| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
/* |
| 3 |
* Copyright (C) 2019 Icenowy Zheng <[email protected]> |
| 4 |
* |
| 5 |
*/ |
| 6 |
|
| 7 |
/dts-v1/; |
| 8 |
|
| 9 |
#include "sun50i-a64.dtsi" |
| 10 |
#include "sun50i-a64-cpu-opp.dtsi" |
| 11 |
|
| 12 |
#include <dt-bindings/gpio/gpio.h> |
| 13 |
#include <dt-bindings/input/input.h> |
| 14 |
#include <dt-bindings/pwm/pwm.h> |
| 15 |
|
| 16 |
/ { |
| 17 |
model = "Pine64 PineTab Developer Sample"; |
| 18 |
compatible = "pine64,pinetab", "allwinner,sun50i-a64"; |
| 19 |
chassis-type = "tablet"; |
| 20 |
|
| 21 |
aliases { |
| 22 |
serial0 = &uart0; |
| 23 |
ethernet0 = &rtl8723cs; |
| 24 |
}; |
| 25 |
|
| 26 |
backlight: backlight { |
| 27 |
compatible = "pwm-backlight"; |
| 28 |
pwms = <&pwm 0 50000 PWM_POLARITY_INVERTED>; |
| 29 |
brightness-levels = <0 16 18 20 22 24 26 29 32 35 38 42 46 51 56 62 68 75 83 91 100>; |
| 30 |
default-brightness-level = <15>; |
| 31 |
enable-gpios = <&pio 3 23 GPIO_ACTIVE_HIGH>; /* PD23 */ |
| 32 |
power-supply = <&vdd_bl>; |
| 33 |
}; |
| 34 |
|
| 35 |
chosen { |
| 36 |
stdout-path = "serial0:115200n8"; |
| 37 |
}; |
| 38 |
|
| 39 |
hdmi-connector { |
| 40 |
compatible = "hdmi-connector"; |
| 41 |
type = "c"; |
| 42 |
|
| 43 |
port { |
| 44 |
hdmi_con_in: endpoint { |
| 45 |
remote-endpoint = <&hdmi_out_con>; |
| 46 |
}; |
| 47 |
}; |
| 48 |
}; |
| 49 |
|
| 50 |
i2c-csi { |
| 51 |
compatible = "i2c-gpio"; |
| 52 |
sda-gpios = <&pio 4 13 GPIO_ACTIVE_HIGH>; /* PE13 */ |
| 53 |
scl-gpios = <&pio 4 12 GPIO_ACTIVE_HIGH>; /* PE12 */ |
| 54 |
i2c-gpio,delay-us = <5>; |
| 55 |
#address-cells = <1>; |
| 56 |
#size-cells = <0>; |
| 57 |
|
| 58 |
/* Rear camera */ |
| 59 |
ov5640: camera@3c { |
| 60 |
compatible = "ovti,ov5640"; |
| 61 |
reg = <0x3c>; |
| 62 |
pinctrl-names = "default"; |
| 63 |
pinctrl-0 = <&csi_mclk_pin>; |
| 64 |
clocks = <&ccu CLK_CSI_MCLK>; |
| 65 |
clock-names = "xclk"; |
| 66 |
|
| 67 |
AVDD-supply = <®_dldo3>; |
| 68 |
DOVDD-supply = <®_aldo1>; |
| 69 |
DVDD-supply = <®_eldo3>; |
| 70 |
reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>; /* PE14 */ |
| 71 |
powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* PE15 */ |
| 72 |
|
| 73 |
port { |
| 74 |
ov5640_ep: endpoint { |
| 75 |
remote-endpoint = <&csi_ep>; |
| 76 |
bus-width = <8>; |
| 77 |
hsync-active = <1>; /* Active high */ |
| 78 |
vsync-active = <0>; /* Active low */ |
| 79 |
data-active = <1>; /* Active high */ |
| 80 |
pclk-sample = <1>; /* Rising */ |
| 81 |
}; |
| 82 |
}; |
| 83 |
}; |
| 84 |
}; |
| 85 |
|
| 86 |
speaker_amp: audio-amplifier { |
| 87 |
compatible = "simple-audio-amplifier"; |
| 88 |
enable-gpios = <&pio 7 7 GPIO_ACTIVE_HIGH>; /* PH7 */ |
