhc_1; /* eMMC */ |
| 15 |
mmc1 = &sdhc_2; /* SD card */ |
| 16 |
serial0 = &blsp_uart2; |
| 17 |
}; |
| 18 |
|
| 19 |
chosen { |
| 20 |
stdout-path = "serial0"; |
| 21 |
}; |
| 22 |
|
| 23 |
reserved-memory { |
| 24 |
/* Additional memory used by Samsung firmware modifications */ |
| 25 |
tz-apps@85500000 { |
| 26 |
reg = <0x0 0x85500000 0x0 0xb00000>; |
| 27 |
no-map; |
| 28 |
}; |
| 29 |
}; |
| 30 |
|
| 31 |
battery: battery { |
| 32 |
compatible = "simple-battery"; |
| 33 |
precharge-current-microamp = <450000>; |
| 34 |
precharge-upper-limit-microvolt = <3500000>; |
| 35 |
}; |
| 36 |
|
| 37 |
clk_pwm: pwm { |
| 38 |
compatible = "clk-pwm"; |
| 39 |
#pwm-cells = <2>; |
| 40 |
|
| 41 |
clocks = <&gcc GCC_GP2_CLK>; |
| 42 |
|
| 43 |
pinctrl-names = "default"; |
| 44 |
pinctrl-0 = <&motor_pwm_default>; |
| 45 |
status = "disabled"; |
| 46 |
}; |
| 47 |
|
| 48 |
gpio-keys { |
| 49 |
compatible = "gpio-keys"; |
| 50 |
|
| 51 |
pinctrl-names = "default"; |
| 52 |
pinctrl-0 = <&gpio_keys_default>; |
| 53 |
|
| 54 |
label = "GPIO Buttons"; |
| 55 |
|
| 56 |
button-volume-up { |
| 57 |
label = "Volume Up"; |
| 58 |
gpios = <&tlmm 107 GPIO_ACTIVE_LOW>; |
| 59 |
linux,code = <KEY_VOLUMEUP>; |
| 60 |
}; |
| 61 |
|
| 62 |
button-home { |
| 63 |
label = "Home"; |
| 64 |
gpios = <&tlmm 109 GPIO_ACTIVE_LOW>; |
| 65 |
linux,code = <KEY_HOMEPAGE>; |
| 66 |
}; |
| 67 |
}; |
| 68 |
|
| 69 |
gpio-hall-sensor { |
| 70 |
compatible = "gpio-keys"; |
| 71 |
|
| 72 |
pinctrl-names = "default"; |
| 73 |
pinctrl-0 = <&gpio_hall_sensor_default>; |
| 74 |
|
| 75 |
label = "GPIO Hall Effect Sensor"; |
| 76 |
|
| 77 |
event-hall-sensor { |
| 78 |
label = "Hall Effect Sensor"; |
| 79 |
gpios = <&tlmm 52 GPIO_ACTIVE_LOW>; |
| 80 |
linux,input-type = <EV_SW>; |
| 81 |
linux,code = <SW_LID>; |
| 82 |
linux,can-disable; |
| 83 |
}; |
| 84 |
}; |
| 85 |
|
| 86 |
/* |
| 87 |
* NOTE: A5 connects GPIO 76 to a reglator powering the motor |
| 88 |
* driver IC but A3 connects the same signal to an ENABLE pin of |
| 89 |
* the driver. |
| 90 |
*/ |
| 91 |
reg_motor_vdd: regulator-motor-vdd { |
| 92 |
compatible = "regulator-fixed"; |
| 93 |
regulator-name = "motor_vdd"; |
| 94 |
regulator-min-microvolt = <3000000>; |
| 95 |
regulator-max-microvolt = <3000000>; |
| 96 |
|
| 97 |
gpio = <&tlmm 76 GPIO_ACTIVE_HIGH>; |
| 98 |
enable-active-high; |
| 99 |
|
| 100 |
pinctrl-names = "default"; |
| 101 |
pinctrl-0 = <&motor_en_default>; |
| 102 |
}; |
| 103 |
|
| 104 |
reg_vdd_tsp_a: regulator-vdd-tsp-a { |
| 105 |
compatible = "regulator-fixed"; |
| 106 |
regulator-name = "vdd_tsp_a"; |
| 107 |
regulator-min-microvolt = <3300000>; |
