| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
// Copyright (C) 2017 Icenowy Zheng <[email protected]> |
| 3 |
// Based on sun50i-h5-orangepi-pc2.dts, which is: |
| 4 |
// Copyright (C) 2016 ARM Ltd. |
| 5 |
|
| 6 |
/dts-v1/; |
| 7 |
#include "sun50i-h5.dtsi" |
| 8 |
|
| 9 |
#include <dt-bindings/gpio/gpio.h> |
| 10 |
#include <dt-bindings/input/input.h> |
| 11 |
|
| 12 |
/ { |
| 13 |
model = "Xunlong Orange Pi Prime"; |
| 14 |
compatible = "xunlong,orangepi-prime", "allwinner,sun50i-h5"; |
| 15 |
|
| 16 |
aliases { |
| 17 |
ethernet0 = &emac; |
| 18 |
serial0 = &uart0; |
| 19 |
}; |
| 20 |
|
| 21 |
chosen { |
| 22 |
stdout-path = "serial0:115200n8"; |
| 23 |
}; |
| 24 |
|
| 25 |
connector { |
| 26 |
compatible = "hdmi-connector"; |
| 27 |
type = "a"; |
| 28 |
|
| 29 |
port { |
| 30 |
hdmi_con_in: endpoint { |
| 31 |
remote-endpoint = <&hdmi_out_con>; |
| 32 |
}; |
| 33 |
}; |
| 34 |
}; |
| 35 |
|
| 36 |
leds { |
| 37 |
compatible = "gpio-leds"; |
| 38 |
|
| 39 |
led-0 { |
| 40 |
label = "orangepi:green:pwr"; |
| 41 |
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; |
| 42 |
default-state = "on"; |
| 43 |
}; |
| 44 |
|
| 45 |
led-1 { |
| 46 |
label = "orangepi:red:status"; |
| 47 |
gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>; |
| 48 |
}; |
| 49 |
}; |
| 50 |
|
| 51 |
gpio-keys { |
| 52 |
compatible = "gpio-keys"; |
| 53 |
|
| 54 |
key-sw4 { |
| 55 |
label = "sw4"; |
| 56 |
linux,code = <BTN_0>; |
| 57 |
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; |
| 58 |
}; |
| 59 |
}; |
| 60 |
|
| 61 |
reg_gmac_3v3: gmac-3v3 { |
| 62 |
compatible = "regulator-fixed"; |
| 63 |
regulator-name = "gmac-3v3"; |
| 64 |
regulator-min-microvolt = <3300000>; |
| 65 |
regulator-max-microvolt = <3300000>; |
| 66 |
startup-delay-us = <100000>; |
| 67 |
enable-active-high; |
| 68 |
gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; |
| 69 |
}; |
| 70 |
|
| 71 |
reg_vcc3v3: vcc3v3 { |
| 72 |
compatible = "regulator-fixed"; |
| 73 |
regulator-name = "vcc3v3"; |
| 74 |
regulator-min-microvolt = <3300000>; |
| 75 |
regulator-max-microvolt = <3300000>; |
| 76 |
}; |
| 77 |
|
| 78 |
reg_usb0_vbus: usb0-vbus { |
| 79 |
compatible = "regulator-fixed"; |
| 80 |
regulator-name = "usb0-vbus"; |
| 81 |
regulator-min-microvolt = <5000000>; |
| 82 |
regulator-max-microvolt = <5000000>; |
| 83 |
enable-active-high; |
| 84 |
gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */ |
| 85 |
status = "okay"; |
| 86 |
}; |
| 87 |
|
| 88 |
wifi_pwrseq: pwrseq { |
| 89 |
compatible = "mmc-pwrseq-simple"; |
| 90 |
reset-gpios = <&pio 2 14 GPIO_ACTIVE_LOW>; /* PC14 */ |
| 91 |
}; |
| 92 |
}; |
| 93 |
|
| 94 |
&codec { |
| 95 |
allwinner,audio-routing = |
| 96 |