| 89 |
sound-name-prefix = "Speaker Amp"; |
| 90 |
}; |
| 91 |
|
| 92 |
vdd_bl: regulator { |
| 93 |
compatible = "regulator-fixed"; |
| 94 |
regulator-name = "bl-3v3"; |
| 95 |
regulator-min-microvolt = <3300000>; |
| 96 |
regulator-max-microvolt = <3300000>; |
| 97 |
gpio = <&pio 7 6 GPIO_ACTIVE_HIGH>; /* PH6 */ |
| 98 |
enable-active-high; |
| 99 |
}; |
| 100 |
|
| 101 |
wifi_pwrseq: pwrseq { |
| 102 |
compatible = "mmc-pwrseq-simple"; |
| 103 |
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* PL2 */ |
| 104 |
post-power-on-delay-ms = <200>; |
| 105 |
}; |
| 106 |
}; |
| 107 |
|
| 108 |
&codec { |
| 109 |
status = "okay"; |
| 110 |
}; |
| 111 |
|
| 112 |
&codec_analog { |
| 113 |
cpvdd-supply = <®_eldo1>; |
| 114 |
status = "okay"; |
| 115 |
}; |
| 116 |
|
| 117 |
&cpu0 { |
| 118 |
cpu-supply = <®_dcdc2>; |
| 119 |
}; |
| 120 |
|
| 121 |
&cpu1 { |
| 122 |
cpu-supply = <®_dcdc2>; |
| 123 |
}; |
| 124 |
|
| 125 |
&cpu2 { |
| 126 |
cpu-supply = <®_dcdc2>; |
| 127 |
}; |
| 128 |
|
| 129 |
&cpu3 { |
| 130 |
cpu-supply = <®_dcdc2>; |
| 131 |
}; |
| 132 |
|
| 133 |
&csi { |
| 134 |
status = "okay"; |
| 135 |
|
| 136 |
port { |
| 137 |
csi_ep: endpoint { |
| 138 |
remote-endpoint = <&ov5640_ep>; |
| 139 |
bus-width = <8>; |
| 140 |
hsync-active = <1>; /* Active high */ |
| 141 |
vsync-active = <0>; /* Active low */ |
| 142 |
data-active = <1>; /* Active high */ |
| 143 |
pclk-sample = <1>; /* Rising */ |
| 144 |
}; |
| 145 |
}; |
| 146 |
}; |
| 147 |
|
| 148 |
&dai { |
| 149 |
status = "okay"; |
| 150 |
}; |
| 151 |
|
| 152 |
&de { |
| 153 |
status = "okay"; |
| 154 |
}; |
| 155 |
|
| 156 |
&dphy { |
| 157 |
status = "okay"; |
| 158 |
}; |
| 159 |
|
| 160 |
&dsi { |
| 161 |
vcc-dsi-supply = <®_dldo1>; |
| 162 |
status = "okay"; |
| 163 |
|
| 164 |
panel@0 { |
| 165 |
compatible = "feixin,k101-im2ba02"; |
| 166 |
reg = <0>; |
| 167 |
avdd-supply = <®_dc1sw>; |
| 168 |
dvdd-supply = <®_dc1sw>; |
| 169 |
cvdd-supply = <®_ldo_io1>; |
| 170 |
reset-gpios = <&pio 3 24 GPIO_ACTIVE_HIGH>; /* PD24 */ |
| 171 |
backlight = <&backlight>; |
| 172 |
}; |
| 173 |
}; |
| 174 |
|
| 175 |
&ehci0 { |
| 176 |
status = "okay"; |
| 177 |
}; |
| 178 |
|
| 179 |
&ehci1 { |
| 180 |
status = "okay"; |
| 181 |
}; |
| 182 |
|
| 183 |
&i2c0 { |
| 184 |
status = "okay"; |
| 185 |
|
| 186 |
touchscreen@5d { |
| 187 |
compatible = "goodix,gt9271"; |
| 188 |
reg = <0x5d>; |
| 189 |
interrupt-parent = <&pio>; |
| 190 |
interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */ |
| 191 |
irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ |
| 192 |
reset-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* PH8 */ |
| 193 |
