| 1 |
// SPDX-License-Identifier: BSD-3-Clause |
| 2 |
/* |
| 3 |
* Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries. |
| 4 |
*/ |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
|
| 8 |
#include <dt-bindings/leds/common.h> |
| 9 |
#include "hamoa-iot-som.dtsi" |
| 10 |
#include <dt-bindings/pinctrl/qcom,pmic-gpio.h> |
| 11 |
|
| 12 |
/ { |
| 13 |
model = "Qualcomm Technologies, Inc. Hamoa IoT EVK"; |
| 14 |
compatible = "qcom,hamoa-iot-evk", "qcom,hamoa-iot-som", "qcom,x1e80100"; |
| 15 |
chassis-type = "embedded"; |
| 16 |
|
| 17 |
aliases { |
| 18 |
serial0 = &uart21; |
| 19 |
serial1 = &uart14; |
| 20 |
}; |
| 21 |
|
| 22 |
backlight: backlight { |
| 23 |
compatible = "pwm-backlight"; |
| 24 |
pwms = <&pmk8550_pwm 0 5000000>; |
| 25 |
enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>; |
| 26 |
power-supply = <&vreg_edp_bl>; |
| 27 |
|
| 28 |
pinctrl-0 = <&edp_bl_en>, <&edp_bl_pwm>; |
| 29 |
pinctrl-names = "default"; |
| 30 |
}; |
| 31 |
|
| 32 |
wcd938x: audio-codec { |
| 33 |
compatible = "qcom,wcd9385-codec"; |
| 34 |
|
| 35 |
pinctrl-0 = <&wcd_default>; |
| 36 |
pinctrl-names = "default"; |
| 37 |
|
| 38 |
reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>; |
| 39 |
|
| 40 |
qcom,micbias1-microvolt = <1800000>; |
| 41 |
qcom,micbias2-microvolt = <1800000>; |
| 42 |
qcom,micbias3-microvolt = <1800000>; |
| 43 |
qcom,micbias4-microvolt = <1800000>; |
| 44 |
qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 |
| 45 |
500000 500000 500000 500000>; |
| 46 |
qcom,mbhc-headset-vthreshold-microvolt = <1700000>; |
| 47 |
qcom,mbhc-headphone-vthreshold-microvolt = <50000>; |
| 48 |
qcom,rx-device = <&wcd_rx>; |
| 49 |
qcom,tx-device = <&wcd_tx>; |
| 50 |
|
| 51 |
vdd-buck-supply = <&vreg_l15b_1p8>; |
| 52 |
vdd-rxtx-supply = <&vreg_l15b_1p8>; |
| 53 |
vdd-io-supply = <&vreg_l15b_1p8>; |
| 54 |
vdd-mic-bias-supply = <&vreg_bob1>; |
| 55 |
|
| 56 |
#sound-dai-cells = <1>; |
| 57 |
}; |
| 58 |
|
| 59 |
chosen { |
| 60 |
stdout-path = "serial0:115200n8"; |
| 61 |
}; |
| 62 |
|
| 63 |
connector3 { |
| 64 |
compatible = "usb-a-connector"; |
| 65 |
label = "USB-3-Type-A"; |
| 66 |
power-role = "source"; |
| 67 |
|
| 68 |
vbus-supply = <®ulator_usb3_vbus>; |
| 69 |
|
| 70 |
port { |
| 71 |
connector_3_in: endpoint { |
| 72 |
}; |
| 73 |
}; |
| 74 |
}; |
| 75 |
|
| 76 |
connector6 { |
| 77 |
compatible = "usb-a-connector"; |
| 78 |
label = "USB-6-Type-A"; |
| 79 |
power-role = "source"; |
| 80 |
|
| 81 |
vbus-supply = <®ulator_usb6_vbus>; |
| 82 |
|
| 83 |
port { |
| 84 |
connector_4_in: endpoint { |
| 85 |
}; |
| 86 |
}; |
| 87 |
}; |
| 88 |
|
| 89 |
pmic-glink { |
| 90 |
compatible = "qcom,x1e80100-pmic-glink", |
| 91 |
"qcom,sm8550-pmic-glink", |
| 92 |
"qcom,pmic-glink"; |
| 93 |
#address-cells = <1>; |
| 94 |
#size-cells = <0>; |
| 95 |
orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>, |
| 96 |
<&tlmm 123 GPIO_ACTIVE_HIGH>, |
| 97 |
<&tlmm 125 GPIO_ACTIVE_HIGH>; |
| 98 |
|
| 99 |
connector@0 { |
| 100 |
compatible = "usb-c-connector"; |
| 101 |
reg = <0>; |
| 102 |
power-role = "dual"; |
| 103 |
data-role = "dual"; |
| 104 |
|
| 105 |
ports { |
| 106 |
#address-cells = <1>; |
| 107 |
#size-cells = <0>; |
| 108 |
|
| 109 |
port@0 { |
| 110 |
reg = <0>; |
| 111 |
|
| 112 |
pmic_glink_ss0_hs_in: endpoint { |
| 113 |
remote-endpoint = <&usb_1_ss0_dwc3_hs>; |
| 114 |
}; |
| 115 |
}; |
| 116 |
|
| 117 |
port@1 { |
| 118 |
reg = <1>; |
| 119 |
|
| 120 |
pmic_glink_ss0_ss_in: endpoint { |
| 121 |
remote-endpoint = <&usb_1_ss0_qmpphy_out>; |
| 122 |
}; |
| 123 |
}; |
| 124 |
|
| 125 |
port@2 { |
| 126 |
reg = <2>; |
| 127 |
|
| 128 |
pmic_glink_ss0_sbu: endpoint { |
| 129 |
remote-endpoint = <&usb_1_ss0_sbu_mux>; |
| 130 |
}; |
| 131 |
}; |
| 132 |
}; |
| 133 |
}; |
| 134 |
|
| 135 |
connector@1 { |
| 136 |
compatible = "usb-c-connector"; |
| 137 |
reg = <1>; |
| 138 |
power-role = "dual"; |
| 139 |
data-role = "dual"; |
| 140 |
|
| 141 |
ports { |
| 142 |
#address-cells = <1>; |
| 143 |
#size-cells = <0>; |
| 144 |
|
| 145 |
port@0 { |
| 146 |
reg = <0>; |
| 147 |
|
| 148 |
pmic_glink_ss1_hs_in: endpoint { |
| 149 |
remote-endpoint = <&usb_1_ss1_dwc3_hs>; |
| 150 |
}; |
| 151 |
}; |
| 152 |
|
| 153 |
port@1 { |
| 154 |
reg = <1>; |
| 155 |
|
| 156 |
pmic_glink_ss1_ss_in: endpoint { |
| 157 |
remote-endpoint = <&retimer_ss1_ss_out>; |
| 158 |
}; |
| 159 |
}; |
| 160 |
|
| 161 |
port@2 { |
| 162 |
reg = <2>; |
| 163 |
|
| 164 |
pmic_glink_ss1_con_sbu_in: endpoint { |
| 165 |
remote-endpoint = <&retimer_ss1_con_sbu_out>; |
| 166 |
}; |
| 167 |
}; |
| 168 |
}; |
| 169 |
}; |
| 170 |
|
| 171 |
connector@2 { |
| 172 |
compatible = "usb-c-connector"; |
| 173 |
reg = <2>; |
| 174 |
power-role = "dual"; |
| 175 |
data-role = "dual"; |
| 176 |
|
| 177 |
ports { |
| 178 |
#address-cells = <1>; |
| 179 |
#size-cells = <0>; |
| 180 |
|
| 181 |
port@0 { |
| 182 |
reg = <0>; |
| 183 |
|
| 184 |
pmic_glink_ss2_hs_in: endpoint { |
| 185 |
remote-endpoint = <&usb_1_ss2_dwc3_hs>; |
| 186 |
}; |
| 187 |
}; |
| 188 |
|
| 189 |
port@1 { |
| 190 |
reg = <1>; |
| 191 |
|
| 192 |
pmic_glink_ss2_ss_in: endpoint { |
| 193 |
remote-endpoint = <&retimer_ss2_ss_out>; |
| 194 |
}; |
| 195 |
}; |
| 196 |
|
| 197 |
port@2 { |
| 198 |
reg = <2>; |
| 199 |
|
| 200 |
pmic_glink_ss2_con_sbu_in: endpoint { |
| 201 |
remote-endpoint = <&retimer_ss2_con_sbu_out>; |
