Debian Codegraph @

scripts/dtc/include-prefixes/arm64/qcom/apq8039-t2.dts

raw
1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * Copyright (c) 2015, The Linux Foundation. All rights reserved.
4 * Copyright (c) 2020-2023, Linaro Ltd.
5 *
6 */
7
8 /dts-v1/;
9
10 #include "msm8939.dtsi"
11 #include "msm8939-pm8916.dtsi"
12 #include <dt-bindings/arm/qcom,ids.h>
13 #include <dt-bindings/gpio/gpio.h>
14 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
15 #include <dt-bindings/sound/apq8016-lpass.h>
16
17 / {
18 model = "Square, Inc. T2 Devkit";
19 compatible = "square,apq8039-t2", "qcom,msm8939";
20
21 qcom,board-id = <0x53 0x54>;
22 qcom,msm-id = <QCOM_ID_APQ8039 0x30000>;
23
24 aliases {
25 mmc0 = &sdhc_1;
26 mmc1 = &sdhc_2;
27 serial0 = &blsp_uart1;
28 serial1 = &blsp_uart2;
29 };
30
31 bl: backlight {
32 compatible = "gpio-backlight";
33 pinctrl-0 = <&pinctrl_backlight>;
34 pinctrl-names = "default";
35 gpios = <&tlmm 98 GPIO_ACTIVE_HIGH>;
36 };
37
38 chosen {
39 stdout-path = "serial1:115200n8";
40 };
41
42 vreg_lcd_avdd_reg: lcd-avdd-regulator {
43 compatible = "regulator-fixed";
44 regulator-name = "lcd_avdd";
45 regulator-min-microvolt = <5600000>;
46 regulator-max-microvolt = <5600000>;
47 pinctrl-0 = <&pinctrl_lcd_avdd_reg>;
48 pinctrl-names = "default";
49 gpio = <&tlmm 86 GPIO_ACTIVE_HIGH>;
50 startup-delay-us = <300>;
51 enable-active-high;
52 };
53
54 vreg_lcd_avee_reg: lcd-avee-regulator {
55 compatible = "regulator-fixed";
56 regulator-name = "lcd_avee";
57 regulator-min-microvolt = <5600000>;
58 regulator-max-microvolt = <5600000>;
59 pinctrl-0 = <&pinctrl_lcd_avee_reg>;
60 pinctrl-names = "default";
61 gpio = <&tlmm 87 GPIO_ACTIVE_HIGH>;
62 startup-delay-us = <300>;
63 enable-active-high;
64 };
65
66 vreg_lcd_iovcc_reg: lcd-iovcc-regulator {
67 compatible = "regulator-fixed";
68 regulator-name = "lcd_iovcc";
69 regulator-min-microvolt = <1800000>;
70 regulator-max-microvolt = <1800000>;
71 pinctrl-0 = <&pinctrl_lcd_iovcc_reg>;
72 pinctrl-names = "default";
73 gpio = <&tlmm 9 GPIO_ACTIVE_HIGH>;
74 startup-delay-us = <300>;
75 enable-active-high;
76 };
77 };
78
79 &blsp_i2c1 {
80 status = "okay";
81 };
82
83 &blsp_i2c2 {
84 status = "okay";
85 };
86
87 &blsp_i2c3 {
88 status = "okay";
89
90 typec_pd: usb-pd@38 {
91 compatible = "ti,tps6598x";
92 reg = <0x38>;
93
94 interrupt-parent = <&tlmm>;
95 interrupts = <107 IRQ_TYPE_LEVEL_LOW>;
96 interrupt-names = "irq";
97
98 pinctrl-names = "default";
99 pinctrl-0 = <&typec_irq>;
100
101 typec_con: connector {
102 compatible = "usb-c-connector";
103 label = "USB-C";
104
105 port {
106 typec_ep: endpoint {
107 remote-endpoint = <&otg_ep>;
108 };
109 };
110 };
111 };
112 };
113
114 &blsp_i2c5 {
115 status = "okay";
116 };
117
118 &blsp_uart1 {
119 pinctrl-0 = <&blsp_uart1_default>;
120 pinctrl-1 = <&blsp_uart1_sleep>;
