| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
// Copyright (C) 2017 Jagan Teki <[email protected]> |
| 3 |
|
| 4 |
/dts-v1/; |
| 5 |
|
| 6 |
#include "sun50i-h5.dtsi" |
| 7 |
|
| 8 |
#include <dt-bindings/gpio/gpio.h> |
| 9 |
|
| 10 |
/ { |
| 11 |
model = "OrangePi Zero Plus2"; |
| 12 |
compatible = "xunlong,orangepi-zero-plus2", "allwinner,sun50i-h5"; |
| 13 |
|
| 14 |
aliases { |
| 15 |
serial0 = &uart0; |
| 16 |
}; |
| 17 |
|
| 18 |
chosen { |
| 19 |
stdout-path = "serial0:115200n8"; |
| 20 |
}; |
| 21 |
|
| 22 |
connector { |
| 23 |
compatible = "hdmi-connector"; |
| 24 |
type = "a"; |
| 25 |
|
| 26 |
port { |
| 27 |
hdmi_con_in: endpoint { |
| 28 |
remote-endpoint = <&hdmi_out_con>; |
| 29 |
}; |
| 30 |
}; |
| 31 |
}; |
| 32 |
|
| 33 |
leds { |
| 34 |
compatible = "gpio-leds"; |
| 35 |
|
| 36 |
led-0 { |
| 37 |
label = "orangepi:green:pwr"; |
| 38 |
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; |
| 39 |
default-state = "on"; |
| 40 |
}; |
| 41 |
|
| 42 |
led-1 { |
| 43 |
label = "orangepi:red:status"; |
| 44 |
gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; |
| 45 |
}; |
| 46 |
}; |
| 47 |
|
| 48 |
reg_vcc3v3: vcc3v3 { |
| 49 |
compatible = "regulator-fixed"; |
| 50 |
regulator-name = "vcc3v3"; |
| 51 |
regulator-min-microvolt = <3300000>; |
| 52 |
regulator-max-microvolt = <3300000>; |
| 53 |
}; |
| 54 |
|
| 55 |
wifi_pwrseq: pwrseq { |
| 56 |
compatible = "mmc-pwrseq-simple"; |
| 57 |
reset-gpios = <&pio 0 9 GPIO_ACTIVE_LOW>; /* PA9 */ |
| 58 |
post-power-on-delay-ms = <200>; |
| 59 |
}; |
| 60 |
}; |
| 61 |
|
| 62 |
&de { |
| 63 |
status = "okay"; |
| 64 |
}; |
| 65 |
|
| 66 |
&ehci0 { |
| 67 |
status = "okay"; |
| 68 |
}; |
| 69 |
|
| 70 |
&hdmi { |
| 71 |
status = "okay"; |
| 72 |
}; |
| 73 |
|
| 74 |
&hdmi_out { |
| 75 |
hdmi_out_con: endpoint { |
| 76 |
remote-endpoint = <&hdmi_con_in>; |
| 77 |
}; |
| 78 |
}; |
| 79 |
|
| 80 |
&mmc0 { |
| 81 |
vmmc-supply = <®_vcc3v3>; |
| 82 |
disable-wp; |
| 83 |
bus-width = <4>; |
| 84 |
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; |
| 85 |
status = "okay"; |
| 86 |
}; |
| 87 |
|
| 88 |
&mmc1 { |
| 89 |
vmmc-supply = <®_vcc3v3>; |
| 90 |
vqmmc-supply = <®_vcc3v3>; |
| 91 |
mmc-pwrseq = <&wifi_pwrseq>; |
| 92 |
bus-width = <4>; |
| 93 |
non-removable; |
| 94 |
status = "okay"; |
| 95 |
|
| 96 |
brcmf: wifi@1 { |
| 97 |
reg = <1>; |
| 98 |
compatible = "brcm,bcm4329-fmac"; |
| 99 |
interrupt-parent = <&r_pio>; |
| 100 |
interrupts = <0 7 IRQ_TYPE_LEVEL_LOW>; /* PL7 */ |
| 101 |
interrupt-names = "host-wake"; |
| 102 |
}; |
| 103 |
}; |
| 104 |
|
| 105 |
&mmc2 { |
| 106 |
pinctrl-names = "default"; |
| 107 |
pinctrl-0 = <&mmc2_8bit_pins>; |
| 108 |
vmmc-supply = <®_vcc3v3>; |
| 109 |
bus-width = <8>; |
| 110 |
non-removable; |
| 111 |
cap-mmc-hw-reset; |
| 112 |
status = "okay"; |
| 113 |
}; |
| 114 |
|
| 115 |
&ohci0 { |
| 116 |
status = "okay"; |
| 117 |
}; |
| 118 |
|
| 119 |
&uart0 { |
| 120 |
pinctrl-names = "default"; |
| 121 |
pinctrl-0 = <&uart0_pa_pins>; |
| 122 |
status = "okay"; |
| 123 |
}; |
| 124 |
|
| 125 |
&uart1 { |
| 126 |
pinctrl-names = "default"; |
| 127 |
pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>; |
| 128 |
status = "okay"; |
| 129 |
}; |
| 130 |
|
| 131 |
&usb_otg { |
| 132 |
/* |
| 133 |
* According to schematics CN1 MicroUSB port can be used to take |
| 134 |
* external 5V to power up the board VBUS. On the contrary CN1 MicroUSB |
| 135 |
* port cannot provide power externally even if the board is powered |
| 136 |
* via GPIO pins. It thus makes sense to force peripheral mode. |
| 137 |
*/ |
| 138 |
dr_mode = "peripheral"; |
| 139 |
status = "okay"; |
| 140 |
}; |
| 141 |
|
| 142 |
&usbphy { |
| 143 |
status = "okay"; |
| 144 |
}; |