| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
// Copyright (C) 2016 ARM Ltd. |
| 3 |
|
| 4 |
/dts-v1/; |
| 5 |
#include "sun50i-h5.dtsi" |
| 6 |
#include "sun50i-h5-cpu-opp.dtsi" |
| 7 |
|
| 8 |
#include <dt-bindings/gpio/gpio.h> |
| 9 |
#include <dt-bindings/input/input.h> |
| 10 |
#include <dt-bindings/pinctrl/sun4i-a10.h> |
| 11 |
|
| 12 |
/ { |
| 13 |
model = "Xunlong Orange Pi PC 2"; |
| 14 |
compatible = "xunlong,orangepi-pc2", "allwinner,sun50i-h5"; |
| 15 |
|
| 16 |
reg_vcc3v3: vcc3v3 { |
| 17 |
compatible = "regulator-fixed"; |
| 18 |
regulator-name = "vcc3v3"; |
| 19 |
regulator-min-microvolt = <3300000>; |
| 20 |
regulator-max-microvolt = <3300000>; |
| 21 |
}; |
| 22 |
|
| 23 |
aliases { |
| 24 |
ethernet0 = &emac; |
| 25 |
serial0 = &uart0; |
| 26 |
}; |
| 27 |
|
| 28 |
chosen { |
| 29 |
stdout-path = "serial0:115200n8"; |
| 30 |
}; |
| 31 |
|
| 32 |
connector { |
| 33 |
compatible = "hdmi-connector"; |
| 34 |
type = "a"; |
| 35 |
|
| 36 |
port { |
| 37 |
hdmi_con_in: endpoint { |
| 38 |
remote-endpoint = <&hdmi_out_con>; |
| 39 |
}; |
| 40 |
}; |
| 41 |
}; |
| 42 |
|
| 43 |
leds { |
| 44 |
compatible = "gpio-leds"; |
| 45 |
|
| 46 |
led-0 { |
| 47 |
label = "orangepi:green:pwr"; |
| 48 |
gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; |
| 49 |
default-state = "on"; |
| 50 |
}; |
| 51 |
|
| 52 |
led-1 { |
| 53 |
label = "orangepi:red:status"; |
| 54 |
gpios = <&pio 0 20 GPIO_ACTIVE_HIGH>; |
| 55 |
}; |
| 56 |
}; |
| 57 |
|
| 58 |
gpio-keys { |
| 59 |
compatible = "gpio-keys"; |
| 60 |
|
| 61 |
key-sw4 { |
| 62 |
label = "sw4"; |
| 63 |
linux,code = <BTN_0>; |
| 64 |
gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>; |
| 65 |
wakeup-source; |
| 66 |
}; |
| 67 |
}; |
| 68 |
|
| 69 |
reg_gmac_3v3: gmac-3v3 { |
| 70 |
compatible = "regulator-fixed"; |
| 71 |
regulator-name = "gmac-3v3"; |
| 72 |
regulator-min-microvolt = <3300000>; |
| 73 |
regulator-max-microvolt = <3300000>; |
| 74 |
startup-delay-us = <100000>; |
| 75 |
enable-active-high; |
| 76 |
gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; |
| 77 |
}; |
| 78 |
|
| 79 |
reg_usb0_vbus: usb0-vbus { |
| 80 |
compatible = "regulator-fixed"; |
| 81 |
regulator-name = "usb0-vbus"; |
| 82 |
regulator-min-microvolt = <5000000>; |
| 83 |
regulator-max-microvolt = <5000000>; |
| 84 |
enable-active-high; |
| 85 |
gpio = <&r_pio 0 2 GPIO_ACTIVE_HIGH>; /* PL2 */ |
| 86 |
status = "okay"; |
| 87 |
}; |
| 88 |
}; |
| 89 |
|
| 90 |
&codec { |
| 91 |
allwinner,audio-routing = |
| 92 |
"Line Out", "LINEOUT", |
| 93 |
"MIC1", "Mic", |
| 94 |
"Mic", "MBIAS"; |
| 95 |
status = "okay"; |
| 96 |
}; |
| 97 |
|
| 98 |
&cpu0 { |
| 99 |
cpu-supply = <®_vdd_cpux>; |
| 100 |
}; |
| 101 |
|
| 102 |
&de { |
| 103 |
status = "okay"; |
| 104 |
}; |
| 105 |
|
| 106 |
&ehci0 { |
| 107 |
status = "okay"; |
| 108 |
}; |
| 109 |
|
| 110 |
&ehci1 { |
| 111 |
status = "okay"; |
| 112 |
}; |
| 113 |
|
| 114 |
