| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* |
| 3 |
* RapidIO mport driver for Tsi721 PCIExpress-to-SRIO bridge |
| 4 |
* |
| 5 |
* Copyright 2011 Integrated Device Technology, Inc. |
| 6 |
* Alexandre Bounine <[email protected]> |
| 7 |
* Chul Kim <[email protected]> |
| 8 |
*/ |
| 9 |
|
| 10 |
#include <linux/io.h> |
| 11 |
#include <linux/errno.h> |
| 12 |
#include <linux/init.h> |
| 13 |
#include <linux/ioport.h> |
| 14 |
#include <linux/kernel.h> |
| 15 |
#include <linux/module.h> |
| 16 |
#include <linux/pci.h> |
| 17 |
#include <linux/rio.h> |
| 18 |
#include <linux/rio_drv.h> |
| 19 |
#include <linux/dma-mapping.h> |
| 20 |
#include <linux/interrupt.h> |
| 21 |
#include <linux/kfifo.h> |
| 22 |
#include <linux/delay.h> |
| 23 |
|
| 24 |
#include "tsi721.h" |
| 25 |
|
| 26 |
#ifdef DEBUG |
| 27 |
u32 tsi_dbg_level; |
| 28 |
module_param_named(dbg_level, tsi_dbg_level, uint, S_IWUSR | S_IRUGO); |
| 29 |
MODULE_PARM_DESC(dbg_level, "Debugging output level (default 0 = none)"); |
| 30 |
#endif |
| 31 |
|
| 32 |
static int pcie_mrrs = -1; |
| 33 |
module_param(pcie_mrrs, int, S_IRUGO); |
| 34 |
MODULE_PARM_DESC(pcie_mrrs, "PCIe MRRS override value (0...5)"); |
| 35 |
|
| 36 |
static u8 mbox_sel = 0x0f; |
| 37 |
module_param(mbox_sel, byte, S_IRUGO); |
| 38 |
MODULE_PARM_DESC(mbox_sel, |
| 39 |
"RIO Messaging MBOX Selection Mask (default: 0x0f = all)"); |
| 40 |
|
| 41 |
static DEFINE_SPINLOCK(tsi721_maint_lock); |
| 42 |
|
| 43 |
static void tsi721_omsg_handler(struct tsi721_device *priv, int ch); |
| 44 |
static void tsi721_imsg_handler(struct tsi721_device *priv, int ch); |
| 45 |
|
| 46 |
/** |
| 47 |
* tsi721_lcread - read from local SREP config space |
| 48 |
* @mport: RapidIO master port info |
| 49 |
* @index: ID of RapdiIO interface |
| 50 |
* @offset: Offset into configuration space |
| 51 |
* @len: Length (in bytes) of the maintenance transaction |
| 52 |
* @data: Value to be read into |
| 53 |
* |
| 54 |
* Generates a local SREP space read. |
| 55 |
* |
| 56 |
* Returns: %0 on success or %-EINVAL on failure. |
| 57 |
*/ |
| 58 |
static int tsi721_lcread(struct rio_mport *mport, int index, u32 offset, |
| 59 |
int len, u32 *data) |
| 60 |
{ |
| 61 |
struct tsi721_device *priv = mport->priv; |
| 62 |
|
| 63 |
if (len != sizeof(u32)) |
| 64 |
return -EINVAL; /* only 32-bit access is supported */ |
| 65 |
|
| 66 |
*data = ioread32(priv->regs + offset); |
| 67 |
|
| 68 |
return 0; |
| 69 |
} |
| 70 |
|
| 71 |
/** |
| 72 |
* tsi721_lcwrite - write into local SREP config space |
| 73 |
* @mport: RapidIO master port info |
| 74 |
* @index: ID of RapdiIO interface |
| 75 |
* @offset: Offset into configuration space |
| 76 |
* @len: Length (in bytes) of the maintenance transaction |
| 77 |
* @data: Value to be written |
| 78 |
* |
| 79 |
* Generates a local write into SREP configuration space. |
| 80 |
* |
| 81 |
* Returns: %0 on success or %-EINVAL on failure. |
| 82 |
*/ |
| 83 |
static int tsi721_lcwrite(struct rio_mport *mport, int index, u32 offset, |
| 84 |
int len, u32 data) |
| 85 |
{ |
| 86 |
struct tsi721_device *priv = mport->priv; |
| 87 |
|
| 88 |
if (len != sizeof(u32)) |
| 89 |
return -EINVAL; /* only 32-bit access is supported */ |
| 90 |
|
| 91 |
iowrite32(data, priv->regs + offset); |
| 92 |
|
| 93 |
return 0; |
| 94 |
} |
| 95 |
|
| 96 |
/** |
| 97 |
* tsi721_maint_dma - Helper function to generate RapidIO maintenance |
| 98 |
* transactions using designated Tsi721 DMA channel. |
| 99 |
* @priv: pointer to tsi721 private data |
| 100 |
* @sys_size: RapdiIO transport system size |
| 101 |
* @destid: Destination ID of transaction |
| 102 |
* @hopcount: Number of hops to target device |
| 103 |
* @offset: Offset into configuration space |
| 104 |
* @len: Length (in bytes) of the maintenance transaction |
| 105 |
* @data: Location to be read from or write into |
| 106 |
* @do_wr: Operation flag (1 == MAINT_WR) |
| 107 |
* |
| 108 |
* Generates a RapidIO maintenance transaction (Read or Write). |
| 109 |
* Returns: %0 on success and %-EINVAL or %-EFAULT on failure. |
| 110 |
*/ |
| 111 |
