Debian Codegraph @

scripts/dtc/include-prefixes/arm64/qcom/lemans-ride-common.dtsi

raw
1 // SPDX-License-Identifier: BSD-3-Clause
2 /*
3 * Copyright (c) 2023, Linaro Limited
4 */
5
6 #include <dt-bindings/gpio/gpio.h>
7 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
8
9 / {
10 aliases {
11 i2c11 = &i2c11;
12 i2c18 = &i2c18;
13 serial0 = &uart10;
14 serial1 = &uart12;
15 serial2 = &uart17;
16 spi16 = &spi16;
17 ufshc1 = &ufs_mem_hc;
18 };
19
20 chosen {
21 stdout-path = "serial0:115200n8";
22 };
23
24 vreg_12p0: vreg-12p0-regulator {
25 compatible = "regulator-fixed";
26 regulator-name = "VREG_12P0";
27
28 regulator-always-on;
29 regulator-boot-on;
30 regulator-min-microvolt = <12000000>;
31 regulator-max-microvolt = <12000000>;
32 };
33
34 vreg_5p0: vreg-5p0-regulator {
35 compatible = "regulator-fixed";
36 regulator-name = "VREG_5P0";
37
38 regulator-always-on;
39 regulator-boot-on;
40 regulator-min-microvolt = <5000000>;
41 regulator-max-microvolt = <5000000>;
42
43 vin-supply = <&vreg_12p0>;
44 };
45
46 vreg_1p8: vreg-1p8-regulator {
47 compatible = "regulator-fixed";
48 regulator-name = "VREG_1P8";
49
50 regulator-always-on;
51 regulator-boot-on;
52 regulator-min-microvolt = <1800000>;
53 regulator-max-microvolt = <1800000>;
54
55 vin-supply = <&vreg_5p0>;
56 };
57
58 vreg_1p0: vreg-1p0-regulator {
59 compatible = "regulator-fixed";
60 regulator-name = "VREG_1P0";
61
62 regulator-always-on;
63 regulator-boot-on;
64 regulator-min-microvolt = <1000000>;
65 regulator-max-microvolt = <1000000>;
66
67 vin-supply = <&vreg_1p8>;
68 };
69
70 vreg_3p0: vreg-3p0-regulator {
71 compatible = "regulator-fixed";
72 regulator-name = "VREG_3P0";
73
74 regulator-always-on;
75 regulator-boot-on;
76 regulator-min-microvolt = <3000000>;
77 regulator-max-microvolt = <3000000>;
78
79 vin-supply = <&vreg_12p0>;
80 };
81
82 vreg_conn_1p8: vreg_conn_1p8 {
83 compatible = "regulator-fixed";
84 regulator-name = "vreg_conn_1p8";
85 startup-delay-us = <4000>;
86 enable-active-high;
87 gpio = <&pmm8654au_1_gpios 4 GPIO_ACTIVE_HIGH>;
88 };
89
90 vreg_conn_pa: vreg_conn_pa {
91 compatible = "regulator-fixed";
92 regulator-name = "vreg_conn_pa";
93 startup-delay-us = <4000>;
94 enable-active-high;
95 gpio = <&pmm8654au_1_gpios 6 GPIO_ACTIVE_HIGH>;
96 };
97
98 wcn6855-pmu {
99 compatible = "qcom,wcn6855-pmu";
100
101 pinctrl-names = "default";
102 pinctrl-0 = <&bt_en_state>, <&wlan_en_state>;
103
104 vddio-supply = <&vreg_conn_pa>;
105 vddaon-supply = <&vreg_l2c>;
106 vddpmu-supply = <&vreg_conn_1p8>;
107 vddrfa0p95-supply = <&vreg_l2c>;
108 vddrfa1p3-supply = <&vreg_l6e>;
109 vddrfa1p9-supply = <&vreg_s5a>;
110 vddpcie1p3-supply = <&vreg_l6e>;
111 vddpcie1p9-supply = <&vreg_s5a>;
112
113 bt-enable-gpios = <&pmm8654au_1_gpios 8 GPIO_ACTIVE_HIGH>;
114 wlan-enable-gpios = <&pmm8654au_1_gpios 7 GPIO_ACTIVE_HIGH>;
115
116 regulators {
117 vreg_pmu_rfa_cmn: ldo0 {
