Debian Codegraph @

scripts/dtc/include-prefixes/arm64/exynos/google/gs101-pixel-common.dtsi

raw
1 // SPDX-License-Identifier: GPL-2.0-only
2 /*
3 * Device Tree nodes common for all GS101-based Pixel
4 *
5 * Copyright 2021-2023 Google LLC
6 * Copyright 2023 Linaro Ltd - <[email protected]>
7 */
8
9 /dts-v1/;
10
11 #include <dt-bindings/gpio/gpio.h>
12 #include <dt-bindings/input/input.h>
13 #include <dt-bindings/usb/pd.h>
14 #include "gs101-pinctrl.h"
15 #include "gs101.dtsi"
16
17 / {
18 aliases {
19 serial0 = &serial_0;
20 };
21
22 chosen {
23 /* Bootloader expects bootargs specified otherwise it crashes */
24 bootargs = "";
25 stdout-path = &serial_0;
26
27 /* Use display framebuffer as setup by bootloader */
28 framebuffer0: framebuffer-0 {
29 compatible = "simple-framebuffer";
30 memory-region = <&cont_splash_mem>;
31 /* format properties to be added by actual board */
32 status = "disabled";
33 };
34 };
35
36 gpio-keys {
37 compatible = "gpio-keys";
38 pinctrl-0 = <&key_voldown>, <&key_volup>, <&key_power>;
39 pinctrl-names = "default";
40
41 button-vol-down {
42 label = "KEY_VOLUMEDOWN";
43 linux,code = <KEY_VOLUMEDOWN>;
44 gpios = <&gpa7 3 GPIO_ACTIVE_LOW>;
45 wakeup-source;
46 };
47
48 button-vol-up {
49 label = "KEY_VOLUMEUP";
50 linux,code = <KEY_VOLUMEUP>;
51 gpios = <&gpa8 1 GPIO_ACTIVE_LOW>;
52 wakeup-source;
53 };
54
55 button-power {
56 label = "KEY_POWER";
57 linux,code = <KEY_POWER>;
58 gpios = <&gpa10 1 GPIO_ACTIVE_LOW>;
59 wakeup-source;
60 };
61 };
62
63 reboot-mode {
64 compatible = "nvmem-reboot-mode";
65 nvmem-cells = <&nvmem_reboot_mode>;
66 nvmem-cell-names = "reboot-mode";
67 mode-bootloader = <0x800000fc>;
68 mode-charge = <0x8000000a>;
69 mode-dm-verity-device-corrupted = <0x80000050>;
70 mode-fastboot = <0x800000fa>;
71 mode-reboot-ab-update = <0x80000052>;
72 mode-recovery = <0x800000ff>;
73 mode-rescue = <0x800000f9>;
74 mode-shutdown-thermal = <0x80000051>;
75 mode-shutdown-thermal-battery = <0x80000051>;
76 };
77
78 /* TODO: Remove this once PMIC is implemented */
79 reg_placeholder: regulator-0 {
80 compatible = "regulator-fixed";
81 regulator-name = "placeholder_reg";
82 };
83
84 /* TODO: Remove this once S2MPG11 slave PMIC is implemented */
85 ufs_0_fixed_vcc_reg: regulator-1 {
86 compatible = "regulator-fixed";
87 regulator-name = "ufs-vcc";
88 gpio = <&gpp0 1 GPIO_ACTIVE_HIGH>;
89 regulator-boot-on;
90 enable-active-high;
91 };
92
93 reserved-memory {
94 cont_splash_mem: splash@fac00000 {
95 /* size to be updated by actual board */
96 reg = <0x0 0xfac00000 0x0>;
97 no-map;
98 status = "disabled";
99 };
100 };
101 };
102
103 &acpm_ipc {
104 pmic {
105 compatible = "samsung,s2mpg10-pmic";
106 interrupts-extended = <&gpa0 6 IRQ_TYPE_LEVEL_LOW>;
107 pinctrl-names = "default";
108 pinctrl-0 = <&pmic_int>;
109 system-power-controller;
110 wakeup-source;
111
112 clocks {
113 compatible = "samsung,s2mpg10-clk";
114 #clock-cells = <1>;
115 clock-output-names = "rtc32k_ap", "peri32k1",
116 "peri32k2";
117 };
118
119 regulators {
120 };
121 };
122 };
123
124 &ext_24_5m {
125 clock-frequency = <24576000>;
126 };
127
128 &ext_200m {
129 clock-frequency = <200000000>;
130 };
131
132 &hsi2c_8 {
133 status = "okay";
134
135 eeprom: eeprom@50 {
136 compatible = "atmel,24c08";
137 reg = <0x50>;
138 };
139 };
140
141 &hsi2c_12 {
142 status = "okay";
143 /* TODO: add the devices once drivers exist */
144
145 usb-typec@25 {
146 compatible = "maxim,max77759-tcpci", "maxim,max33359";
147 reg = <0x25>;
148 interrupts-extended = <&gpa8 2 IRQ_TYPE_LEVEL_LOW>;
149 pinctrl-0 = <&typec_int>;
150 pinctrl-names = "default";
151
152 connector {
153 compatible = "usb-c-connector";
154 label = "USB-C";
155 data-role = "dual";
156 power-role = "dual";
157 self-powered;
158 try-power-role = "sink";
159 op-sink-microwatt = <2600000>;
160 slow-charger-loop;
161 /*
162 * max77759 operating in reverse boost mode (0xA) can
163 * source up to 1.5A while extboost can only do ~1A.