"Line Out", "LINEOUT", |
| 97 |
"MIC1", "Mic", |
| 98 |
"Mic", "MBIAS"; |
| 99 |
status = "okay"; |
| 100 |
}; |
| 101 |
|
| 102 |
&de { |
| 103 |
status = "okay"; |
| 104 |
}; |
| 105 |
|
| 106 |
&ehci0 { |
| 107 |
status = "okay"; |
| 108 |
}; |
| 109 |
|
| 110 |
&ehci1 { |
| 111 |
status = "okay"; |
| 112 |
}; |
| 113 |
|
| 114 |
&ehci2 { |
| 115 |
status = "okay"; |
| 116 |
}; |
| 117 |
|
| 118 |
&ehci3 { |
| 119 |
status = "okay"; |
| 120 |
}; |
| 121 |
|
| 122 |
&emac { |
| 123 |
pinctrl-names = "default"; |
| 124 |
pinctrl-0 = <&emac_rgmii_pins>; |
| 125 |
phy-supply = <®_gmac_3v3>; |
| 126 |
phy-handle = <&ext_rgmii_phy>; |
| 127 |
phy-mode = "rgmii-id"; |
| 128 |
status = "okay"; |
| 129 |
}; |
| 130 |
|
| 131 |
&external_mdio { |
| 132 |
ext_rgmii_phy: ethernet-phy@1 { |
| 133 |
compatible = "ethernet-phy-ieee802.3-c22"; |
| 134 |
reg = <1>; |
| 135 |
}; |
| 136 |
}; |
| 137 |
|
| 138 |
&hdmi { |
| 139 |
status = "okay"; |
| 140 |
}; |
| 141 |
|
| 142 |
&hdmi_out { |
| 143 |
hdmi_out_con: endpoint { |
| 144 |
remote-endpoint = <&hdmi_con_in>; |
| 145 |
}; |
| 146 |
}; |
| 147 |
|
| 148 |
&ir { |
| 149 |
pinctrl-names = "default"; |
| 150 |
pinctrl-0 = <&r_ir_rx_pin>; |
| 151 |
status = "okay"; |
| 152 |
}; |
| 153 |
|
| 154 |
&mmc0 { |
| 155 |
vmmc-supply = <®_vcc3v3>; |
| 156 |
disable-wp; |
| 157 |
bus-width = <4>; |
| 158 |
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ |
| 159 |
status = "okay"; |
| 160 |
}; |
| 161 |
|
| 162 |
&mmc1 { |
| 163 |
vmmc-supply = <®_vcc3v3>; |
| 164 |
mmc-pwrseq = <&wifi_pwrseq>; |
| 165 |
bus-width = <4>; |
| 166 |
non-removable; |
| 167 |
status = "okay"; |
| 168 |
}; |
| 169 |
|
| 170 |
&ohci0 { |
| 171 |
status = "okay"; |
| 172 |
}; |
| 173 |
|
| 174 |
&ohci1 { |
| 175 |
status = "okay"; |
| 176 |
}; |
| 177 |
|
| 178 |
&ohci2 { |
| 179 |
status = "okay"; |
| 180 |
}; |
| 181 |
|
| 182 |
&ohci3 { |
| 183 |
status = "okay"; |
| 184 |
}; |
| 185 |
|
| 186 |
&uart0 { |
| 187 |
pinctrl-names = "default"; |
| 188 |
pinctrl-0 = <&uart0_pa_pins>; |
| 189 |
status = "okay"; |
| 190 |
}; |
| 191 |
|
| 192 |
&uart1 { |
| 193 |
pinctrl-names = "default"; |
| 194 |
pinctrl-0 = <&uart1_pins>; |
| 195 |
status = "disabled"; |
| 196 |
}; |
| 197 |
|
| 198 |
&uart2 { |
| 199 |
pinctrl-names = "default"; |
| 200 |
pinctrl-0 = <&uart2_pins>; |
| 201 |
status = "disabled"; |
| 202 |
}; |
| 203 |
|
| 204 |
&usb_otg { |
| 205 |
dr_mode = "otg"; |
| 206 |
status = "okay"; |
| 207 |
}; |
| 208 |
|
| 209 |
&usbphy { |
| 210 |
/* USB Type-A ports' VBUS is always on */ |
| 211 |
usb0_id_det-gpios = <&pio 0 21 GPIO_ACTIVE_HIGH>; /* PA21 */ |
| 212 |
usb0_vbus-supply = <®_usb0_vbus>; |
| 213 |
status = "okay"; |
| 214 |
}; |