118 regulator-name = "vreg_pmu_rfa_cmn";
119 };
120
121 vreg_pmu_aon_0p59: ldo1 {
122 regulator-name = "vreg_pmu_aon_0p59";
123 };
124
125 vreg_pmu_wlcx_0p8: ldo2 {
126 regulator-name = "vreg_pmu_wlcx_0p8";
127 };
128
129 vreg_pmu_wlmx_0p85: ldo3 {
130 regulator-name = "vreg_pmu_wlmx_0p85";
131 };
132
133 vreg_pmu_btcmx_0p85: ldo4 {
134 regulator-name = "vreg_pmu_btcmx_0p85";
135 };
136
137 vreg_pmu_rfa_0p8: ldo5 {
138 regulator-name = "vreg_pmu_rfa_0p8";
139 };
140
141 vreg_pmu_rfa_1p2: ldo6 {
142 regulator-name = "vreg_pmu_rfa_1p2";
143 };
144
145 vreg_pmu_rfa_1p7: ldo7 {
146 regulator-name = "vreg_pmu_rfa_1p7";
147 };
148
149 vreg_pmu_pcie_0p9: ldo8 {
150 regulator-name = "vreg_pmu_pcie_0p9";
151 };
152
153 vreg_pmu_pcie_1p8: ldo9 {
154 regulator-name = "vreg_pmu_pcie_1p8";
155 };
156 };
157 };
158
159 dp0-connector {
160 compatible = "dp-connector";
161 label = "eDP0";
162 type = "full-size";
163
164 port {
165 dp0_connector_in: endpoint {
166 remote-endpoint = <&mdss0_dp0_out>;
167 };
168 };
169 };
170
171 dp1-connector {
172 compatible = "dp-connector";
173 label = "eDP1";
174 type = "full-size";
175
176 port {
177 dp1_connector_in: endpoint {
178 remote-endpoint = <&mdss0_dp1_out>;
179 };
180 };
181 };
182
183 dp-dsi0-connector {
184 compatible = "dp-connector";
185 label = "DSI0";
186 type = "full-size";
187
188 port {
189 dp_dsi0_connector_in: endpoint {
190 remote-endpoint = <&dsi2dp_bridge0_out>;
191 };
192 };
193 };
194
195 dp-dsi1-connector {
196 compatible = "dp-connector";
197 label = "DSI1";
198 type = "full-size";
199
200 port {
201 dp_dsi1_connector_in: endpoint {
202 remote-endpoint = <&dsi2dp_bridge1_out>;
203 };
204 };
205 };
206 };
207
208 &apps_rsc {
209 regulators-0 {
210 compatible = "qcom,pmm8654au-rpmh-regulators";
211 qcom,pmic-id = "a";
212
213 vreg_s4a: smps4 {
214 regulator-name = "vreg_s4a";
215 regulator-min-microvolt = <1800000>;
216 regulator-max-microvolt = <1816000>;
217 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
218 };
219
220 vreg_s5a: smps5 {
221 regulator-name = "vreg_s5a";
222 regulator-min-microvolt = <1850000>;
223 regulator-max-microvolt = <1996000>;
224 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
225 };
226
227 vreg_s9a: smps9 {
228 regulator-name = "vreg_s9a";
229 regulator-min-microvolt = <535000>;
230 regulator-max-microvolt = <1120000>;
231 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
232 };
233
234 vreg_l4a: ldo4 {
235 regulator-name = "vreg_l4a";
236 regulator-min-microvolt = <788000>;
237 regulator-max-microvolt = <1050000>;
238 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
239 regulator-allow-set-load;
240 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
241 RPMH_REGULATOR_MODE_HPM>;
242 };
243
244 vreg_l5a: ldo5 {
245 regulator-name = "vreg_l5a";
246 regulator-min-microvolt = <870000>;
247 regulator-max-microvolt = <950000>;