164 * Since extboost is the primary path, advertise 900mA.
165 */
166 source-pdos = <PDO_FIXED(5000, 900,
167 (PDO_FIXED_SUSPEND
168 | PDO_FIXED_USB_COMM
169 | PDO_FIXED_DATA_SWAP
170 | PDO_FIXED_DUAL_ROLE))>;
171 sink-pdos = <PDO_FIXED(5000, 3000,
172 (PDO_FIXED_DATA_SWAP
173 | PDO_FIXED_USB_COMM
174 | PDO_FIXED_HIGHER_CAP
175 | PDO_FIXED_DUAL_ROLE))
176 PDO_FIXED(9000, 2200, 0)
177 PDO_PPS_APDO(5000, 11000, 3000)>;
178 sink-vdos = <VDO_IDH(1, 1, IDH_PTYPE_PERIPH, 0,
179 IDH_PTYPE_DFP_HOST, 2, 0x18d1)
180 VDO_CERT(0x0)
181 VDO_PRODUCT(0x4ee1, 0x0)
182 VDO_UFP(UFP_VDO_VER1_2,
183 (DEV_USB2_CAPABLE
184 | DEV_USB3_CAPABLE),
185 UFP_RECEPTACLE, 0,
186 AMA_VCONN_NOT_REQ, 0,
187 UFP_ALTMODE_NOT_SUPP,
188 UFP_USB32_GEN1)
189 /* padding */ 0
190 VDO_DFP(DFP_VDO_VER1_1,
191 (HOST_USB2_CAPABLE
192 | HOST_USB3_CAPABLE),
193 DFP_RECEPTACLE, 0)>;
194 sink-vdos-v1 = <VDO_IDH(1, 1, IDH_PTYPE_PERIPH, 0,
195 0, 0, 0x18d1)
196 VDO_CERT(0x0)
197 VDO_PRODUCT(0x4ee1, 0x0)>;
198 /*
199 * Until bootloader is updated to set those two when
200 * console is enabled, we disable PD here.
201 */
202 pd-disable;
203 typec-power-opmode = "default";
204
205 ports {
206 #address-cells = <1>;
207 #size-cells = <0>;
208
209 port@0 {
210 reg = <0>;
211
212 usbc0_orien_sw: endpoint {
213 remote-endpoint = <&usbdrd31_phy_orien_switch>;
214 };
215 };
216
217 port@1 {
218 reg = <1>;
219
220 usbc0_role_sw: endpoint {
221 remote-endpoint = <&usbdrd31_dwc3_role_switch>;
222 };
223 };
224 };
225 };
226 };
227
228 pmic@66 {
229 compatible = "maxim,max77759";
230 reg = <0x66>;
231
232 pinctrl-0 = <&if_pmic_int>;
233 pinctrl-names = "default";
234 interrupts-extended = <&gpa8 3 IRQ_TYPE_LEVEL_LOW>;
235
236 interrupt-controller;
237 #interrupt-cells = <2>;
238
239 gpio {
240 compatible = "maxim,max77759-gpio";
241
242 gpio-controller;
243 #gpio-cells = <2>;
244 /*
245 * "Human-readable name [SIGNAL_LABEL]" where the
246 * latter comes from the schematic
247 */
248 gpio-line-names = "OTG boost [OTG_BOOST_EN]",
249 "max20339 IRQ [MW_OVP_INT_L]";
250
251 interrupt-controller;
252 #interrupt-cells = <2>;
253 };
254
255 nvmem-0 {
256 compatible = "maxim,max77759-nvmem";
257
258 nvmem-layout {
259 compatible = "fixed-layout";
260 #address-cells = <1>;
261 #size-cells = <1>;
262
263 nvmem_reboot_mode: reboot-mode@0 {
264 reg = <0x0 0x4>;
265 };
266
267 boot-reason@4 {
268 reg = <0x4 0x4>;
269 };
270
271 shutdown-user-flag@8 {
272 reg = <0x8 0x1>;
273 };
274
275 rsoc@a {
276 reg = <0xa 0x2>;
277 };
278 };
279 };
280 };
281 };
282
283 &pinctrl_far_alive {
284 key_voldown: key-voldown-pins {
285 samsung,pins = "gpa7-3";