| 108 |
regulator-max-microvolt = <3300000>; |
| 109 |
|
| 110 |
gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>; |
| 111 |
enable-active-high; |
| 112 |
|
| 113 |
pinctrl-names = "default"; |
| 114 |
pinctrl-0 = <&tsp_en_default>; |
| 115 |
}; |
| 116 |
|
| 117 |
i2c-muic { |
| 118 |
compatible = "i2c-gpio"; |
| 119 |
sda-gpios = <&tlmm 105 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 120 |
scl-gpios = <&tlmm 106 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 121 |
|
| 122 |
pinctrl-names = "default"; |
| 123 |
pinctrl-0 = <&muic_i2c_default>; |
| 124 |
|
| 125 |
#address-cells = <1>; |
| 126 |
#size-cells = <0>; |
| 127 |
|
| 128 |
muic: extcon@25 { |
| 129 |
compatible = "siliconmitus,sm5502-muic"; |
| 130 |
|
| 131 |
reg = <0x25>; |
| 132 |
interrupt-parent = <&tlmm>; |
| 133 |
interrupts = <12 IRQ_TYPE_EDGE_FALLING>; |
| 134 |
|
| 135 |
pinctrl-names = "default"; |
| 136 |
pinctrl-0 = <&muic_int_default>; |
| 137 |
|
| 138 |
usb_con: connector { |
| 139 |
compatible = "usb-b-connector"; |
| 140 |
label = "micro-USB"; |
| 141 |
type = "micro"; |
| 142 |
}; |
| 143 |
}; |
| 144 |
}; |
| 145 |
|
| 146 |
i2c-tkey { |
| 147 |
compatible = "i2c-gpio"; |
| 148 |
sda-gpios = <&tlmm 16 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 149 |
scl-gpios = <&tlmm 17 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 150 |
|
| 151 |
pinctrl-names = "default"; |
| 152 |
pinctrl-0 = <&tkey_i2c_default>; |
| 153 |
|
| 154 |
#address-cells = <1>; |
| 155 |
#size-cells = <0>; |
| 156 |
|
| 157 |
touchkey: touchkey@20 { |
| 158 |
/* Note: Actually an ABOV MCU that implements same interface */ |
| 159 |
compatible = "coreriver,tc360-touchkey"; |
| 160 |
reg = <0x20>; |
| 161 |
|
| 162 |
interrupt-parent = <&tlmm>; |
| 163 |
interrupts = <98 IRQ_TYPE_EDGE_FALLING>; |
| 164 |
|
| 165 |
/* vcc/vdd-supply are board-specific */ |
| 166 |
vddio-supply = <&pm8916_l6>; |
| 167 |
|
| 168 |
linux,keycodes = <KEY_APPSELECT KEY_BACK>; |
| 169 |
|
| 170 |
pinctrl-names = "default"; |
| 171 |
pinctrl-0 = <&tkey_default>; |
| 172 |
}; |
| 173 |
}; |
| 174 |
|
| 175 |
i2c-nfc { |
| 176 |
compatible = "i2c-gpio"; |
| 177 |
sda-gpios = <&tlmm 0 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 178 |
scl-gpios = <&tlmm 1 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>; |
| 179 |
|
| 180 |
pinctrl-names = "default"; |
| 181 |
pinctrl-0 = <&nfc_i2c_default>; |
| 182 |
|
| 183 |
#address-cells = <1>; |
| 184 |
#size-cells = <0>; |
| 185 |
|
| 186 |
nfc@27 { |
| 187 |
compatible = "samsung,s3fwrn5-i2c"; |
| 188 |
reg = <0x27>; |
| 189 |
|
| 190 |