248 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
249 regulator-allow-set-load;
250 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
251 RPMH_REGULATOR_MODE_HPM>;
252 };
253
254 vreg_l6a: ldo6 {
255 regulator-name = "vreg_l6a";
256 regulator-min-microvolt = <870000>;
257 regulator-max-microvolt = <970000>;
258 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
259 regulator-allow-set-load;
260 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
261 RPMH_REGULATOR_MODE_HPM>;
262 };
263
264 vreg_l7a: ldo7 {
265 regulator-name = "vreg_l7a";
266 regulator-min-microvolt = <720000>;
267 regulator-max-microvolt = <950000>;
268 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
269 regulator-allow-set-load;
270 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
271 RPMH_REGULATOR_MODE_HPM>;
272 };
273
274 vreg_l8a: ldo8 {
275 regulator-name = "vreg_l8a";
276 regulator-min-microvolt = <2504000>;
277 regulator-max-microvolt = <3300000>;
278 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
279 regulator-allow-set-load;
280 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
281 RPMH_REGULATOR_MODE_HPM>;
282 };
283
284 vreg_l9a: ldo9 {
285 regulator-name = "vreg_l9a";
286 regulator-min-microvolt = <2970000>;
287 regulator-max-microvolt = <3544000>;
288 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
289 regulator-allow-set-load;
290 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
291 RPMH_REGULATOR_MODE_HPM>;
292 };
293 };
294
295 regulators-1 {
296 compatible = "qcom,pmm8654au-rpmh-regulators";
297 qcom,pmic-id = "c";
298
299 vreg_l1c: ldo1 {
300 regulator-name = "vreg_l1c";
301 regulator-min-microvolt = <1140000>;
302 regulator-max-microvolt = <1260000>;
303 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
304 regulator-allow-set-load;
305 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
306 RPMH_REGULATOR_MODE_HPM>;
307 };
308
309 vreg_l2c: ldo2 {
310 regulator-name = "vreg_l2c";
311 regulator-min-microvolt = <900000>;
312 regulator-max-microvolt = <1100000>;
313 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
314 regulator-allow-set-load;
315 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
316 RPMH_REGULATOR_MODE_HPM>;
317 };
318
319 vreg_l3c: ldo3 {
320 regulator-name = "vreg_l3c";
321 regulator-min-microvolt = <1100000>;
322 regulator-max-microvolt = <1300000>;
323 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
324 regulator-allow-set-load;
325 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
326 RPMH_REGULATOR_MODE_HPM>;
327 };
328
329 vreg_l4c: ldo4 {
330 regulator-name = "vreg_l4c";
331 regulator-min-microvolt = <1200000>;
332 regulator-max-microvolt = <1200000>;
333 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
334 /*
335 * FIXME: This should have regulator-allow-set-load but
336 * we're getting an over-current fault from the PMIC
337 * when switching to LPM.