static int tsi721_maint_dma(struct tsi721_device *priv, u32 sys_size, |
| 112 |
u16 destid, u8 hopcount, u32 offset, int len, |
| 113 |
u32 *data, int do_wr) |
| 114 |
{ |
| 115 |
void __iomem *regs = priv->regs + TSI721_DMAC_BASE(priv->mdma.ch_id); |
| 116 |
struct tsi721_dma_desc *bd_ptr; |
| 117 |
u32 rd_count, swr_ptr, ch_stat; |
| 118 |
unsigned long flags; |
| 119 |
int i, err = 0; |
| 120 |
u32 op = do_wr ? MAINT_WR : MAINT_RD; |
| 121 |
|
| 122 |
if (offset > (RIO_MAINT_SPACE_SZ - len) || (len != sizeof(u32))) |
| 123 |
return -EINVAL; |
| 124 |
|
| 125 |
spin_lock_irqsave(&tsi721_maint_lock, flags); |
| 126 |
|
| 127 |
bd_ptr = priv->mdma.bd_base; |
| 128 |
|
| 129 |
rd_count = ioread32(regs + TSI721_DMAC_DRDCNT); |
| 130 |
|
| 131 |
/* Initialize DMA descriptor */ |
| 132 |
bd_ptr[0].type_id = cpu_to_le32((DTYPE2 << 29) | (op << 19) | destid); |
| 133 |
bd_ptr[0].bcount = cpu_to_le32((sys_size << 26) | 0x04); |
| 134 |
bd_ptr[0].raddr_lo = cpu_to_le32((hopcount << 24) | offset); |
| 135 |
bd_ptr[0].raddr_hi = 0; |
| 136 |
if (do_wr) |
| 137 |
bd_ptr[0].data[0] = cpu_to_be32p(data); |
| 138 |
else |
| 139 |
bd_ptr[0].data[0] = 0xffffffff; |
| 140 |
|
| 141 |
mb(); |
| 142 |
|
| 143 |
/* Start DMA operation */ |
| 144 |
iowrite32(rd_count + 2, regs + TSI721_DMAC_DWRCNT); |
| 145 |
ioread32(regs + TSI721_DMAC_DWRCNT); |
| 146 |
i = 0; |
| 147 |
|
| 148 |
/* Wait until DMA transfer is finished */ |
| 149 |
while ((ch_stat = ioread32(regs + TSI721_DMAC_STS)) |
| 150 |
& TSI721_DMAC_STS_RUN) { |
| 151 |
udelay(1); |
| 152 |
if (++i >= 5000000) { |
| 153 |
tsi_debug(MAINT, &priv->pdev->dev, |
| 154 |
"DMA[%d] read timeout ch_status=%x", |
| 155 |
priv->mdma.ch_id, ch_stat); |
| 156 |
if (!do_wr) |
| 157 |
*data = 0xffffffff; |
| 158 |
err = -EIO; |
| 159 |
goto err_out; |
| 160 |
} |
| 161 |
} |
| 162 |
|
| 163 |
if (ch_stat & TSI721_DMAC_STS_ABORT) { |
| 164 |
/* If DMA operation aborted due to error, |
| 165 |
* reinitialize DMA channel |
| 166 |
*/ |
| 167 |
tsi_debug(MAINT, &priv->pdev->dev, "DMA ABORT ch_stat=%x", |
| 168 |
ch_stat); |
| 169 |
tsi_debug(MAINT, &priv->pdev->dev, |
| 170 |
"OP=%d : destid=%x hc=%x off=%x", |
| 171 |
do_wr ? MAINT_WR : MAINT_RD, |
| 172 |
destid, hopcount, offset); |
| 173 |
iowrite32(TSI721_DMAC_INT_ALL, regs + TSI721_DMAC_INT); |
| 174 |
iowrite32(TSI721_DMAC_CTL_INIT, regs + TSI721_DMAC_CTL); |
| 175 |
udelay(10); |
| 176 |
iowrite32(0, regs + TSI721_DMAC_DWRCNT); |
| 177 |
udelay(1); |
| 178 |
if (!do_wr) |
| 179 |
*data = 0xffffffff; |
| 180 |
err = -EIO; |
| 181 |
goto err_out; |
| 182 |
} |
| 183 |
|
| 184 |
if (!do_wr) |
| 185 |
*data = be32_to_cpu(bd_ptr[0].data[0]); |
| 186 |
|
| 187 |
/* |
| 188 |
* Update descriptor status FIFO RD pointer. |
| 189 |
* NOTE: Skipping check and clear FIFO entries because we are waiting |
| 190 |
* for transfer to be completed. |
| 191 |
*/ |
| 192 |
swr_ptr = ioread32(regs + TSI721_DMAC_DSWP); |
| 193 |
iowrite32(swr_ptr, regs + TSI721_DMAC_DSRP); |
| 194 |
|
| 195 |
err_out: |
| 196 |
spin_unlock_irqrestore(&tsi721_maint_lock, flags); |
| 197 |
|
| 198 |
return err; |
| 199 |
} |
| 200 |
|
| 201 |
/** |
| 202 |
* tsi721_cread_dma - Generate a RapidIO maintenance read transaction |
| 203 |
* using Tsi721 BDMA engine. |
| 204 |
* @mport: RapidIO master port control structure |
| 205 |
* @index: ID of RapdiIO interface |
| 206 |
* @destid: Destination ID of transaction |
| 207 |
* @hopcount: Number of hops to target device |
| 208 |
* @offset: Offset into configuration space |
| 209 |
* @len: Length (in bytes) of the maintenance transaction |
| 210 |
* @data: Location to be read into |
| 211 |
* |
| 212 |
* Generates a RapidIO maintenance read transaction. |
| 213 |
* Returns: %0 on success and %-EINVAL or %-EFAULT on failure. |
| 214 |
*/ |
| 215 |
static int tsi721_cread_dma(struct rio_mport *mport, int index, u16 destid, |
| 216 |
u8 hopcount, u32 offset, int len, u32 *data) |
| 217 |
{ |
| 218 |
struct tsi721_device *priv = mport->priv; |
| 219 |
|
| 220 |
return tsi721_maint_dma(priv, mport->sys_size, destid, hopcount, |
| 221 |