| 202 |
}; |
| 203 |
}; |
| 204 |
}; |
| 205 |
}; |
| 206 |
}; |
| 207 |
|
| 208 |
vreg_edp_3p3: regulator-edp-3p3 { |
| 209 |
compatible = "regulator-fixed"; |
| 210 |
|
| 211 |
regulator-name = "VREG_EDP_3P3"; |
| 212 |
regulator-min-microvolt = <3300000>; |
| 213 |
regulator-max-microvolt = <3300000>; |
| 214 |
|
| 215 |
gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>; |
| 216 |
enable-active-high; |
| 217 |
|
| 218 |
pinctrl-0 = <&edp_reg_en>; |
| 219 |
pinctrl-names = "default"; |
| 220 |
|
| 221 |
regulator-boot-on; |
| 222 |
}; |
| 223 |
|
| 224 |
vreg_edp_bl: regulator-edp-bl { |
| 225 |
compatible = "regulator-fixed"; |
| 226 |
|
| 227 |
regulator-name = "VBL9"; |
| 228 |
regulator-min-microvolt = <3600000>; |
| 229 |
regulator-max-microvolt = <3600000>; |
| 230 |
|
| 231 |
gpio = <&pmc8380_3_gpios 10 GPIO_ACTIVE_HIGH>; |
| 232 |
enable-active-high; |
| 233 |
|
| 234 |
pinctrl-0 = <&edp_bl_reg_en>; |
| 235 |
pinctrl-names = "default"; |
| 236 |
|
| 237 |
regulator-boot-on; |
| 238 |
}; |
| 239 |
|
| 240 |
vreg_nvme: regulator-nvme { |
| 241 |
compatible = "regulator-fixed"; |
| 242 |
|
| 243 |
regulator-name = "VREG_NVME_3P3"; |
| 244 |
regulator-min-microvolt = <3300000>; |
| 245 |
regulator-max-microvolt = <3300000>; |
| 246 |
|
| 247 |
gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>; |
| 248 |
enable-active-high; |
| 249 |
|
| 250 |
pinctrl-0 = <&nvme_reg_en>; |
| 251 |
pinctrl-names = "default"; |
| 252 |
|
| 253 |
regulator-boot-on; |
| 254 |
}; |
| 255 |
|
| 256 |
vreg_pcie_12v: regulator-pcie-12v { |
| 257 |
compatible = "regulator-fixed"; |
| 258 |
|
| 259 |
regulator-name = "VREG_PCIE_12V"; |
| 260 |
regulator-min-microvolt = <12000000>; |
| 261 |
regulator-max-microvolt = <12000000>; |
| 262 |
|
| 263 |
gpio = <&pm8550ve_8_gpios 8 GPIO_ACTIVE_HIGH>; |
| 264 |
enable-active-high; |
| 265 |
|
| 266 |
pinctrl-0 = <&pcie_x8_12v>; |
| 267 |
pinctrl-names = "default"; |
| 268 |
}; |
| 269 |
|
| 270 |
vreg_pcie_3v3: regulator-pcie-3v3 { |
| 271 |
compatible = "regulator-fixed"; |
| 272 |
|
| 273 |
regulator-name = "VREG_PCIE_3P3"; |
| 274 |
regulator-min-microvolt = <3300000>; |
| 275 |
regulator-max-microvolt = <3300000>; |
| 276 |
|
| 277 |
gpio = <&pmc8380_3_gpios 6 GPIO_ACTIVE_HIGH>; |
| 278 |
enable-active-high; |
| 279 |
|
| 280 |
pinctrl-0 = <&pm_sde7_main_3p3_en>; |
| 281 |
pinctrl-names = "default"; |
| 282 |
}; |
| 283 |
|
| 284 |
vreg_pcie_3v3_aux: regulator-pcie-3v3-aux { |
| 285 |
compatible = "regulator-fixed"; |
| 286 |
|
| 287 |
regulator-name = "VREG_PCIE_3P3_AUX"; |
| 288 |
regulator-min-microvolt = <3300000>; |
| 289 |
regulator-max-microvolt = <3300000>; |
| 290 |
|
| 291 |
gpio = <&pmc8380_3_gpios 8 GPIO_ACTIVE_HIGH>; |
| 292 |
enable-active-high; |
| 293 |
|
| 294 |
pinctrl-0 = <&pm_sde7_aux_3p3_en>; |
| 295 |
pinctrl-names = "default"; |
| 296 |
}; |
| 297 |
|
| 298 |
/* Left unused as the retimer is not used on this board. */ |
| 299 |
vreg_rtmr0_1p15: regulator-rtmr0-1p15 { |
| 300 |
compatible = "regulator-fixed"; |
| 301 |
|
| 302 |
regulator-name = "VREG_RTMR0_1P15"; |
| 303 |
regulator-min-microvolt = <1150000>; |
| 304 |
regulator-max-microvolt = <1150000>; |
| 305 |
|
| 306 |
gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>; |
| 307 |
enable-active-high; |
| 308 |
|
| 309 |
pinctrl-0 = <&usb0_pwr_1p15_reg_en>; |
| 310 |
pinctrl-names = "default"; |
| 311 |
|
| 312 |
regulator-boot-on; |
| 313 |
}; |
| 314 |
|
| 315 |
vreg_rtmr0_1p8: regulator-rtmr0-1p8 { |
| 316 |
compatible = "regulator-fixed"; |
| 317 |
|
| 318 |
regulator-name = "VREG_RTMR0_1P8"; |
| 319 |
regulator-min-microvolt = <1800000>; |
| 320 |
regulator-max-microvolt = <1800000>; |
| 321 |
|
| 322 |
gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>; |
| 323 |
enable-active-high; |
| 324 |
|
| 325 |
pinctrl-0 = <&usb0_1p8_reg_en>; |
| 326 |
pinctrl-names = "default"; |
| 327 |
|
| 328 |
regulator-boot-on; |
| 329 |
}; |
| 330 |
|
| 331 |
vreg_rtmr0_3p3: regulator-rtmr0-3p3 { |
| 332 |
compatible = "regulator-fixed"; |
| 333 |
|
| 334 |
regulator-name = "VREG_RTMR0_3P3"; |
| 335 |
regulator-min-microvolt = <3300000>; |
| 336 |
regulator-max-microvolt = <3300000>; |
| 337 |
|
| 338 |
gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>; |
| 339 |
enable-active-high; |
| 340 |
|
| 341 |
pinctrl-0 = <&usb0_3p3_reg_en>; |
| 342 |
pinctrl-names = "default"; |
| 343 |
|
| 344 |
regulator-boot-on; |
| 345 |
}; |
| 346 |
|
| 347 |
vreg_rtmr1_1p15: regulator-rtmr1-1p15 { |
| 348 |
compatible = "regulator-fixed"; |
| 349 |
|
| 350 |
regulator-name = "VREG_RTMR1_1P15"; |
| 351 |
regulator-min-microvolt = <1150000>; |
| 352 |
regulator-max-microvolt = <1150000>; |
| 353 |
|
| 354 |
gpio = <&tlmm 188 GPIO_ACTIVE_HIGH>; |
| 355 |
enable-active-high; |
| 356 |
|
| 357 |
pinctrl-0 = <&usb1_pwr_1p15_reg_en>; |
| 358 |
pinctrl-names = "default"; |
| 359 |
|
| 360 |
regulator-boot-on; |
| 361 |
}; |
| 362 |
|
| 363 |
vreg_rtmr1_1p8: regulator-rtmr1-1p8 { |
| 364 |
compatible = "regulator-fixed"; |
| 365 |
|
| 366 |
regulator-name = "VREG_RTMR1_1P8"; |
| 367 |
regulator-min-microvolt = <1800000>; |
| 368 |
regulator-max-microvolt = <1800000>; |
| 369 |
|
| 370 |
gpio = <&tlmm 175 GPIO_ACTIVE_HIGH>; |
| 371 |
enable-active-high; |
| 372 |
|
| 373 |
pinctrl-0 = <&usb1_pwr_1p8_reg_en>; |
| 374 |
pinctrl-names = "default"; |