338 */
339 };
340
341 vreg_l5c: ldo5 {
342 regulator-name = "vreg_l5c";
343 regulator-min-microvolt = <1100000>;
344 regulator-max-microvolt = <1300000>;
345 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
346 regulator-allow-set-load;
347 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
348 RPMH_REGULATOR_MODE_HPM>;
349 };
350
351 vreg_l6c: ldo6 {
352 regulator-name = "vreg_l6c";
353 regulator-min-microvolt = <1620000>;
354 regulator-max-microvolt = <1980000>;
355 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
356 regulator-allow-set-load;
357 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
358 RPMH_REGULATOR_MODE_HPM>;
359 };
360
361 vreg_l7c: ldo7 {
362 regulator-name = "vreg_l7c";
363 regulator-min-microvolt = <1620000>;
364 regulator-max-microvolt = <2000000>;
365 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
366 regulator-allow-set-load;
367 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
368 RPMH_REGULATOR_MODE_HPM>;
369 };
370
371 vreg_l8c: ldo8 {
372 regulator-name = "vreg_l8c";
373 regulator-min-microvolt = <2400000>;
374 regulator-max-microvolt = <3300000>;
375 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
376 regulator-allow-set-load;
377 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
378 RPMH_REGULATOR_MODE_HPM>;
379 };
380
381 vreg_l9c: ldo9 {
382 regulator-name = "vreg_l9c";
383 regulator-min-microvolt = <1650000>;
384 regulator-max-microvolt = <2700000>;
385 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
386 regulator-allow-set-load;
387 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
388 RPMH_REGULATOR_MODE_HPM>;
389 };
390 };
391
392 regulators-2 {
393 compatible = "qcom,pmm8654au-rpmh-regulators";
394 qcom,pmic-id = "e";
395
396 vreg_s4e: smps4 {
397 regulator-name = "vreg_s4e";
398 regulator-min-microvolt = <970000>;
399 regulator-max-microvolt = <1520000>;
400 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
401 };
402
403 vreg_s7e: smps7 {
404 regulator-name = "vreg_s7e";
405 regulator-min-microvolt = <1010000>;
406 regulator-max-microvolt = <1170000>;
407 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
408 };
409
410 vreg_s9e: smps9 {
411 regulator-name = "vreg_s9e";
412 regulator-min-microvolt = <300000>;
413 regulator-max-microvolt = <570000>;
414 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
415 };
416
417 vreg_l6e: ldo6 {
418 regulator-name = "vreg_l6e";
419 regulator-min-microvolt = <1280000>;
420 regulator-max-microvolt = <1450000>;
421 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
422 regulator-allow-set-load;
423 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
424 RPMH_REGULATOR_MODE_HPM>;
425 };
426
427 vreg_l8e: ldo8 {
428 regulator-name = "vreg_l8e";
429 regulator-min-microvolt = <1800000>;
430 regulator-max-microvolt = <1950000>;
431 regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
432 regulator-allow-set-load;
433 regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
434 RPMH_REGULATOR_MODE_HPM>;
435 };
436 };
437 };
438
439 &gpu {
440 status = "okay";
