| 1 |
// SPDX-License-Identifier: (GPL-2.0+ OR MIT) |
| 2 |
// Copyright (C) 2018 Amarula Solutions B.V. |
| 3 |
// Author: Jagan Teki <[email protected]> |
| 4 |
|
| 5 |
/dts-v1/; |
| 6 |
|
| 7 |
#include "sun50i-a64.dtsi" |
| 8 |
#include "sun50i-a64-cpu-opp.dtsi" |
| 9 |
|
| 10 |
#include <dt-bindings/gpio/gpio.h> |
| 11 |
|
| 12 |
/ { |
| 13 |
model = "Amarula A64-Relic"; |
| 14 |
compatible = "amarula,a64-relic", "allwinner,sun50i-a64"; |
| 15 |
|
| 16 |
aliases { |
| 17 |
serial0 = &uart0; |
| 18 |
}; |
| 19 |
|
| 20 |
chosen { |
| 21 |
stdout-path = "serial0:115200n8"; |
| 22 |
}; |
| 23 |
|
| 24 |
i2c { |
| 25 |
compatible = "i2c-gpio"; |
| 26 |
sda-gpios = <&pio 4 13 GPIO_ACTIVE_HIGH>; |
| 27 |
scl-gpios = <&pio 4 12 GPIO_ACTIVE_HIGH>; |
| 28 |
i2c-gpio,delay-us = <5>; |
| 29 |
#address-cells = <1>; |
| 30 |
#size-cells = <0>; |
| 31 |
|
| 32 |
ov5640: camera@3c { |
| 33 |
compatible = "ovti,ov5640"; |
| 34 |
reg = <0x3c>; |
| 35 |
pinctrl-names = "default"; |
| 36 |
pinctrl-0 = <&csi_mclk_pin>; |
| 37 |
clocks = <&ccu CLK_CSI_MCLK>; |
| 38 |
clock-names = "xclk"; |
| 39 |
|
| 40 |
AVDD-supply = <®_aldo1>; |
| 41 |
DOVDD-supply = <®_dldo3>; |
| 42 |
DVDD-supply = <®_eldo3>; |
| 43 |
reset-gpios = <&pio 4 14 GPIO_ACTIVE_LOW>; /* CSI-RST-R: PE14 */ |
| 44 |
powerdown-gpios = <&pio 4 15 GPIO_ACTIVE_HIGH>; /* CSI-STBY-R: PE15 */ |
| 45 |
|
| 46 |
port { |
| 47 |
ov5640_ep: endpoint { |
| 48 |
remote-endpoint = <&csi_ep>; |
| 49 |
bus-width = <8>; |
| 50 |
hsync-active = <1>; /* Active high */ |
| 51 |
vsync-active = <0>; /* Active low */ |
| 52 |
data-active = <1>; /* Active high */ |
| 53 |
pclk-sample = <1>; /* Rising */ |
| 54 |
}; |
| 55 |
}; |
| 56 |
}; |
| 57 |
}; |
| 58 |
|
| 59 |
wifi_pwrseq: wifi-pwrseq { |
| 60 |
compatible = "mmc-pwrseq-simple"; |
| 61 |
clocks = <&rtc CLK_OSC32K_FANOUT>; |
| 62 |
clock-names = "ext_clock"; |
| 63 |
reset-gpios = <&r_pio 0 2 GPIO_ACTIVE_LOW>; /* WL-PMU-EN: PL2 */ |
| 64 |
}; |
| 65 |
}; |
| 66 |
|
| 67 |
&cpu0 { |
| 68 |
cpu-supply = <®_dcdc2>; |
| 69 |
}; |
| 70 |
|
| 71 |
&cpu1 { |
| 72 |
cpu-supply = <®_dcdc2>; |
| 73 |
}; |
| 74 |
|
| 75 |
&cpu2 { |
| 76 |
cpu-supply = <®_dcdc2>; |
| 77 |
}; |
| 78 |
|
| 79 |
&cpu3 { |
| 80 |
cpu-supply = <®_dcdc2>; |
| 81 |
}; |
| 82 |
|
| 83 |
&csi { |
| 84 |
status = "okay"; |
| 85 |
|
| 86 |
port { |
| 87 |
csi_ep: endpoint { |
| 88 |
remote-endpoint = <&ov5640_ep>; |
| 89 |
bus-width = <8>; |
| 90 |
hsync-active = <1>; /* Active high */ |
| 91 |
vsync-active = <0>; /* Active low */ |
| 92 |
data-active = <1>; /* Active high */ |
| 93 |
pclk-sample = <1>; /* Rising */ |
| 94 |
}; |
| 95 |
}; |
| 96 |
}; |
| 97 |
|
| 98 |
&ehci0 { |
| 99 |
status = "okay"; |
| 100 |
}; |
| 101 |
|
| 102 |
&i2c0 { |
| 103 |
status = "okay"; |
| 104 |
|
| 105 |
sensor@48 { |
| 106 |
compatible = "st,stlm75"; |
| 107 |
reg = <0x48>; |
| 108 |
}; |
| 109 |
}; |
| 110 |
|
| 111 |
&i2c0_pins { |
| 112 |
bias-pull-up; |
| 113 |
}; |
| 114 |
|
| 115 |
&i2c1 { |
| 116 |
status = "okay"; |
| 117 |
|
| 118 |
touchscreen@5d { |