AVDD28-supply = <®_ldo_io1>; |
| 194 |
}; |
| 195 |
}; |
| 196 |
|
| 197 |
&i2c0_pins { |
| 198 |
bias-pull-up; |
| 199 |
}; |
| 200 |
|
| 201 |
&i2c1 { |
| 202 |
status = "okay"; |
| 203 |
|
| 204 |
/* TODO: add Bochs BMA223 accelerometer here */ |
| 205 |
}; |
| 206 |
|
| 207 |
&lradc { |
| 208 |
vref-supply = <®_aldo3>; |
| 209 |
status = "okay"; |
| 210 |
|
| 211 |
button-200 { |
| 212 |
label = "Volume Up"; |
| 213 |
linux,code = <KEY_VOLUMEUP>; |
| 214 |
channel = <0>; |
| 215 |
voltage = <200000>; |
| 216 |
}; |
| 217 |
|
| 218 |
button-400 { |
| 219 |
label = "Volume Down"; |
| 220 |
linux,code = <KEY_VOLUMEDOWN>; |
| 221 |
channel = <0>; |
| 222 |
voltage = <400000>; |
| 223 |
}; |
| 224 |
}; |
| 225 |
|
| 226 |
&mixer1 { |
| 227 |
status = "okay"; |
| 228 |
}; |
| 229 |
|
| 230 |
&mmc0 { |
| 231 |
pinctrl-names = "default"; |
| 232 |
pinctrl-0 = <&mmc0_pins>; |
| 233 |
vmmc-supply = <®_dcdc1>; |
| 234 |
cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; |
| 235 |
disable-wp; |
| 236 |
bus-width = <4>; |
| 237 |
status = "okay"; |
| 238 |
}; |
| 239 |
|
| 240 |
&mmc1 { |
| 241 |
pinctrl-names = "default"; |
| 242 |
pinctrl-0 = <&mmc1_pins>; |
| 243 |
vmmc-supply = <®_dldo4>; |
| 244 |
vqmmc-supply = <®_eldo1>; |
| 245 |
mmc-pwrseq = <&wifi_pwrseq>; |
| 246 |
bus-width = <4>; |
| 247 |
non-removable; |
| 248 |
status = "okay"; |
| 249 |
|
| 250 |
rtl8723cs: wifi@1 { |
| 251 |
reg = <1>; |
| 252 |
}; |
| 253 |
}; |
| 254 |
|
| 255 |
&mmc2 { |
| 256 |
pinctrl-names = "default"; |
| 257 |
pinctrl-0 = <&mmc2_pins>; |
| 258 |
vmmc-supply = <®_dcdc1>; |
| 259 |
vqmmc-supply = <®_dcdc1>; |
| 260 |
bus-width = <8>; |
| 261 |
non-removable; |
| 262 |
cap-mmc-hw-reset; |
| 263 |
status = "okay"; |
| 264 |
}; |
| 265 |
|
| 266 |
&ohci0 { |
| 267 |
status = "okay"; |
| 268 |
}; |
| 269 |
|
| 270 |
&pwm { |
| 271 |
status = "okay"; |
| 272 |
}; |
| 273 |
|
| 274 |
&r_rsb { |
| 275 |
status = "okay"; |
| 276 |
|
| 277 |
axp803: pmic@3a3 { |
| 278 |
compatible = "x-powers,axp803"; |
| 279 |
reg = <0x3a3>; |
| 280 |
interrupt-parent = <&r_intc>; |
| 281 |
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; |
| 282 |
x-powers,drive-vbus-en; |
| 283 |
}; |
| 284 |
}; |
| 285 |
|
| 286 |
#include "axp803.dtsi" |
| 287 |
|
| 288 |
&ac_power_supply { |
| 289 |
status = "okay"; |
| 290 |
}; |
| 291 |
|
| 292 |
&battery_power_supply { |
| 293 |
status = "okay"; |
| 294 |
}; |
| 295 |
|
| 296 |
®_aldo1 { |
| 297 |
regulator-min-microvolt = <2800000>; |
| 298 |
regulator-max-microvolt = <2800000>; |
| 299 |
regulator-name = "dovdd-csi"; |
| 300 |
}; |
| 301 |
|
| 302 |
®_aldo2 { |
| 303 |
regulator-always-on; |
| 304 |