441 };
442
443 &gpu_zap_shader {
444 firmware-name = "qcom/sa8775p/a663_zap.mbn";
445 };
446
447 &i2c11 {
448 clock-frequency = <400000>;
449 status = "okay";
450 };
451
452 &i2c18 {
453 clock-frequency = <400000>;
454
455 status = "okay";
456
457 io_expander: gpio@74 {
458 compatible = "ti,tca9539";
459 reg = <0x74>;
460 interrupts-extended = <&tlmm 98 IRQ_TYPE_EDGE_BOTH>;
461 gpio-controller;
462 #gpio-cells = <2>;
463 interrupt-controller;
464 #interrupt-cells = <2>;
465 reset-gpios = <&tlmm 97 GPIO_ACTIVE_LOW>;
466
467 pinctrl-0 = <&io_expander_intr_active>,
468 <&io_expander_reset_active>;
469 pinctrl-names = "default";
470 };
471
472 i2c-mux@70 {
473 compatible = "nxp,pca9543";
474 #address-cells = <1>;
475
476 #size-cells = <0>;
477 reg = <0x70>;
478
479 i2c@0 {
480 reg = <0>;
481 #address-cells = <1>;
482 #size-cells = <0>;
483
484 bridge@58 {
485 compatible = "analogix,anx7625";
486 reg = <0x58>;
487 interrupts-extended = <&io_expander 2 IRQ_TYPE_EDGE_FALLING>;
488 enable-gpios = <&io_expander 1 GPIO_ACTIVE_HIGH>;
489 reset-gpios = <&io_expander 0 GPIO_ACTIVE_HIGH>;
490 vdd10-supply = <&vreg_1p0>;
491 vdd18-supply = <&vreg_1p8>;
492 vdd33-supply = <&vreg_3p0>;
493
494 ports {
495 #address-cells = <1>;
496 #size-cells = <0>;
497
498 port@0 {
499 reg = <0>;
500
501 dsi2dp_bridge0_in: endpoint {
502 remote-endpoint = <&mdss0_dsi0_out>;
503 };
504 };
505
506 port@1 {
507 reg = <1>;
508
509 dsi2dp_bridge0_out: endpoint {
510 remote-endpoint = <&dp_dsi0_connector_in>;
511 };
512 };
513 };
514 };
515 };
516
517 i2c@1 {
518 reg = <1>;
519 #address-cells = <1>;
520 #size-cells = <0>;
521
522 bridge@58 {
523 compatible = "analogix,anx7625";
524 reg = <0x58>;
525 interrupts-extended = <&io_expander 10 IRQ_TYPE_EDGE_FALLING>;
526 enable-gpios = <&io_expander 9 GPIO_ACTIVE_HIGH>;
527 reset-gpios = <&io_expander 8 GPIO_ACTIVE_HIGH>;
528 vdd10-supply = <&vreg_1p0>;
529 vdd18-supply = <&vreg_1p8>;
530 vdd33-supply = <&vreg_3p0>;
531
532 ports {
533 #address-cells = <1>;
534 #size-cells = <0>;
535
536 port@0 {
537 reg = <0>;
538
539 dsi2dp_bridge1_in: endpoint {
540 remote-endpoint = <&mdss0_dsi1_out>;
541 };
542 };
543
544 port@1 {
545 reg = <1>;
546
547 dsi2dp_bridge1_out: endpoint {
548 remote-endpoint = <&dp_dsi1_connector_in>;
549 };
550 };
551 };
552 };
553 };
554 };
555
556 };
557
558 &iris {
559 firmware-name = "qcom/vpu/vpu30_p4_s6.mbn";
560
561 status = "okay";
562 };
563
564 &mdss0 {
565 status = "okay";
566 };
567
568 &mdss0_dp0 {
569 pinctrl-0 = <&dp0_hot_plug_det>;
570 pinctrl-names = "default";
571
572 status = "okay";
573 };
574
575 &mdss0_dp0_out {
576 data-lanes = <0 1 2 3>;
577 link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
578 remote-endpoint = <&dp0_connector_in>;
579 };
580
581 &mdss0_dp0_phy {
582 vdda-phy-supply = <&vreg_l1c>;
583 vdda-pll-supply = <&vreg_l4a>;
584
585 status = "okay";
586 };
587
588 &mdss0_dp1 {
589 pinctrl-0 = <&dp1_hot_plug_det>;
590 pinctrl-names = "default";
591
592 status = "okay";
593 };
594
595 &mdss0_dp1_out {
596 data-lanes = <0 1 2 3>;