offset, len, data, 0); |
| 222 |
} |
| 223 |
|
| 224 |
/** |
| 225 |
* tsi721_cwrite_dma - Generate a RapidIO maintenance write transaction |
| 226 |
* using Tsi721 BDMA engine |
| 227 |
* @mport: RapidIO master port control structure |
| 228 |
* @index: ID of RapdiIO interface |
| 229 |
* @destid: Destination ID of transaction |
| 230 |
* @hopcount: Number of hops to target device |
| 231 |
* @offset: Offset into configuration space |
| 232 |
* @len: Length (in bytes) of the maintenance transaction |
| 233 |
* @data: Value to be written |
| 234 |
* |
| 235 |
* Generates a RapidIO maintenance write transaction. |
| 236 |
* Returns: %0 on success and %-EINVAL or %-EFAULT on failure. |
| 237 |
*/ |
| 238 |
static int tsi721_cwrite_dma(struct rio_mport *mport, int index, u16 destid, |
| 239 |
u8 hopcount, u32 offset, int len, u32 data) |
| 240 |
{ |
| 241 |
struct tsi721_device *priv = mport->priv; |
| 242 |
u32 temp = data; |
| 243 |
|
| 244 |
return tsi721_maint_dma(priv, mport->sys_size, destid, hopcount, |
| 245 |
offset, len, &temp, 1); |
| 246 |
} |
| 247 |
|
| 248 |
/** |
| 249 |
* tsi721_pw_handler - Tsi721 inbound port-write interrupt handler |
| 250 |
* @priv: tsi721 device private structure |
| 251 |
* |
| 252 |
* Handles inbound port-write interrupts. Copies PW message from an internal |
| 253 |
* buffer into PW message FIFO and schedules deferred routine to process |
| 254 |
* queued messages. |
| 255 |
* |
| 256 |
* Returns: %0 |
| 257 |
*/ |
| 258 |
static int |
| 259 |
tsi721_pw_handler(struct tsi721_device *priv) |
| 260 |
{ |
| 261 |
u32 pw_stat; |
| 262 |
u32 pw_buf[TSI721_RIO_PW_MSG_SIZE/sizeof(u32)]; |
| 263 |
|
| 264 |
|
| 265 |
pw_stat = ioread32(priv->regs + TSI721_RIO_PW_RX_STAT); |
| 266 |
|
| 267 |
if (pw_stat & TSI721_RIO_PW_RX_STAT_PW_VAL) { |
| 268 |
pw_buf[0] = ioread32(priv->regs + TSI721_RIO_PW_RX_CAPT(0)); |
| 269 |
pw_buf[1] = ioread32(priv->regs + TSI721_RIO_PW_RX_CAPT(1)); |
| 270 |
pw_buf[2] = ioread32(priv->regs + TSI721_RIO_PW_RX_CAPT(2)); |
| 271 |
pw_buf[3] = ioread32(priv->regs + TSI721_RIO_PW_RX_CAPT(3)); |
| 272 |
|
| 273 |
/* Queue PW message (if there is room in FIFO), |
| 274 |
* otherwise discard it. |
| 275 |
*/ |
| 276 |
spin_lock(&priv->pw_fifo_lock); |
| 277 |
if (kfifo_avail(&priv->pw_fifo) >= TSI721_RIO_PW_MSG_SIZE) |
| 278 |
kfifo_in(&priv->pw_fifo, pw_buf, |
| 279 |
TSI721_RIO_PW_MSG_SIZE); |
| 280 |
else |
| 281 |
priv->pw_discard_count++; |
| 282 |
spin_unlock(&priv->pw_fifo_lock); |
| 283 |
} |
| 284 |
|
| 285 |
/* Clear pending PW interrupts */ |
| 286 |
iowrite32(TSI721_RIO_PW_RX_STAT_PW_DISC | TSI721_RIO_PW_RX_STAT_PW_VAL, |
| 287 |
priv->regs + TSI721_RIO_PW_RX_STAT); |
| 288 |
|
| 289 |
schedule_work(&priv->pw_work); |
| 290 |
|
| 291 |
return 0; |
| 292 |
} |
| 293 |
|
| 294 |
static void tsi721_pw_dpc(struct work_struct *work) |
| 295 |
{ |
| 296 |
struct tsi721_device *priv = container_of(work, struct tsi721_device, |
| 297 |
pw_work); |
| 298 |
union rio_pw_msg pwmsg; |
| 299 |
|
| 300 |
/* |
| 301 |
* Process port-write messages |
| 302 |
*/ |
| 303 |
while (kfifo_out_spinlocked(&priv->pw_fifo, (unsigned char *)&pwmsg, |
| 304 |
TSI721_RIO_PW_MSG_SIZE, &priv->pw_fifo_lock)) { |
| 305 |
/* Pass the port-write message to RIO core for processing */ |
| 306 |
rio_inb_pwrite_handler(&priv->mport, &pwmsg); |
| 307 |
} |
| 308 |
} |
| 309 |
|
| 310 |
/** |
| 311 |
* tsi721_pw_enable - enable/disable port-write interface init |
| 312 |
* @mport: Master port implementing the port write unit |
| 313 |
* @enable: 1=enable; 0=disable port-write message handling |
| 314 |
* |
| 315 |
* Returns: %0 |
| 316 |
*/ |
| 317 |
static int tsi721_pw_enable(struct rio_mport *mport, int enable) |
| 318 |
{ |
| 319 |
struct tsi721_device *priv = mport->priv; |
| 320 |
u32 rval; |
| 321 |
|
| 322 |
rval = ioread32(priv->regs + TSI721_RIO_EM_INT_ENABLE); |
| 323 |
|
| 324 |
if (enable) |
| 325 |
rval |= TSI721_RIO_EM_INT_ENABLE_PW_RX; |
| 326 |
else |
| 327 |
rval &= ~TSI721_RIO_EM_INT_ENABLE_PW_RX; |
| 328 |
|
| 329 |
/* Clear pending PW interrupts */ |
| 330 |
