Debian Codegraph @

scripts/dtc/include-prefixes/arm64/mediatek/mt8195-demo.dts

raw
1 // SPDX-License-Identifier: (GPL-2.0 OR MIT)
2 /*
3 * Copyright (C) 2022 BayLibre, SAS.
4 * Author: Fabien Parent <[email protected]>
5 */
6 /dts-v1/;
7
8 #include "mt8195.dtsi"
9 #include "mt6359.dtsi"
10
11 #include <dt-bindings/gpio/gpio.h>
12 #include <dt-bindings/input/input.h>
13 #include <dt-bindings/pinctrl/mt8195-pinfunc.h>
14 #include <dt-bindings/regulator/mediatek,mt6360-regulator.h>
15
16 / {
17 model = "MediaTek MT8195 demo board";
18 compatible = "mediatek,mt8195-demo", "mediatek,mt8195";
19
20 aliases {
21 serial0 = &uart0;
22 };
23
24 chosen {
25 stdout-path = "serial0:921600n8";
26 };
27
28 firmware {
29 optee {
30 compatible = "linaro,optee-tz";
31 method = "smc";
32 };
33 };
34
35 gpio-keys {
36 compatible = "gpio-keys";
37 pinctrl-names = "default";
38 pinctrl-0 = <&gpio_keys_pins>;
39
40 key-0 {
41 gpios = <&pio 106 GPIO_ACTIVE_LOW>;
42 label = "volume_up";
43 linux,code = <KEY_VOLUMEUP>;
44 wakeup-source;
45 debounce-interval = <15>;
46 };
47 };
48
49 memory@40000000 {
50 device_type = "memory";
51 reg = <0 0x40000000 0x2 0x00000000>;
52 };
53
54 reserved-memory {
55 #address-cells = <2>;
56 #size-cells = <2>;
57 ranges;
58
59 /*
60 * 12 MiB reserved for OP-TEE (BL32)
61 * +-----------------------+ 0x43e0_0000
62 * | SHMEM 2MiB |
63 * +-----------------------+ 0x43c0_0000
64 * | | TA_RAM 8MiB |
65 * + TZDRAM +--------------+ 0x4340_0000
66 * | | TEE_RAM 2MiB |
67 * +-----------------------+ 0x4320_0000
68 */
69 optee_reserved: optee@43200000 {
70 no-map;
71 reg = <0 0x43200000 0 0x00c00000>;
72 };
73
74 scp_mem: memory@50000000 {
75 compatible = "shared-dma-pool";
76 reg = <0 0x50000000 0 0x2900000>;
77 no-map;
78 };
79
80 vpu_mem: memory@53000000 {
81 compatible = "shared-dma-pool";
82 reg = <0 0x53000000 0 0x1400000>; /* 20 MB */
83 };
84
85 /* 2 MiB reserved for ARM Trusted Firmware (BL31) */
86 bl31_secmon_mem: memory@54600000 {
87 no-map;
88 reg = <0 0x54600000 0x0 0x200000>;
89 };
90
91 snd_dma_mem: memory@60000000 {
92 compatible = "shared-dma-pool";
93 reg = <0 0x60000000 0 0x1100000>;
94 no-map;
95 };
96
97 apu_mem: memory@62000000 {
98 compatible = "shared-dma-pool";
99 reg = <0 0x62000000 0 0x1400000>; /* 20 MB */
100 };
101 };
102 };
103
104 &eth {
105 phy-mode = "rgmii-id";
106 phy-handle = <&ethernet_phy0>;
107 snps,reset-gpio = <&pio 93 GPIO_ACTIVE_HIGH>;
108 snps,reset-delays-us = <0 10000 80000>;
109 pinctrl-names = "default", "sleep";
110 pinctrl-0 = <&eth_default_pins>;
111 pinctrl-1 = <&eth_sleep_pins>;
112 mediatek,mac-wol;
113 status = "okay";
114
115 mdio {
116 ethernet_phy0: ethernet-phy@1 {
117 reg = <0x1>;
118 };
119 };
120 };
121
122 &i2c6 {
123 clock-frequency = <400000>;
124 pinctrl-0 = <&i2c6_pins>;
125 pinctrl-names = "default";
126 status = "okay";
127
128 mt6360: pmic@34 {
129 compatible = "mediatek,mt6360";
130 reg = <0x34>;
131 interrupt-controller;
132 #interrupt-cells = <1>;
133 interrupts-extended = <&pio 101 IRQ_TYPE_EDGE_FALLING>;
134 interrupt-names = "IRQB";
135
136 charger {
137 compatible = "mediatek,mt6360-chg";
138 richtek,vinovp-microvolt = <14500000>;
139
140 otg_vbus_regulator: usb-otg-vbus-regulator {
141 regulator-name = "usb-otg-vbus";
142 regulator-min-microvolt = <4425000>;
143 regulator-max-microvolt = <5825000>;