interrupt-parent = <&tlmm>; |
| 191 |
interrupts = <21 IRQ_TYPE_EDGE_RISING>; |
| 192 |
|
| 193 |
en-gpios = <&tlmm 20 GPIO_ACTIVE_LOW>; |
| 194 |
wake-gpios = <&tlmm 49 GPIO_ACTIVE_HIGH>; |
| 195 |
|
| 196 |
clocks = <&rpmcc RPM_SMD_BB_CLK2_PIN>; |
| 197 |
|
| 198 |
pinctrl-names = "default"; |
| 199 |
pinctrl-0 = <&nfc_default &nfc_clk_req>; |
| 200 |
}; |
| 201 |
}; |
| 202 |
|
| 203 |
vibrator: vibrator { |
| 204 |
compatible = "pwm-vibrator"; |
| 205 |
|
| 206 |
pwms = <&clk_pwm 0 100000>; |
| 207 |
pwm-names = "enable"; |
| 208 |
|
| 209 |
vcc-supply = <®_motor_vdd>; |
| 210 |
status = "disabled"; |
| 211 |
}; |
| 212 |
}; |
| 213 |
|
| 214 |
&blsp_i2c1 { |
| 215 |
status = "okay"; |
| 216 |
|
| 217 |
speaker_codec: audio-codec@34 { |
| 218 |
compatible = "nxp,tfa9895"; |
| 219 |
reg = <0x34>; |
| 220 |
vddd-supply = <&pm8916_l5>; |
| 221 |
sound-name-prefix = "Speaker"; |
| 222 |
#sound-dai-cells = <0>; |
| 223 |
}; |
| 224 |
}; |
| 225 |
|
| 226 |
&blsp_i2c2 { |
| 227 |
status = "okay"; |
| 228 |
|
| 229 |
accelerometer: accelerometer@10 { |
| 230 |
compatible = "bosch,bmc150_accel"; |
| 231 |
reg = <0x10>; |
| 232 |
interrupt-parent = <&tlmm>; |
| 233 |
interrupts = <115 IRQ_TYPE_EDGE_RISING>; |
| 234 |
|
| 235 |
vdd-supply = <&pm8916_l17>; |
| 236 |
vddio-supply = <&pm8916_l5>; |
| 237 |
|
| 238 |
pinctrl-names = "default"; |
| 239 |
pinctrl-0 = <&accel_int_default>; |
| 240 |
}; |
| 241 |
|
| 242 |
magnetometer@12 { |
| 243 |
compatible = "bosch,bmc150_magn"; |
| 244 |
reg = <0x12>; |
| 245 |
|
| 246 |
vdd-supply = <&pm8916_l17>; |
| 247 |
vddio-supply = <&pm8916_l5>; |
| 248 |
}; |
| 249 |
}; |
| 250 |
|
| 251 |
&blsp_i2c4 { |
| 252 |
status = "okay"; |
| 253 |
|
| 254 |
fuel-gauge@35 { |
| 255 |
compatible = "richtek,rt5033-battery"; |
| 256 |
reg = <0x35>; |
| 257 |
interrupt-parent = <&tlmm>; |
| 258 |
interrupts = <121 IRQ_TYPE_EDGE_BOTH>; |
| 259 |
|
| 260 |
pinctrl-names = "default"; |
| 261 |
pinctrl-0 = <&fg_alert_default>; |
| 262 |
|
| 263 |
power-supplies = <&charger>; |
| 264 |
}; |
| 265 |
}; |
| 266 |
|
| 267 |
&blsp_i2c6 { |
| 268 |
status = "okay"; |
| 269 |
|
| 270 |
pmic@34 { |
| 271 |
compatible = "richtek,rt5033"; |
| 272 |
reg = <0x34>; |
| 273 |
|
| 274 |
interrupts-extended = <&tlmm 62 IRQ_TYPE_EDGE_FALLING>; |
| 275 |
|
| 276 |
pinctrl-0 = <&pmic_int_default>; |
| 277 |
pinctrl-names = "default"; |
| 278 |
|
| 279 |
regulators { |
| 280 |
rt5033_reg_safe_ldo: SAFE_LDO { |
| 281 |
regulator-min-microvolt = <4900000>; |
| 282 |
regulator-max-microvolt = <4900000>; |
| 283 |
regulator-always-on; |
| 284 |
}; |
| 285 |
|
| 286 |
/* |
| 287 |
