Debian Codegraph @

scripts/dtc/include-prefixes/arm64/allwinner/sun50i-h6-beelink-gs1.dts

raw
1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2 // Copyright (C) 2019 Clément Péron <[email protected]>
3
4 /dts-v1/;
5
6 #include "sun50i-h6.dtsi"
7 #include "sun50i-h6-cpu-opp.dtsi"
8 #include "sun50i-h6-gpu-opp.dtsi"
9
10 #include <dt-bindings/gpio/gpio.h>
11
12 / {
13 model = "Beelink GS1";
14 compatible = "azw,beelink-gs1", "allwinner,sun50i-h6";
15
16 aliases {
17 ethernet0 = &emac;
18 serial0 = &uart0;
19 };
20
21 chosen {
22 stdout-path = "serial0:115200n8";
23 };
24
25 connector {
26 compatible = "hdmi-connector";
27 type = "a";
28 ddc-en-gpios = <&pio 7 2 GPIO_ACTIVE_HIGH>; /* PH2 */
29
30 port {
31 hdmi_con_in: endpoint {
32 remote-endpoint = <&hdmi_out_con>;
33 };
34 };
35 };
36
37 ext_osc32k: ext-osc32k-clk {
38 #clock-cells = <0>;
39 compatible = "fixed-clock";
40 clock-frequency = <32768>;
41 clock-output-names = "ext_osc32k";
42 };
43
44 leds {
45 compatible = "gpio-leds";
46
47 led {
48 label = "beelink:white:power";
49 gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
50 default-state = "on";
51 };
52 };
53
54 reg_vcc5v: vcc5v {
55 /* board wide 5V supply directly from the DC jack */
56 compatible = "regulator-fixed";
57 regulator-name = "vcc-5v";
58 regulator-min-microvolt = <5000000>;
59 regulator-max-microvolt = <5000000>;
60 regulator-always-on;
61 };
62
63 sound-spdif {
64 compatible = "simple-audio-card";
65 simple-audio-card,name = "sun50i-h6-spdif";
66
67 simple-audio-card,cpu {
68 sound-dai = <&spdif>;
69 };
70
71 simple-audio-card,codec {
72 sound-dai = <&spdif_out>;
73 };
74 };
75
76 spdif_out: spdif-out {
77 #sound-dai-cells = <0>;
78 compatible = "linux,spdif-dit";
79 };
80 };
81
82 &cpu0 {
83 cpu-supply = <&reg_dcdca>;
84 };
85
86 &de {
87 status = "okay";
88 };
89
90 &dwc3 {
91 status = "okay";
92 };
93
94 &ehci0 {
95 status = "okay";
96 };
97
98 &emac {
99 pinctrl-names = "default";
100 pinctrl-0 = <&ext_rgmii_pins>;
101 phy-mode = "rgmii-id";
102 phy-handle = <&ext_rgmii_phy>;
103 phy-supply = <&reg_aldo2>;
104 status = "okay";
105 };
106
107 &gpu {
108 mali-supply = <&reg_dcdcc>;
109 status = "okay";
110 };
111
112 &hdmi {
113 status = "okay";
114 };
115
116 &hdmi_out {
117 hdmi_out_con: endpoint {
118 remote-endpoint = <&hdmi_con_in>;
119 };
120 };
121
122 &mdio {
123 ext_rgmii_phy: ethernet-phy@1 {
124 compatible = "ethernet-phy-ieee802.3-c22";
125 reg = <1>;
126 };
127 };
128
129 &mmc0 {
130 vmmc-supply = <&reg_cldo1>;
131 cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
132 disable-wp;
133 bus-width = <4>;
134 status = "okay";
135 };
136
137 &mmc2 {
138 vmmc-supply = <&reg_cldo1>;
139 vqmmc-supply = <&reg_bldo2>;
140 non-removable;
141 cap-mmc-hw-reset;
142 bus-width = <8>;
143 status = "okay";
144 };
145
146 &ohci0 {
147 status = "okay";
148 };
149
150 &pio {
151 vcc-pd-supply = <&reg_cldo1>;
152 vcc-pg-supply = <&reg_aldo1>;
153 };
154
155 &r_i2c {
156 status = "okay";
157
158 axp805: pmic@36 {
159 compatible = "x-powers,axp805", "x-powers,axp806";
160 reg = <0x36>;
161 interrupt-parent = <&r_intc>;
162 interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_LOW>;
163 interrupt-controller;
164 #interrupt-cells = <1>;
165 x-powers,self-working-mode;
166 vina-supply = <&reg_vcc5v>;
167 vinb-supply = <&reg_vcc5v>;
168 vinc-supply = <&reg_vcc5v>;
