| 1 |
// SPDX-License-Identifier: (GPL-2.0 OR MIT) |
| 2 |
/* |
| 3 |
* Copyright (C) 2021 MediaTek Inc. |
| 4 |
* Author: Sam.Shih <[email protected]> |
| 5 |
*/ |
| 6 |
|
| 7 |
/dts-v1/; |
| 8 |
#include <dt-bindings/pinctrl/mt65xx.h> |
| 9 |
|
| 10 |
#include "mt7986a.dtsi" |
| 11 |
|
| 12 |
/ { |
| 13 |
model = "MediaTek MT7986a RFB"; |
| 14 |
chassis-type = "embedded"; |
| 15 |
compatible = "mediatek,mt7986a-rfb", "mediatek,mt7986a"; |
| 16 |
|
| 17 |
aliases { |
| 18 |
serial0 = &uart0; |
| 19 |
}; |
| 20 |
|
| 21 |
chosen { |
| 22 |
stdout-path = "serial0:115200n8"; |
| 23 |
}; |
| 24 |
|
| 25 |
memory@40000000 { |
| 26 |
device_type = "memory"; |
| 27 |
reg = <0 0x40000000 0 0x40000000>; |
| 28 |
}; |
| 29 |
|
| 30 |
reg_1p8v: regulator-1p8v { |
| 31 |
compatible = "regulator-fixed"; |
| 32 |
regulator-name = "fixed-1.8V"; |
| 33 |
regulator-min-microvolt = <1800000>; |
| 34 |
regulator-max-microvolt = <1800000>; |
| 35 |
regulator-boot-on; |
| 36 |
regulator-always-on; |
| 37 |
}; |
| 38 |
|
| 39 |
reg_3p3v: regulator-3p3v { |
| 40 |
compatible = "regulator-fixed"; |
| 41 |
regulator-name = "fixed-3.3V"; |
| 42 |
regulator-min-microvolt = <3300000>; |
| 43 |
regulator-max-microvolt = <3300000>; |
| 44 |
regulator-boot-on; |
| 45 |
regulator-always-on; |
| 46 |
}; |
| 47 |
}; |
| 48 |
|
| 49 |
&crypto { |
| 50 |
status = "okay"; |
| 51 |
}; |
| 52 |
|
| 53 |
ð { |
| 54 |
status = "okay"; |
| 55 |
|
| 56 |
gmac0: mac@0 { |
| 57 |
compatible = "mediatek,eth-mac"; |
| 58 |
reg = <0>; |
| 59 |
phy-mode = "2500base-x"; |
| 60 |
|
| 61 |
fixed-link { |
| 62 |
speed = <2500>; |
| 63 |
full-duplex; |
| 64 |
pause; |
| 65 |
}; |
| 66 |
}; |
| 67 |
|
| 68 |
gmac1: mac@1 { |
| 69 |
compatible = "mediatek,eth-mac"; |
| 70 |
reg = <1>; |
| 71 |
phy-mode = "rgmii"; |
| 72 |
|
| 73 |
fixed-link { |
| 74 |
speed = <1000>; |
| 75 |
full-duplex; |
| 76 |
pause; |
| 77 |
}; |
| 78 |
}; |
| 79 |
|
| 80 |
mdio: mdio-bus { |
| 81 |
#address-cells = <1>; |
| 82 |
#size-cells = <0>; |
| 83 |
}; |
| 84 |
}; |
| 85 |
|
| 86 |
&mdio { |
| 87 |
switch: switch@0 { |
| 88 |
compatible = "mediatek,mt7531"; |
| 89 |
reg = <31>; |
| 90 |
reset-gpios = <&pio 5 0>; |
| 91 |
}; |
| 92 |
}; |
| 93 |
|
| 94 |
&mmc0 { |
| 95 |
pinctrl-names = "default", "state_uhs"; |
| 96 |
pinctrl-0 = <&mmc0_pins_default>; |
| 97 |
pinctrl-1 = <&mmc0_pins_uhs>; |
| 98 |
bus-width = <8>; |
| 99 |
max-frequency = <200000000>; |
| 100 |
cap-mmc-highspeed; |
| 101 |
mmc-hs200-1_8v; |
| 102 |
mmc-hs400-1_8v; |
| 103 |
hs400-ds-delay = <0x14014>; |
| 104 |
vmmc-supply = <®_3p3v>; |
| 105 |
vqmmc-supply = <®_1p8v>; |
| 106 |
non-removable; |
| 107 |
no-sd; |
| 108 |
no-sdio; |
| 109 |
}; |
| 110 |
|
| 111 |
&pcie { |
| 112 |
pinctrl-names = "default"; |
| 113 |
pinctrl-0 = <&pcie_pins>; |
| 114 |
status = "okay"; |
| 115 |
}; |
| 116 |
|
| 117 |
&pcie_phy { |
| 118 |
status = "okay"; |
| 119 |
}; |
| 120 |
|
| 121 |
&pio { |
| 122 |
mmc0_pins_default: mmc0-pins { |
| 123 |
mux { |
| 124 |