597 link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
598 remote-endpoint = <&dp1_connector_in>;
599 };
600
601 &mdss0_dp1_phy {
602 vdda-phy-supply = <&vreg_l1c>;
603 vdda-pll-supply = <&vreg_l4a>;
604
605 status = "okay";
606 };
607
608 &mdss0_dsi0 {
609 vdda-supply = <&vreg_l1c>;
610
611 status = "okay";
612 };
613
614 &mdss0_dsi0_out {
615 data-lanes = <0 1 2 3>;
616 remote-endpoint = <&dsi2dp_bridge0_in>;
617 };
618
619 &mdss0_dsi0_phy {
620 vdds-supply = <&vreg_l4a>;
621
622 status = "okay";
623 };
624
625 &mdss0_dsi1 {
626 vdda-supply = <&vreg_l1c>;
627
628 status = "okay";
629 };
630
631 &mdss0_dsi1_out {
632 data-lanes = <0 1 2 3>;
633 remote-endpoint = <&dsi2dp_bridge1_in>;
634 };
635
636 &mdss0_dsi1_phy {
637 vdds-supply = <&vreg_l4a>;
638
639 status = "okay";
640 };
641
642 &pmm8654au_0_gpios {
643 gpio-line-names = "DS_EN",
644 "POFF_COMPLETE",
645 "UFS0_VER_ID",
646 "FAST_POFF",
647 "DBU1_PON_DONE",
648 "AOSS_SLEEP",
649 "CAM_DES0_EN",
650 "CAM_DES1_EN",
651 "CAM_DES2_EN",
652 "CAM_DES3_EN",
653 "UEFI",
654 "ANALOG_PON_OPT";
655 };
656
657 &pmm8654au_0_pon_resin {
658 linux,code = <KEY_VOLUMEDOWN>;
659 status = "okay";
660 };
661
662 &pmm8654au_1_gpios {
663 gpio-line-names = "PMIC_C_ID0",
664 "PMIC_C_ID1",
665 "UFS1_VER_ID",
666 "IPA_PWR",
667 "",
668 "WLAN_DBU4_EN",
669 "WLAN_EN",
670 "BT_EN",
671 "USB2_PWR_EN",
672 "USB2_FAULT";
673
674 wlan_en_state: wlan-en-state {
675 pins = "gpio7";
676 function = "normal";
677 output-low;
678 bias-pull-down;
679 };
680
681 bt_en_state: bt-en-state {
682 pins = "gpio8";
683 function = "normal";
684 output-low;
685 bias-pull-down;
686 };
687
688 usb2_en_state: usb2-en-state {
689 pins = "gpio9";
690 function = "normal";
691 output-high;
692 power-source = <0>;
693 };
694 };
695
696 &pmm8654au_2_gpios {
697 gpio-line-names = "PMIC_E_ID0",
698 "PMIC_E_ID1",
699 "USB0_PWR_EN",
700 "USB0_FAULT",
701 "SENSOR_IRQ_1",
702 "SENSOR_IRQ_2",
703 "SENSOR_RST",
704 "SGMIIO0_RST",
705 "SGMIIO1_RST",
706 "USB1_PWR_ENABLE",
707 "USB1_FAULT",
708 "VMON_SPX8";
709
710 usb0_en_state: usb0-en-state {
711 pins = "gpio3";
712 function = "normal";
713 output-high;
714 power-source = <0>;
715 };
716
717 usb1_en_state: usb1-en-state {
718 pins = "gpio10";
719 function = "normal";
720 output-high;
721 power-source = <0>;
722 };
723 };
724
725 &pmm8654au_3_gpios {
726 gpio-line-names = "PMIC_G_ID0",
727 "PMIC_G_ID1",
728 "GNSS_RST",
729 "GNSS_EN",
730 "GNSS_BOOT_MODE";
731 };
732
733 &qupv3_id_1 {
734 status = "okay";
735 };
736
737 &qupv3_id_2 {
738 status = "okay";
739 };
740
741 &qup_spi16_default {
742 drive-strength = <6>;
743 bias-disable;
744 };
745
746 &qup_i2c11_default {
747 drive-strength = <2>;
748 bias-pull-up;
749 };
750
751 &qup_i2c18_default {
752 drive-strength = <2>;
753 bias-pull-up;
754 };
755
756 &qup_uart12_cts {
757 bias-disable;
758 };
759
760 &qup_uart12_rts {
761 bias-pull-down;
762 };
763
764 &qup_uart12_tx {
765 bias-pull-up;
766 };
767
768 &qup_uart12_rx {
769 bias-pull-down;
770 };
771
772 &qup_uart17_cts {
773 bias-disable;
774 };
775
