Debian Codegraph @

scripts/dtc/include-prefixes/arm64/exynos/exynos850-e850-96.dts

raw
1 // SPDX-License-Identifier: GPL-2.0
2 /*
3 * WinLink E850-96 board device tree source
4 *
5 * Copyright (C) 2018 Samsung Electronics Co., Ltd.
6 * Copyright (C) 2021 Linaro Ltd.
7 *
8 * Device tree source file for WinLink's E850-96 board which is based on
9 * Samsung Exynos850 SoC.
10 */
11
12 /dts-v1/;
13
14 #include "exynos850.dtsi"
15 #include <dt-bindings/gpio/gpio.h>
16 #include <dt-bindings/input/input.h>
17 #include <dt-bindings/leds/common.h>
18
19 / {
20 model = "WinLink E850-96 board";
21 compatible = "winlink,e850-96", "samsung,exynos850";
22
23 aliases {
24 ethernet0 = &ethernet;
25 mmc0 = &mmc_0;
26 serial0 = &serial_0;
27 };
28
29 chosen {
30 stdout-path = &serial_0;
31 };
32
33 connector {
34 compatible = "gpio-usb-b-connector", "usb-b-connector";
35 label = "micro-USB";
36 type = "micro";
37 vbus-supply = <&reg_usb_host_vbus>;
38 id-gpios = <&gpa0 0 GPIO_ACTIVE_LOW>;
39 pinctrl-names = "default";
40 pinctrl-0 = <&micro_usb_det_pins>;
41
42 port {
43 usb_dr_connector: endpoint {
44 remote-endpoint = <&usb1_drd_sw>;
45 };
46 };
47 };
48
49 memory@80000000 {
50 device_type = "memory";
51 reg = <0x0 0x80000000 0x80000000>,
52 <0x8 0x80000000 0x80000000>;
53 };
54
55 gpio-keys {
56 compatible = "gpio-keys";
57 pinctrl-names = "default";
58 pinctrl-0 = <&key_voldown_pins &key_volup_pins>;
59
60 volume-down-key {
61 label = "Volume Down";
62 linux,code = <KEY_VOLUMEDOWN>;
63 gpios = <&gpa1 0 GPIO_ACTIVE_LOW>;
64 };
65
66 volume-up-key {
67 label = "Volume Up";
68 linux,code = <KEY_VOLUMEUP>;
69 gpios = <&gpa0 7 GPIO_ACTIVE_LOW>;
70 };
71 };
72
73 leds {
74 compatible = "gpio-leds";
75
76 /* HEART_BEAT_LED */
77 user_led1: led-1 {
78 label = "yellow:user1";
79 gpios = <&gpg2 2 GPIO_ACTIVE_HIGH>;
80 color = <LED_COLOR_ID_YELLOW>;
81 function = LED_FUNCTION_HEARTBEAT;
82 linux,default-trigger = "heartbeat";
83 };
84
85 /* eMMC_LED */
86 user_led2: led-2 {
87 label = "yellow:user2";
88 gpios = <&gpg2 3 GPIO_ACTIVE_HIGH>;
89 color = <LED_COLOR_ID_YELLOW>;
90 linux,default-trigger = "mmc0";
91 };
92
93 /* SD_LED */
94 user_led3: led-3 {
95 label = "white:user3";
96 gpios = <&gpg2 4 GPIO_ACTIVE_HIGH>;
97 color = <LED_COLOR_ID_WHITE>;
98 function = LED_FUNCTION_SD;
99 linux,default-trigger = "mmc2";
100 };
101
102 /* WIFI_LED */
103 wlan_active_led: led-4 {
104 label = "yellow:wlan";
105 gpios = <&gpg2 6 GPIO_ACTIVE_HIGH>;
106 color = <LED_COLOR_ID_YELLOW>;
107 function = LED_FUNCTION_WLAN;
108 linux,default-trigger = "phy0tx";
109 default-state = "off";
110 };
111
112 /* BLUETOOTH_LED */
113 bt_active_led: led-5 {
114 label = "blue:bt";
115 gpios = <&gpg2 7 GPIO_ACTIVE_HIGH>;
116 color = <LED_COLOR_ID_BLUE>;
117 function = LED_FUNCTION_BLUETOOTH;
118 linux,default-trigger = "hci0-power";
119 default-state = "off";
120 };
121 };
122
123 /* TODO: Remove this once PMIC is implemented */
124 reg_dummy: regulator-0 {
125 compatible = "regulator-fixed";
126 regulator-name = "dummy_reg";
127 };
128
129 reg_usb_host_vbus: regulator-1 {
130 compatible = "regulator-fixed";
131 regulator-name = "usb_host_vbus";
132 regulator-min-microvolt = <5000000>;
133 regulator-max-microvolt = <5000000>;
134 gpio = <&gpa3 5 GPIO_ACTIVE_LOW>;
135 };
136
137 reserved-memory {
138 #address-cells = <2>;
139 #size-cells = <1>;
140 ranges;
141
142 secure_mem: memory@bab00000 {
143 reg = <0x0 0xbab00000 0x5500000>;
144 no-map;
145 };
146
147 ramoops@f0000000 {
148 compatible = "ramoops";
149 reg = <0x0 0xf0000000 0x200000>;
150 record-size = <0x20000>;
151 console-size = <0x20000>;
152 ftrace-size = <0x100000>;
153 pmsg-size = <0x20000>;
154 };
155 };
156
157 /*
158 * RTC clock (XrtcXTI); external, must be 32.768 kHz.
