| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
// Copyright (C) 2016 ARM Ltd. |
| 3 |
// Copyright (C) 2018 Hauke Mehrtens <[email protected]> |
| 4 |
|
| 5 |
/dts-v1/; |
| 6 |
#include "sun50i-h5.dtsi" |
| 7 |
|
| 8 |
#include <dt-bindings/gpio/gpio.h> |
| 9 |
#include <dt-bindings/input/input.h> |
| 10 |
#include <dt-bindings/pinctrl/sun4i-a10.h> |
| 11 |
|
| 12 |
/ { |
| 13 |
model = "Xunlong Orange Pi Zero Plus"; |
| 14 |
compatible = "xunlong,orangepi-zero-plus", "allwinner,sun50i-h5"; |
| 15 |
|
| 16 |
reg_vcc3v3: vcc3v3 { |
| 17 |
compatible = "regulator-fixed"; |
| 18 |
regulator-name = "vcc3v3"; |
| 19 |
regulator-min-microvolt = <3300000>; |
| 20 |
regulator-max-microvolt = <3300000>; |
| 21 |
}; |
| 22 |
|
| 23 |
aliases { |
| 24 |
ethernet0 = &emac; |
| 25 |
ethernet1 = &rtl8189ftv; |
| 26 |
serial0 = &uart0; |
| 27 |
}; |
| 28 |
|
| 29 |
chosen { |
| 30 |
stdout-path = "serial0:115200n8"; |
| 31 |
}; |
| 32 |
|
| 33 |
leds { |
| 34 |
compatible = "gpio-leds"; |
| 35 |
|
| 36 |
led-0 { |
| 37 |
label = "orangepi:green:pwr"; |
| 38 |
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */ |
| 39 |
default-state = "on"; |
| 40 |
}; |
| 41 |
|
| 42 |
led-1 { |
| 43 |
label = "orangepi:red:status"; |
| 44 |
gpios = <&pio 0 17 GPIO_ACTIVE_HIGH>; /* PA17 */ |
| 45 |
}; |
| 46 |
}; |
| 47 |
|
| 48 |
reg_gmac_3v3: gmac-3v3 { |
| 49 |
compatible = "regulator-fixed"; |
| 50 |
regulator-name = "gmac-3v3"; |
| 51 |
regulator-min-microvolt = <3300000>; |
| 52 |
regulator-max-microvolt = <3300000>; |
| 53 |
startup-delay-us = <100000>; |
| 54 |
enable-active-high; |
| 55 |
gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */ |
| 56 |
}; |
| 57 |
}; |
| 58 |
|
| 59 |
&ehci0 { |
| 60 |
status = "okay"; |
| 61 |
}; |
| 62 |
|
| 63 |
&ehci1 { |
| 64 |
status = "okay"; |
| 65 |
}; |
| 66 |
|
| 67 |
&emac { |
| 68 |
pinctrl-names = "default"; |
| 69 |
pinctrl-0 = <&emac_rgmii_pins>; |
| 70 |
phy-supply = <®_gmac_3v3>; |
| 71 |
phy-handle = <&ext_rgmii_phy>; |
| 72 |
phy-mode = "rgmii-id"; |
| 73 |
status = "okay"; |
| 74 |
}; |
| 75 |
|
| 76 |
&external_mdio { |
| 77 |
ext_rgmii_phy: ethernet-phy@1 { |
| 78 |
compatible = "ethernet-phy-ieee802.3-c22"; |
| 79 |
reg = <1>; |
| 80 |
}; |
| 81 |
}; |
| 82 |
|
| 83 |
&mmc0 { |
| 84 |
vmmc-supply = <®_vcc3v3>; |
| 85 |
disable-wp; |
| 86 |
bus-width = <4>; |
| 87 |
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ |
| 88 |
status = "okay"; |
| 89 |
}; |
| 90 |
|
| 91 |
&mmc1 { |
| 92 |
vmmc-supply = <®_vcc3v3>; |
| 93 |
bus-width = <4>; |
| 94 |
non-removable; |
| 95 |
status = "okay"; |
| 96 |
|
| 97 |
/* |
| 98 |
* Explicitly define the sdio device, so that we can add an ethernet |
| 99 |
* alias for it (which e.g. makes u-boot set a mac-address). |
| 100 |
*/ |
| 101 |
rtl8189ftv: wifi@1 { |
| 102 |
reg = <1>; |
| 103 |
}; |
| 104 |
}; |
| 105 |
|
| 106 |
&spi0 { |
| 107 |
status = "okay"; |
| 108 |
|
| 109 |
flash@0 { |
| 110 |
#address-cells = <1>; |
| 111 |
#size-cells = <1>; |
| 112 |
compatible = "mxicy,mx25l1606e", "winbond,w25q128"; |
| 113 |
reg = <0>; |
| 114 |
spi-max-frequency = <40000000>; |
| 115 |
}; |
| 116 |
}; |
| 117 |
|
| 118 |
&ohci0 { |
| 119 |
status = "okay"; |
| 120 |
}; |
| 121 |
|
| 122 |
&ohci1 { |
| 123 |
status = "okay"; |
| 124 |
}; |
| 125 |
|
| 126 |
&uart0 { |
| 127 |
pinctrl-names = "default"; |
| 128 |
pinctrl-0 = <&uart0_pa_pins>; |
| 129 |
status = "okay"; |
| 130 |
}; |
| 131 |
|
| 132 |
&usb_otg { |
| 133 |
dr_mode = "peripheral"; |
| 134 |
status = "okay"; |
| 135 |
}; |
| 136 |
|
| 137 |
&usbphy { |
| 138 |
/* USB Type-A ports' VBUS is always on */ |
| 139 |
usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ |
| 140 |
status = "okay"; |
| 141 |
}; |