144 };
145 };
146
147 regulator {
148 compatible = "mediatek,mt6360-regulator";
149 LDO_VIN3-supply = <&mt6360_buck2>;
150
151 mt6360_buck1: buck1 {
152 regulator-name = "mt6360,buck1";
153 regulator-min-microvolt = <300000>;
154 regulator-max-microvolt = <1300000>;
155 regulator-allowed-modes = <MT6360_OPMODE_NORMAL
156 MT6360_OPMODE_LP
157 MT6360_OPMODE_ULP>;
158 regulator-always-on;
159 };
160
161 mt6360_buck2: buck2 {
162 regulator-name = "mt6360,buck2";
163 regulator-min-microvolt = <300000>;
164 regulator-max-microvolt = <1300000>;
165 regulator-allowed-modes = <MT6360_OPMODE_NORMAL
166 MT6360_OPMODE_LP
167 MT6360_OPMODE_ULP>;
168 regulator-always-on;
169 };
170
171 mt6360_ldo1: ldo1 {
172 regulator-name = "mt6360,ldo1";
173 regulator-min-microvolt = <1200000>;
174 regulator-max-microvolt = <3600000>;
175 regulator-allowed-modes = <MT6360_OPMODE_NORMAL
176 MT6360_OPMODE_LP>;
177 };
178
179 mt6360_ldo2: ldo2 {
180 regulator-name = "mt6360,ldo2";
181 regulator-min-microvolt = <1200000>;
182 regulator-max-microvolt = <3600000>;
183 regulator-allowed-modes = <MT6360_OPMODE_NORMAL
184 MT6360_OPMODE_LP>;
185 };
186
187 mt6360_ldo3: ldo3 {
188 regulator-name = "mt6360,ldo3";
189 regulator-min-microvolt = <1200000>;
190 regulator-max-microvolt = <3600000>;
191 regulator-allowed-modes = <MT6360_OPMODE_NORMAL
192 MT6360_OPMODE_LP>;
193 };
194
195 mt6360_ldo5: ldo5 {
196 regulator-name = "mt6360,ldo5";
197 regulator-min-microvolt = <2700000>;
198 regulator-max-microvolt = <3600000>;
199 regulator-allowed-modes = <MT6360_OPMODE_NORMAL
200 MT6360_OPMODE_LP>;
201 };
202
203 mt6360_ldo6: ldo6 {
204 regulator-name = "mt6360,ldo6";
205 regulator-min-microvolt = <500000>;
206 regulator-max-microvolt = <2100000>;
207 regulator-allowed-modes = <MT6360_OPMODE_NORMAL
208 MT6360_OPMODE_LP>;
209 };
210
211 mt6360_ldo7: ldo7 {
212 regulator-name = "mt6360,ldo7";
213 regulator-min-microvolt = <500000>;
214 regulator-max-microvolt = <2100000>;
215 regulator-allowed-modes = <MT6360_OPMODE_NORMAL
216 MT6360_OPMODE_LP>;
217 regulator-always-on;
218 };
219 };
220 };
221 };
222
223 &mmc0 {
224 status = "okay";
225 pinctrl-names = "default", "state_uhs";
226 pinctrl-0 = <&mmc0_default_pins>;
227 pinctrl-1 = <&mmc0_uhs_pins>;
228 bus-width = <8>;
229 max-frequency = <200000000>;
230 cap-mmc-highspeed;
231 mmc-hs200-1_8v;
232 mmc-hs400-1_8v;
233 cap-mmc-hw-reset;
234 no-sdio;
235 no-sd;
236 hs400-ds-delay = <0x14c11>;
237 vmmc-supply = <&mt6359_vemc_1_ldo_reg>;
238 vqmmc-supply = <&mt6359_vufs_ldo_reg>;
239 non-removable;
240 };
241
242 &mmc1 {
243 pinctrl-names = "default", "state_uhs";
244 pinctrl-0 = <&mmc1_default_pins>;
245 pinctrl-1 = <&mmc1_uhs_pins>;
246 cd-gpios = <&pio 129 GPIO_ACTIVE_LOW>;
247 bus-width = <4>;
248 max-frequency = <200000000>;
249 cap-sd-highspeed;
250 sd-uhs-sdr50;
251 sd-uhs-sdr104;
252 vmmc-supply = <&mt6360_ldo5>;
253 vqmmc-supply = <&mt6360_ldo3>;
254 status = "okay";
255 };
256
257 &mt6359_vbbck_ldo_reg {
258 regulator-always-on;
259 };
260
261 &mt6359_vcore_buck_reg {
262 regulator-always-on;
263 };
264
265 &mt6359_vgpu11_buck_reg {
266 regulator-always-on;
267 };
268
269 &mt6359_vproc1_buck_reg {
270 regulator-always-on;
271 };
272
273 &mt6359_vproc2_buck_reg {
274 regulator-always-on;
275 };
276
277 &mt6359_vpu_buck_reg {
278 regulator-always-on;
