| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* Copyright 2016 MediaTek Inc. |
| 4 |
*/ |
| 5 |
|
| 6 |
#include "mt8173-elm.dtsi" |
| 7 |
|
| 8 |
&hdmi_mux_pins { |
| 9 |
pins-mux { |
| 10 |
pinmux = <MT8173_PIN_98_URTS1__FUNC_GPIO98>; |
| 11 |
bias-pull-up; |
| 12 |
output-high; |
| 13 |
}; |
| 14 |
}; |
| 15 |
|
| 16 |
&i2c0 { |
| 17 |
clock-frequency = <200000>; |
| 18 |
}; |
| 19 |
|
| 20 |
&i2c3 { |
| 21 |
touchscreen2: touchscreen@34 { |
| 22 |
compatible = "melfas,mip4_ts"; |
| 23 |
reg = <0x34>; |
| 24 |
interrupts-extended = <&pio 88 IRQ_TYPE_LEVEL_LOW>; |
| 25 |
status = "fail-needs-probe"; |
| 26 |
}; |
| 27 |
|
| 28 |
/* |
| 29 |
* Lenovo 100e Chromebook 2nd Gen (MTK) and Lenovo 300e Chromebook 2nd |
| 30 |
* Gen (MTK) are using synaptics touchscreen (hid-over-i2c driver) as a |
| 31 |
* second source touchscreen. |
| 32 |
*/ |
| 33 |
touchscreen3: touchscreen@20 { |
| 34 |
compatible = "hid-over-i2c"; |
| 35 |
reg = <0x20>; |
| 36 |
hid-descr-addr = <0x0020>; |
| 37 |
interrupts-extended = <&pio 88 IRQ_TYPE_LEVEL_LOW>; |
| 38 |
status = "fail-needs-probe"; |
| 39 |
}; |
| 40 |
|
| 41 |
/* Lenovo Ideapad C330 uses G2Touch touchscreen as a 2nd source touchscreen */ |
| 42 |
touchscreen@40 { |
| 43 |
compatible = "hid-over-i2c"; |
| 44 |
reg = <0x40>; |
| 45 |
hid-descr-addr = <0x0001>; |
| 46 |
interrupt-parent = <&pio>; |
| 47 |
interrupts = <88 IRQ_TYPE_LEVEL_LOW>; |
| 48 |
status = "fail-needs-probe"; |
| 49 |
}; |
| 50 |
}; |
| 51 |
|
| 52 |
&i2c4 { |
| 53 |
/* |
| 54 |
* Lenovo 100e Chromebook 2nd Gen (MTK) and Lenovo 300e Chromebook 2nd |
| 55 |
* Gen (MTK) are using synaptics trackpad (hid-over-i2c driver) as a |
| 56 |
* second source trackpad. |
| 57 |
*/ |
| 58 |
trackpad2: trackpad@2c { |
| 59 |
compatible = "hid-over-i2c"; |
| 60 |
interrupts-extended = <&pio 117 IRQ_TYPE_LEVEL_LOW>; |
| 61 |
pinctrl-names = "default"; |
| 62 |
pinctrl-0 = <&trackpad_irq>; |
| 63 |
reg = <0x2c>; |
| 64 |
hid-descr-addr = <0x0020>; |
| 65 |
/* |
| 66 |
* The trackpad needs a post-power-on delay of 100ms, |
| 67 |
* but at time of writing, the power supply for it on |
| 68 |
* this board is always on. The delay is therefore not |
| 69 |
* added to avoid impacting the readiness of the |
| 70 |
* trackpad. |
| 71 |
*/ |
| 72 |
vdd-supply = <&mt6397_vgp6_reg>; |
| 73 |
wakeup-source; |
| 74 |
status = "fail-needs-probe"; |
| 75 |
}; |
| 76 |
}; |
| 77 |
|
| 78 |
&mmc1_pins_default { |
| 79 |
pins-wp { |
| 80 |
pinmux = <MT8173_PIN_42_DSI_TE__FUNC_GPIO42>; |
| 81 |
input-enable; |
| 82 |
bias-pull-up; |
| 83 |
}; |
| 84 |
}; |
| 85 |
|
| 86 |
&mmc1 { |
| 87 |
wp-gpios = <&pio 42 GPIO_ACTIVE_HIGH>; |
| 88 |
}; |
| 89 |
|
| 90 |
&touchscreen { |
| 91 |
status = "fail-needs-probe"; |
| 92 |
}; |
| 93 |
|
| 94 |
&trackpad { |
| 95 |
status = "fail-needs-probe"; |
| 96 |
}; |