iowrite32(TSI721_RIO_PW_RX_STAT_PW_DISC | TSI721_RIO_PW_RX_STAT_PW_VAL, |
| 331 |
priv->regs + TSI721_RIO_PW_RX_STAT); |
| 332 |
/* Update enable bits */ |
| 333 |
iowrite32(rval, priv->regs + TSI721_RIO_EM_INT_ENABLE); |
| 334 |
|
| 335 |
return 0; |
| 336 |
} |
| 337 |
|
| 338 |
/** |
| 339 |
* tsi721_dsend - Send a RapidIO doorbell |
| 340 |
* @mport: RapidIO master port info |
| 341 |
* @index: ID of RapidIO interface |
| 342 |
* @destid: Destination ID of target device |
| 343 |
* @data: 16-bit info field of RapidIO doorbell |
| 344 |
* |
| 345 |
* Sends a RapidIO doorbell message. |
| 346 |
* |
| 347 |
* Returns: %0 |
| 348 |
*/ |
| 349 |
static int tsi721_dsend(struct rio_mport *mport, int index, |
| 350 |
u16 destid, u16 data) |
| 351 |
{ |
| 352 |
struct tsi721_device *priv = mport->priv; |
| 353 |
u32 offset; |
| 354 |
|
| 355 |
offset = (((mport->sys_size) ? RIO_TT_CODE_16 : RIO_TT_CODE_8) << 18) | |
| 356 |
(destid << 2); |
| 357 |
|
| 358 |
tsi_debug(DBELL, &priv->pdev->dev, |
| 359 |
"Send Doorbell 0x%04x to destID 0x%x", data, destid); |
| 360 |
iowrite16be(data, priv->odb_base + offset); |
| 361 |
|
| 362 |
return 0; |
| 363 |
} |
| 364 |
|
| 365 |
/** |
| 366 |
* tsi721_dbell_handler - Tsi721 doorbell interrupt handler |
| 367 |
* @priv: tsi721 device-specific data structure |
| 368 |
* |
| 369 |
* Handles inbound doorbell interrupts. Copies doorbell entry from an internal |
| 370 |
* buffer into DB message FIFO and schedules deferred routine to process |
| 371 |
* queued DBs. |
| 372 |
* |
| 373 |
* Returns: %0 |
| 374 |
*/ |
| 375 |
static int |
| 376 |
tsi721_dbell_handler(struct tsi721_device *priv) |
| 377 |
{ |
| 378 |
u32 regval; |
| 379 |
|
| 380 |
/* Disable IDB interrupts */ |
| 381 |
regval = ioread32(priv->regs + TSI721_SR_CHINTE(IDB_QUEUE)); |
| 382 |
regval &= ~TSI721_SR_CHINT_IDBQRCV; |
| 383 |
iowrite32(regval, |
| 384 |
priv->regs + TSI721_SR_CHINTE(IDB_QUEUE)); |
| 385 |
|
| 386 |
schedule_work(&priv->idb_work); |
| 387 |
|
| 388 |
return 0; |
| 389 |
} |
| 390 |
|
| 391 |
static void tsi721_db_dpc(struct work_struct *work) |
| 392 |
{ |
| 393 |
struct tsi721_device *priv = container_of(work, struct tsi721_device, |
| 394 |
idb_work); |
| 395 |
struct rio_mport *mport; |
| 396 |
struct rio_dbell *dbell; |
| 397 |
int found = 0; |
| 398 |
u32 wr_ptr, rd_ptr; |
| 399 |
u64 *idb_entry; |
| 400 |
u32 regval; |
| 401 |
union { |
| 402 |
u64 msg; |
| 403 |
u8 bytes[8]; |
| 404 |
} idb; |
| 405 |
|
| 406 |
/* |
| 407 |
* Process queued inbound doorbells |
| 408 |
*/ |
| 409 |
mport = &priv->mport; |
| 410 |
|
| 411 |
wr_ptr = ioread32(priv->regs + TSI721_IDQ_WP(IDB_QUEUE)) % IDB_QSIZE; |
| 412 |
rd_ptr = ioread32(priv->regs + TSI721_IDQ_RP(IDB_QUEUE)) % IDB_QSIZE; |
| 413 |
|
| 414 |
while (wr_ptr != rd_ptr) { |
| 415 |
idb_entry = (u64 *)(priv->idb_base + |
| 416 |
(TSI721_IDB_ENTRY_SIZE * rd_ptr)); |
| 417 |
rd_ptr++; |
| 418 |
rd_ptr %= IDB_QSIZE; |
| 419 |
idb.msg = *idb_entry; |
| 420 |
*idb_entry = 0; |
| 421 |
|
| 422 |
/* Process one doorbell */ |
| 423 |
list_for_each_entry(dbell, &mport->dbells, node) { |
| 424 |
if ((dbell->res->start <= DBELL_INF(idb.bytes)) && |
| 425 |
(dbell->res->end >= DBELL_INF(idb.bytes))) { |
| 426 |
found = 1; |
| 427 |
break; |
| 428 |
} |
| 429 |
} |
| 430 |
|
| 431 |
if (found) { |
| 432 |
dbell->dinb(mport, dbell->dev_id, DBELL_SID(idb.bytes), |
| 433 |
DBELL_TID(idb.bytes), DBELL_INF(idb.bytes)); |
| 434 |
} else { |
| 435 |
tsi_debug(DBELL, &priv->pdev->dev, |
| 436 |
"spurious IDB sid %2.2x tid %2.2x info %4.4x", |
| 437 |
DBELL_SID(idb.bytes), DBELL_TID(idb.bytes), |
| 438 |
DBELL_INF(idb.bytes)); |
| 439 |
} |
| 440 |
|
| 441 |
wr_ptr = ioread32(priv->regs + |
| 442 |
TSI721_IDQ_WP(IDB_QUEUE)) % IDB_QSIZE; |
| 443 |
} |
| 444 |
|
| 445 |
iowrite32(rd_ptr & (IDB_QSIZE - 1), |
| 446 |
priv->regs + TSI721_IDQ_RP(IDB_QUEUE)); |
| 447 |
|
| 448 |
/* Re-enable IDB interrupts */ |
| 449 |
regval = ioread32(priv->regs + TSI721_SR_CHINTE(IDB_QUEUE)); |
| 450 |
regval |= TSI721_SR_CHINT_IDBQRCV; |
| 451 |
iowrite32(regval, |
| 452 |
priv->regs + TSI721_SR_CHINTE(IDB_QUEUE)); |