function = "emmc"; |
| 125 |
groups = "emmc_51"; |
| 126 |
}; |
| 127 |
conf-cmd-dat { |
| 128 |
pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", |
| 129 |
"EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", |
| 130 |
"EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; |
| 131 |
input-enable; |
| 132 |
drive-strength = <4>; |
| 133 |
bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ |
| 134 |
}; |
| 135 |
conf-clk { |
| 136 |
pins = "EMMC_CK"; |
| 137 |
drive-strength = <6>; |
| 138 |
bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ |
| 139 |
}; |
| 140 |
conf-ds { |
| 141 |
pins = "EMMC_DSL"; |
| 142 |
bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ |
| 143 |
}; |
| 144 |
conf-rst { |
| 145 |
pins = "EMMC_RSTB"; |
| 146 |
drive-strength = <4>; |
| 147 |
bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ |
| 148 |
}; |
| 149 |
}; |
| 150 |
|
| 151 |
mmc0_pins_uhs: mmc0-uhs-pins { |
| 152 |
mux { |
| 153 |
function = "emmc"; |
| 154 |
groups = "emmc_51"; |
| 155 |
}; |
| 156 |
conf-cmd-dat { |
| 157 |
pins = "EMMC_DATA_0", "EMMC_DATA_1", "EMMC_DATA_2", |
| 158 |
"EMMC_DATA_3", "EMMC_DATA_4", "EMMC_DATA_5", |
| 159 |
"EMMC_DATA_6", "EMMC_DATA_7", "EMMC_CMD"; |
| 160 |
input-enable; |
| 161 |
drive-strength = <4>; |
| 162 |
bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ |
| 163 |
}; |
| 164 |
conf-clk { |
| 165 |
pins = "EMMC_CK"; |
| 166 |
drive-strength = <6>; |
| 167 |
bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ |
| 168 |
}; |
| 169 |
conf-ds { |
| 170 |
pins = "EMMC_DSL"; |
| 171 |
bias-pull-down = <MTK_PUPD_SET_R1R0_10>; /* pull-down 50K */ |
| 172 |
}; |
| 173 |
conf-rst { |
| 174 |
pins = "EMMC_RSTB"; |
| 175 |
drive-strength = <4>; |
| 176 |
bias-pull-up = <MTK_PUPD_SET_R1R0_01>; /* pull-up 10K */ |
| 177 |
}; |
| 178 |
}; |
| 179 |
|
| 180 |
pcie_pins: pcie-pins { |
| 181 |
mux { |
| 182 |
function = "pcie"; |
| 183 |
groups = "pcie_clk", "pcie_wake", "pcie_pereset"; |
| 184 |
}; |
| 185 |
}; |
| 186 |
|
| 187 |
spi_flash_pins: spi-flash-pins { |
| 188 |
mux { |
| 189 |
function = "spi"; |
| 190 |
groups = "spi0", "spi0_wp_hold"; |
| 191 |
}; |
| 192 |
}; |
| 193 |
|
| 194 |
spic_pins: spic-pins { |
| 195 |
mux { |
| 196 |
function = "spi"; |
| 197 |
groups = "spi1_2"; |
| 198 |
}; |
| 199 |
}; |
| 200 |
|
| 201 |
uart1_pins: uart1-pins { |
| 202 |
mux { |
| 203 |
function = "uart"; |
| 204 |
groups = "uart1"; |
| 205 |
}; |
| 206 |
}; |
| 207 |
|
| 208 |
uart2_pins: uart2-pins { |
| 209 |
mux { |
| 210 |
function = "uart"; |
| 211 |
groups = "uart2"; |
| 212 |
}; |
| 213 |
}; |
| 214 |
|
| 215 |
wf_2g_5g_pins: wf-2g-5g-pins { |
| 216 |
mux { |
| 217 |
function = "wifi"; |
| 218 |
groups = "wf_2g", "wf_5g"; |
| 219 |
}; |
| 220 |
conf { |
| 221 |
pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", |
| 222 |
"WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", |
| 223 |
"WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", |
| 224 |
"WF0_TOP_CLK", "WF0_TOP_DATA", "WF1_HB1", |
