Debian Codegraph @

scripts/dtc/include-prefixes/arm64/allwinner/sun50i-a64-pinephone.dtsi

raw
1 // SPDX-License-Identifier: (GPL-2.0+ OR MIT)
2 // Copyright (C) 2019 Icenowy Zheng <[email protected]>
3 // Copyright (C) 2020 Martijn Braam <[email protected]>
4 // Copyright (C) 2020 Ondrej Jirman <[email protected]>
5
6 #include "sun50i-a64.dtsi"
7 #include "sun50i-a64-cpu-opp.dtsi"
8
9 #include <dt-bindings/gpio/gpio.h>
10 #include <dt-bindings/input/input.h>
11 #include <dt-bindings/leds/common.h>
12 #include <dt-bindings/pwm/pwm.h>
13
14 / {
15 chassis-type = "handset";
16
17 aliases {
18 ethernet0 = &rtl8723cs;
19 serial0 = &uart0;
20 };
21
22 backlight: backlight {
23 compatible = "pwm-backlight";
24 pwms = <&r_pwm 0 50000 PWM_POLARITY_INVERTED>;
25 enable-gpios = <&pio 7 10 GPIO_ACTIVE_HIGH>; /* PH10 */
26 power-supply = <&reg_ps>;
27 /* Backlight configuration differs per PinePhone revision. */
28 };
29
30 bt_sco_codec: bt-sco-codec {
31 #sound-dai-cells = <1>;
32 compatible = "linux,bt-sco";
33 };
34
35 chosen {
36 stdout-path = "serial0:115200n8";
37 };
38
39 leds {
40 compatible = "gpio-leds";
41
42 led0: led-0 {
43 function = LED_FUNCTION_INDICATOR;
44 color = <LED_COLOR_ID_BLUE>;
45 gpios = <&pio 3 20 GPIO_ACTIVE_HIGH>; /* PD20 */
46 retain-state-suspended;
47 };
48
49 led1: led-1 {
50 function = LED_FUNCTION_INDICATOR;
51 color = <LED_COLOR_ID_GREEN>;
52 gpios = <&pio 3 18 GPIO_ACTIVE_HIGH>; /* PD18 */
53 retain-state-suspended;
54 };
55
56 led2: led-2 {
57 function = LED_FUNCTION_INDICATOR;
58 color = <LED_COLOR_ID_RED>;
59 gpios = <&pio 3 19 GPIO_ACTIVE_HIGH>; /* PD19 */
60 retain-state-suspended;
61 };
62 };
63
64 multi-led {
65 compatible = "leds-group-multicolor";
66 color = <LED_COLOR_ID_RGB>;
67 function = LED_FUNCTION_INDICATOR;
68 leds = <&led0>, <&led1>, <&led2>;
69 };
70
71 reg_ps: ps-regulator {
72 compatible = "regulator-fixed";
73 regulator-name = "ps";
74 regulator-min-microvolt = <5000000>;
75 regulator-max-microvolt = <5000000>;
76 regulator-boot-on;
77 };
78
79 reg_vbat_wifi: vbat-wifi {
80 compatible = "regulator-fixed";
81 regulator-min-microvolt = <3300000>;
82 regulator-max-microvolt = <3300000>;
83 regulator-name = "vbat-wifi";
84 };
85
86 sgm3140: led-controller {
87 compatible = "sgmicro,sgm3140";
88 vin-supply = <&reg_dcdc1>;
89
90 sgm3140_flash: led {
91 function = LED_FUNCTION_FLASH;
92 color = <LED_COLOR_ID_WHITE>;
93 flash-max-timeout-us = <250000>;
94 };
95 };
96
97 speaker_amp: audio-amplifier {
98 compatible = "simple-audio-amplifier";
99 enable-gpios = <&pio 2 7 GPIO_ACTIVE_HIGH>; /* PC7 */
100 sound-name-prefix = "Speaker Amp";
101 };
102
103 vibrator {
104 compatible = "gpio-vibrator";
105 enable-gpios = <&pio 3 2 GPIO_ACTIVE_HIGH>; /* PD2 */
106 vcc-supply = <&reg_dcdc1>;
107 };
108 };
109
110 &codec {
111 pinctrl-names = "default";
112 pinctrl-0 = <&aif3_pins>;
113 status = "okay";
114 };
115
116 &codec_analog {
117 cpvdd-supply = <&reg_eldo1>;
118 status = "okay";
119 };
120
121 &cpu0 {
122 cpu-supply = <&reg_dcdc2>;
123 };
124
125 &cpu1 {
126 cpu-supply = <&reg_dcdc2>;
127 };
128
129 &cpu2 {
130 cpu-supply = <&reg_dcdc2>;