| 119 |
compatible = "goodix,gt5663"; |
| 120 |
reg = <0x5d>; |
| 121 |
AVDD28-supply = <®_ldo_io0>; /* VCC-CTP: GPIO0-LDO */ |
| 122 |
interrupt-parent = <&pio>; |
| 123 |
interrupts = <7 4 IRQ_TYPE_EDGE_FALLING>; |
| 124 |
irq-gpios = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* CTP-INT: PH4 */ |
| 125 |
reset-gpios = <&pio 7 8 GPIO_ACTIVE_HIGH>; /* CTP-RST: PH8 */ |
| 126 |
touchscreen-inverted-x; |
| 127 |
touchscreen-inverted-y; |
| 128 |
}; |
| 129 |
}; |
| 130 |
|
| 131 |
&mmc1 { |
| 132 |
pinctrl-names = "default"; |
| 133 |
pinctrl-0 = <&mmc1_pins>; |
| 134 |
vmmc-supply = <®_dcdc1>; |
| 135 |
/* |
| 136 |
* Schematic shows both dldo4 and eldo1 connected for vcc-io-wifi, but |
| 137 |
* dldo4 connection shows DNP(Do Not Populate) and eldo1 connected with |
| 138 |
* 0Ohm register to vcc-io-wifi so eldo1 is used. |
| 139 |
*/ |
| 140 |
vqmmc-supply = <®_eldo1>; |
| 141 |
mmc-pwrseq = <&wifi_pwrseq>; |
| 142 |
bus-width = <4>; |
| 143 |
non-removable; |
| 144 |
status = "okay"; |
| 145 |
|
| 146 |
brcmf: wifi@1 { |
| 147 |
reg = <1>; |
| 148 |
compatible = "brcm,bcm4329-fmac"; |
| 149 |
interrupt-parent = <&r_pio>; |
| 150 |
interrupts = <0 3 IRQ_TYPE_LEVEL_LOW>; /* WL-WAKE-AP: PL3 */ |
| 151 |
interrupt-names = "host-wake"; |
| 152 |
}; |
| 153 |
}; |
| 154 |
|
| 155 |
&mmc2 { |
| 156 |
pinctrl-names = "default"; |
| 157 |
pinctrl-0 = <&mmc2_pins>; |
| 158 |
vmmc-supply = <®_dcdc1>; |
| 159 |
bus-width = <8>; |
| 160 |
non-removable; |
| 161 |
cap-mmc-hw-reset; |
| 162 |
status = "okay"; |
| 163 |
}; |
| 164 |
|
| 165 |
&ohci0 { |
| 166 |
status = "okay"; |
| 167 |
}; |
| 168 |
|
| 169 |
&r_rsb { |
| 170 |
status = "okay"; |
| 171 |
|
| 172 |
axp803: pmic@3a3 { |
| 173 |
compatible = "x-powers,axp803"; |
| 174 |
reg = <0x3a3>; |
| 175 |
interrupt-parent = <&r_intc>; |
| 176 |
interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>; |
| 177 |
x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */ |
| 178 |
}; |
| 179 |
}; |
| 180 |
|
| 181 |
#include "axp803.dtsi" |
| 182 |
|
| 183 |
®_aldo1 { |
| 184 |
regulator-always-on; |
| 185 |
regulator-min-microvolt = <2800000>; |
| 186 |
regulator-max-microvolt = <2800000>; |
| 187 |
regulator-name = "avdd-csi"; |
| 188 |
}; |
| 189 |
|
| 190 |
®_aldo2 { |
| 191 |
regulator-always-on; |
| 192 |
regulator-min-microvolt = <1800000>; |
| 193 |
regulator-max-microvolt = <3300000>; |
| 194 |
regulator-name = "vcc-pl"; |
| 195 |
}; |
| 196 |
|
| 197 |
®_aldo3 { |
| 198 |
regulator-always-on; |
| 199 |
regulator-min-microvolt = <3000000>; |
| 200 |
regulator-max-microvolt = <3000000>; |
| 201 |
regulator-name = "vcc-pll-avcc"; |
| 202 |
}; |
| 203 |
|
| 204 |
®_dcdc1 { |
| 205 |
regulator-always-on; |
| 206 |
regulator-min-microvolt = <3300000>; |
| 207 |
regulator-max-microvolt = <3300000>; |
| 208 |
regulator-name = "vcc-3v3"; |
| 209 |
}; |
| 210 |
|
| 211 |
®_dcdc2 { |
| 212 |
regulator-always-on; |
| 213 |
regulator-min-microvolt = <1040000>; |
| 214 |
regulator-max-microvolt = <1300000>; |
| 215 |