regulator-min-microvolt = <1800000>; |
| 305 |
regulator-max-microvolt = <3300000>; |
| 306 |
regulator-name = "vcc-pl"; |
| 307 |
}; |
| 308 |
|
| 309 |
®_aldo3 { |
| 310 |
regulator-always-on; |
| 311 |
regulator-min-microvolt = <2700000>; |
| 312 |
regulator-max-microvolt = <3300000>; |
| 313 |
regulator-name = "vcc-pll-avcc"; |
| 314 |
}; |
| 315 |
|
| 316 |
®_dc1sw { |
| 317 |
regulator-name = "vcc-lcd"; |
| 318 |
}; |
| 319 |
|
| 320 |
®_dcdc1 { |
| 321 |
regulator-always-on; |
| 322 |
regulator-min-microvolt = <3300000>; |
| 323 |
regulator-max-microvolt = <3300000>; |
| 324 |
regulator-name = "vcc-3v3"; |
| 325 |
}; |
| 326 |
|
| 327 |
®_dcdc2 { |
| 328 |
regulator-always-on; |
| 329 |
regulator-min-microvolt = <1000000>; |
| 330 |
regulator-max-microvolt = <1300000>; |
| 331 |
regulator-name = "vdd-cpux"; |
| 332 |
}; |
| 333 |
|
| 334 |
/* DCDC3 is polyphased with DCDC2 */ |
| 335 |
|
| 336 |
®_dcdc5 { |
| 337 |
regulator-always-on; |
| 338 |
regulator-min-microvolt = <1200000>; |
| 339 |
regulator-max-microvolt = <1200000>; |
| 340 |
regulator-name = "vcc-dram"; |
| 341 |
}; |
| 342 |
|
| 343 |
®_dcdc6 { |
| 344 |
regulator-always-on; |
| 345 |
regulator-min-microvolt = <1100000>; |
| 346 |
regulator-max-microvolt = <1100000>; |
| 347 |
regulator-name = "vdd-sys"; |
| 348 |
}; |
| 349 |
|
| 350 |
®_dldo1 { |
| 351 |
regulator-always-on; |
| 352 |
regulator-min-microvolt = <3300000>; |
| 353 |
regulator-max-microvolt = <3300000>; |
| 354 |
regulator-name = "vcc-hdmi-dsi-sensor"; |
| 355 |
}; |
| 356 |
|
| 357 |
®_dldo3 { |
| 358 |
regulator-min-microvolt = <2800000>; |
| 359 |
regulator-max-microvolt = <2800000>; |
| 360 |
regulator-name = "avdd-csi"; |
| 361 |
}; |
| 362 |
|
| 363 |
®_dldo4 { |
| 364 |
regulator-min-microvolt = <3300000>; |
| 365 |
regulator-max-microvolt = <3300000>; |
| 366 |
regulator-name = "vcc-wifi"; |
| 367 |
}; |
| 368 |
|
| 369 |
®_drivevbus { |
| 370 |
regulator-name = "usb0-vbus"; |
| 371 |
status = "okay"; |
| 372 |
}; |
| 373 |
|
| 374 |
®_eldo1 { |
| 375 |
regulator-always-on; |
| 376 |
regulator-min-microvolt = <1800000>; |
| 377 |
regulator-max-microvolt = <1800000>; |
| 378 |
regulator-name = "cpvdd"; |
| 379 |
}; |
| 380 |
|
| 381 |
®_eldo2 { |
| 382 |
regulator-min-microvolt = <1800000>; |
| 383 |
regulator-max-microvolt = <1800000>; |
| 384 |
regulator-name = "vcca-1v8"; |
| 385 |
}; |
| 386 |
|
| 387 |
®_eldo3 { |
| 388 |
regulator-min-microvolt = <1800000>; |
| 389 |
regulator-max-microvolt = <1800000>; |
| 390 |
regulator-name = "dvdd-1v8-csi"; |
| 391 |
}; |
| 392 |
|
| 393 |
®_fldo1 { |
| 394 |
regulator-min-microvolt = <1200000>; |
| 395 |
regulator-max-microvolt = <1200000>; |
