| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
// Copyright (c) 2017 Icenowy Zheng <[email protected]> |
| 3 |
|
| 4 |
/dts-v1/; |
| 5 |
|
| 6 |
#include "sun50i-h6.dtsi" |
| 7 |
#include "sun50i-h6-cpu-opp.dtsi" |
| 8 |
|
| 9 |
#include <dt-bindings/gpio/gpio.h> |
| 10 |
|
| 11 |
/ { |
| 12 |
model = "Pine64 PINE H64 Model A"; |
| 13 |
compatible = "pine64,pine-h64", "allwinner,sun50i-h6"; |
| 14 |
|
| 15 |
aliases { |
| 16 |
ethernet0 = &emac; |
| 17 |
serial0 = &uart0; |
| 18 |
spi0 = &spi0; |
| 19 |
}; |
| 20 |
|
| 21 |
chosen { |
| 22 |
stdout-path = "serial0:115200n8"; |
| 23 |
}; |
| 24 |
|
| 25 |
ext_osc32k: ext-osc32k-clk { |
| 26 |
#clock-cells = <0>; |
| 27 |
compatible = "fixed-clock"; |
| 28 |
clock-frequency = <32768>; |
| 29 |
clock-output-names = "ext_osc32k"; |
| 30 |
}; |
| 31 |
|
| 32 |
hdmi_connector: connector { |
| 33 |
compatible = "hdmi-connector"; |
| 34 |
type = "a"; |
| 35 |
ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */ |
| 36 |
|
| 37 |
port { |
| 38 |
hdmi_con_in: endpoint { |
| 39 |
remote-endpoint = <&hdmi_out_con>; |
| 40 |
}; |
| 41 |
}; |
| 42 |
}; |
| 43 |
|
| 44 |
leds { |
| 45 |
compatible = "gpio-leds"; |
| 46 |
|
| 47 |
led-0 { |
| 48 |
label = "pine-h64:green:heartbeat"; |
| 49 |
gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */ |
| 50 |
}; |
| 51 |
|
| 52 |
led-1 { |
| 53 |
label = "pine-h64:white:link"; |
| 54 |
gpios = <&r_pio 0 3 GPIO_ACTIVE_HIGH>; /* PL3 */ |
| 55 |
}; |
| 56 |
|
| 57 |
led-2 { |
| 58 |
label = "pine-h64:blue:status"; |
| 59 |
gpios = <&r_pio 0 7 GPIO_ACTIVE_HIGH>; /* PL7 */ |
| 60 |
}; |
| 61 |
}; |
| 62 |
|
| 63 |
reg_gmac_3v3: gmac-3v3 { |
| 64 |
compatible = "regulator-fixed"; |
| 65 |
regulator-name = "vcc-gmac-3v3"; |
| 66 |
regulator-min-microvolt = <3300000>; |
| 67 |
regulator-max-microvolt = <3300000>; |
| 68 |
startup-delay-us = <100000>; |
| 69 |
gpio = <&pio 2 16 GPIO_ACTIVE_HIGH>; |
| 70 |
enable-active-high; |
| 71 |
}; |
| 72 |
|
| 73 |
reg_usb_vbus: vbus { |
| 74 |
compatible = "regulator-fixed"; |
| 75 |
regulator-name = "usb-vbus"; |
| 76 |
regulator-min-microvolt = <5000000>; |
| 77 |
regulator-max-microvolt = <5000000>; |
| 78 |
startup-delay-us = <100000>; |
| 79 |
gpio = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; |
| 80 |
enable-active-high; |
| 81 |
}; |
| 82 |
}; |
| 83 |
|
| 84 |
&cpu0 { |
| 85 |
cpu-supply = <®_dcdca>; |
| 86 |
}; |
| 87 |
|
| 88 |
&de { |
| 89 |
status = "okay"; |
| 90 |
}; |
| 91 |
|
| 92 |
&ehci0 { |
| 93 |
status = "okay"; |
| 94 |
}; |
| 95 |
|
| 96 |
&ehci3 { |
| 97 |
status = "okay"; |
| 98 |
}; |
| 99 |
|
| 100 |
&emac { |
| 101 |
pinctrl-names = "default"; |
| 102 |
pinctrl-0 = <&ext_rgmii_pins>; |
| 103 |
phy-mode = "rgmii-id"; |
| 104 |
phy-handle = <&ext_rgmii_phy>; |
| 105 |
phy-supply = <®_gmac_3v3>; |
| 106 |
allwinner,rx-delay-ps = <200>; |
| 107 |
allwinner,tx-delay-ps = <200>; |
| 108 |
status = "okay"; |
| 109 |
}; |
| 110 |
|
| 111 |
&gpu { |
| 112 |
mali-supply = <®_dcdcc>; |
| 113 |
status = "okay"; |
| 114 |
}; |
| 115 |
|
| 116 |
&hdmi { |
| 117 |
status = "okay"; |