regulator-name = "vdd-cpux"; |
| 216 |
}; |
| 217 |
|
| 218 |
/* DCDC3 is polyphased with DCDC2 */ |
| 219 |
|
| 220 |
®_dcdc5 { |
| 221 |
regulator-always-on; |
| 222 |
regulator-min-microvolt = <1500000>; |
| 223 |
regulator-max-microvolt = <1500000>; |
| 224 |
regulator-name = "vcc-dram"; |
| 225 |
}; |
| 226 |
|
| 227 |
®_dcdc6 { |
| 228 |
regulator-always-on; |
| 229 |
regulator-min-microvolt = <1100000>; |
| 230 |
regulator-max-microvolt = <1100000>; |
| 231 |
regulator-name = "vdd-sys"; |
| 232 |
}; |
| 233 |
|
| 234 |
®_dldo1 { |
| 235 |
regulator-min-microvolt = <3300000>; |
| 236 |
regulator-max-microvolt = <3300000>; |
| 237 |
regulator-name = "vcc-hdmi-dsi-sensor"; |
| 238 |
}; |
| 239 |
|
| 240 |
®_dldo2 { |
| 241 |
regulator-min-microvolt = <3300000>; |
| 242 |
regulator-max-microvolt = <3300000>; |
| 243 |
regulator-name = "vcc-mipi"; |
| 244 |
}; |
| 245 |
|
| 246 |
®_dldo3 { |
| 247 |
regulator-min-microvolt = <2800000>; |
| 248 |
regulator-max-microvolt = <2800000>; |
| 249 |
regulator-name = "dovdd-csi"; |
| 250 |
}; |
| 251 |
|
| 252 |
®_dldo4 { |
| 253 |
regulator-min-microvolt = <3300000>; |
| 254 |
regulator-max-microvolt = <3300000>; |
| 255 |
regulator-name = "vcc-wifi-io"; |
| 256 |
}; |
| 257 |
|
| 258 |
®_drivevbus { |
| 259 |
regulator-name = "usb0-vbus"; |
| 260 |
status = "okay"; |
| 261 |
}; |
| 262 |
|
| 263 |
®_eldo1 { |
| 264 |
regulator-always-on; |
| 265 |
regulator-min-microvolt = <1800000>; |
| 266 |
regulator-max-microvolt = <1800000>; |
| 267 |
regulator-name = "cpvdd"; |
| 268 |
}; |
| 269 |
|
| 270 |
®_eldo3 { |
| 271 |
regulator-min-microvolt = <1800000>; |
| 272 |
regulator-max-microvolt = <1800000>; |
| 273 |
regulator-name = "dvdd-csi"; |
| 274 |
}; |
| 275 |
|
| 276 |
®_fldo1 { |
| 277 |
regulator-min-microvolt = <1200000>; |
| 278 |
regulator-max-microvolt = <1200000>; |
| 279 |
regulator-name = "vcc-1v2-hsic"; |
| 280 |
}; |
| 281 |
|
| 282 |
/* |
| 283 |
* The A64 chip cannot work without this regulator off, although |
| 284 |
* it seems to be only driving the AR100 core. |
| 285 |
* Maybe we don't still know well about CPUs domain. |
| 286 |
*/ |
| 287 |
®_fldo2 { |
| 288 |
regulator-always-on; |
| 289 |
regulator-min-microvolt = <1100000>; |
| 290 |
regulator-max-microvolt = <1100000>; |
| 291 |
regulator-name = "vdd-cpus"; |
| 292 |
}; |
| 293 |
|
| 294 |
®_ldo_io0 { |
| 295 |
regulator-min-microvolt = <2800000>; |
| 296 |
regulator-max-microvolt = <2800000>; |
| 297 |
regulator-name = "vcc-ctp"; |
| 298 |
status = "okay"; |
| 299 |
}; |
| 300 |
|
| 301 |
®_rtc_ldo { |
| 302 |
regulator-name = "vcc-rtc"; |
| 303 |
}; |
| 304 |
|
| 305 |
&uart0 { |
| 306 |
pinctrl-names = "default"; |
| 307 |
pinctrl-0 = <&uart0_pb_pins>; |
| 308 |
status = "okay"; |
| 309 |
}; |
| 310 |
|
| 311 |
&usb_otg { |
| 312 |
dr_mode = "otg"; |
| 313 |
status = "okay"; |
| 314 |
}; |
| 315 |
|
| 316 |
&usbphy { |
| 317 |
usb0_id_det-gpios = <&pio 7 9 GPIO_ACTIVE_HIGH>; /* PH9 */ |
| 318 |
usb0_vbus-supply = <®_drivevbus>; |
| 319 |
status = "okay"; |
| 320 |
}; |