159 *
160 * TODO: Remove this once RTC clock is implemented properly as part of
161 * PMIC driver.
162 */
163 rtcclk: clock-rtcclk {
164 compatible = "fixed-clock";
165 clock-output-names = "rtcclk";
166 #clock-cells = <0>;
167 clock-frequency = <32768>;
168 };
169 };
170
171 &cmu_hsi {
172 clocks = <&oscclk>, <&rtcclk>,
173 <&cmu_top CLK_DOUT_HSI_BUS>,
174 <&cmu_top CLK_DOUT_HSI_MMC_CARD>,
175 <&cmu_top CLK_DOUT_HSI_USB20DRD>;
176 clock-names = "oscclk", "rtcclk", "dout_hsi_bus",
177 "dout_hsi_mmc_card", "dout_hsi_usb20drd";
178 };
179
180 &mmc_0 {
181 status = "okay";
182 mmc-hs200-1_8v;
183 mmc-hs400-1_8v;
184 cap-mmc-highspeed;
185 non-removable;
186 mmc-hs400-enhanced-strobe;
187 card-detect-delay = <200>;
188 clock-frequency = <800000000>;
189 bus-width = <8>;
190 samsung,dw-mshc-ciu-div = <3>;
191 samsung,dw-mshc-sdr-timing = <0 4>;
192 samsung,dw-mshc-ddr-timing = <2 4>;
193 samsung,dw-mshc-hs400-timing = <0 2>;
194
195 pinctrl-names = "default";
196 pinctrl-0 = <&sd0_clk_pins &sd0_cmd_pins &sd0_rdqs_pins &sd0_nreset_pins
197 &sd0_bus1_pins &sd0_bus4_pins &sd0_bus8_pins>;
198 };
199
200 &oscclk {
201 clock-frequency = <26000000>;
202 };
203
204 &pinctrl_alive {
205 key_voldown_pins: key-voldown-pins {
206 samsung,pins = "gpa1-0";
207 samsung,pin-function = <EXYNOS_PIN_FUNC_EINT>;
208 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
209 samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
210 };
211
212 key_volup_pins: key-volup-pins {
213 samsung,pins = "gpa0-7";
214 samsung,pin-function = <EXYNOS_PIN_FUNC_EINT>;
215 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
216 samsung,pin-drv = <EXYNOS5420_PIN_DRV_LV1>;
217 };
218
219 micro_usb_det_pins: micro-usb-det-pins {
220 samsung,pins = "gpa0-0";
221 samsung,pin-function = <EXYNOS_PIN_FUNC_INPUT>;
222 samsung,pin-pud = <EXYNOS_PIN_PULL_NONE>;
223 };
224 };
225
226 &rtc {
227 status = "okay";
228 clocks = <&cmu_apm CLK_GOUT_RTC_PCLK>, <&rtcclk>;
229 clock-names = "rtc", "rtc_src";
230 };
231
232 &serial_0 {
233 status = "okay";
234 pinctrl-names = "default";
235 pinctrl-0 = <&uart1_pins>;
236 };
237
238 &usbdrd {
239 status = "okay";
240 vdd10-supply = <&reg_dummy>;
241 vdd33-supply = <&reg_dummy>;
242 };
243
244 &usbdrd_dwc3 {
245 #address-cells = <1>;
246 #size-cells = <0>;
247 dr_mode = "otg";
248 usb-role-switch;
249 role-switch-default-mode = "host";
250
251 hub@1 {
252 compatible = "usb424,9514";
253 reg = <1>;
254 #address-cells = <1>;
255 #size-cells = <0>;
256
257 ethernet: ethernet@1 {
258 compatible = "usb424,ec00";
259 reg = <1>;
260 };
261 };
262
263 port {
264 usb1_drd_sw: endpoint {
265 remote-endpoint = <&usb_dr_connector>;
266 };
267 };
268 };
269
270 &usbdrd_phy {
271 status = "okay";
272 };
273
274 &usi_uart {
275 samsung,clkreq-on; /* needed for UART mode */
276 status = "okay";
277 };
278
279 &watchdog_cl0 {
280 status = "okay";
281 };
282
283 &watchdog_cl1 {
284 status = "okay";
285 };