121 pinctrl-names = "default", "sleep";
122 status = "okay";
123 };
124
125 &blsp_uart2 {
126 pinctrl-0 = <&blsp_uart2_console_default>;
127 pinctrl-1 = <&blsp_uart2_console_sleep>;
128 pinctrl-names = "default", "sleep";
129 status = "okay";
130 };
131
132 &gpu {
133 status = "okay";
134 };
135
136 &lpass {
137 status = "okay";
138 };
139
140 &lpass_codec {
141 status = "okay";
142 };
143
144 &mdss {
145 status = "okay";
146 };
147
148 &pm8916_codec {
149 qcom,hphl-jack-type-normally-open;
150 qcom,mbhc-vthreshold-low = <75 150 237 450 500>;
151 qcom,mbhc-vthreshold-high = <75 150 237 450 500>;
152 status = "okay";
153 };
154
155 &pm8916_gpios {
156 gpio-line-names =
157 "PM_GPIO1", /* WIFI_GPIO1_PRE */
158 "PM_GPIO2", /* WIFI_GPIO2_PRE */
159 "PM_GPIO3",
160 "PM_GPIO4";
161 };
162
163 &sdhc_1 {
164 status = "okay";
165 };
166
167 &sound {
168 model = "apq8039-square-sndcard";
169 audio-routing = "AMIC2", "MIC BIAS Internal2";
170 pinctrl-names = "default", "sleep";
171 pinctrl-0 = <&cdc_pdm_default>;
172 pinctrl-1 = <&cdc_pdm_sleep>;
173
174 internal-codec-playback-dai-link {
175 link-name = "WCD";
176 cpu {
177 sound-dai = <&lpass MI2S_PRIMARY>;
178 };
179 codec {
180 sound-dai = <&lpass_codec 0>, <&pm8916_codec 0>;
181 };
182 };
183
184 internal-codec-capture-dai-link {
185 link-name = "WCD-Capture";
186 cpu {
187 sound-dai = <&lpass MI2S_TERTIARY>;
188 };
189 codec {
190 sound-dai = <&lpass_codec 1>, <&pm8916_codec 1>;
191 };
192 };
193 };
194
195 /*
196 * Line names are taken from the schematic of T2, Ver X03.
197 * July 14, 2018. Page 4 in particular.
198 */
199 &tlmm {
200 gpio-line-names =
201 "APQ_UART1_TX", /* GPIO_0 */
202 "APQ_UART1_RX",
203 "APQ_I2C1_SDA",
204 "APQ_I2C1_SCL",
205 "APQ_UART2_TX_1V8",
206 "APQ_UART2_RX_1V8",
207 "APQ_I2C2_SDA",
208 "APQ_I2C2_SCL",
209 "NC",
210 "APQ_LCD_IOVCC_EN",
211 "APQ_I2C3_SDA", /* GPIO_10 */
212 "APQ_I2C3_SCL",
213 "TOUCH_RST_1V8_L",
214 "NC",
215 "APQ_I2C4_SDA",
216 "APQ_I2C4_SCL",
217 "APQ_ID5",
218 "USB_DISCONNECT",
219 "APQ_I2C5_SDA",
220 "APQ_I2C5_SCL",
221 "APQ_USBC_SPI_MOSI", /* GPIO_20 */
222 "APQ_USBC_SPI_MISO",
223 "APQ_USBC_SPI_SS_L",
224 "APQ_USBC_SPI_CLK",
225 "APQ_LCD_TE0",
226 "APQ_LCD_RST_L",
227 "NC",
228 "NC",
229 "ACCELEROMETER_INT1",
230 "APQ_CAM_I2C0_SDA",
231 "APQ_CAM_I2C0_SCL", /* GPIO_30 */
232 "ACCELEROMETER_INT2",
233 "NC",
234 "NC",
235 "NC",
236 "APQ_K21_RST_1V8_L",
237 "NC",
238 "APQ_EDL_1V8",
239 "TP145",
240 "BT_SSBI",
241 "NC", /* GPIO_40 */
242 "NC",
243 "NC",
244 "NC",
245 "NC",
246 "NC",
247 "NC",
248 "BT_CTRL",
249 "BT_DAT",
250 "PWR_GPIO_IN",
251 "PWR_GPIO_OUT", /* GPIO_50 */
252 "CARD_DET_MLB_L",
253 "HALL_SENSOR",
254 "TP63",
255 "TP64",
256 "TP65",
257 "NC",
258 "NC",
259 "NC",
260 "NC",
261 "NC", /* GPIO_60 */
262 "NC",
263 "APQ_K21_GPIO0_1V8",
264 "CDC_PDM_CLK",
265 "CDC_PDM_SYNC",
