Debian Codegraph @

scripts/dtc/include-prefixes/arm64/allwinner/sun50i-h618-orangepi-zero2w.dts

raw
1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2 /*
3 * Copyright (C) 2023 Arm Ltd.
4 */
5
6 /dts-v1/;
7
8 #include "sun50i-h616.dtsi"
9 #include "sun50i-h616-cpu-opp.dtsi"
10
11 #include <dt-bindings/gpio/gpio.h>
12 #include <dt-bindings/interrupt-controller/arm-gic.h>
13 #include <dt-bindings/leds/common.h>
14
15 / {
16 model = "OrangePi Zero 2W";
17 compatible = "xunlong,orangepi-zero2w", "allwinner,sun50i-h618";
18
19 aliases {
20 serial0 = &uart0;
21 };
22
23 chosen {
24 stdout-path = "serial0:115200n8";
25 };
26
27 leds {
28 compatible = "gpio-leds";
29
30 led-0 {
31 function = LED_FUNCTION_STATUS;
32 color = <LED_COLOR_ID_GREEN>;
33 gpios = <&pio 2 13 GPIO_ACTIVE_HIGH>; /* PC13 */
34 };
35 };
36
37 reg_vcc5v: vcc5v {
38 /* board wide 5V supply directly from the USB-C socket */
39 compatible = "regulator-fixed";
40 regulator-name = "vcc-5v";
41 regulator-min-microvolt = <5000000>;
42 regulator-max-microvolt = <5000000>;
43 regulator-always-on;
44 };
45
46 reg_vcc3v3: vcc3v3 {
47 /* SY8089 DC/DC converter */
48 compatible = "regulator-fixed";
49 regulator-name = "vcc-3v3";
50 regulator-min-microvolt = <3300000>;
51 regulator-max-microvolt = <3300000>;
52 vin-supply = <&reg_vcc5v>;
53 regulator-always-on;
54 };
55 };
56
57 &codec {
58 allwinner,audio-routing = "Line Out", "LINEOUT";
59 status = "okay";
60 };
61
62 &cpu0 {
63 cpu-supply = <&reg_dcdc2>;
64 };
65
66 &ehci1 {
67 status = "okay";
68 };
69
70 /* USB 2 & 3 are on the FPC connector (or the exansion board) */
71
72 &gpu {
73 mali-supply = <&reg_dcdc1>;
74 status = "okay";
75 };
76
77 &mmc0 {
78 cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
79 bus-width = <4>;
80 vmmc-supply = <&reg_vcc3v3>;
81 status = "okay";
82 };
83
84 &ohci1 {
85 status = "okay";
86 };
87
88 &pio {
89 vcc-pc-supply = <&reg_dldo1>;
90 vcc-pf-supply = <&reg_dldo1>; /* internally via VCC-IO */
91 vcc-pg-supply = <&reg_aldo1>;
92 vcc-ph-supply = <&reg_dldo1>; /* internally via VCC-IO */
93 vcc-pi-supply = <&reg_dldo1>;
94 };
95
96 &r_i2c {
97 status = "okay";
98
99 axp313: pmic@36 {
100 compatible = "x-powers,axp313a";
101 reg = <0x36>;
102 #interrupt-cells = <1>;
103 interrupt-controller;
104 interrupt-parent = <&pio>;
105 interrupts = <2 9 IRQ_TYPE_LEVEL_LOW>; /* PC9 */
106
107 vin1-supply = <&reg_vcc5v>;
108 vin2-supply = <&reg_vcc5v>;
109 vin3-supply = <&reg_vcc5v>;
110
111 regulators {
112 /* Supplies VCC-PLL and DRAM */
113 reg_aldo1: aldo1 {
114 regulator-always-on;
115 regulator-min-microvolt = <1800000>;
116 regulator-max-microvolt = <1800000>;
117 regulator-name = "vcc1v8";
118 };
119
120 /* Supplies VCC-IO, so needs to be always on. */
121 reg_dldo1: dldo1 {
122 regulator-always-on;
123 regulator-min-microvolt = <3300000>;
124 regulator-max-microvolt = <3300000>;
125 regulator-name = "vcc3v3";
126 };
127
128 reg_dcdc1: dcdc1 {
129 regulator-always-on;
130 regulator-min-microvolt = <810000>;
131 regulator-max-microvolt = <990000>;
132 regulator-name = "vdd-gpu-sys";
133 };
134
135 reg_dcdc2: dcdc2 {
136 regulator-always-on;
137 regulator-min-microvolt = <810000>;
138 regulator-max-microvolt = <1100000>;
139 regulator-name = "vdd-cpu";
140 };
141
142 reg_dcdc3: dcdc3 {
143 regulator-always-on;
144 regulator-min-microvolt = <1100000>;
145 regulator-max-microvolt = <1100000>;
146 regulator-name = "vdd-dram";
147 };
148 };
149 };
150 };
151
152 &spi0 {
153 status = "okay";
154 pinctrl-names = "default";
155 pinctrl-0 = <&spi0_pins>, <&spi0_cs0_pin>;
156
157 flash@0 {
158 #address-cells = <1>;
159 #size-cells = <1>;
160 compatible = "jedec,spi-nor";
161 reg = <0>;
162 spi-max-frequency = <40000000>;
163 };
164 };
165
166 &uart0 {
167 pinctrl-names = "default";
168 pinctrl-0 = <&uart0_ph_pins>;
169 status = "okay";
170 };
171
172 &usbotg {
173 /*
174 * PHY0 pins are connected to a USB-C socket, but a role switch
175 * is not implemented: both CC pins are pulled to GND.
176 * The VBUS pins power the device, so a fixed peripheral mode
177 * is the best choice.
178 * The board can be powered via GPIOs, in this case port0 *can*
179 * act as a host (with a cable/adapter ignoring CC), as VBUS is
180 * then provided by the GPIOs. Any user of this setup would
181 * need to adjust the DT accordingly: dr_mode set to "host",
182 * enabling OHCI0 and EHCI0.
183 */
184 dr_mode = "peripheral";
185 status = "okay";
186 };
187
188 &usbphy {
189 usb1_vbus-supply = <&reg_vcc5v>;
190 status = "okay";
191 };