131 };
132
133 &cpu3 {
134 cpu-supply = <&reg_dcdc2>;
135 };
136
137 &dai {
138 status = "okay";
139 };
140
141 &de {
142 status = "okay";
143 };
144
145 &dphy {
146 status = "okay";
147 };
148
149 &dsi {
150 vcc-dsi-supply = <&reg_dldo1>;
151 status = "okay";
152
153 panel@0 {
154 compatible = "xingbangda,xbd599";
155 reg = <0>;
156 reset-gpios = <&pio 3 23 GPIO_ACTIVE_LOW>; /* PD23 */
157 iovcc-supply = <&reg_dldo2>;
158 vcc-supply = <&reg_ldo_io0>;
159 backlight = <&backlight>;
160 };
161 };
162
163 &ehci0 {
164 status = "okay";
165 };
166
167 &ehci1 {
168 status = "okay";
169 };
170
171 &i2c0 {
172 status = "okay";
173
174 touchscreen@5d {
175 compatible = "goodix,gt917s";
176 reg = <0x5d>;
177 interrupt-parent = <&pio>;
178 interrupts = <7 4 IRQ_TYPE_LEVEL_HIGH>; /* PH4 */
179 irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */
180 reset-gpios = <&pio 7 11 GPIO_ACTIVE_HIGH>; /* PH11 */
181 AVDD28-supply = <&reg_ldo_io0>;
182 VDDIO-supply = <&reg_ldo_io0>;
183 touchscreen-size-x = <720>;
184 touchscreen-size-y = <1440>;
185 };
186 };
187
188 &i2c1 {
189 status = "okay";
190
191 /* Alternative magnetometer */
192 af8133j: magnetometer@1c {
193 compatible = "voltafield,af8133j";
194 reg = <0x1c>;
195 reset-gpios = <&pio 1 1 GPIO_ACTIVE_LOW>;
196 avdd-supply = <&reg_dldo1>;
197 dvdd-supply = <&reg_dldo1>;
198 mount-matrix = "0", "-1", "0",
199 "-1", "0", "0",
200 "0", "0", "-1";
201
202 /* status will be fixed up in firmware */
203 status = "disabled";
204 };
205
206 /* Magnetometer */
207 lis3mdl: magnetometer@1e {
208 compatible = "st,lis3mdl-magn";
209 reg = <0x1e>;
210 vdd-supply = <&reg_dldo1>;
211 vddio-supply = <&reg_dldo1>;
212 mount-matrix = "0", "1", "0",
213 "-1", "0", "0",
214 "0", "0", "1";
215 };
216
217 /* Light/proximity sensor */
218 light-sensor@48 {
219 compatible = "sensortek,stk3311";
220 reg = <0x48>;
221 interrupt-parent = <&pio>;
222 interrupts = <1 0 IRQ_TYPE_EDGE_FALLING>; /* PB0 */
223 };
224
225 /* Accelerometer/gyroscope */
226 accelerometer@68 {
227 compatible = "invensense,mpu6050";
228 reg = <0x68>;
229 interrupt-parent = <&pio>;
230 interrupts = <7 5 IRQ_TYPE_EDGE_RISING>; /* PH5 */
231 vdd-supply = <&reg_dldo1>;
232 vddio-supply = <&reg_dldo1>;
233 mount-matrix = "0", "1", "0",
234 "-1", "0", "0",
235 "0", "0", "1";
236 };
237 };
238
239 /* Connected to pogo pins (external spring based pinheader for user addons) */
240 &i2c2 {
241 status = "okay";
242 };
243
244 &lradc {
245 vref-supply = <&reg_aldo3>;
246 wakeup-source;
247 status = "okay";
248
249 button-200 {
250 label = "Volume Up";
251 linux,code = <KEY_VOLUMEUP>;
252 channel = <0>;
253 voltage = <200000>;
254 };
255
256 button-400 {
257 label = "Volume Down";
258 linux,code = <KEY_VOLUMEDOWN>;
259 channel = <0>;
260 voltage = <400000>;
261 };
262 };
263
264 &mmc0 {
265 pinctrl-names = "default";
266 pinctrl-0 = <&mmc0_pins>;
267 vmmc-supply = <&reg_dcdc1>;
268 vqmmc-supply = <&reg_dcdc1>;
269 cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>; /* PF6 */
270 disable-wp;
271 bus-width = <4>;
272 status = "okay";
273 };
274
275 &mmc1 {
276 pinctrl-names = "default";