| 118 |
}; |
| 119 |
|
| 120 |
&hdmi_out { |
| 121 |
hdmi_out_con: endpoint { |
| 122 |
remote-endpoint = <&hdmi_con_in>; |
| 123 |
}; |
| 124 |
}; |
| 125 |
|
| 126 |
&mdio { |
| 127 |
ext_rgmii_phy: ethernet-phy@1 { |
| 128 |
compatible = "ethernet-phy-ieee802.3-c22"; |
| 129 |
reg = <1>; |
| 130 |
}; |
| 131 |
}; |
| 132 |
|
| 133 |
&mmc0 { |
| 134 |
vmmc-supply = <®_cldo1>; |
| 135 |
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; |
| 136 |
disable-wp; |
| 137 |
bus-width = <4>; |
| 138 |
status = "okay"; |
| 139 |
}; |
| 140 |
|
| 141 |
&mmc2 { |
| 142 |
vmmc-supply = <®_cldo1>; |
| 143 |
vqmmc-supply = <®_bldo2>; |
| 144 |
non-removable; |
| 145 |
cap-mmc-hw-reset; |
| 146 |
mmc-hs200-1_8v; |
| 147 |
bus-width = <8>; |
| 148 |
status = "okay"; |
| 149 |
}; |
| 150 |
|
| 151 |
&ohci0 { |
| 152 |
status = "okay"; |
| 153 |
}; |
| 154 |
|
| 155 |
&ohci3 { |
| 156 |
status = "okay"; |
| 157 |
}; |
| 158 |
|
| 159 |
&pio { |
| 160 |
vcc-pc-supply = <®_bldo2>; |
| 161 |
vcc-pd-supply = <®_cldo1>; |
| 162 |
vcc-pg-supply = <®_aldo1>; |
| 163 |
}; |
| 164 |
|
| 165 |
&r_i2c { |
| 166 |
status = "okay"; |
| 167 |
|
| 168 |
axp805: pmic@36 { |
| 169 |
compatible = "x-powers,axp805", "x-powers,axp806"; |
| 170 |
reg = <0x36>; |
| 171 |
interrupt-parent = <&r_intc>; |
| 172 |
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>; |
| 173 |
interrupt-controller; |
| 174 |
#interrupt-cells = <1>; |
| 175 |
x-powers,self-working-mode; |
| 176 |
|
| 177 |
regulators { |
| 178 |
reg_aldo1: aldo1 { |
| 179 |
regulator-always-on; |
| 180 |
regulator-min-microvolt = <3300000>; |
| 181 |
regulator-max-microvolt = <3300000>; |
| 182 |
regulator-name = "vcc-pl"; |
| 183 |
}; |
| 184 |
|
| 185 |
reg_aldo2: aldo2 { |
| 186 |
regulator-min-microvolt = <3300000>; |
| 187 |
regulator-max-microvolt = <3300000>; |
| 188 |
regulator-name = "vcc-ac200"; |
| 189 |
regulator-enable-ramp-delay = <100000>; |
| 190 |
}; |
| 191 |
|
| 192 |
reg_aldo3: aldo3 { |
| 193 |
/* This regulator is connected with CLDO1 */ |
| 194 |
regulator-always-on; |
| 195 |
regulator-min-microvolt = <3300000>; |
| 196 |
regulator-max-microvolt = <3300000>; |
| 197 |
regulator-name = "vcc-3v3-1"; |
| 198 |
}; |
| 199 |
|
| 200 |
reg_bldo1: bldo1 { |
| 201 |
regulator-always-on; |
| 202 |
regulator-min-microvolt = <1800000>; |
| 203 |
regulator-max-microvolt = <1800000>; |
| 204 |
regulator-name = "vcc-bias-pll"; |
| 205 |
}; |
| 206 |
|
| 207 |
reg_bldo2: bldo2 { |
| 208 |
regulator-always-on; |
| 209 |
regulator-min-microvolt = <1800000>; |
| 210 |
regulator-max-microvolt = <1800000>; |
| 211 |
regulator-name = "vcc-efuse-pcie-hdmi-io"; |
| 212 |
}; |
| 213 |
|
| 214 |
reg_bldo3: bldo3 { |
| 215 |
regulator-always-on; |
| 216 |
regulator-min-microvolt = <1800000>; |
| 217 |
regulator-max-microvolt = <1800000>; |
| 218 |
regulator-name = "vcc-dcxoio"; |
| 219 |
}; |
| 220 |
|
| 221 |
bldo4 { |
| 222 |
/* unused */ |
| 223 |
}; |
| 224 |
|
| 225 |
reg_cldo1: cldo1 { |
| 226 |
/* This regulator is connected with ALDO3 */ |
| 227 |
regulator-always-on; |
| 228 |