* Needed for camera, but not used yet. |
| 288 |
* Define empty nodes to allow disabling the unused |
| 289 |
* regulators. |
| 290 |
*/ |
| 291 |
LDO {}; |
| 292 |
BUCK {}; |
| 293 |
}; |
| 294 |
|
| 295 |
charger: charger { |
| 296 |
compatible = "richtek,rt5033-charger"; |
| 297 |
monitored-battery = <&battery>; |
| 298 |
richtek,usb-connector = <&usb_con>; |
| 299 |
}; |
| 300 |
}; |
| 301 |
}; |
| 302 |
|
| 303 |
&blsp_uart2 { |
| 304 |
status = "okay"; |
| 305 |
pinctrl-0 = <&blsp_uart2_console_default>; |
| 306 |
pinctrl-1 = <&blsp_uart2_console_sleep>; |
| 307 |
pinctrl-names = "default", "sleep"; |
| 308 |
}; |
| 309 |
|
| 310 |
&gpu { |
| 311 |
status = "okay"; |
| 312 |
}; |
| 313 |
|
| 314 |
/* |
| 315 |
* For some reason the speaker amplifier is connected to the second SD line |
| 316 |
* (MI2S_2_D1) instead of the first (MI2S_2_D0). This must be configured in the |
| 317 |
* device tree, otherwise audio will seemingly play fine on the wrong SD line |
| 318 |
* but the speaker stays silent. |
| 319 |
* |
| 320 |
* When routing audio via QDSP6 (the default) the &lpass node is reserved and |
| 321 |
* the definitions from &q6afedai are used. When the modem is disabled audio can |
| 322 |
* be alternatively routed directly to the LPASS hardware with reduced latency. |
| 323 |
* The definitions for &lpass are here for completeness to simplify changing the |
| 324 |
* setup with minor changes to the DT (either manually or with DT overlays). |
| 325 |
*/ |
| 326 |
&lpass { |
| 327 |
dai-link@3 { |
| 328 |
reg = <MI2S_QUATERNARY>; |
| 329 |
qcom,playback-sd-lines = <1>; |
| 330 |
}; |
| 331 |
}; |
| 332 |
|
| 333 |
&mdss { |
| 334 |
status = "okay"; |
| 335 |
}; |
| 336 |
|
| 337 |
&mdss_dsi0 { |
| 338 |
pinctrl-names = "default", "sleep"; |
| 339 |
pinctrl-0 = <&mdss_default>; |
| 340 |
pinctrl-1 = <&mdss_sleep>; |
| 341 |
}; |
| 342 |
|
| 343 |
&mpss_mem { |
| 344 |
reg = <0x0 0x86800000 0x0 0x5400000>; |
| 345 |
}; |
| 346 |
|
| 347 |
&pm8916_resin { |
| 348 |
status = "okay"; |
| 349 |
linux,code = <KEY_VOLUMEDOWN>; |
| 350 |
}; |
| 351 |
|
| 352 |
&pm8916_rpm_regulators { |
| 353 |
pm8916_l17: l17 { |
| 354 |
regulator-min-microvolt = <2850000>; |
| 355 |
regulator-max-microvolt = <2850000>; |
| 356 |
}; |
| 357 |
}; |
| 358 |
|
| 359 |
&q6afedai { |
| 360 |
dai@22 { |
| 361 |
reg = <QUATERNARY_MI2S_RX>; |
| 362 |
qcom,sd-lines = <1>; |
| 363 |
}; |
| 364 |
}; |
| 365 |
|
| 366 |
&sdhc_1 { |
| 367 |
status = "okay"; |
| 368 |
}; |
| 369 |
|
| 370 |
&sdhc_2 { |
| 371 |
status = "okay"; |
| 372 |
|
| 373 |
pinctrl-names = "default", "sleep"; |
| 374 |