277 pinctrl-0 = <&mmc1_pins>;
278 vmmc-supply = <&reg_vbat_wifi>;
279 vqmmc-supply = <&reg_dldo4>;
280 bus-width = <4>;
281 non-removable;
282 status = "okay";
283
284 rtl8723cs: wifi@1 {
285 reg = <1>;
286 };
287 };
288
289 &mmc2 {
290 pinctrl-names = "default";
291 pinctrl-0 = <&mmc2_pins>;
292 vmmc-supply = <&reg_dcdc1>;
293 vqmmc-supply = <&reg_dcdc1>;
294 bus-width = <8>;
295 non-removable;
296 cap-mmc-hw-reset;
297 status = "okay";
298 };
299
300 &ohci0 {
301 status = "okay";
302 };
303
304 &ohci1 {
305 status = "okay";
306 };
307
308 &pio {
309 vcc-pb-supply = <&reg_dcdc1>;
310 vcc-pc-supply = <&reg_dcdc1>;
311 vcc-pd-supply = <&reg_dcdc1>;
312 vcc-pe-supply = <&reg_aldo1>;
313 vcc-pf-supply = <&reg_dcdc1>;
314 vcc-pg-supply = <&reg_dldo4>;
315 vcc-ph-supply = <&reg_dcdc1>;
316 };
317
318 &r_pio {
319 /*
320 * FIXME: We can't add that supply for now since it would
321 * create a circular dependency between pinctrl, the regulator
322 * and the RSB Bus.
323 *
324 * vcc-pl-supply = <&reg_aldo2>;
325 */
326 };
327
328 &r_pwm {
329 status = "okay";
330 };
331
332 &r_rsb {
333 status = "okay";
334
335 axp803: pmic@3a3 {
336 compatible = "x-powers,axp803";
337 reg = <0x3a3>;
338 interrupt-parent = <&r_intc>;
339 interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
340 };
341 };
342
343 #include "axp803.dtsi"
344
345 &battery_power_supply {
346 status = "okay";
347 };
348
349 &reg_aldo1 {
350 regulator-min-microvolt = <1800000>;
351 regulator-max-microvolt = <1800000>;
352 regulator-name = "dovdd-csi";
353 };
354
355 &reg_aldo2 {
356 regulator-always-on;
357 regulator-min-microvolt = <1800000>;
358 regulator-max-microvolt = <1800000>;
359 regulator-name = "vcc-pl";
360 };
361
362 &reg_aldo3 {
363 regulator-always-on;
364 regulator-min-microvolt = <3000000>;
365 regulator-max-microvolt = <3000000>;
366 regulator-name = "vcc-pll-avcc";
367 };
368
369 &reg_dcdc1 {
370 regulator-always-on;
371 regulator-min-microvolt = <3300000>;
372 regulator-max-microvolt = <3300000>;
373 regulator-name = "vcc-3v3";
374 };
375
376 &reg_dcdc2 {
377 regulator-always-on;
378 regulator-min-microvolt = <1000000>;
379 regulator-max-microvolt = <1300000>;
380 regulator-name = "vdd-cpux";
381 };
382
383 /* DCDC3 is polyphased with DCDC2 */
384
385 &reg_dcdc5 {
386 regulator-always-on;
387 regulator-min-microvolt = <1200000>;
388 regulator-max-microvolt = <1200000>;
389 regulator-name = "vcc-dram";
390 };
391
392 &reg_dcdc6 {
393 regulator-always-on;
394 regulator-min-microvolt = <1100000>;
395 regulator-max-microvolt = <1100000>;
396 regulator-name = "vdd-sys";
397 };
398
399 &reg_dldo1 {
400 regulator-min-microvolt = <3300000>;
401 regulator-max-microvolt = <3300000>;
402 regulator-name = "vcc-dsi-sensor";
403 };
404
405 &reg_dldo2 {
406 regulator-min-microvolt = <1800000>;
407 regulator-max-microvolt = <1800000>;
408 regulator-name = "vcc-mipi-io";
409 };
410
411 &reg_dldo3 {
412 regulator-min-microvolt = <2800000>;
413 regulator-max-microvolt = <2800000>;
414 regulator-name = "avdd-csi";
415 };
416
417 &reg_dldo4 {
418 regulator-min-microvolt = <1800000>;
419 regulator-max-microvolt = <1800000>;