279 };
280
281 &mt6359_vrf12_ldo_reg {
282 regulator-always-on;
283 };
284
285 &mt6359_vsram_md_ldo_reg {
286 regulator-always-on;
287 };
288
289 &mt6359_vsram_others_ldo_reg {
290 regulator-always-on;
291 };
292
293 &pio {
294 eth_default_pins: eth-default-pins {
295 pins-txd {
296 pinmux = <PINMUX_GPIO77__FUNC_GBE_TXD3>,
297 <PINMUX_GPIO78__FUNC_GBE_TXD2>,
298 <PINMUX_GPIO79__FUNC_GBE_TXD1>,
299 <PINMUX_GPIO80__FUNC_GBE_TXD0>;
300 drive-strength = <8>;
301 };
302 pins-cc {
303 pinmux = <PINMUX_GPIO85__FUNC_GBE_TXC>,
304 <PINMUX_GPIO88__FUNC_GBE_TXEN>,
305 <PINMUX_GPIO87__FUNC_GBE_RXDV>,
306 <PINMUX_GPIO86__FUNC_GBE_RXC>;
307 drive-strength = <8>;
308 };
309 pins-rxd {
310 pinmux = <PINMUX_GPIO81__FUNC_GBE_RXD3>,
311 <PINMUX_GPIO82__FUNC_GBE_RXD2>,
312 <PINMUX_GPIO83__FUNC_GBE_RXD1>,
313 <PINMUX_GPIO84__FUNC_GBE_RXD0>;
314 };
315 pins-mdio {
316 pinmux = <PINMUX_GPIO89__FUNC_GBE_MDC>,
317 <PINMUX_GPIO90__FUNC_GBE_MDIO>;
318 input-enable;
319 };
320 pins-power {
321 pinmux = <PINMUX_GPIO91__FUNC_GPIO91>,
322 <PINMUX_GPIO92__FUNC_GPIO92>;
323 output-high;
324 };
325 };
326
327 eth_sleep_pins: eth-sleep-pins {
328 pins-txd {
329 pinmux = <PINMUX_GPIO77__FUNC_GPIO77>,
330 <PINMUX_GPIO78__FUNC_GPIO78>,
331 <PINMUX_GPIO79__FUNC_GPIO79>,
332 <PINMUX_GPIO80__FUNC_GPIO80>;
333 };
334 pins-cc {
335 pinmux = <PINMUX_GPIO85__FUNC_GPIO85>,
336 <PINMUX_GPIO88__FUNC_GPIO88>,
337 <PINMUX_GPIO87__FUNC_GPIO87>,
338 <PINMUX_GPIO86__FUNC_GPIO86>;
339 };
340 pins-rxd {
341 pinmux = <PINMUX_GPIO81__FUNC_GPIO81>,
342 <PINMUX_GPIO82__FUNC_GPIO82>,
343 <PINMUX_GPIO83__FUNC_GPIO83>,
344 <PINMUX_GPIO84__FUNC_GPIO84>;
345 };
346 pins-mdio {
347 pinmux = <PINMUX_GPIO89__FUNC_GPIO89>,
348 <PINMUX_GPIO90__FUNC_GPIO90>;
349 input-disable;
350 bias-disable;
351 };
352 };
353
354 gpio_keys_pins: gpio-keys-pins {
355 pins {
356 pinmux = <PINMUX_GPIO106__FUNC_GPIO106>;
357 input-enable;
358 };
359 };
360
361 i2c6_pins: i2c6-pins {
362 pins {
363 pinmux = <PINMUX_GPIO25__FUNC_SDA6>,
364 <PINMUX_GPIO26__FUNC_SCL6>;
365 bias-pull-up;
366 };
367 };
368
369 mmc0_default_pins: mmc0-default-pins {
370 pins-clk {
371 pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
372 drive-strength = <6>;
373 bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
374 };
375
376 pins-cmd-dat {
377 pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
378 <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
379 <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
380 <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
381 <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
382 <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
383 <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
384 <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
385 <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
386 input-enable;
387 drive-strength = <6>;
388 bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
389 };
390
391 pins-rst {
392 pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
393 drive-strength = <6>;
394 bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
395 };
396 };
397
398 mmc0_uhs_pins: mmc0-uhs-pins {
399 pins-clk {
400 pinmux = <PINMUX_GPIO122__FUNC_MSDC0_CLK>;
401 drive-strength = <8>;
402 bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
403 };
404
405 pins-cmd-dat {