pinctrl-0 = <&sdc2_default &sdc2_cd_default>; |
| 375 |
pinctrl-1 = <&sdc2_sleep &sdc2_cd_default>; |
| 376 |
|
| 377 |
cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>; |
| 378 |
}; |
| 379 |
|
| 380 |
&sound { |
| 381 |
model = "samsung-a2015"; |
| 382 |
audio-routing = |
| 383 |
"AMIC1", "MIC BIAS External1", |
| 384 |
"AMIC2", "MIC BIAS Internal2", |
| 385 |
"AMIC3", "MIC BIAS External1"; |
| 386 |
|
| 387 |
pinctrl-0 = <&cdc_pdm_default &sec_mi2s_default>; |
| 388 |
pinctrl-1 = <&cdc_pdm_sleep &sec_mi2s_sleep>; |
| 389 |
pinctrl-names = "default", "sleep"; |
| 390 |
|
| 391 |
sound_link_backend2: backend2-dai-link { |
| 392 |
link-name = "Quaternary MI2S"; |
| 393 |
|
| 394 |
cpu { |
| 395 |
sound-dai = <&q6afedai QUATERNARY_MI2S_RX>; |
| 396 |
}; |
| 397 |
platform { |
| 398 |
sound-dai = <&q6routing>; |
| 399 |
}; |
| 400 |
codec { |
| 401 |
sound-dai = <&speaker_codec>; |
| 402 |
}; |
| 403 |
}; |
| 404 |
}; |
| 405 |
|
| 406 |
&usb { |
| 407 |
status = "okay"; |
| 408 |
extcon = <&muic>, <&muic>; |
| 409 |
}; |
| 410 |
|
| 411 |
&usb_hs_phy { |
| 412 |
extcon = <&muic>; |
| 413 |
}; |
| 414 |
|
| 415 |
&venus { |
| 416 |
status = "okay"; |
| 417 |
}; |
| 418 |
|
| 419 |
&venus_mem { |
| 420 |
status = "okay"; |
| 421 |
}; |
| 422 |
|
| 423 |
&tlmm { |
| 424 |
accel_int_default: accel-int-default-state { |
| 425 |
pins = "gpio115"; |
| 426 |
function = "gpio"; |
| 427 |
|
| 428 |
drive-strength = <2>; |
| 429 |
bias-disable; |
| 430 |
}; |
| 431 |
|
| 432 |
fg_alert_default: fg-alert-default-state { |
| 433 |
pins = "gpio121"; |
| 434 |
function = "gpio"; |
| 435 |
|
| 436 |
drive-strength = <2>; |
| 437 |
bias-disable; |
| 438 |
}; |
| 439 |
|
| 440 |
gpio_keys_default: gpio-keys-default-state { |
| 441 |
pins = "gpio107", "gpio109"; |
| 442 |
function = "gpio"; |
| 443 |
|
| 444 |
drive-strength = <2>; |
| 445 |
bias-pull-up; |
| 446 |
}; |
| 447 |
|
| 448 |
gpio_hall_sensor_default: gpio-hall-sensor-default-state { |
| 449 |
pins = "gpio52"; |
| 450 |
function = "gpio"; |
| 451 |
|
| 452 |
drive-strength = <2>; |
| 453 |
bias-disable; |
| 454 |
}; |
| 455 |
|
| 456 |
mdss_default: mdss-default-state { |
| 457 |
pins = "gpio25"; |
| 458 |
function = "gpio"; |
| 459 |
|
| 460 |
drive-strength = <8>; |
| 461 |
bias-disable; |
| 462 |
}; |
| 463 |
mdss_sleep: mdss-sleep-state { |
| 464 |
pins = "gpio25"; |
| 465 |
function = "gpio"; |
| 466 |
|
| 467 |
drive-strength = <2>; |
| 468 |
bias-pull-down; |
| 469 |
}; |
| 470 |
|
| 471 |
motor_en_default: motor-en-default-state { |
| 472 |
pins = "gpio76"; |
| 473 |
function = "gpio"; |
| 474 |
|
| 475 |
drive-strength = <2>; |
| 476 |