| 375 |
|
| 376 |
regulator-boot-on; |
| 377 |
}; |
| 378 |
|
| 379 |
vreg_rtmr1_3p3: regulator-rtmr1-3p3 { |
| 380 |
compatible = "regulator-fixed"; |
| 381 |
|
| 382 |
regulator-name = "VREG_RTMR1_3P3"; |
| 383 |
regulator-min-microvolt = <3300000>; |
| 384 |
regulator-max-microvolt = <3300000>; |
| 385 |
|
| 386 |
gpio = <&tlmm 186 GPIO_ACTIVE_HIGH>; |
| 387 |
enable-active-high; |
| 388 |
|
| 389 |
pinctrl-0 = <&usb1_pwr_3p3_reg_en>; |
| 390 |
pinctrl-names = "default"; |
| 391 |
|
| 392 |
regulator-boot-on; |
| 393 |
}; |
| 394 |
|
| 395 |
vreg_rtmr2_1p15: regulator-rtmr2-1p15 { |
| 396 |
compatible = "regulator-fixed"; |
| 397 |
|
| 398 |
regulator-name = "VREG_RTMR2_1P15"; |
| 399 |
regulator-min-microvolt = <1150000>; |
| 400 |
regulator-max-microvolt = <1150000>; |
| 401 |
|
| 402 |
gpio = <&tlmm 189 GPIO_ACTIVE_HIGH>; |
| 403 |
enable-active-high; |
| 404 |
|
| 405 |
pinctrl-0 = <&usb2_pwr_1p15_reg_en>; |
| 406 |
pinctrl-names = "default"; |
| 407 |
|
| 408 |
regulator-boot-on; |
| 409 |
}; |
| 410 |
|
| 411 |
vreg_rtmr2_1p8: regulator-rtmr2-1p8 { |
| 412 |
compatible = "regulator-fixed"; |
| 413 |
|
| 414 |
regulator-name = "VREG_RTMR2_1P8"; |
| 415 |
regulator-min-microvolt = <1800000>; |
| 416 |
regulator-max-microvolt = <1800000>; |
| 417 |
|
| 418 |
gpio = <&tlmm 126 GPIO_ACTIVE_HIGH>; |
| 419 |
enable-active-high; |
| 420 |
|
| 421 |
pinctrl-0 = <&usb2_pwr_1p8_reg_en>; |
| 422 |
pinctrl-names = "default"; |
| 423 |
|
| 424 |
regulator-boot-on; |
| 425 |
}; |
| 426 |
|
| 427 |
vreg_rtmr2_3p3: regulator-rtmr2-3p3 { |
| 428 |
compatible = "regulator-fixed"; |
| 429 |
|
| 430 |
regulator-name = "VREG_RTMR2_3P3"; |
| 431 |
regulator-min-microvolt = <3300000>; |
| 432 |
regulator-max-microvolt = <3300000>; |
| 433 |
|
| 434 |
gpio = <&tlmm 187 GPIO_ACTIVE_HIGH>; |
| 435 |
enable-active-high; |
| 436 |
|
| 437 |
pinctrl-0 = <&usb2_pwr_3p3_reg_en>; |
| 438 |
pinctrl-names = "default"; |
| 439 |
|
| 440 |
regulator-boot-on; |
| 441 |
}; |
| 442 |
|
| 443 |
regulator_usb3_vbus: regulator-usb3-vbus { |
| 444 |
compatible = "regulator-fixed"; |
| 445 |
regulator-name = "USB3_VBUS"; |
| 446 |
gpio = <&pm8550ve_9_gpios 4 GPIO_ACTIVE_HIGH>; |
| 447 |
pinctrl-0 = <&usb3_en>; |
| 448 |
pinctrl-names = "default"; |
| 449 |
enable-active-high; |
| 450 |
regulator-always-on; |
| 451 |
}; |
| 452 |
|
| 453 |
regulator_usb6_vbus: regulator-usb6-vbus { |
| 454 |
compatible = "regulator-fixed"; |
| 455 |
regulator-name = "USB6_VBUS"; |
| 456 |
gpio = <&pm8550ve_9_gpios 5 GPIO_ACTIVE_HIGH>; |
| 457 |
pinctrl-0 = <&usb6_en>; |
| 458 |
pinctrl-names = "default"; |
| 459 |
enable-active-high; |
| 460 |
regulator-always-on; |
| 461 |
}; |
| 462 |
|
| 463 |
vph_pwr: regulator-vph-pwr { |
| 464 |
compatible = "regulator-fixed"; |
| 465 |
|
| 466 |
regulator-name = "vph_pwr"; |
| 467 |
regulator-min-microvolt = <3700000>; |
| 468 |
regulator-max-microvolt = <3700000>; |
| 469 |
|
| 470 |
regulator-always-on; |
| 471 |
regulator-boot-on; |
| 472 |
}; |
| 473 |
|
| 474 |
/* |
| 475 |
* TODO: These two regulators are actually part of the removable M.2 |
| 476 |
* card and not the EVK mainboard. Need to describe this differently. |
| 477 |
* Functionally it works correctly, because all we need to do is to |
| 478 |
* turn on the actual 3.3V supply above. |
| 479 |
*/ |
| 480 |
vreg_wcn_0p95: regulator-wcn-0p95 { |
| 481 |
compatible = "regulator-fixed"; |
| 482 |
|
| 483 |
regulator-name = "VREG_WCN_0P95"; |
| 484 |
regulator-min-microvolt = <950000>; |
| 485 |
regulator-max-microvolt = <950000>; |
| 486 |
|
| 487 |
vin-supply = <&vreg_wcn_3p3>; |
| 488 |
}; |
| 489 |
|
| 490 |
vreg_wcn_1p9: regulator-wcn-1p9 { |
| 491 |
compatible = "regulator-fixed"; |
| 492 |
|
| 493 |
regulator-name = "VREG_WCN_1P9"; |
| 494 |
regulator-min-microvolt = <1900000>; |
| 495 |
regulator-max-microvolt = <1900000>; |
| 496 |
|
| 497 |
vin-supply = <&vreg_wcn_3p3>; |
| 498 |
}; |
| 499 |
|
| 500 |
vreg_wcn_3p3: regulator-wcn-3p3 { |
| 501 |
compatible = "regulator-fixed"; |
| 502 |
|
| 503 |
regulator-name = "VREG_WCN_3P3"; |
| 504 |
regulator-min-microvolt = <3300000>; |
| 505 |
regulator-max-microvolt = <3300000>; |
| 506 |
|
| 507 |
gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>; |
| 508 |
enable-active-high; |
| 509 |
|
| 510 |
pinctrl-0 = <&wcn_sw_en>; |
| 511 |
pinctrl-names = "default"; |
| 512 |
|
| 513 |
regulator-always-on; |
| 514 |
regulator-boot-on; |
| 515 |
}; |
| 516 |
|
| 517 |
vreg_wwan: regulator-wwan { |
| 518 |
compatible = "regulator-fixed"; |
| 519 |
|
| 520 |
regulator-name = "SDX_VPH_PWR"; |
| 521 |
regulator-min-microvolt = <3300000>; |
| 522 |
regulator-max-microvolt = <3300000>; |
| 523 |
|
| 524 |
gpio = <&tlmm 221 GPIO_ACTIVE_HIGH>; |
| 525 |
enable-active-high; |
| 526 |
|
| 527 |
pinctrl-0 = <&wwan_sw_en>; |
| 528 |
pinctrl-names = "default"; |
| 529 |
|
| 530 |
regulator-boot-on; |
| 531 |
}; |
| 532 |
|
| 533 |
sound { |
| 534 |
compatible = "qcom,x1e80100-sndcard"; |
| 535 |
model = "X1E80100-EVK"; |
| 536 |
audio-routing = "WooferLeft IN", "WSA WSA_SPK1 OUT", |
| 537 |
"TweeterLeft IN", "WSA WSA_SPK2 OUT", |
| 538 |
"WooferRight IN", "WSA2 WSA_SPK2 OUT", |
| 539 |
"TweeterRight IN", "WSA2 WSA_SPK2 OUT", |
| 540 |
"IN1_HPHL", "HPHL_OUT", |
| 541 |
"IN2_HPHR", "HPHR_OUT", |
| 542 |
"AMIC2", "MIC BIAS2", |
| 543 |
"VA DMIC0", "MIC BIAS3", |