| 225 |
"WF1_HB2", "WF1_HB3", "WF1_HB4", "WF1_HB0", |
| 226 |
"WF1_HB5", "WF1_HB6", "WF1_HB7", "WF1_HB8", |
| 227 |
"WF1_TOP_CLK", "WF1_TOP_DATA"; |
| 228 |
drive-strength = <4>; |
| 229 |
}; |
| 230 |
}; |
| 231 |
|
| 232 |
wf_dbdc_pins: wf-dbdc-pins { |
| 233 |
mux { |
| 234 |
function = "wifi"; |
| 235 |
groups = "wf_dbdc"; |
| 236 |
}; |
| 237 |
conf { |
| 238 |
pins = "WF0_HB1", "WF0_HB2", "WF0_HB3", "WF0_HB4", |
| 239 |
"WF0_HB0", "WF0_HB0_B", "WF0_HB5", "WF0_HB6", |
| 240 |
"WF0_HB7", "WF0_HB8", "WF0_HB9", "WF0_HB10", |
| 241 |
"WF0_TOP_CLK", "WF0_TOP_DATA"; |
| 242 |
drive-strength = <4>; |
| 243 |
}; |
| 244 |
}; |
| 245 |
}; |
| 246 |
|
| 247 |
&spi0 { |
| 248 |
pinctrl-names = "default"; |
| 249 |
pinctrl-0 = <&spi_flash_pins>; |
| 250 |
cs-gpios = <0>, <0>; |
| 251 |
status = "okay"; |
| 252 |
|
| 253 |
spi_nand: flash@0 { |
| 254 |
compatible = "spi-nand"; |
| 255 |
reg = <0>; |
| 256 |
spi-max-frequency = <10000000>; |
| 257 |
spi-tx-bus-width = <4>; |
| 258 |
spi-rx-bus-width = <4>; |
| 259 |
}; |
| 260 |
}; |
| 261 |
|
| 262 |
&spi1 { |
| 263 |
pinctrl-names = "default"; |
| 264 |
pinctrl-0 = <&spic_pins>; |
| 265 |
cs-gpios = <0>, <0>; |
| 266 |
status = "okay"; |
| 267 |
}; |
| 268 |
|
| 269 |
&ssusb { |
| 270 |
status = "okay"; |
| 271 |
}; |
| 272 |
|
| 273 |
&switch { |
| 274 |
ports { |
| 275 |
#address-cells = <1>; |
| 276 |
#size-cells = <0>; |
| 277 |
|
| 278 |
port@0 { |
| 279 |
reg = <0>; |
| 280 |
label = "lan0"; |
| 281 |
}; |
| 282 |
|
| 283 |
port@1 { |
| 284 |
reg = <1>; |
| 285 |
label = "lan1"; |
| 286 |
}; |
| 287 |
|
| 288 |
port@2 { |
| 289 |
reg = <2>; |
| 290 |
label = "lan2"; |
| 291 |
}; |
| 292 |
|
| 293 |
port@3 { |
| 294 |
reg = <3>; |
| 295 |
label = "lan3"; |
| 296 |
}; |
| 297 |
|
| 298 |
port@4 { |
| 299 |
reg = <4>; |
| 300 |
label = "lan4"; |
| 301 |
}; |
| 302 |
|
| 303 |
port@5 { |
| 304 |
reg = <5>; |
| 305 |
ethernet = <&gmac1>; |
| 306 |
phy-mode = "rgmii"; |
| 307 |
|
| 308 |
fixed-link { |
| 309 |
speed = <1000>; |
| 310 |
full-duplex; |
| 311 |
pause; |
| 312 |
}; |
| 313 |
}; |
| 314 |
|
| 315 |
port@6 { |
| 316 |
reg = <6>; |
| 317 |
label = "cpu"; |
| 318 |
ethernet = <&gmac0>; |
| 319 |
phy-mode = "2500base-x"; |
| 320 |
|
| 321 |
fixed-link { |
| 322 |
speed = <2500>; |
| 323 |
full-duplex; |
| 324 |
pause; |
| 325 |
}; |
| 326 |
}; |
| 327 |
}; |
| 328 |
}; |
| 329 |
|
| 330 |
&uart0 { |
| 331 |
status = "okay"; |
| 332 |
}; |
| 333 |
|
| 334 |
&uart1 { |
| 335 |
pinctrl-names = "default"; |
| 336 |
pinctrl-0 = <&uart1_pins>; |
| 337 |
status = "okay"; |
| 338 |
}; |
| 339 |
|
| 340 |
&uart2 { |
| 341 |
pinctrl-names = "default"; |
| 342 |
pinctrl-0 = <&uart2_pins>; |
| 343 |
status = "okay"; |
| 344 |
}; |
| 345 |
|
| 346 |
&usb_phy { |
| 347 |
status = "okay"; |
| 348 |
}; |
| 349 |
|
| 350 |
&wifi { |
| 351 |
status = "okay"; |
| 352 |
pinctrl-names = "default", "dbdc"; |
| 353 |
pinctrl-0 = <&wf_2g_5g_pins>; |
| 354 |
pinctrl-1 = <&wf_dbdc_pins>; |
| 355 |
}; |