406 pinmux = <PINMUX_GPIO126__FUNC_MSDC0_DAT0>,
407 <PINMUX_GPIO125__FUNC_MSDC0_DAT1>,
408 <PINMUX_GPIO124__FUNC_MSDC0_DAT2>,
409 <PINMUX_GPIO123__FUNC_MSDC0_DAT3>,
410 <PINMUX_GPIO119__FUNC_MSDC0_DAT4>,
411 <PINMUX_GPIO118__FUNC_MSDC0_DAT5>,
412 <PINMUX_GPIO117__FUNC_MSDC0_DAT6>,
413 <PINMUX_GPIO116__FUNC_MSDC0_DAT7>,
414 <PINMUX_GPIO121__FUNC_MSDC0_CMD>;
415 input-enable;
416 drive-strength = <8>;
417 bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
418 };
419
420 pins-ds {
421 pinmux = <PINMUX_GPIO127__FUNC_MSDC0_DSL>;
422 drive-strength = <8>;
423 bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
424 };
425
426 pins-rst {
427 pinmux = <PINMUX_GPIO120__FUNC_MSDC0_RSTB>;
428 drive-strength = <8>;
429 bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
430 };
431 };
432
433 mmc1_default_pins: mmc1-default-pins {
434 pins-clk {
435 pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
436 drive-strength = <8>;
437 bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
438 };
439
440 pins-cmd-dat {
441 pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
442 <PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
443 <PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
444 <PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
445 <PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
446 input-enable;
447 drive-strength = <8>;
448 bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
449 };
450
451 pins-insert {
452 pinmux = <PINMUX_GPIO129__FUNC_GPIO129>;
453 bias-pull-up;
454 };
455 };
456
457 mmc1_uhs_pins: mmc1-uhs-pins {
458 pins-clk {
459 pinmux = <PINMUX_GPIO111__FUNC_MSDC1_CLK>;
460 drive-strength = <8>;
461 bias-pull-down = <MTK_PUPD_SET_R1R0_10>;
462 };
463
464 pins-cmd-dat {
465 pinmux = <PINMUX_GPIO110__FUNC_MSDC1_CMD>,
466 <PINMUX_GPIO112__FUNC_MSDC1_DAT0>,
467 <PINMUX_GPIO113__FUNC_MSDC1_DAT1>,
468 <PINMUX_GPIO114__FUNC_MSDC1_DAT2>,
469 <PINMUX_GPIO115__FUNC_MSDC1_DAT3>;
470 input-enable;
471 drive-strength = <8>;
472 bias-pull-up = <MTK_PUPD_SET_R1R0_01>;
473 };
474 };
475
476 uart0_pins: uart0-pins {
477 pins {
478 pinmux = <PINMUX_GPIO98__FUNC_UTXD0>,
479 <PINMUX_GPIO99__FUNC_URXD0>;
480 };
481 };
482
483 uart1_pins: uart1-pins {
484 pins {
485 pinmux = <PINMUX_GPIO102__FUNC_UTXD1>,
486 <PINMUX_GPIO103__FUNC_URXD1>;
487 };
488 };
489 };
490
491
492 &pmic {
493 interrupts-extended = <&pio 222 IRQ_TYPE_LEVEL_HIGH>;
494 };
495
496 &uart0 {
497 pinctrl-names = "default";
498 pinctrl-0 = <&uart0_pins>;
499 status = "okay";
500 };
501
502 &uart1 {
503 pinctrl-names = "default";
504 pinctrl-0 = <&uart1_pins>;
505 status = "okay";
506 };
507
508 &u3phy0 {
509 status = "okay";
510 };
511
512 &u3phy1 {
513 status = "okay";
514 };
515
516 &u3phy2 {
517 status = "okay";
518 };
519
520 &u3phy3 {
521 status = "okay";
522 };
523
524 &ssusb0 {
525 vusb33-supply = <&mt6359_vusb_ldo_reg>;
526 status = "okay";
527 };
528
529 &ssusb2 {
530 vusb33-supply = <&mt6359_vusb_ldo_reg>;
531 status = "okay";
532 };
533
534 &ssusb3 {
535 vusb33-supply = <&mt6359_vusb_ldo_reg>;
536 status = "okay";
537 };
538
539 &xhci0 {
540 vbus-supply = <&otg_vbus_regulator>;
541 status = "okay";
542 };
543
544 &xhci1 {
545 vusb33-supply = <&mt6359_vusb_ldo_reg>;
546 status = "okay";
547 };
548
549 &xhci2 {
550 status = "okay";
551 };
552
553 &xhci3 {
554 status = "okay";
555 };