| 544 |
"VA DMIC1", "MIC BIAS3", |
| 545 |
"VA DMIC2", "MIC BIAS1", |
| 546 |
"VA DMIC3", "MIC BIAS1", |
| 547 |
"TX SWR_INPUT1", "ADC2_OUTPUT"; |
| 548 |
|
| 549 |
wcd-playback-dai-link { |
| 550 |
link-name = "WCD Playback"; |
| 551 |
|
| 552 |
codec { |
| 553 |
sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>; |
| 554 |
}; |
| 555 |
|
| 556 |
cpu { |
| 557 |
sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>; |
| 558 |
}; |
| 559 |
|
| 560 |
platform { |
| 561 |
sound-dai = <&q6apm>; |
| 562 |
}; |
| 563 |
}; |
| 564 |
|
| 565 |
wcd-capture-dai-link { |
| 566 |
link-name = "WCD Capture"; |
| 567 |
|
| 568 |
codec { |
| 569 |
sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>; |
| 570 |
}; |
| 571 |
|
| 572 |
cpu { |
| 573 |
sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>; |
| 574 |
}; |
| 575 |
|
| 576 |
platform { |
| 577 |
sound-dai = <&q6apm>; |
| 578 |
}; |
| 579 |
}; |
| 580 |
|
| 581 |
wsa-dai-link { |
| 582 |
link-name = "WSA Playback"; |
| 583 |
|
| 584 |
codec { |
| 585 |
sound-dai = <&left_woofer>, |
| 586 |
<&left_tweeter>, |
| 587 |
<&swr0 0>, |
| 588 |
<&lpass_wsamacro 0>, |
| 589 |
<&right_woofer>, |
| 590 |
<&right_tweeter>, |
| 591 |
<&swr3 0>, |
| 592 |
<&lpass_wsa2macro 0>; |
| 593 |
}; |
| 594 |
|
| 595 |
cpu { |
| 596 |
sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>; |
| 597 |
}; |
| 598 |
|
| 599 |
platform { |
| 600 |
sound-dai = <&q6apm>; |
| 601 |
}; |
| 602 |
}; |
| 603 |
|
| 604 |
va-dai-link { |
| 605 |
link-name = "VA Capture"; |
| 606 |
|
| 607 |
codec { |
| 608 |
sound-dai = <&lpass_vamacro 0>; |
| 609 |
}; |
| 610 |
|
| 611 |
cpu { |
| 612 |
sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>; |
| 613 |
}; |
| 614 |
|
| 615 |
platform { |
| 616 |
sound-dai = <&q6apm>; |
| 617 |
}; |
| 618 |
}; |
| 619 |
}; |
| 620 |
|
| 621 |
usb-1-ss0-sbu-mux { |
| 622 |
compatible = "onnn,fsusb42", "gpio-sbu-mux"; |
| 623 |
|
| 624 |
enable-gpios = <&tlmm 168 GPIO_ACTIVE_LOW>; |
| 625 |
select-gpios = <&tlmm 167 GPIO_ACTIVE_HIGH>; |
| 626 |
|
| 627 |
pinctrl-0 = <&usb_1_ss0_sbu_default>; |
| 628 |
pinctrl-names = "default"; |
| 629 |
|
| 630 |
mode-switch; |
| 631 |
orientation-switch; |
| 632 |
|
| 633 |
port { |
| 634 |
usb_1_ss0_sbu_mux: endpoint { |
| 635 |
remote-endpoint = <&pmic_glink_ss0_sbu>; |
| 636 |
}; |
| 637 |
}; |
| 638 |
}; |
| 639 |
|
| 640 |
wcn7850-pmu { |
| 641 |
compatible = "qcom,wcn7850-pmu"; |
| 642 |
|
| 643 |
vdd-supply = <&vreg_wcn_0p95>; |
| 644 |
vddio-supply = <&vreg_l15b_1p8>; |
| 645 |
vddaon-supply = <&vreg_wcn_0p95>; |
| 646 |
vdddig-supply = <&vreg_wcn_0p95>; |
| 647 |
vddrfa1p2-supply = <&vreg_wcn_1p9>; |
| 648 |
vddrfa1p8-supply = <&vreg_wcn_1p9>; |
| 649 |
|
| 650 |
bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>; |
| 651 |
wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>; |
| 652 |
|
| 653 |
pinctrl-0 = <&wcn_bt_en>, <&wcn_wlan_en>; |
| 654 |
pinctrl-names = "default"; |
| 655 |
|
| 656 |
regulators { |
| 657 |
vreg_pmu_rfa_cmn: ldo0 { |
| 658 |
regulator-name = "vreg_pmu_rfa_cmn"; |
| 659 |
}; |
| 660 |
|
| 661 |
vreg_pmu_aon_0p59: ldo1 { |
| 662 |
regulator-name = "vreg_pmu_aon_0p59"; |
| 663 |
}; |
| 664 |
|
| 665 |
vreg_pmu_wlcx_0p8: ldo2 { |
| 666 |
regulator-name = "vreg_pmu_wlcx_0p8"; |
| 667 |
}; |
| 668 |
|
| 669 |
vreg_pmu_wlmx_0p85: ldo3 { |
| 670 |
regulator-name = "vreg_pmu_wlmx_0p85"; |
| 671 |
}; |
| 672 |
|
| 673 |
vreg_pmu_btcmx_0p85: ldo4 { |
| 674 |
regulator-name = "vreg_pmu_btcmx_0p85"; |
| 675 |
}; |
| 676 |
|
| 677 |
vreg_pmu_rfa_0p8: ldo5 { |
| 678 |
regulator-name = "vreg_pmu_rfa_0p8"; |
| 679 |
}; |
| 680 |
|
| 681 |
vreg_pmu_rfa_1p2: ldo6 { |
| 682 |
regulator-name = "vreg_pmu_rfa_1p2"; |
| 683 |
}; |
| 684 |
|
| 685 |
vreg_pmu_rfa_1p8: ldo7 { |
| 686 |
regulator-name = "vreg_pmu_rfa_1p8"; |
| 687 |
}; |
| 688 |
|
| 689 |
vreg_pmu_pcie_0p9: ldo8 { |
| 690 |
regulator-name = "vreg_pmu_pcie_0p9"; |
| 691 |
}; |
| 692 |
|
| 693 |
vreg_pmu_pcie_1p8: ldo9 { |
| 694 |
regulator-name = "vreg_pmu_pcie_1p8"; |
| 695 |
}; |
| 696 |
}; |
| 697 |
}; |
| 698 |
}; |
| 699 |
|
| 700 |
&i2c1 { |
| 701 |
clock-frequency = <400000>; |
| 702 |
status = "okay"; |
| 703 |
|
| 704 |
typec-mux@8 { |
| 705 |
compatible = "parade,ps8830"; |
| 706 |
reg = <0x08>; |
| 707 |
|
| 708 |
clocks = <&rpmhcc RPMH_RF_CLK5>; |
| 709 |
|
| 710 |
vdd-supply = <&vreg_rtmr2_1p15>; |
| 711 |
vdd33-supply = <&vreg_rtmr2_3p3>; |
| 712 |
vdd33-cap-supply = <&vreg_rtmr2_3p3>; |
| 713 |
vddar-supply = <&vreg_rtmr2_1p15>; |
| 714 |
vddat-supply = <&vreg_rtmr2_1p15>; |
| 715 |
vddio-supply = <&vreg_rtmr2_1p8>; |
| 716 |
|
| 717 |
reset-gpios = <&tlmm 185 GPIO_ACTIVE_LOW>; |
| 718 |
|
| 719 |
pinctrl-0 = <&rtmr2_default>; |
| 720 |
pinctrl-names = "default"; |
| 721 |
|
| 722 |
orientation-switch; |
| 723 |
retimer-switch; |
| 724 |
|
| 725 |
ports { |
| 726 |
#address-cells = <1>; |
| 727 |
#size-cells = <0>; |
| 728 |
|
| 729 |
port@0 { |
| 730 |
reg = <0>; |
| 731 |
|
| 732 |
retimer_ss2_ss_out: endpoint { |
| 733 |
remote-endpoint = <&pmic_glink_ss2_ss_in>; |
| 734 |
}; |
| 735 |
}; |
| 736 |
|
| 737 |
port@1 { |
| 738 |
reg = <1>; |
| 739 |
|
| 740 |
retimer_ss2_ss_in: endpoint { |
| 741 |
remote-endpoint = <&usb_1_ss2_qmpphy_out>; |
| 742 |
}; |
| 743 |
}; |
| 744 |
|
| 745 |
port@2 { |
| 746 |
reg = <2>; |
| 747 |
|
| 748 |