| 453 |
|
| 454 |
wr_ptr = ioread32(priv->regs + TSI721_IDQ_WP(IDB_QUEUE)) % IDB_QSIZE; |
| 455 |
if (wr_ptr != rd_ptr) |
| 456 |
schedule_work(&priv->idb_work); |
| 457 |
} |
| 458 |
|
| 459 |
/** |
| 460 |
* tsi721_irqhandler - Tsi721 interrupt handler |
| 461 |
* @irq: Linux interrupt number |
| 462 |
* @ptr: Pointer to interrupt-specific data (tsi721_device structure) |
| 463 |
* |
| 464 |
* Handles Tsi721 interrupts signaled using MSI and INTA. Checks reported |
| 465 |
* interrupt events and calls an event-specific handler(s). |
| 466 |
* |
| 467 |
* Returns: %IRQ_HANDLED or %IRQ_NONE |
| 468 |
*/ |
| 469 |
static irqreturn_t tsi721_irqhandler(int irq, void *ptr) |
| 470 |
{ |
| 471 |
struct tsi721_device *priv = (struct tsi721_device *)ptr; |
| 472 |
u32 dev_int; |
| 473 |
u32 dev_ch_int; |
| 474 |
u32 intval; |
| 475 |
u32 ch_inte; |
| 476 |
|
| 477 |
/* For MSI mode disable all device-level interrupts */ |
| 478 |
if (priv->flags & TSI721_USING_MSI) |
| 479 |
iowrite32(0, priv->regs + TSI721_DEV_INTE); |
| 480 |
|
| 481 |
dev_int = ioread32(priv->regs + TSI721_DEV_INT); |
| 482 |
if (!dev_int) |
| 483 |
return IRQ_NONE; |
| 484 |
|
| 485 |
dev_ch_int = ioread32(priv->regs + TSI721_DEV_CHAN_INT); |
| 486 |
|
| 487 |
if (dev_int & TSI721_DEV_INT_SR2PC_CH) { |
| 488 |
/* Service SR2PC Channel interrupts */ |
| 489 |
if (dev_ch_int & TSI721_INT_SR2PC_CHAN(IDB_QUEUE)) { |
| 490 |
/* Service Inbound Doorbell interrupt */ |
| 491 |
intval = ioread32(priv->regs + |
| 492 |
TSI721_SR_CHINT(IDB_QUEUE)); |
| 493 |
if (intval & TSI721_SR_CHINT_IDBQRCV) |
| 494 |
tsi721_dbell_handler(priv); |
| 495 |
else |
| 496 |
tsi_info(&priv->pdev->dev, |
| 497 |
"Unsupported SR_CH_INT %x", intval); |
| 498 |
|
| 499 |
/* Clear interrupts */ |
| 500 |
iowrite32(intval, |
| 501 |
priv->regs + TSI721_SR_CHINT(IDB_QUEUE)); |
| 502 |
ioread32(priv->regs + TSI721_SR_CHINT(IDB_QUEUE)); |
| 503 |
} |
| 504 |
} |
| 505 |
|
| 506 |
if (dev_int & TSI721_DEV_INT_SMSG_CH) { |
| 507 |
int ch; |
| 508 |
|
| 509 |
/* |
| 510 |
* Service channel interrupts from Messaging Engine |
| 511 |
*/ |
| 512 |
|
| 513 |
if (dev_ch_int & TSI721_INT_IMSG_CHAN_M) { /* Inbound Msg */ |
| 514 |
/* Disable signaled OB MSG Channel interrupts */ |
| 515 |
ch_inte = ioread32(priv->regs + TSI721_DEV_CHAN_INTE); |
| 516 |
ch_inte &= ~(dev_ch_int & TSI721_INT_IMSG_CHAN_M); |
| 517 |
iowrite32(ch_inte, priv->regs + TSI721_DEV_CHAN_INTE); |
| 518 |
|
| 519 |
/* |
| 520 |
* Process Inbound Message interrupt for each MBOX |
| 521 |
*/ |
| 522 |
for (ch = 4; ch < RIO_MAX_MBOX + 4; ch++) { |
| 523 |
if (!(dev_ch_int & TSI721_INT_IMSG_CHAN(ch))) |
| 524 |
continue; |
| 525 |
tsi721_imsg_handler(priv, ch); |
| 526 |
} |
| 527 |
} |
| 528 |
|
| 529 |
if (dev_ch_int & TSI721_INT_OMSG_CHAN_M) { /* Outbound Msg */ |
| 530 |
/* Disable signaled OB MSG Channel interrupts */ |
| 531 |
ch_inte = ioread32(priv->regs + TSI721_DEV_CHAN_INTE); |
| 532 |
ch_inte &= ~(dev_ch_int & TSI721_INT_OMSG_CHAN_M); |
| 533 |
iowrite32(ch_inte, priv->regs + TSI721_DEV_CHAN_INTE); |
| 534 |
|
| 535 |
/* |
| 536 |
* Process Outbound Message interrupts for each MBOX |
| 537 |
*/ |
| 538 |
|
| 539 |
for (ch = 0; ch < RIO_MAX_MBOX; ch++) { |
| 540 |
if (!(dev_ch_int & TSI721_INT_OMSG_CHAN(ch))) |
| 541 |
continue; |
| 542 |
tsi721_omsg_handler(priv, ch); |
| 543 |
} |
| 544 |
} |
| 545 |
} |
| 546 |
|
| 547 |
if (dev_int & TSI721_DEV_INT_SRIO) { |
| 548 |
/* Service SRIO MAC interrupts */ |
| 549 |
intval = ioread32(priv->regs + TSI721_RIO_EM_INT_STAT); |
| 550 |
if (intval & TSI721_RIO_EM_INT_STAT_PW_RX) |
| 551 |
tsi721_pw_handler(priv); |
| 552 |
} |
| 553 |
|
| 554 |
#ifdef CONFIG_RAPIDIO_DMA_ENGINE |
| 555 |
if (dev_int & TSI721_DEV_INT_BDMA_CH) { |
| 556 |
int ch; |
| 557 |
|
| 558 |
if (dev_ch_int & TSI721_INT_BDMA_CHAN_M) { |
| 559 |
tsi_debug(DMA, &priv->pdev->dev, |
| 560 |
"IRQ from DMA channel 0x%08x", dev_ch_int); |
| 561 |
|
| 562 |
for (ch = 0; ch < TSI721_DMA_MAXCH; ch++) { |
| 563 |
if (!(dev_ch_int & TSI721_INT_BDMA_CHAN(ch))) |
| 564 |
continue; |
| 565 |
tsi721_bdma_handler(&priv->bdma[ch]); |