266 "CDC_PDM_TX",
267 "CDC_PDM_RX0",
268 "CDC_PDM_RX1",
269 "CDC_PDM_RX2",
270 "APQ_K21_GPIO1_1V8",
271 "NC", /* GPIO_70 */
272 "APQ_HUB_SEL_1V8",
273 "APQ_K21_GPIO2_1V8",
274 "APQ_K21_GPIO3_1V8",
275 "APQ_ID0",
276 "APQ_ID1",
277 "APQ_ID2",
278 "APQ_ID3",
279 "APQ_ID4",
280 "APQ_HUB_SUSP_IND",
281 "BOOT_CONFIG_0", /* GPIO_80 */
282 "BOOT_CONFIG_1",
283 "BOOT_CONFIG_2",
284 "BOOT_CONFIG_3",
285 "NC",
286 "NC",
287 "APQ_LCD_AVDD_EN",
288 "APQ_LCD_AVEE_EN",
289 "TP70",
290 "NC",
291 "APQ_DEBUG0", /* GPIO_90 */
292 "APQ_DEBUG1",
293 "APQ_DEBUG2",
294 "APQ_DEBUG3",
295 "TP165",
296 "NC",
297 "APQ_LNA_PWR_EN",
298 "NC",
299 "APQ_LCD_BL_EN",
300 "NC",
301 "APQ_LCD_ID0", /* GPIO_100 */
302 "APQ_LCD_ID1",
303 "USBC_GPIO5_1V8",
304 "NC",
305 "NC",
306 "NC",
307 "APQ_HUB_RST_1V8_L",
308 "USBC_I2C_IRQ_1V8_L",
309 "SPE_PWR_EN",
310 "NC",
311 "APQ_USB_ID", /* GPIO_110 */
312 "APQ_EXT_BUCK_VSEL",
313 "APQ_USB_ID_OUT",
314 "NC",
315 "PRNT_RST_L",
316 "APQ_CRQ_I2C_RDY_1V8",
317 "TYPEC_RST_1V8_H",
318 "CHG_BACKPWR_EN",
319 "CHG_PROCHOT_L",
320 "NC",
321 "USBC_GPIO7_1V8", /* GPIO_120 */
322 "NC";
323
324 blsp_uart1_default: blsp-uart1-default-state {
325 pins = "gpio0", "gpio1";
326 function = "blsp_uart1";
327 drive-strength = <16>;
328 bias-disable;
329 };
330
331 blsp_uart1_sleep: blsp-uart1-sleep-state {
332 pins = "gpio0", "gpio1";
333 function = "gpio";
334 drive-strength = <2>;
335 bias-pull-down;
336 };
337
338 pinctrl_backlight: backlight-state {
339 pins = "gpio98";
340 function = "gpio";
341 };
342
343 pinctrl_lcd_avdd_reg: lcd-avdd-reg-state {
344 pins = "gpio86";
345 function = "gpio";
346 };
347
348 pinctrl_lcd_avee_reg: lcd-avee-reg-state {
349 pins = "gpio87";
350 function = "gpio";
351 };
352
353 pinctrl_lcd_iovcc_reg: lcd-iovcc-reg-state {
354 pins = "gpio9";
355 function = "gpio";
356 };
357
358 pinctrl_lcd_rst: lcd-rst-state {
359 pins = "gpio25";
360 function = "gpio";
361 };
362
363 pinctrl_otg_default: otg-default-state {
364 function = "gpio";
365 pins = "gpio17";
366 output-high;
367 };
368
369 pinctrl_otg_device: otg-device-state {
370 function = "gpio";
371 pins = "gpio17";
372 output-low;
373 };
374
375 pinctrl_otg_host: otg-host-state {
376 function = "gpio";
377 pins = "gpio17";
378 output-low;
379 };
380
381 typec_irq: typec-irq-state {
382 function = "gpio";
383 pins = "gpio107";
384 bias-pull-up;
385 };
386 };
387
388 &usb {
389 pinctrl-names = "default", "host", "device";
390 pinctrl-0 = <&pinctrl_otg_default>;
391 pinctrl-1 = <&pinctrl_otg_host>;
392 pinctrl-2 = <&pinctrl_otg_device>;
393 usb-role-switch;
394 status = "okay";
395
396 port {
397 otg_ep: endpoint {
398 remote-endpoint = <&typec_ep>;
399 };
400 };
401 };
402
403 &wcnss {
404 status = "okay";
405 };
406
407 &wcnss_iris {
408 compatible = "qcom,wcn3680";
409 };
410
411 &wcnss_mem {
412 status = "okay";
413 };