retimer_ss2_con_sbu_out: endpoint { |
| 749 |
remote-endpoint = <&pmic_glink_ss2_con_sbu_in>; |
| 750 |
}; |
| 751 |
}; |
| 752 |
}; |
| 753 |
}; |
| 754 |
}; |
| 755 |
|
| 756 |
&i2c5 { |
| 757 |
clock-frequency = <400000>; |
| 758 |
|
| 759 |
status = "okay"; |
| 760 |
|
| 761 |
eusb3_repeater: redriver@47 { |
| 762 |
compatible = "nxp,ptn3222"; |
| 763 |
reg = <0x47>; |
| 764 |
#phy-cells = <0>; |
| 765 |
|
| 766 |
vdd3v3-supply = <&vreg_l13b_3p0>; |
| 767 |
vdd1v8-supply = <&vreg_l4b_1p8>; |
| 768 |
|
| 769 |
reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>; |
| 770 |
|
| 771 |
pinctrl-0 = <&eusb3_reset_n>; |
| 772 |
pinctrl-names = "default"; |
| 773 |
}; |
| 774 |
|
| 775 |
eusb5_repeater: redriver@43 { |
| 776 |
compatible = "nxp,ptn3222"; |
| 777 |
reg = <0x43>; |
| 778 |
#phy-cells = <0>; |
| 779 |
|
| 780 |
vdd3v3-supply = <&vreg_l13b_3p0>; |
| 781 |
vdd1v8-supply = <&vreg_l4b_1p8>; |
| 782 |
|
| 783 |
reset-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>; |
| 784 |
|
| 785 |
pinctrl-0 = <&eusb5_reset_n>; |
| 786 |
pinctrl-names = "default"; |
| 787 |
}; |
| 788 |
|
| 789 |
eusb6_repeater: redriver@4f { |
| 790 |
compatible = "nxp,ptn3222"; |
| 791 |
reg = <0x4f>; |
| 792 |
#phy-cells = <0>; |
| 793 |
|
| 794 |
vdd3v3-supply = <&vreg_l13b_3p0>; |
| 795 |
vdd1v8-supply = <&vreg_l4b_1p8>; |
| 796 |
|
| 797 |
reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>; |
| 798 |
|
| 799 |
pinctrl-0 = <&eusb6_reset_n>; |
| 800 |
pinctrl-names = "default"; |
| 801 |
}; |
| 802 |
}; |
| 803 |
|
| 804 |
&i2c7 { |
| 805 |
clock-frequency = <400000>; |
| 806 |
|
| 807 |
status = "okay"; |
| 808 |
|
| 809 |
typec-mux@8 { |
| 810 |
compatible = "parade,ps8830"; |
| 811 |
reg = <0x8>; |
| 812 |
|
| 813 |
clocks = <&rpmhcc RPMH_RF_CLK4>; |
| 814 |
|
| 815 |
vdd-supply = <&vreg_rtmr1_1p15>; |
| 816 |
vdd33-supply = <&vreg_rtmr1_3p3>; |
| 817 |
vdd33-cap-supply = <&vreg_rtmr1_3p3>; |
| 818 |
vddar-supply = <&vreg_rtmr1_1p15>; |
| 819 |
vddat-supply = <&vreg_rtmr1_1p15>; |
| 820 |
vddio-supply = <&vreg_rtmr1_1p8>; |
| 821 |
|
| 822 |
reset-gpios = <&tlmm 176 GPIO_ACTIVE_LOW>; |
| 823 |
|
| 824 |
pinctrl-0 = <&rtmr1_default>; |
| 825 |
pinctrl-names = "default"; |
| 826 |
|
| 827 |
retimer-switch; |
| 828 |
orientation-switch; |
| 829 |
|
| 830 |
ports { |
| 831 |
#address-cells = <1>; |
| 832 |
#size-cells = <0>; |
| 833 |
|
| 834 |
port@0 { |
| 835 |
reg = <0>; |
| 836 |
|
| 837 |
retimer_ss1_ss_out: endpoint { |
| 838 |
remote-endpoint = <&pmic_glink_ss1_ss_in>; |
| 839 |
}; |
| 840 |
}; |
| 841 |
|
| 842 |
port@1 { |
| 843 |
reg = <1>; |
| 844 |
|
| 845 |
retimer_ss1_ss_in: endpoint { |
| 846 |
remote-endpoint = <&usb_1_ss1_qmpphy_out>; |
| 847 |
}; |
| 848 |
}; |
| 849 |
|
| 850 |
port@2 { |
| 851 |
reg = <2>; |
| 852 |
|
| 853 |
retimer_ss1_con_sbu_out: endpoint { |
| 854 |
remote-endpoint = <&pmic_glink_ss1_con_sbu_in>; |
| 855 |
}; |
| 856 |
}; |
| 857 |
}; |
| 858 |
}; |
| 859 |
}; |
| 860 |
|
| 861 |
&lpass_tlmm { |
| 862 |
spkr_0_sd_n_active: spkr-0-sd-n-active-state { |
| 863 |
pins = "gpio12"; |
| 864 |
function = "gpio"; |
| 865 |
drive-strength = <16>; |
| 866 |
bias-disable; |
| 867 |
}; |
| 868 |
|
| 869 |
spkr_1_sd_n_active: spkr-1-sd-n-active-state { |
| 870 |
pins = "gpio13"; |
| 871 |
function = "gpio"; |
| 872 |
drive-strength = <16>; |
| 873 |
bias-disable; |
| 874 |
}; |
| 875 |
|
| 876 |
spkr_2_sd_n_active: spkr-2-sd-n-active-state { |
| 877 |
pins = "gpio17"; |
| 878 |
function = "gpio"; |
| 879 |
drive-strength = <16>; |
| 880 |
bias-disable; |
| 881 |
}; |
| 882 |
|
| 883 |
spkr_3_sd_n_active: spkr-3-sd-n-active-state { |
| 884 |
pins = "gpio18"; |
| 885 |
function = "gpio"; |
| 886 |
drive-strength = <16>; |
| 887 |
bias-disable; |
| 888 |
}; |
| 889 |
}; |
| 890 |
|
| 891 |
&lpass_vamacro { |
| 892 |
pinctrl-0 = <&dmic01_default>, <&dmic23_default>; |
| 893 |
pinctrl-names = "default"; |
| 894 |
|
| 895 |
vdd-micb-supply = <&vreg_l1b_1p8>; |
| 896 |
qcom,dmic-sample-rate = <4800000>; |
| 897 |
}; |
| 898 |
|
| 899 |
&mdss { |
| 900 |
status = "okay"; |
| 901 |
}; |
| 902 |
|
| 903 |
&mdss_dp0 { |
| 904 |
status = "okay"; |
| 905 |
}; |
| 906 |
|
| 907 |
&mdss_dp0_out { |
| 908 |
link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; |
| 909 |
}; |
| 910 |
|
| 911 |
&mdss_dp1 { |
| 912 |
status = "okay"; |
| 913 |
}; |
| 914 |
|
| 915 |
&mdss_dp1_out { |
| 916 |
link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; |
| 917 |
}; |
| 918 |
|
| 919 |
&mdss_dp2 { |
| 920 |
status = "okay"; |
| 921 |
}; |
| 922 |
|
| 923 |
&mdss_dp2_out { |
| 924 |
link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; |
| 925 |
}; |
| 926 |
|
| 927 |
&mdss_dp3 { |
| 928 |
/delete-property/ #sound-dai-cells; |
| 929 |
|
| 930 |
pinctrl-0 = <&edp0_hpd_default>; |
| 931 |
pinctrl-names = "default"; |
| 932 |
|
| 933 |
status = "okay"; |
| 934 |
|
| 935 |
aux-bus { |
| 936 |
panel { |
| 937 |
compatible = "edp-panel"; |
| 938 |
|
| 939 |
backlight = <&backlight>; |
| 940 |
power-supply = <&vreg_edp_3p3>; |
| 941 |
|
| 942 |
port { |
| 943 |
edp_panel_in: endpoint { |
| 944 |
remote-endpoint = <&mdss_dp3_out>; |
| 945 |
}; |
| 946 |
}; |
| 947 |
}; |
| 948 |
}; |
| 949 |
}; |
| 950 |
|
| 951 |
&mdss_dp3_out { |
| 952 |
data-lanes = <0 1 2 3>; |
| 953 |
link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>; |
| 954 |
|
| 955 |