| 566 |
} |
| 567 |
} |
| 568 |
} |
| 569 |
#endif |
| 570 |
|
| 571 |
/* For MSI mode re-enable device-level interrupts */ |
| 572 |
if (priv->flags & TSI721_USING_MSI) { |
| 573 |
dev_int = TSI721_DEV_INT_SR2PC_CH | TSI721_DEV_INT_SRIO | |
| 574 |
TSI721_DEV_INT_SMSG_CH | TSI721_DEV_INT_BDMA_CH; |
| 575 |
iowrite32(dev_int, priv->regs + TSI721_DEV_INTE); |
| 576 |
} |
| 577 |
|
| 578 |
return IRQ_HANDLED; |
| 579 |
} |
| 580 |
|
| 581 |
static void tsi721_interrupts_init(struct tsi721_device *priv) |
| 582 |
{ |
| 583 |
u32 intr; |
| 584 |
|
| 585 |
/* Enable IDB interrupts */ |
| 586 |
iowrite32(TSI721_SR_CHINT_ALL, |
| 587 |
priv->regs + TSI721_SR_CHINT(IDB_QUEUE)); |
| 588 |
iowrite32(TSI721_SR_CHINT_IDBQRCV, |
| 589 |
priv->regs + TSI721_SR_CHINTE(IDB_QUEUE)); |
| 590 |
|
| 591 |
/* Enable SRIO MAC interrupts */ |
| 592 |
iowrite32(TSI721_RIO_EM_DEV_INT_EN_INT, |
| 593 |
priv->regs + TSI721_RIO_EM_DEV_INT_EN); |
| 594 |
|
| 595 |
/* Enable interrupts from channels in use */ |
| 596 |
#ifdef CONFIG_RAPIDIO_DMA_ENGINE |
| 597 |
intr = TSI721_INT_SR2PC_CHAN(IDB_QUEUE) | |
| 598 |
(TSI721_INT_BDMA_CHAN_M & |
| 599 |
~TSI721_INT_BDMA_CHAN(TSI721_DMACH_MAINT)); |
| 600 |
#else |
| 601 |
intr = TSI721_INT_SR2PC_CHAN(IDB_QUEUE); |
| 602 |
#endif |
| 603 |
iowrite32(intr, priv->regs + TSI721_DEV_CHAN_INTE); |
| 604 |
|
| 605 |
if (priv->flags & TSI721_USING_MSIX) |
| 606 |
intr = TSI721_DEV_INT_SRIO; |
| 607 |
else |
| 608 |
intr = TSI721_DEV_INT_SR2PC_CH | TSI721_DEV_INT_SRIO | |
| 609 |
TSI721_DEV_INT_SMSG_CH | TSI721_DEV_INT_BDMA_CH; |
| 610 |
|
| 611 |
iowrite32(intr, priv->regs + TSI721_DEV_INTE); |
| 612 |
ioread32(priv->regs + TSI721_DEV_INTE); |
| 613 |
} |
| 614 |
|
| 615 |
#ifdef CONFIG_PCI_MSI |
| 616 |
/** |
| 617 |
* tsi721_omsg_msix - MSI-X interrupt handler for outbound messaging |
| 618 |
* @irq: Linux interrupt number |
| 619 |
* @ptr: Pointer to interrupt-specific data (tsi721_device structure) |
| 620 |
* |
| 621 |
* Handles outbound messaging interrupts signaled using MSI-X. |
| 622 |
* |
| 623 |
* Returns: %IRQ_HANDLED |
| 624 |
*/ |
| 625 |
static irqreturn_t tsi721_omsg_msix(int irq, void *ptr) |
| 626 |
{ |
| 627 |
struct tsi721_device *priv = (struct tsi721_device *)ptr; |
| 628 |
int mbox; |
| 629 |
|
| 630 |
mbox = (irq - priv->msix[TSI721_VECT_OMB0_DONE].vector) % RIO_MAX_MBOX; |
| 631 |
tsi721_omsg_handler(priv, mbox); |
| 632 |
return IRQ_HANDLED; |
| 633 |
} |
| 634 |
|
| 635 |
/** |
| 636 |
* tsi721_imsg_msix - MSI-X interrupt handler for inbound messaging |
| 637 |
* @irq: Linux interrupt number |
| 638 |
* @ptr: Pointer to interrupt-specific data (tsi721_device structure) |
| 639 |
* |
| 640 |
* Handles inbound messaging interrupts signaled using MSI-X. |
| 641 |
* |
| 642 |
* Returns: %IRQ_HANDLED |
| 643 |
*/ |
| 644 |
static irqreturn_t tsi721_imsg_msix(int irq, void *ptr) |
| 645 |
{ |
| 646 |
struct tsi721_device *priv = (struct tsi721_device *)ptr; |
| 647 |
int mbox; |
| 648 |
|
| 649 |
mbox = (irq - priv->msix[TSI721_VECT_IMB0_RCV].vector) % RIO_MAX_MBOX; |
| 650 |
tsi721_imsg_handler(priv, mbox + 4); |
| 651 |
return IRQ_HANDLED; |
| 652 |
} |
| 653 |
|
| 654 |
/** |
| 655 |
* tsi721_srio_msix - Tsi721 MSI-X SRIO MAC interrupt handler |
| 656 |
* @irq: Linux interrupt number |
| 657 |
* @ptr: Pointer to interrupt-specific data (tsi721_device structure) |
| 658 |
* |
| 659 |
* Handles Tsi721 interrupts from SRIO MAC. |
| 660 |
* |
| 661 |
* Returns: %IRQ_HANDLED |
| 662 |
*/ |
| 663 |
static irqreturn_t tsi721_srio_msix(int irq, void *ptr) |
| 664 |
{ |
| 665 |
struct tsi721_device *priv = (struct tsi721_device *)ptr; |
| 666 |
u32 srio_int; |
| 667 |
|
| 668 |
/* Service SRIO MAC interrupts */ |
| 669 |
srio_int = ioread32(priv->regs + TSI721_RIO_EM_INT_STAT); |
| 670 |
if (srio_int & TSI721_RIO_EM_INT_STAT_PW_RX) |
| 671 |
tsi721_pw_handler(priv); |
| 672 |
|
| 673 |
return IRQ_HANDLED; |
| 674 |
} |
| 675 |
|
| 676 |
/** |
| 677 |
* tsi721_sr2pc_ch_msix - Tsi721 MSI-X SR2PC Channel interrupt handler |
| 678 |
* @irq: Linux interrupt number |
| 679 |