776 &qup_uart17_rts {
777 bias-pull-down;
778 };
779
780 &qup_uart17_tx {
781 bias-pull-up;
782 };
783
784 &qup_uart17_rx {
785 bias-pull-down;
786 };
787
788 &serdes0 {
789 phy-supply = <&vreg_l5a>;
790 status = "okay";
791 };
792
793 &serdes1 {
794 phy-supply = <&vreg_l5a>;
795 status = "okay";
796 };
797
798 &sleep_clk {
799 clock-frequency = <32000>;
800 };
801
802 &spi16 {
803 status = "okay";
804 };
805
806 &tlmm {
807 dp0_hot_plug_det: dp0-hot-plug-det-state {
808 pins = "gpio101";
809 function = "edp0_hot";
810 bias-disable;
811 };
812
813 dp1_hot_plug_det: dp1-hot-plug-det-state {
814 pins = "gpio102";
815 function = "edp1_hot";
816 bias-disable;
817 };
818
819 io_expander_intr_active: io-expander-intr-active-state {
820 pins = "gpio98";
821 function = "gpio";
822 drive-strength = <2>;
823 bias-disable;
824 };
825
826 io_expander_reset_active: io-expander-reset-active-state {
827 pins = "gpio97";
828 function = "gpio";
829 drive-strength = <2>;
830 bias-disable;
831 output-high;
832 };
833
834 pcie0_default_state: pcie0-default-state {
835 perst-pins {
836 pins = "gpio2";
837 function = "gpio";
838 drive-strength = <2>;
839 bias-pull-down;
840 };
841
842 clkreq-pins {
843 pins = "gpio1";
844 function = "pcie0_clkreq";
845 drive-strength = <2>;
846 bias-pull-up;
847 };
848
849 wake-pins {
850 pins = "gpio0";
851 function = "gpio";
852 drive-strength = <2>;
853 bias-pull-up;
854 };
855 };
856
857 pcie1_default_state: pcie1-default-state {
858 perst-pins {
859 pins = "gpio4";
860 function = "gpio";
861 drive-strength = <2>;
862 bias-pull-down;
863 };
864
865 clkreq-pins {
866 pins = "gpio3";
867 function = "pcie1_clkreq";
868 drive-strength = <2>;
869 bias-pull-up;
870 };
871
872 wake-pins {
873 pins = "gpio5";
874 function = "gpio";
875 drive-strength = <2>;
876 bias-pull-up;
877 };
878 };
879 };
880
881 &pcie0 {
882 perst-gpios = <&tlmm 2 GPIO_ACTIVE_LOW>;
883 wake-gpios = <&tlmm 0 GPIO_ACTIVE_HIGH>;
884
885 pinctrl-names = "default";
886 pinctrl-0 = <&pcie0_default_state>;
887
888 status = "okay";
889 };
890
891 &pcie1 {
892 perst-gpios = <&tlmm 4 GPIO_ACTIVE_LOW>;
893 wake-gpios = <&tlmm 5 GPIO_ACTIVE_HIGH>;
894
895 pinctrl-names = "default";
896 pinctrl-0 = <&pcie1_default_state>;
897
898 status = "okay";
899 };
900
901 &pcie0_phy {
902 vdda-phy-supply = <&vreg_l5a>;
903 vdda-pll-supply = <&vreg_l1c>;
904
905 status = "okay";
906 };
907
908 &pcie1_phy {
909 vdda-phy-supply = <&vreg_l5a>;
910 vdda-pll-supply = <&vreg_l1c>;
911
912 status = "okay";
913 };
914
915 &pcieport0 {
916 wifi@0 {
917 compatible = "pci17cb,1101";
918 reg = <0x10000 0x0 0x0 0x0 0x0>;
919
920 qcom,calibration-variant = "QC_SA8775P_Ride";
921
922 vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
923 vddaon-supply = <&vreg_pmu_aon_0p59>;
924 vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
925 vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
926 vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
927 vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
928 vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>;