remote-endpoint = <&edp_panel_in>; |
| 956 |
}; |
| 957 |
|
| 958 |
&mdss_dp3_phy { |
| 959 |
vdda-phy-supply = <&vreg_l3j_0p8>; |
| 960 |
vdda-pll-supply = <&vreg_l2j_1p2>; |
| 961 |
|
| 962 |
status = "okay"; |
| 963 |
}; |
| 964 |
|
| 965 |
&pcie3_port0 { |
| 966 |
vpcie12v-supply = <&vreg_pcie_12v>; |
| 967 |
vpcie3v3-supply = <&vreg_pcie_3v3>; |
| 968 |
vpcie3v3aux-supply = <&vreg_pcie_3v3_aux>; |
| 969 |
|
| 970 |
reset-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>; |
| 971 |
wake-gpios = <&tlmm 145 GPIO_ACTIVE_LOW>; |
| 972 |
}; |
| 973 |
|
| 974 |
&pcie4_port0 { |
| 975 |
reset-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>; |
| 976 |
wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>; |
| 977 |
|
| 978 |
wifi@0 { |
| 979 |
compatible = "pci17cb,1107"; |
| 980 |
reg = <0x10000 0x0 0x0 0x0 0x0>; |
| 981 |
|
| 982 |
vddaon-supply = <&vreg_pmu_aon_0p59>; |
| 983 |
vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; |
| 984 |
vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; |
| 985 |
vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; |
| 986 |
vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; |
| 987 |
vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; |
| 988 |
vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>; |
| 989 |
vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>; |
| 990 |
vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>; |
| 991 |
}; |
| 992 |
}; |
| 993 |
|
| 994 |
&pcie5 { |
| 995 |
vddpe-3v3-supply = <&vreg_wwan>; |
| 996 |
}; |
| 997 |
|
| 998 |
&pcie5_port0 { |
| 999 |
reset-gpios = <&tlmm 149 GPIO_ACTIVE_LOW>; |
| 1000 |
wake-gpios = <&tlmm 151 GPIO_ACTIVE_LOW>; |
| 1001 |
}; |
| 1002 |
|
| 1003 |
&pcie6a { |
| 1004 |
vddpe-3v3-supply = <&vreg_nvme>; |
| 1005 |
}; |
| 1006 |
|
| 1007 |
&pcie6a_port0 { |
| 1008 |
reset-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>; |
| 1009 |
wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>; |
| 1010 |
}; |
| 1011 |
|
| 1012 |
&pm8550_gpios { |
| 1013 |
rtmr0_default: rtmr0-reset-n-active-state { |
| 1014 |
pins = "gpio10"; |
| 1015 |
function = "normal"; |
| 1016 |
power-source = <1>; /* 1.8V */ |
| 1017 |
bias-disable; |
| 1018 |
input-disable; |
| 1019 |
output-enable; |
| 1020 |
}; |
| 1021 |
|
| 1022 |
usb0_3p3_reg_en: usb0-3p3-reg-en-state { |
| 1023 |
pins = "gpio11"; |
| 1024 |
function = "normal"; |
| 1025 |
power-source = <1>; /* 1.8V */ |
| 1026 |
bias-disable; |
| 1027 |
input-disable; |
| 1028 |
output-enable; |
| 1029 |
}; |
| 1030 |
}; |
| 1031 |
|
| 1032 |
&pm8550ve_8_gpios { |
| 1033 |
pcie_x8_12v: pcie-12v-default-state { |
| 1034 |
pins = "gpio8"; |
| 1035 |
function = "normal"; |
| 1036 |
output-enable; |
| 1037 |
output-high; |
| 1038 |
bias-pull-down; |
| 1039 |
power-source = <0>; |
| 1040 |
}; |
| 1041 |
}; |
| 1042 |
|
| 1043 |
&pm8550ve_9_gpios { |
| 1044 |
usb0_1p8_reg_en: usb0-1p8-reg-en-state { |
| 1045 |
pins = "gpio8"; |
| 1046 |
function = "normal"; |
| 1047 |
power-source = <1>; /* 1.8V */ |
| 1048 |
bias-disable; |
| 1049 |
input-disable; |
| 1050 |
output-enable; |
| 1051 |
}; |
| 1052 |
|
| 1053 |
usb3_en: usb3-en-state { |
| 1054 |
pins = "gpio4"; |
| 1055 |
function = "normal"; |
| 1056 |
qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>; |
| 1057 |
output-enable; |
| 1058 |
power-source = <0>; |
| 1059 |
}; |
| 1060 |
|
| 1061 |
usb6_en: usb6-en-state { |
| 1062 |
pins = "gpio5"; |
| 1063 |
function = "normal"; |
| 1064 |
qcom,drive-strength = <PMIC_GPIO_STRENGTH_HIGH>; |
| 1065 |
output-enable; |
| 1066 |
power-source = <0>; |
| 1067 |
}; |
| 1068 |
}; |
| 1069 |
|
| 1070 |
&pm8550_pwm { |
| 1071 |
status = "okay"; |
| 1072 |
|
| 1073 |
multi-led { |
| 1074 |
color = <LED_COLOR_ID_MULTI>; |
| 1075 |
function = LED_FUNCTION_STATUS; |
| 1076 |
|
| 1077 |
#address-cells = <1>; |
| 1078 |
#size-cells = <0>; |
| 1079 |
|
| 1080 |
led@1 { |
| 1081 |
reg = <1>; |
| 1082 |
color = <LED_COLOR_ID_RED>; |
| 1083 |
}; |
| 1084 |
|
| 1085 |
led@2 { |
| 1086 |
reg = <2>; |
| 1087 |
color = <LED_COLOR_ID_GREEN>; |
| 1088 |
}; |
| 1089 |
}; |
| 1090 |
}; |
| 1091 |
|
| 1092 |
&pmc8380_3_gpios { |
| 1093 |
edp_bl_en: edp-bl-en-state { |
| 1094 |
pins = "gpio4"; |
| 1095 |
function = "normal"; |
| 1096 |
power-source = <1>; |
| 1097 |
input-disable; |
| 1098 |
output-enable; |
| 1099 |
}; |
| 1100 |
|
| 1101 |
edp_bl_reg_en: edp-bl-reg-en-state { |
| 1102 |
pins = "gpio10"; |
| 1103 |
function = "normal"; |
| 1104 |
}; |
| 1105 |
}; |
| 1106 |
|
| 1107 |
&pmc8380_3_gpios { |
| 1108 |
pm_sde7_aux_3p3_en: pcie-aux-3p3-default-state { |
| 1109 |
pins = "gpio8"; |
| 1110 |
function = "normal"; |
| 1111 |
output-enable; |
| 1112 |
bias-pull-down; |
| 1113 |
power-source = <0>; |
| 1114 |
}; |
| 1115 |
|
| 1116 |
pm_sde7_main_3p3_en: pcie-main-3p3-default-state { |
| 1117 |
pins = "gpio6"; |
| 1118 |
function = "normal"; |
| 1119 |
output-enable; |
| 1120 |
bias-pull-down; |
| 1121 |
power-source = <0>; |
| 1122 |
}; |
| 1123 |
}; |
| 1124 |
|
| 1125 |
&pmc8380_5_gpios { |
| 1126 |
usb0_pwr_1p15_reg_en: usb0-pwr-1p15-reg-en-state { |
| 1127 |
pins = "gpio8"; |
| 1128 |
function = "normal"; |
| 1129 |
power-source = <1>; /* 1.8V */ |
| 1130 |
bias-disable; |
| 1131 |
input-disable; |
| 1132 |
output-enable; |
| 1133 |
}; |
| 1134 |
}; |
| 1135 |
|
| 1136 |
&pmk8550_gpios { |
| 1137 |