bias-disable; |
| 477 |
}; |
| 478 |
|
| 479 |
motor_pwm_default: motor-pwm-default-state { |
| 480 |
pins = "gpio50"; |
| 481 |
function = "gcc_gp2_clk_a"; |
| 482 |
}; |
| 483 |
|
| 484 |
muic_i2c_default: muic-i2c-default-state { |
| 485 |
pins = "gpio105", "gpio106"; |
| 486 |
function = "gpio"; |
| 487 |
|
| 488 |
drive-strength = <2>; |
| 489 |
bias-disable; |
| 490 |
}; |
| 491 |
|
| 492 |
muic_int_default: muic-int-default-state { |
| 493 |
pins = "gpio12"; |
| 494 |
function = "gpio"; |
| 495 |
|
| 496 |
drive-strength = <2>; |
| 497 |
bias-disable; |
| 498 |
}; |
| 499 |
|
| 500 |
nfc_default: nfc-default-state { |
| 501 |
nfc-pins { |
| 502 |
pins = "gpio20", "gpio49"; |
| 503 |
function = "gpio"; |
| 504 |
|
| 505 |
drive-strength = <2>; |
| 506 |
bias-disable; |
| 507 |
}; |
| 508 |
|
| 509 |
irq-pins { |
| 510 |
pins = "gpio21"; |
| 511 |
function = "gpio"; |
| 512 |
|
| 513 |
drive-strength = <2>; |
| 514 |
bias-pull-down; |
| 515 |
}; |
| 516 |
}; |
| 517 |
|
| 518 |
nfc_i2c_default: nfc-i2c-default-state { |
| 519 |
pins = "gpio0", "gpio1"; |
| 520 |
function = "gpio"; |
| 521 |
|
| 522 |
drive-strength = <2>; |
| 523 |
bias-disable; |
| 524 |
}; |
| 525 |
|
| 526 |
pmic_int_default: pmic-int-default-state { |
| 527 |
pins = "gpio62"; |
| 528 |
function = "gpio"; |
| 529 |
drive-strength = <2>; |
| 530 |
bias-disable; |
| 531 |
}; |
| 532 |
|
| 533 |
sdc2_cd_default: sdc2-cd-default-state { |
| 534 |
pins = "gpio38"; |
| 535 |
function = "gpio"; |
| 536 |
drive-strength = <2>; |
| 537 |
bias-disable; |
| 538 |
}; |
| 539 |
|
| 540 |
tkey_default: tkey-default-state { |
| 541 |
pins = "gpio98"; |
| 542 |
function = "gpio"; |
| 543 |
|
| 544 |
drive-strength = <2>; |
| 545 |
bias-disable; |
| 546 |
}; |
| 547 |
|
| 548 |
tkey_i2c_default: tkey-i2c-default-state { |
| 549 |
pins = "gpio16", "gpio17"; |
| 550 |
function = "gpio"; |
| 551 |
|
| 552 |
drive-strength = <2>; |
| 553 |
bias-disable; |
| 554 |
}; |
| 555 |
|
| 556 |
tsp_en_default: tsp-en-default-state { |
| 557 |
pins = "gpio73"; |
| 558 |
function = "gpio"; |
| 559 |
|
| 560 |
drive-strength = <2>; |
| 561 |
bias-disable; |
| 562 |
}; |
| 563 |
|
| 564 |
ts_int_default: ts-int-default-state { |
| 565 |
pins = "gpio13"; |
| 566 |
function = "gpio"; |
| 567 |
|
| 568 |
drive-strength = <2>; |
| 569 |
bias-disable; |
| 570 |
}; |
| 571 |
}; |
| 572 |
|
| 573 |
&pm8916_gpios { |
| 574 |
nfc_clk_req: nfc-clk-req-state { |
| 575 |
pins = "gpio2"; |
| 576 |
function = "func1"; |
| 577 |
|
| 578 |
input-enable; |
| 579 |
bias-disable; |
| 580 |
power-source = <PM8916_GPIO_L2>; |
| 581 |
}; |
| 582 |
}; |