929 vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
930 vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
931 };
932 };
933
934 &remoteproc_adsp {
935 firmware-name = "qcom/sa8775p/adsp.mbn";
936 status = "okay";
937 };
938
939 &remoteproc_cdsp0 {
940 firmware-name = "qcom/sa8775p/cdsp0.mbn";
941 status = "okay";
942 };
943
944 &remoteproc_cdsp1 {
945 firmware-name = "qcom/sa8775p/cdsp1.mbn";
946 status = "okay";
947 };
948
949 &remoteproc_gpdsp0 {
950 firmware-name = "qcom/sa8775p/gpdsp0.mbn";
951 status = "okay";
952 };
953
954 &remoteproc_gpdsp1 {
955 firmware-name = "qcom/sa8775p/gpdsp1.mbn";
956 status = "okay";
957 };
958
959 &uart10 {
960 compatible = "qcom,geni-debug-uart";
961 status = "okay";
962 };
963
964 &uart12 {
965 pinctrl-0 = <&qup_uart12_default>;
966 pinctrl-names = "default";
967 status = "okay";
968 };
969
970 &uart17 {
971 pinctrl-0 = <&qup_uart17_default>;
972 pinctrl-names = "default";
973 status = "okay";
974
975 bluetooth {
976 compatible = "qcom,wcn6855-bt";
977 firmware-name = "QCA6698/hpnv21", "QCA6698/hpbtfw21.tlv";
978
979 vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
980 vddaon-supply = <&vreg_pmu_aon_0p59>;
981 vddbtcmx-supply = <&vreg_pmu_btcmx_0p85>;
982 vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
983 vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
984 vddrfa1p7-supply = <&vreg_pmu_rfa_1p7>;
985 };
986 };
987
988 &ufs_mem_hc {
989 reset-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>;
990 vcc-supply = <&vreg_l8a>;
991 vcc-max-microamp = <1100000>;
992 vccq-supply = <&vreg_l4c>;
993 vccq-max-microamp = <1200000>;
994
995 status = "okay";
996 };
997
998 &ufs_mem_phy {
999 vdda-phy-supply = <&vreg_l4a>;
1000 vdda-pll-supply = <&vreg_l1c>;
1001
1002 status = "okay";
1003 };
1004
1005 &usb_0 {
1006 pinctrl-names = "default";
1007 pinctrl-0 = <&usb0_en_state>;
1008 dr_mode = "peripheral";
1009
1010 status = "okay";
1011 };
1012
1013 &usb_0_hsphy {
1014 vdda-pll-supply = <&vreg_l7a>;
1015 vdda18-supply = <&vreg_l6c>;
1016 vdda33-supply = <&vreg_l9a>;
1017
1018 status = "okay";
1019 };
1020
1021 &usb_0_qmpphy {
1022 vdda-phy-supply = <&vreg_l1c>;
1023 vdda-pll-supply = <&vreg_l7a>;
1024
1025 status = "okay";
1026 };
1027
1028 &usb_1 {
1029 pinctrl-names = "default";
1030 pinctrl-0 = <&usb1_en_state>;
1031 dr_mode = "host";
1032
1033 status = "okay";
1034 };
1035
1036 &usb_1_hsphy {
1037 vdda-pll-supply = <&vreg_l7a>;
1038 vdda18-supply = <&vreg_l6c>;
1039 vdda33-supply = <&vreg_l9a>;
1040
1041 status = "okay";
1042 };
1043
1044 &usb_1_qmpphy {
1045 vdda-phy-supply = <&vreg_l1c>;
1046 vdda-pll-supply = <&vreg_l7a>;
1047
1048 status = "okay";
1049 };
1050
1051 &usb_2 {
1052 pinctrl-names = "default";
1053 pinctrl-0 = <&usb2_en_state>;
1054 dr_mode = "host";
1055
1056 status = "okay";
1057 };
1058
1059 &usb_2_hsphy {
1060 vdda-pll-supply = <&vreg_l7a>;
1061 vdda18-supply = <&vreg_l6c>;
1062 vdda33-supply = <&vreg_l9a>;
1063
1064 status = "okay";
1065 };
1066
1067 &xo_board_clk {
1068 clock-frequency = <38400000>;
1069 };