| 396 |
regulator-name = "vcc-1v2-hsic"; |
| 397 |
}; |
| 398 |
|
| 399 |
®_fldo2 { |
| 400 |
regulator-always-on; |
| 401 |
regulator-min-microvolt = <1100000>; |
| 402 |
regulator-max-microvolt = <1100000>; |
| 403 |
regulator-name = "vdd-cpus"; |
| 404 |
}; |
| 405 |
|
| 406 |
®_ldo_io0 { |
| 407 |
regulator-min-microvolt = <3300000>; |
| 408 |
regulator-max-microvolt = <3300000>; |
| 409 |
regulator-name = "vcc-usb"; |
| 410 |
status = "okay"; |
| 411 |
}; |
| 412 |
|
| 413 |
®_ldo_io1 { |
| 414 |
regulator-min-microvolt = <3300000>; |
| 415 |
regulator-max-microvolt = <3300000>; |
| 416 |
regulator-enable-ramp-delay = <3500000>; |
| 417 |
regulator-name = "vcc-touchscreen"; |
| 418 |
status = "okay"; |
| 419 |
}; |
| 420 |
|
| 421 |
®_rtc_ldo { |
| 422 |
regulator-name = "vcc-rtc"; |
| 423 |
}; |
| 424 |
|
| 425 |
&simplefb_hdmi { |
| 426 |
vcc-hdmi-supply = <®_dldo1>; |
| 427 |
}; |
| 428 |
|
| 429 |
&hdmi { |
| 430 |
hvcc-supply = <®_dldo1>; |
| 431 |
status = "okay"; |
| 432 |
}; |
| 433 |
|
| 434 |
&hdmi_out { |
| 435 |
hdmi_out_con: endpoint { |
| 436 |
remote-endpoint = <&hdmi_con_in>; |
| 437 |
}; |
| 438 |
}; |
| 439 |
|
| 440 |
&sound { |
| 441 |
status = "okay"; |
| 442 |
simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>; |
| 443 |
simple-audio-card,widgets = "Microphone", "Internal Microphone Left", |
| 444 |
"Microphone", "Internal Microphone Right", |
| 445 |
"Headphone", "Headphone Jack", |
| 446 |
"Speaker", "Internal Speaker"; |
| 447 |
simple-audio-card,routing = |
| 448 |
"Left DAC", "DACL", |
| 449 |
"Right DAC", "DACR", |
| 450 |
"Speaker Amp INL", "LINEOUT", |
| 451 |
"Speaker Amp INR", "LINEOUT", |
| 452 |
"Internal Speaker", "Speaker Amp OUTL", |
| 453 |
"Internal Speaker", "Speaker Amp OUTR", |
| 454 |
"Headphone Jack", "HP", |
| 455 |
"ADCL", "Left ADC", |
| 456 |
"ADCR", "Right ADC", |
| 457 |
"Internal Microphone Left", "MBIAS", |
| 458 |
"MIC1", "Internal Microphone Left", |
| 459 |
"Internal Microphone Right", "HBIAS", |
| 460 |
"MIC2", "Internal Microphone Right"; |
| 461 |
}; |
| 462 |
|
| 463 |
&uart0 { |
| 464 |
pinctrl-names = "default"; |
| 465 |
pinctrl-0 = <&uart0_pb_pins>; |
| 466 |
status = "okay"; |
| 467 |
}; |
| 468 |
|
| 469 |
&usb_otg { |
| 470 |
dr_mode = "otg"; |
| 471 |
status = "okay"; |
| 472 |
}; |
| 473 |
|
| 474 |
&usb_power_supply { |
| 475 |
status = "okay"; |
| 476 |
}; |
| 477 |
|
| 478 |
&usbphy { |
| 479 |
usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */ |
| 480 |
usb0_vbus_power-supply = <&usb_power_supply>; |
| 481 |
usb0_vbus-supply = <®_drivevbus>; |
| 482 |
usb1_vbus-supply = <®_ldo_io0>; |
| 483 |
status = "okay"; |
| 484 |
}; |