* @ptr: Pointer to interrupt-specific data (tsi721_device structure) |
| 680 |
* |
| 681 |
* Handles Tsi721 interrupts from SR2PC Channel. |
| 682 |
* NOTE: At this moment services only one SR2PC channel associated with inbound |
| 683 |
* doorbells. |
| 684 |
* |
| 685 |
* Returns: %IRQ_HANDLED |
| 686 |
*/ |
| 687 |
static irqreturn_t tsi721_sr2pc_ch_msix(int irq, void *ptr) |
| 688 |
{ |
| 689 |
struct tsi721_device *priv = (struct tsi721_device *)ptr; |
| 690 |
u32 sr_ch_int; |
| 691 |
|
| 692 |
/* Service Inbound DB interrupt from SR2PC channel */ |
| 693 |
sr_ch_int = ioread32(priv->regs + TSI721_SR_CHINT(IDB_QUEUE)); |
| 694 |
if (sr_ch_int & TSI721_SR_CHINT_IDBQRCV) |
| 695 |
tsi721_dbell_handler(priv); |
| 696 |
|
| 697 |
/* Clear interrupts */ |
| 698 |
iowrite32(sr_ch_int, priv->regs + TSI721_SR_CHINT(IDB_QUEUE)); |
| 699 |
/* Read back to ensure that interrupt was cleared */ |
| 700 |
sr_ch_int = ioread32(priv->regs + TSI721_SR_CHINT(IDB_QUEUE)); |
| 701 |
|
| 702 |
return IRQ_HANDLED; |
| 703 |
} |
| 704 |
|
| 705 |
/** |
| 706 |
* tsi721_request_msix - register interrupt service for MSI-X mode. |
| 707 |
* @priv: tsi721 device-specific data structure |
| 708 |
* |
| 709 |
* Registers MSI-X interrupt service routines for interrupts that are active |
| 710 |
* immediately after mport initialization. Messaging interrupt service routines |
| 711 |
* should be registered during corresponding open requests. |
| 712 |
* |
| 713 |
* Returns: %0 on success or -errno value on failure. |
| 714 |
*/ |
| 715 |
static int tsi721_request_msix(struct tsi721_device *priv) |
| 716 |
{ |
| 717 |
int err = 0; |
| 718 |
|
| 719 |
err = request_irq(priv->msix[TSI721_VECT_IDB].vector, |
| 720 |
tsi721_sr2pc_ch_msix, 0, |
| 721 |
priv->msix[TSI721_VECT_IDB].irq_name, (void *)priv); |
| 722 |
if (err) |
| 723 |
return err; |
| 724 |
|
| 725 |
err = request_irq(priv->msix[TSI721_VECT_PWRX].vector, |
| 726 |
tsi721_srio_msix, 0, |
| 727 |
priv->msix[TSI721_VECT_PWRX].irq_name, (void *)priv); |
| 728 |
if (err) { |
| 729 |
free_irq(priv->msix[TSI721_VECT_IDB].vector, (void *)priv); |
| 730 |
return err; |
| 731 |
} |
| 732 |
|
| 733 |
return 0; |
| 734 |
} |
| 735 |
|
| 736 |
/** |
| 737 |
* tsi721_enable_msix - Attempts to enable MSI-X support for Tsi721. |
| 738 |
* @priv: pointer to tsi721 private data |
| 739 |
* |
| 740 |
* Configures MSI-X support for Tsi721. Supports only an exact number |
| 741 |
* of requested vectors. |
| 742 |
* |
| 743 |
* Returns: %0 on success or -errno value on failure. |
| 744 |
*/ |
| 745 |
static int tsi721_enable_msix(struct tsi721_device *priv) |
| 746 |
{ |
| 747 |
struct msix_entry entries[TSI721_VECT_MAX]; |
| 748 |
int err; |
| 749 |
int i; |
| 750 |
|
| 751 |
entries[TSI721_VECT_IDB].entry = TSI721_MSIX_SR2PC_IDBQ_RCV(IDB_QUEUE); |
| 752 |
entries[TSI721_VECT_PWRX].entry = TSI721_MSIX_SRIO_MAC_INT; |
| 753 |
|
| 754 |
/* |
| 755 |
* Initialize MSI-X entries for Messaging Engine: |
| 756 |
* this driver supports four RIO mailboxes (inbound and outbound) |
| 757 |
* NOTE: Inbound message MBOX 0...4 use IB channels 4...7. Therefore |
| 758 |
* offset +4 is added to IB MBOX number. |
| 759 |
*/ |
| 760 |
for (i = 0; i < RIO_MAX_MBOX; i++) { |
| 761 |
entries[TSI721_VECT_IMB0_RCV + i].entry = |
| 762 |
TSI721_MSIX_IMSG_DQ_RCV(i + 4); |
| 763 |
entries[TSI721_VECT_IMB0_INT + i].entry = |
| 764 |
TSI721_MSIX_IMSG_INT(i + 4); |
| 765 |
entries[TSI721_VECT_OMB0_DONE + i].entry = |
| 766 |
TSI721_MSIX_OMSG_DONE(i); |
| 767 |
entries[TSI721_VECT_OMB0_INT + i].entry = |
| 768 |
TSI721_MSIX_OMSG_INT(i); |
| 769 |
} |
| 770 |
|
| 771 |
#ifdef CONFIG_RAPIDIO_DMA_ENGINE |
| 772 |
/* |
| 773 |
* Initialize MSI-X entries for Block DMA Engine: |
| 774 |
* this driver supports XXX DMA channels |
| 775 |
* (one is reserved for SRIO maintenance transactions) |
| 776 |
*/ |
| 777 |
for (i = 0; i < TSI721_DMA_CHNUM; i++) { |
| 778 |
entries[TSI721_VECT_DMA0_DONE + i].entry = |
| 779 |
TSI721_MSIX_DMACH_DONE(i); |
| 780 |
entries[TSI721_VECT_DMA0_INT + i].entry = |
| 781 |
TSI721_MSIX_DMACH_INT(i); |
| 782 |
} |
| 783 |