420 regulator-name = "vcc-wifi-io";
421 };
422
423 &reg_eldo1 {
424 regulator-always-on;
425 regulator-min-microvolt = <1800000>;
426 regulator-max-microvolt = <1800000>;
427 regulator-name = "vcc-lpddr";
428 };
429
430 &reg_eldo3 {
431 regulator-min-microvolt = <1800000>;
432 regulator-max-microvolt = <1800000>;
433 regulator-name = "dvdd-1v8-csi";
434 };
435
436 &reg_fldo1 {
437 regulator-min-microvolt = <1200000>;
438 regulator-max-microvolt = <1200000>;
439 regulator-name = "vcc-1v2-hsic";
440 };
441
442 &reg_fldo2 {
443 regulator-always-on;
444 regulator-min-microvolt = <1100000>;
445 regulator-max-microvolt = <1100000>;
446 regulator-name = "vdd-cpus";
447 };
448
449 &reg_ldo_io0 {
450 regulator-min-microvolt = <3300000>;
451 regulator-max-microvolt = <3300000>;
452 regulator-name = "vcc-lcd-ctp-stk";
453 status = "okay";
454 };
455
456 &reg_ldo_io1 {
457 regulator-min-microvolt = <1800000>;
458 regulator-max-microvolt = <1800000>;
459 regulator-name = "vcc-1v8-typec";
460 status = "okay";
461 };
462
463 &reg_rtc_ldo {
464 regulator-name = "vcc-rtc";
465 };
466
467 &sound {
468 status = "okay";
469 simple-audio-card,name = "PinePhone";
470 simple-audio-card,aux-devs = <&codec_analog>, <&speaker_amp>;
471 simple-audio-card,widgets = "Microphone", "Headset Microphone",
472 "Microphone", "Internal Microphone",
473 "Headphone", "Headphone Jack",
474 "Speaker", "Internal Earpiece",
475 "Speaker", "Internal Speaker";
476 simple-audio-card,routing =
477 "Headphone Jack", "HP",
478 "Internal Earpiece", "EARPIECE",
479 "Internal Speaker", "Speaker Amp OUTL",
480 "Internal Speaker", "Speaker Amp OUTR",
481 "Speaker Amp INL", "LINEOUT",
482 "Speaker Amp INR", "LINEOUT",
483 "Left DAC", "DACL",
484 "Right DAC", "DACR",
485 "ADCL", "Left ADC",
486 "ADCR", "Right ADC",
487 "Internal Microphone", "MBIAS",
488 "MIC1", "Internal Microphone",
489 "Headset Microphone", "HBIAS",
490 "MIC2", "Headset Microphone";
491
492 simple-audio-card,dai-link@2 {
493 format = "dsp_a";
494 frame-master = <&link2_codec>;
495 bitclock-master = <&link2_codec>;
496 bitclock-inversion;
497
498 link2_cpu: cpu {
499 sound-dai = <&bt_sco_codec 0>;
500 };
501
502 link2_codec: codec {
503 sound-dai = <&codec 2>;
504 dai-tdm-slot-num = <1>;
505 dai-tdm-slot-width = <32>;
506 };
507 };
508 };
509
510 &uart0 {
511 pinctrl-names = "default";
512 pinctrl-0 = <&uart0_pb_pins>;
513 status = "okay";
514 };
515
516 &uart1 {
517 pinctrl-names = "default";
518 pinctrl-0 = <&uart1_pins>, <&uart1_rts_cts_pins>;
519 status = "okay";
520
521 bluetooth {
522 compatible = "realtek,rtl8723cs-bt";
523 device-wake-gpios = <&pio 7 6 GPIO_ACTIVE_LOW>; /* PH6 */
524 enable-gpios = <&r_pio 0 4 GPIO_ACTIVE_HIGH>; /* PL4 */
525 host-wake-gpios = <&r_pio 0 5 GPIO_ACTIVE_HIGH>; /* PL5 */
526 };
527 };
528
529 /* Connected to the modem (hardware flow control can't be used) */
530 &uart3 {
531 pinctrl-names = "default";
532 pinctrl-0 = <&uart3_pins>;
533 status = "okay";
534 };
535
536 &usb_otg {
537 dr_mode = "peripheral";
538 status = "okay";
539 };
540
541 &usb_power_supply {
542 status = "okay";
543 };
544
545 &usbphy {
546 status = "okay";
547 };