edp_bl_pwm: edp-bl-pwm-state { |
| 1138 |
pins = "gpio5"; |
| 1139 |
function = "func3"; |
| 1140 |
}; |
| 1141 |
}; |
| 1142 |
|
| 1143 |
&pmk8550_pwm { |
| 1144 |
status = "okay"; |
| 1145 |
}; |
| 1146 |
|
| 1147 |
&smb2360_0 { |
| 1148 |
status = "okay"; |
| 1149 |
}; |
| 1150 |
|
| 1151 |
&smb2360_0_eusb2_repeater { |
| 1152 |
vdd18-supply = <&vreg_l3d_1p8>; |
| 1153 |
vdd3-supply = <&vreg_l2b_3p0>; |
| 1154 |
}; |
| 1155 |
|
| 1156 |
&smb2360_1 { |
| 1157 |
status = "okay"; |
| 1158 |
}; |
| 1159 |
|
| 1160 |
&smb2360_1_eusb2_repeater { |
| 1161 |
vdd18-supply = <&vreg_l3d_1p8>; |
| 1162 |
vdd3-supply = <&vreg_l14b_3p0>; |
| 1163 |
}; |
| 1164 |
|
| 1165 |
&smb2360_2 { |
| 1166 |
status = "okay"; |
| 1167 |
}; |
| 1168 |
|
| 1169 |
&smb2360_2_eusb2_repeater { |
| 1170 |
vdd18-supply = <&vreg_l3d_1p8>; |
| 1171 |
vdd3-supply = <&vreg_l8b_3p0>; |
| 1172 |
}; |
| 1173 |
|
| 1174 |
&spi11 { |
| 1175 |
status = "okay"; |
| 1176 |
|
| 1177 |
tpm@0 { |
| 1178 |
compatible = "st,st33htpm-spi", "tcg,tpm_tis-spi"; |
| 1179 |
reg = <0>; |
| 1180 |
spi-max-frequency = <20000000>; |
| 1181 |
}; |
| 1182 |
}; |
| 1183 |
|
| 1184 |
&swr0 { |
| 1185 |
status = "okay"; |
| 1186 |
|
| 1187 |
pinctrl-0 = <&wsa_swr_active>; |
| 1188 |
pinctrl-names = "default"; |
| 1189 |
|
| 1190 |
/* WSA8845, Left Woofer */ |
| 1191 |
left_woofer: speaker@0,0 { |
| 1192 |
compatible = "sdw20217020400"; |
| 1193 |
pinctrl-0 = <&spkr_0_sd_n_active>; |
| 1194 |
pinctrl-names = "default"; |
| 1195 |
reg = <0 0>; |
| 1196 |
reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>; |
| 1197 |
#sound-dai-cells = <0>; |
| 1198 |
sound-name-prefix = "WooferLeft"; |
| 1199 |
vdd-1p8-supply = <&vreg_l15b_1p8>; |
| 1200 |
vdd-io-supply = <&vreg_l12b_1p2>; |
| 1201 |
qcom,port-mapping = <1 2 3 7 10 13>; |
| 1202 |
}; |
| 1203 |
|
| 1204 |
/* WSA8845, Left Tweeter */ |
| 1205 |
left_tweeter: speaker@0,1 { |
| 1206 |
compatible = "sdw20217020400"; |
| 1207 |
pinctrl-0 = <&spkr_1_sd_n_active>; |
| 1208 |
pinctrl-names = "default"; |
| 1209 |
reg = <0 1>; |
| 1210 |
reset-gpios = <&lpass_tlmm 13 GPIO_ACTIVE_LOW>; |
| 1211 |
#sound-dai-cells = <0>; |
| 1212 |
sound-name-prefix = "TweeterLeft"; |
| 1213 |
vdd-1p8-supply = <&vreg_l15b_1p8>; |
| 1214 |
vdd-io-supply = <&vreg_l12b_1p2>; |
| 1215 |
qcom,port-mapping = <4 5 6 7 11 13>; |
| 1216 |
}; |
| 1217 |
}; |
| 1218 |
|
| 1219 |
&swr1 { |
| 1220 |
status = "okay"; |
| 1221 |
|
| 1222 |
/* WCD9385 RX */ |
| 1223 |
wcd_rx: codec@0,4 { |
| 1224 |
compatible = "sdw20217010d00"; |
| 1225 |
reg = <0 4>; |
| 1226 |
qcom,rx-port-mapping = <1 2 3 4 5>; |
| 1227 |
}; |
| 1228 |
}; |
| 1229 |
|
| 1230 |
&swr2 { |
| 1231 |
status = "okay"; |
| 1232 |
|
| 1233 |
/* WCD9385 TX */ |
| 1234 |
wcd_tx: codec@0,3 { |
| 1235 |
compatible = "sdw20217010d00"; |
| 1236 |
reg = <0 3>; |
| 1237 |
qcom,tx-port-mapping = <2 2 3 4>; |
| 1238 |
}; |
| 1239 |
}; |
| 1240 |
|
| 1241 |
&swr3 { |
| 1242 |
status = "okay"; |
| 1243 |
|
| 1244 |
pinctrl-0 = <&wsa2_swr_active>; |
| 1245 |
pinctrl-names = "default"; |
| 1246 |
|
| 1247 |
/* WSA8845, Right Woofer */ |
| 1248 |
right_woofer: speaker@0,0 { |
| 1249 |
compatible = "sdw20217020400"; |
| 1250 |
pinctrl-0 = <&spkr_2_sd_n_active>; |
| 1251 |
pinctrl-names = "default"; |
| 1252 |
reg = <0 0>; |
| 1253 |
reset-gpios = <&lpass_tlmm 17 GPIO_ACTIVE_LOW>; |
| 1254 |
#sound-dai-cells = <0>; |
| 1255 |
sound-name-prefix = "WooferRight"; |
| 1256 |
vdd-1p8-supply = <&vreg_l15b_1p8>; |
| 1257 |
vdd-io-supply = <&vreg_l12b_1p2>; |
| 1258 |
qcom,port-mapping = <1 2 3 7 10 13>; |
| 1259 |
}; |
| 1260 |
|
| 1261 |
/* WSA8845, Right Tweeter */ |
| 1262 |
right_tweeter: speaker@0,1 { |
| 1263 |
compatible = "sdw20217020400"; |
| 1264 |
pinctrl-0 = <&spkr_3_sd_n_active>; |
| 1265 |
pinctrl-names = "default"; |
| 1266 |
reg = <0 1>; |
| 1267 |
reset-gpios = <&lpass_tlmm 18 GPIO_ACTIVE_LOW>; |
| 1268 |
#sound-dai-cells = <0>; |
| 1269 |
sound-name-prefix = "TweeterRight"; |
| 1270 |
vdd-1p8-supply = <&vreg_l15b_1p8>; |
| 1271 |
vdd-io-supply = <&vreg_l12b_1p2>; |
| 1272 |
qcom,port-mapping = <4 5 6 7 11 13>; |
| 1273 |
}; |
| 1274 |
}; |
| 1275 |
|
| 1276 |
&tlmm { |
| 1277 |
edp_reg_en: edp-reg-en-state { |
| 1278 |
pins = "gpio70"; |
| 1279 |
function = "gpio"; |
| 1280 |
drive-strength = <16>; |
| 1281 |
bias-disable; |
| 1282 |
}; |
| 1283 |
|
| 1284 |
eusb3_reset_n: eusb3-reset-n-state { |
| 1285 |
pins = "gpio6"; |
| 1286 |
function = "gpio"; |
| 1287 |
drive-strength = <2>; |
| 1288 |
bias-disable; |
| 1289 |
output-low; |
| 1290 |
}; |
| 1291 |
|
| 1292 |
eusb5_reset_n: eusb5-reset-n-state { |
| 1293 |
pins = "gpio7"; |
| 1294 |
function = "gpio"; |
| 1295 |
drive-strength = <2>; |
| 1296 |
bias-pull-up; |
| 1297 |
output-low; |
| 1298 |
}; |
| 1299 |
|
| 1300 |
eusb6_reset_n: eusb6-reset-n-state { |
| 1301 |
pins = "gpio184"; |
| 1302 |
function = "gpio"; |
| 1303 |
drive-strength = <2>; |
| 1304 |
bias-pull-up; |
| 1305 |
output-low; |
| 1306 |
}; |
| 1307 |
|
| 1308 |
nvme_reg_en: nvme-reg-en-state { |
| 1309 |
pins = "gpio18"; |
| 1310 |
function = "gpio"; |
| 1311 |
drive-strength = <2>; |
| 1312 |
bias-disable; |
| 1313 |
}; |
| 1314 |
|
| 1315 |
rtmr1_default: rtmr1-reset-n-active-state { |
| 1316 |
pins = "gpio176"; |
| 1317 |
function = "gpio"; |
| 1318 |
drive-strength = <2>; |
| 1319 |
bias-disable; |
| 1320 |
}; |
| 1321 |