169 vind-supply = <&reg_vcc5v>;
170 vine-supply = <&reg_vcc5v>;
171 aldoin-supply = <&reg_vcc5v>;
172 bldoin-supply = <&reg_vcc5v>;
173 cldoin-supply = <&reg_vcc5v>;
174
175 regulators {
176 reg_aldo1: aldo1 {
177 regulator-always-on;
178 regulator-min-microvolt = <3300000>;
179 regulator-max-microvolt = <3300000>;
180 regulator-name = "vcc-pl";
181 };
182
183 reg_aldo2: aldo2 {
184 regulator-min-microvolt = <3300000>;
185 regulator-max-microvolt = <3300000>;
186 regulator-name = "vcc-ac200";
187 regulator-enable-ramp-delay = <100000>;
188 };
189
190 reg_aldo3: aldo3 {
191 regulator-always-on;
192 regulator-min-microvolt = <3300000>;
193 regulator-max-microvolt = <3300000>;
194 regulator-name = "vcc25-dram";
195 };
196
197 reg_bldo1: bldo1 {
198 regulator-always-on;
199 regulator-min-microvolt = <1800000>;
200 regulator-max-microvolt = <1800000>;
201 regulator-name = "vcc-bias-pll";
202 };
203
204 reg_bldo2: bldo2 {
205 regulator-always-on;
206 regulator-min-microvolt = <1800000>;
207 regulator-max-microvolt = <1800000>;
208 regulator-name = "vcc-efuse-pcie-hdmi-io";
209 };
210
211 reg_bldo3: bldo3 {
212 regulator-always-on;
213 regulator-min-microvolt = <1800000>;
214 regulator-max-microvolt = <1800000>;
215 regulator-name = "vcc-dcxoio";
216 };
217
218 bldo4 {
219 /* unused */
220 };
221
222 reg_cldo1: cldo1 {
223 regulator-always-on;
224 regulator-min-microvolt = <3300000>;
225 regulator-max-microvolt = <3300000>;
226 regulator-name = "vcc-3v3";
227 };
228
229 reg_cldo2: cldo2 {
230 regulator-min-microvolt = <3300000>;
231 regulator-max-microvolt = <3300000>;
232 regulator-name = "vcc-wifi-1";
233 };
234
235 reg_cldo3: cldo3 {
236 regulator-min-microvolt = <3300000>;
237 regulator-max-microvolt = <3300000>;
238 regulator-name = "vcc-wifi-2";
239 };
240
241 reg_dcdca: dcdca {
242 regulator-always-on;
243 regulator-min-microvolt = <810000>;
244 regulator-max-microvolt = <1160000>;
245 regulator-ramp-delay = <2500>;
246 regulator-name = "vdd-cpu";
247 };
248
249 reg_dcdcc: dcdcc {
250 regulator-enable-ramp-delay = <32000>;
251 regulator-min-microvolt = <810000>;
252 regulator-max-microvolt = <1080000>;
253 regulator-ramp-delay = <2500>;
254 regulator-name = "vdd-gpu";
255 };
256
257 reg_dcdcd: dcdcd {
258 regulator-always-on;
259 regulator-min-microvolt = <960000>;
260 regulator-max-microvolt = <960000>;
261 regulator-name = "vdd-sys";
262 };
263
264 reg_dcdce: dcdce {
265 regulator-always-on;
266 regulator-min-microvolt = <1200000>;
267 regulator-max-microvolt = <1200000>;
268 regulator-name = "vcc-dram";
269 };
270
271 sw {
272 /* unused */
273 };
274 };
275 };
276 };
277
278 &r_ir {
279 linux,rc-map-name = "rc-beelink-gs1";
280 status = "okay";
281 };
282
283 &r_pio {
284 /*
285 * PL0 and PL1 are used for PMIC I2C
286 * don't enable the pl-supply else
287 * it will fail at boot
288 *
289 * vcc-pl-supply = <&reg_aldo1>;
290 */
291 vcc-pm-supply = <&reg_aldo1>;
292 };
293
294 &spdif {
295 pinctrl-names = "default";
296 pinctrl-0 = <&spdif_tx_pin>;
297 status = "okay";
298 };
299
300 &uart0 {
301 pinctrl-names = "default";
302 pinctrl-0 = <&uart0_ph_pins>;
303 status = "okay";
304 };
305
306 &usb2otg {
307 dr_mode = "host";
308 status = "okay";
309 };
310
311 &usb2phy {
312 usb0_vbus-supply = <&reg_vcc5v>;
313 status = "okay";
314 };
315
316 &usb3phy {
317 status = "okay";
318 };