regulator-min-microvolt = <3300000>; |
| 229 |
regulator-max-microvolt = <3300000>; |
| 230 |
regulator-name = "vcc-3v3-2"; |
| 231 |
}; |
| 232 |
|
| 233 |
reg_cldo2: cldo2 { |
| 234 |
regulator-min-microvolt = <3300000>; |
| 235 |
regulator-max-microvolt = <3300000>; |
| 236 |
regulator-name = "vcc-wifi-1"; |
| 237 |
}; |
| 238 |
|
| 239 |
reg_cldo3: cldo3 { |
| 240 |
regulator-min-microvolt = <3300000>; |
| 241 |
regulator-max-microvolt = <3300000>; |
| 242 |
regulator-name = "vcc-wifi-2"; |
| 243 |
}; |
| 244 |
|
| 245 |
reg_dcdca: dcdca { |
| 246 |
regulator-always-on; |
| 247 |
regulator-min-microvolt = <810000>; |
| 248 |
regulator-max-microvolt = <1160000>; |
| 249 |
regulator-ramp-delay = <2500>; |
| 250 |
regulator-name = "vdd-cpu"; |
| 251 |
}; |
| 252 |
|
| 253 |
reg_dcdcc: dcdcc { |
| 254 |
regulator-enable-ramp-delay = <32000>; |
| 255 |
regulator-min-microvolt = <810000>; |
| 256 |
regulator-max-microvolt = <1080000>; |
| 257 |
regulator-ramp-delay = <2500>; |
| 258 |
regulator-name = "vdd-gpu"; |
| 259 |
}; |
| 260 |
|
| 261 |
reg_dcdcd: dcdcd { |
| 262 |
regulator-always-on; |
| 263 |
regulator-min-microvolt = <960000>; |
| 264 |
regulator-max-microvolt = <960000>; |
| 265 |
regulator-name = "vdd-sys"; |
| 266 |
}; |
| 267 |
|
| 268 |
reg_dcdce: dcdce { |
| 269 |
regulator-always-on; |
| 270 |
regulator-min-microvolt = <1200000>; |
| 271 |
regulator-max-microvolt = <1200000>; |
| 272 |
regulator-name = "vcc-dram"; |
| 273 |
}; |
| 274 |
|
| 275 |
sw { |
| 276 |
/* unused */ |
| 277 |
}; |
| 278 |
}; |
| 279 |
}; |
| 280 |
|
| 281 |
pcf8563: rtc@51 { |
| 282 |
compatible = "nxp,pcf8563"; |
| 283 |
reg = <0x51>; |
| 284 |
interrupt-parent = <&r_intc>; |
| 285 |
interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>; |
| 286 |
#clock-cells = <0>; |
| 287 |
}; |
| 288 |
}; |
| 289 |
|
| 290 |
&r_ir { |
| 291 |
status = "okay"; |
| 292 |
}; |
| 293 |
|
| 294 |
&r_pio { |
| 295 |
vcc-pm-supply = <®_aldo1>; |
| 296 |
}; |
| 297 |
|
| 298 |
&rtc { |
| 299 |
clocks = <&ext_osc32k>; |
| 300 |
}; |
| 301 |
|
| 302 |
/* |
| 303 |
* The CS pin is shared with the MMC2 CMD pin, so we cannot have the SPI |
| 304 |
* flash and eMMC at the same time, as one of them would fail probing. |
| 305 |
* Disable SPI0 in here, to prefer the more useful eMMC. U-Boot can |
| 306 |
* fix this up in no eMMC is connected. |
| 307 |
*/ |
| 308 |
&spi0 { |
| 309 |
pinctrl-0 = <&spi0_pins>, <&spi0_cs_pin>; |
| 310 |
pinctrl-names = "default"; |
| 311 |
status = "disabled"; |
| 312 |
|
| 313 |
flash@0 { |
| 314 |
compatible = "winbond,w25q128", "jedec,spi-nor"; |
| 315 |
reg = <0>; |
| 316 |
spi-max-frequency = <4000000>; |
| 317 |
}; |
| 318 |
}; |
| 319 |
|
| 320 |
&uart0 { |
| 321 |
pinctrl-names = "default"; |
| 322 |
pinctrl-0 = <&uart0_ph_pins>; |
| 323 |
status = "okay"; |
| 324 |
}; |
| 325 |
|
| 326 |
&usb2otg { |
| 327 |
dr_mode = "host"; |
| 328 |
status = "okay"; |
| 329 |
}; |
| 330 |
|
| 331 |
&usb2phy { |
| 332 |
usb0_vbus-supply = <®_usb_vbus>; |
| 333 |
usb3_vbus-supply = <®_usb_vbus>; |
| 334 |
status = "okay"; |
| 335 |
}; |