|
| 1322 |
rtmr2_default: rtmr2-reset-n-active-state { |
| 1323 |
pins = "gpio185"; |
| 1324 |
function = "gpio"; |
| 1325 |
drive-strength = <2>; |
| 1326 |
bias-disable; |
| 1327 |
}; |
| 1328 |
|
| 1329 |
usb1_pwr_1p15_reg_en: usb1-pwr-1p15-reg-en-state { |
| 1330 |
pins = "gpio188"; |
| 1331 |
function = "gpio"; |
| 1332 |
drive-strength = <2>; |
| 1333 |
bias-disable; |
| 1334 |
}; |
| 1335 |
|
| 1336 |
usb1_pwr_1p8_reg_en: usb1-pwr-1p8-reg-en-state { |
| 1337 |
pins = "gpio175"; |
| 1338 |
function = "gpio"; |
| 1339 |
drive-strength = <2>; |
| 1340 |
bias-disable; |
| 1341 |
}; |
| 1342 |
|
| 1343 |
usb1_pwr_3p3_reg_en: usb1-pwr-3p3-reg-en-state { |
| 1344 |
pins = "gpio186"; |
| 1345 |
function = "gpio"; |
| 1346 |
drive-strength = <2>; |
| 1347 |
bias-disable; |
| 1348 |
}; |
| 1349 |
|
| 1350 |
usb2_pwr_1p15_reg_en: usb2-pwr-1p15-reg-en-state { |
| 1351 |
pins = "gpio189"; |
| 1352 |
function = "gpio"; |
| 1353 |
drive-strength = <2>; |
| 1354 |
bias-disable; |
| 1355 |
}; |
| 1356 |
|
| 1357 |
usb2_pwr_1p8_reg_en: usb2-pwr-1p8-reg-en-state { |
| 1358 |
pins = "gpio126"; |
| 1359 |
function = "gpio"; |
| 1360 |
drive-strength = <2>; |
| 1361 |
bias-disable; |
| 1362 |
}; |
| 1363 |
|
| 1364 |
usb2_pwr_3p3_reg_en: usb2-pwr-3p3-reg-en-state { |
| 1365 |
pins = "gpio187"; |
| 1366 |
function = "gpio"; |
| 1367 |
drive-strength = <2>; |
| 1368 |
bias-disable; |
| 1369 |
}; |
| 1370 |
|
| 1371 |
usb_1_ss0_sbu_default: usb-1-ss0-sbu-state { |
| 1372 |
mode-pins { |
| 1373 |
pins = "gpio166"; |
| 1374 |
function = "gpio"; |
| 1375 |
bias-disable; |
| 1376 |
drive-strength = <2>; |
| 1377 |
output-high; |
| 1378 |
}; |
| 1379 |
|
| 1380 |
oe-n-pins { |
| 1381 |
pins = "gpio168"; |
| 1382 |
function = "gpio"; |
| 1383 |
bias-disable; |
| 1384 |
drive-strength = <2>; |
| 1385 |
}; |
| 1386 |
|
| 1387 |
sel-pins { |
| 1388 |
pins = "gpio167"; |
| 1389 |
function = "gpio"; |
| 1390 |
bias-disable; |
| 1391 |
drive-strength = <2>; |
| 1392 |
}; |
| 1393 |
}; |
| 1394 |
|
| 1395 |
wcd_default: wcd-reset-n-active-state { |
| 1396 |
pins = "gpio191"; |
| 1397 |
function = "gpio"; |
| 1398 |
drive-strength = <16>; |
| 1399 |
bias-disable; |
| 1400 |
output-low; |
| 1401 |
}; |
| 1402 |
|
| 1403 |
wcn_bt_en: wcn-bt-en-state { |
| 1404 |
pins = "gpio116"; |
| 1405 |
function = "gpio"; |
| 1406 |
drive-strength = <2>; |
| 1407 |
bias-disable; |
| 1408 |
}; |
| 1409 |
|
| 1410 |
wcn_wlan_en: wcn-wlan-en-state { |
| 1411 |
pins = "gpio117"; |
| 1412 |
function = "gpio"; |
| 1413 |
drive-strength = <2>; |
| 1414 |
bias-disable; |
| 1415 |
}; |
| 1416 |
|
| 1417 |
wwan_sw_en: wwan-sw-en-state { |
| 1418 |
pins = "gpio221"; |
| 1419 |
function = "gpio"; |
| 1420 |
drive-strength = <4>; |
| 1421 |
bias-disable; |
| 1422 |
}; |
| 1423 |
|
| 1424 |
wcn_sw_en: wcn-sw-en-state { |
| 1425 |
pins = "gpio214"; |
| 1426 |
function = "gpio"; |
| 1427 |
drive-strength = <2>; |
| 1428 |
bias-disable; |
| 1429 |
}; |
| 1430 |
|
| 1431 |
/* Switches USB signal routing between the USB connector and the Wi-Fi card. */ |
| 1432 |
wcn_usb_sw_n: wcn-usb-sw-n-state { |
| 1433 |
pins = "gpio225"; |
| 1434 |
function = "gpio"; |
| 1435 |
drive-strength = <2>; |
| 1436 |
bias-disable; |
| 1437 |
output-high; |
| 1438 |
}; |
| 1439 |
}; |
| 1440 |
|
| 1441 |
&uart14 { |
| 1442 |
status = "okay"; |
| 1443 |
|
| 1444 |
bluetooth { |
| 1445 |
compatible = "qcom,wcn7850-bt"; |
| 1446 |
max-speed = <3200000>; |
| 1447 |
|
| 1448 |
vddaon-supply = <&vreg_pmu_aon_0p59>; |
| 1449 |
vddwlcx-supply = <&vreg_pmu_wlcx_0p8>; |
| 1450 |
vddwlmx-supply = <&vreg_pmu_wlmx_0p85>; |
| 1451 |
vddrfacmn-supply = <&vreg_pmu_rfa_cmn>; |
| 1452 |
vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>; |
| 1453 |
vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>; |
| 1454 |
vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>; |
| 1455 |
}; |
| 1456 |
}; |
| 1457 |
|
| 1458 |
&uart21 { |
| 1459 |
compatible = "qcom,geni-debug-uart"; |
| 1460 |
|
| 1461 |
status = "okay"; |
| 1462 |
}; |
| 1463 |
|
| 1464 |
&usb_1_ss0_dwc3_hs { |
| 1465 |
remote-endpoint = <&pmic_glink_ss0_hs_in>; |
| 1466 |
}; |
| 1467 |
|
| 1468 |
&usb_1_ss0_hsphy { |
| 1469 |
phys = <&smb2360_0_eusb2_repeater>; |
| 1470 |
}; |
| 1471 |
|
| 1472 |
&usb_1_ss0_qmpphy_out { |
| 1473 |
remote-endpoint = <&pmic_glink_ss0_ss_in>; |
| 1474 |
}; |
| 1475 |
|
| 1476 |
&usb_1_ss1_dwc3_hs { |
| 1477 |
remote-endpoint = <&pmic_glink_ss1_hs_in>; |
| 1478 |
}; |
| 1479 |
|
| 1480 |
&usb_1_ss1_hsphy { |
| 1481 |
phys = <&smb2360_1_eusb2_repeater>; |
| 1482 |
}; |
| 1483 |
|
| 1484 |
&usb_1_ss1_qmpphy_out { |
| 1485 |
remote-endpoint = <&retimer_ss1_ss_in>; |
| 1486 |
}; |
| 1487 |
|
| 1488 |
&usb_1_ss2_dwc3_hs { |
| 1489 |
remote-endpoint = <&pmic_glink_ss2_hs_in>; |
| 1490 |
}; |
| 1491 |
|
| 1492 |
&usb_1_ss2_hsphy { |
| 1493 |
phys = <&smb2360_2_eusb2_repeater>; |
| 1494 |
}; |
| 1495 |
|
| 1496 |
&usb_1_ss2_qmpphy_out { |
| 1497 |
remote-endpoint = <&retimer_ss2_ss_in>; |
| 1498 |
}; |
| 1499 |
|
| 1500 |
&usb_2_hsphy { |
| 1501 |
phys = <&eusb5_repeater>; |
| 1502 |
|
| 1503 |
pinctrl-0 = <&wcn_usb_sw_n>; |
| 1504 |
pinctrl-names = "default"; |
| 1505 |
}; |
| 1506 |
|
| 1507 |
&usb_mp_hsphy0 { |
| 1508 |
phys = <&eusb3_repeater>; |
| 1509 |
}; |
| 1510 |
|
| 1511 |
&usb_mp_hsphy1 { |
| 1512 |
phys = <&eusb6_repeater>; |
| 1513 |
}; |