286 samsung,pin-function = <GS101_PIN_FUNC_EINT>;
287 samsung,pin-pud = <GS101_PIN_PULL_NONE>;
288 samsung,pin-drv = <GS101_PIN_DRV_2_5_MA>;
289 };
290
291 key_volup: key-volup-pins {
292 samsung,pins = "gpa8-1";
293 samsung,pin-function = <GS101_PIN_FUNC_EINT>;
294 samsung,pin-pud = <GS101_PIN_PULL_NONE>;
295 samsung,pin-drv = <GS101_PIN_DRV_2_5_MA>;
296 };
297
298 typec_int: typec-int-pins {
299 samsung,pins = "gpa8-2";
300 samsung,pin-function = <GS101_PIN_FUNC_EINT>;
301 samsung,pin-pud = <GS101_PIN_PULL_UP>;
302 samsung,pin-drv = <GS101_PIN_DRV_2_5_MA>;
303 };
304
305 if_pmic_int: if-pmic-int-pins {
306 samsung,pins = "gpa8-3";
307 samsung,pin-function = <GS101_PIN_FUNC_EINT>;
308 samsung,pin-pud = <GS101_PIN_PULL_UP>;
309 samsung,pin-drv = <GS101_PIN_DRV_2_5_MA>;
310 };
311 };
312
313 &pinctrl_gpio_alive {
314 pmic_int: pmic-int-pins {
315 samsung,pins = "gpa0-6";
316 samsung,pin-function = <GS101_PIN_FUNC_EINT>;
317 samsung,pin-pud = <GS101_PIN_PULL_NONE>;
318 };
319
320 key_power: key-power-pins {
321 samsung,pins = "gpa10-1";
322 samsung,pin-function = <GS101_PIN_FUNC_EINT>;
323 samsung,pin-pud = <GS101_PIN_PULL_NONE>;
324 samsung,pin-drv = <GS101_PIN_DRV_2_5_MA>;
325 };
326 };
327
328 &serial_0 {
329 status = "okay";
330 };
331
332 &ufs_0 {
333 status = "okay";
334 vcc-supply = <&ufs_0_fixed_vcc_reg>;
335 };
336
337 &ufs_0_phy {
338 status = "okay";
339 };
340
341 &usbdrd31 {
342 vdd10-supply = <&reg_placeholder>;
343 vdd33-supply = <&reg_placeholder>;
344 status = "okay";
345 };
346
347 &usbdrd31_dwc3 {
348 dr_mode = "otg";
349 usb-role-switch;
350 role-switch-default-mode = "peripheral";
351 maximum-speed = "super-speed-plus";
352 status = "okay";
353
354 port {
355 usbdrd31_dwc3_role_switch: endpoint {
356 remote-endpoint = <&usbc0_role_sw>;
357 };
358 };
359 };
360
361 &usbdrd31_phy {
362 orientation-switch;
363 /* TODO: Update these once PMIC is implemented */
364 pll-supply = <&reg_placeholder>;
365 dvdd-usb20-supply = <&reg_placeholder>;
366 vddh-usb20-supply = <&reg_placeholder>;
367 vdd33-usb20-supply = <&reg_placeholder>;
368 vdda-usbdp-supply = <&reg_placeholder>;
369 vddh-usbdp-supply = <&reg_placeholder>;
370 status = "okay";
371
372 port {
373 usbdrd31_phy_orien_switch: endpoint {
374 remote-endpoint = <&usbc0_orien_sw>;
375 };
376 };
377 };
378
379 &usi_uart {
380 samsung,clkreq-on; /* needed for UART mode */
381 status = "okay";
382 };
383
384 &usi8 {
385 samsung,mode = <USI_MODE_I2C>;
386 status = "okay";
387 };
388
389 &usi12 {
390 samsung,mode = <USI_MODE_I2C>;
391 status = "okay";
392 };
393
394 &watchdog_cl0 {
395 timeout-sec = <30>;
396 status = "okay";
397 };