| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
// Copyright (C) 2018 Jagan Teki <[email protected]> |
| 3 |
|
| 4 |
#include "sun50i-h6-orangepi.dtsi" |
| 5 |
|
| 6 |
/ { |
| 7 |
model = "OrangePi Lite2"; |
| 8 |
compatible = "xunlong,orangepi-lite2", "allwinner,sun50i-h6"; |
| 9 |
|
| 10 |
aliases { |
| 11 |
serial1 = &uart1; /* BT-UART */ |
| 12 |
}; |
| 13 |
|
| 14 |
wifi_pwrseq: pwrseq { |
| 15 |
compatible = "mmc-pwrseq-simple"; |
| 16 |
clocks = <&rtc CLK_OSC32K_FANOUT>; |
| 17 |
clock-names = "ext_clock"; |
| 18 |
reset-gpios = <&r_pio 1 3 GPIO_ACTIVE_LOW>; /* PM3 */ |
| 19 |
post-power-on-delay-ms = <200>; |
| 20 |
}; |
| 21 |
}; |
| 22 |
|
| 23 |
&mmc1 { |
| 24 |
vmmc-supply = <®_cldo2>; |
| 25 |
vqmmc-supply = <®_bldo3>; |
| 26 |
mmc-pwrseq = <&wifi_pwrseq>; |
| 27 |
bus-width = <4>; |
| 28 |
non-removable; |
| 29 |
status = "okay"; |
| 30 |
|
| 31 |
brcm: wifi@1 { |
| 32 |
reg = <1>; |
| 33 |
compatible = "brcm,bcm4329-fmac"; |
| 34 |
interrupt-parent = <&r_pio>; |
| 35 |
interrupts = <1 0 IRQ_TYPE_LEVEL_LOW>; /* PM0 */ |
| 36 |
interrupt-names = "host-wake"; |
| 37 |
}; |
| 38 |
}; |
| 39 |
|
| 40 |
®_cldo2 { |
| 41 |
/* |
| 42 |
* This regulator is connected with CLDO3. |
| 43 |
* Before the kernel can support synchronized |
| 44 |
* enable of coupled regulators, keep them |
| 45 |
* both always on as a ugly hack. |
| 46 |
*/ |
| 47 |
regulator-always-on; |
| 48 |
}; |
| 49 |
|
| 50 |
®_cldo3 { |
| 51 |
/* |
| 52 |
* This regulator is connected with CLDO2. |
| 53 |
* See the comments for CLDO2. |
| 54 |
*/ |
| 55 |
regulator-always-on; |
| 56 |
}; |
| 57 |
|
| 58 |
/* There's the BT part of the AP6255 connected to that UART */ |
| 59 |
&uart1 { |
| 60 |
pinctrl-names = "default"; |
| 61 |
pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; |
| 62 |
uart-has-rtscts; |
| 63 |
status = "okay"; |
| 64 |
|
| 65 |
bluetooth { |
| 66 |
compatible = "brcm,bcm4345c5"; |
| 67 |
clocks = <&rtc CLK_OSC32K_FANOUT>; |
| 68 |
clock-names = "lpo"; |
| 69 |
device-wakeup-gpios = <&r_pio 1 2 GPIO_ACTIVE_HIGH>; /* PM2 */ |
| 70 |
host-wakeup-gpios = <&r_pio 1 1 GPIO_ACTIVE_HIGH>; /* PM1 */ |
| 71 |
shutdown-gpios = <&r_pio 1 4 GPIO_ACTIVE_HIGH>; /* PM4 */ |
| 72 |
max-speed = <1500000>; |
| 73 |
}; |
| 74 |
}; |