&ehci2 { |
| 115 |
status = "okay"; |
| 116 |
}; |
| 117 |
|
| 118 |
&ehci3 { |
| 119 |
status = "okay"; |
| 120 |
}; |
| 121 |
|
| 122 |
&emac { |
| 123 |
pinctrl-names = "default"; |
| 124 |
pinctrl-0 = <&emac_rgmii_pins>; |
| 125 |
phy-supply = <®_gmac_3v3>; |
| 126 |
phy-handle = <&ext_rgmii_phy>; |
| 127 |
phy-mode = "rgmii-id"; |
| 128 |
status = "okay"; |
| 129 |
}; |
| 130 |
|
| 131 |
&external_mdio { |
| 132 |
ext_rgmii_phy: ethernet-phy@1 { |
| 133 |
compatible = "ethernet-phy-ieee802.3-c22"; |
| 134 |
reg = <1>; |
| 135 |
}; |
| 136 |
}; |
| 137 |
|
| 138 |
&hdmi { |
| 139 |
status = "okay"; |
| 140 |
}; |
| 141 |
|
| 142 |
&hdmi_out { |
| 143 |
hdmi_out_con: endpoint { |
| 144 |
remote-endpoint = <&hdmi_con_in>; |
| 145 |
}; |
| 146 |
}; |
| 147 |
|
| 148 |
&ir { |
| 149 |
pinctrl-names = "default"; |
| 150 |
pinctrl-0 = <&r_ir_rx_pin>; |
| 151 |
status = "okay"; |
| 152 |
}; |
| 153 |
|
| 154 |
&mmc0 { |
| 155 |
vmmc-supply = <®_vcc3v3>; |
| 156 |
disable-wp; |
| 157 |
bus-width = <4>; |
| 158 |
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */ |
| 159 |
status = "okay"; |
| 160 |
}; |
| 161 |
|
| 162 |
&ohci0 { |
| 163 |
status = "okay"; |
| 164 |
}; |
| 165 |
|
| 166 |
&ohci1 { |
| 167 |
status = "okay"; |
| 168 |
}; |
| 169 |
|
| 170 |
&ohci2 { |
| 171 |
status = "okay"; |
| 172 |
}; |
| 173 |
|
| 174 |
&ohci3 { |
| 175 |
status = "okay"; |
| 176 |
}; |
| 177 |
|
| 178 |
&r_i2c { |
| 179 |
status = "okay"; |
| 180 |
|
| 181 |
reg_vdd_cpux: regulator@65 { |
| 182 |
compatible = "silergy,sy8106a"; |
| 183 |
reg = <0x65>; |
| 184 |
regulator-name = "vdd-cpux"; |
| 185 |
silergy,fixed-microvolt = <1100000>; |
| 186 |
regulator-min-microvolt = <1000000>; |
| 187 |
regulator-max-microvolt = <1400000>; |
| 188 |
regulator-ramp-delay = <200>; |
| 189 |
regulator-boot-on; |
| 190 |
regulator-always-on; |
| 191 |
}; |
| 192 |
}; |
| 193 |
|
| 194 |
&spi0 { |
| 195 |
status = "okay"; |
| 196 |
|
| 197 |
flash@0 { |
| 198 |
#address-cells = <1>; |
| 199 |
#size-cells = <1>; |
| 200 |
compatible = "jedec,spi-nor"; |
| 201 |
reg = <0>; |
| 202 |
spi-max-frequency = <40000000>; |
| 203 |
}; |
| 204 |
}; |
| 205 |
|
| 206 |
&uart0 { |
| 207 |
pinctrl-names = "default"; |
| 208 |
pinctrl-0 = <&uart0_pa_pins>; |
| 209 |
status = "okay"; |
| 210 |
}; |
| 211 |
|
| 212 |
&uart1 { |
| 213 |
pinctrl-names = "default"; |
| 214 |
pinctrl-0 = <&uart1_pins>; |
| 215 |
status = "disabled"; |
| 216 |
}; |
| 217 |
|
| 218 |
&uart2 { |
| 219 |
pinctrl-names = "default"; |
| 220 |
pinctrl-0 = <&uart2_pins>; |
| 221 |
status = "disabled"; |
| 222 |
}; |
| 223 |
|
| 224 |
&usb_otg { |
| 225 |
dr_mode = "otg"; |
| 226 |
status = "okay"; |
| 227 |
}; |
| 228 |
|
| 229 |
&usbphy { |
| 230 |
/* USB Type-A ports' VBUS is always on */ |
| 231 |
usb0_id_det-gpios = <&pio 6 12 GPIO_ACTIVE_HIGH>; /* PG12 */ |
| 232 |
usb0_vbus-supply = <®_usb0_vbus>; |
| 233 |
status = "okay"; |
| 234 |
}; |