#endif /* CONFIG_RAPIDIO_DMA_ENGINE */ |
| 784 |
|
| 785 |
err = pci_enable_msix_exact(priv->pdev, entries, ARRAY_SIZE(entries)); |
| 786 |
if (err) { |
| 787 |
tsi_err(&priv->pdev->dev, |
| 788 |
"Failed to enable MSI-X (err=%d)", err); |
| 789 |
return err; |
| 790 |
} |
| 791 |
|
| 792 |
/* |
| 793 |
* Copy MSI-X vector information into tsi721 private structure |
| 794 |
*/ |
| 795 |
priv->msix[TSI721_VECT_IDB].vector = entries[TSI721_VECT_IDB].vector; |
| 796 |
snprintf(priv->msix[TSI721_VECT_IDB].irq_name, IRQ_DEVICE_NAME_MAX, |
| 797 |
DRV_NAME "-idb@pci:%s", pci_name(priv->pdev)); |
| 798 |
priv->msix[TSI721_VECT_PWRX].vector = entries[TSI721_VECT_PWRX].vector; |
| 799 |
snprintf(priv->msix[TSI721_VECT_PWRX].irq_name, IRQ_DEVICE_NAME_MAX, |
| 800 |
DRV_NAME "-pwrx@pci:%s", pci_name(priv->pdev)); |
| 801 |
|
| 802 |
for (i = 0; i < RIO_MAX_MBOX; i++) { |
| 803 |
priv->msix[TSI721_VECT_IMB0_RCV + i].vector = |
| 804 |
entries[TSI721_VECT_IMB0_RCV + i].vector; |
| 805 |
snprintf(priv->msix[TSI721_VECT_IMB0_RCV + i].irq_name, |
| 806 |
IRQ_DEVICE_NAME_MAX, DRV_NAME "-imbr%d@pci:%s", |
| 807 |
i, pci_name(priv->pdev)); |
| 808 |
|
| 809 |
priv->msix[TSI721_VECT_IMB0_INT + i].vector = |
| 810 |
entries[TSI721_VECT_IMB0_INT + i].vector; |
| 811 |
snprintf(priv->msix[TSI721_VECT_IMB0_INT + i].irq_name, |
| 812 |
IRQ_DEVICE_NAME_MAX, DRV_NAME "-imbi%d@pci:%s", |
| 813 |
i, pci_name(priv->pdev)); |
| 814 |
|
| 815 |
priv->msix[TSI721_VECT_OMB0_DONE + i].vector = |
| 816 |
entries[TSI721_VECT_OMB0_DONE + i].vector; |
| 817 |
snprintf(priv->msix[TSI721_VECT_OMB0_DONE + i].irq_name, |
| 818 |
IRQ_DEVICE_NAME_MAX, DRV_NAME "-ombd%d@pci:%s", |
| 819 |
i, pci_name(priv->pdev)); |
| 820 |
|
| 821 |
priv->msix[TSI721_VECT_OMB0_INT + i].vector = |
| 822 |
entries[TSI721_VECT_OMB0_INT + i].vector; |
| 823 |
snprintf(priv->msix[TSI721_VECT_OMB0_INT + i].irq_name, |
| 824 |
IRQ_DEVICE_NAME_MAX, DRV_NAME "-ombi%d@pci:%s", |
| 825 |
i, pci_name(priv->pdev)); |
| 826 |
} |
| 827 |
|
| 828 |
#ifdef CONFIG_RAPIDIO_DMA_ENGINE |
| 829 |
for (i = 0; i < TSI721_DMA_CHNUM; i++) { |
| 830 |
priv->msix[TSI721_VECT_DMA0_DONE + i].vector = |
| 831 |
entries[TSI721_VECT_DMA0_DONE + i].vector; |
| 832 |
snprintf(priv->msix[TSI721_VECT_DMA0_DONE + i].irq_name, |
| 833 |
IRQ_DEVICE_NAME_MAX, DRV_NAME "-dmad%d@pci:%s", |
| 834 |
i, pci_name(priv->pdev)); |
| 835 |
|
| 836 |
priv->msix[TSI721_VECT_DMA0_INT + i].vector = |
| 837 |
entries[TSI721_VECT_DMA0_INT + i].vector; |
| 838 |
snprintf(priv->msix[TSI721_VECT_DMA0_INT + i].irq_name, |
| 839 |
IRQ_DEVICE_NAME_MAX, DRV_NAME "-dmai%d@pci:%s", |
| 840 |
i, pci_name(priv->pdev)); |
| 841 |
} |
| 842 |
#endif /* CONFIG_RAPIDIO_DMA_ENGINE */ |
| 843 |
|
| 844 |
return 0; |
| 845 |
} |
| 846 |
#endif /* CONFIG_PCI_MSI */ |
| 847 |
|
| 848 |
static int tsi721_request_irq(struct tsi721_device *priv) |
| 849 |
{ |
| 850 |
int err; |
| 851 |
|
| 852 |
#ifdef CONFIG_PCI_MSI |
| 853 |
if (priv->flags & TSI721_USING_MSIX) |
| 854 |
err = tsi721_request_msix(priv); |
| 855 |
else |
| 856 |
#endif |
| 857 |
err = request_irq(priv->pdev->irq, tsi721_irqhandler, |
| 858 |
(priv->flags & TSI721_USING_MSI) ? 0 : IRQF_SHARED, |
| 859 |
DRV_NAME, (void *)priv); |
| 860 |
|
| 861 |
if (err) |
| 862 |
tsi_err(&priv->pdev->dev, |
| 863 |
"Unable to allocate interrupt, err=%d", err); |
| 864 |
|
| 865 |
return err; |
| 866 |
} |
| 867 |
|
| 868 |
static void tsi721_free_irq(struct tsi721_device *priv) |
| 869 |
{ |
| 870 |
#ifdef CONFIG_PCI_MSI |
| 871 |
if (priv->flags & TSI721_USING_MSIX) { |
| 872 |
free_irq(priv->msix[TSI721_VECT_IDB].vector, (void *)priv); |
| 873 |
free_irq(priv->msix[TSI721_VECT_PWRX].vector, (void *)priv); |
| 874 |
} else |
| 875 |
#endif |
| 876 |
free_irq(priv->pdev->irq, (void *)priv); |
| 877 |
} |
| 878 |
|
| 879 |
static int |
| 880 |
tsi721_obw_alloc(struct tsi721_device *priv, struct tsi721_obw_bar *pbar, |
| 881 |
u32 size, int *win_id) |
| 882 |
{ |
| 883 |
u64 win_base; |
| 884 |
u64 bar_base; |
| 885 |
u64 bar_end; |
| 886 |
u32 align; |
| 887 |
struct tsi721_ob_win *win; |
| 888 |
struct tsi721_ob_win *new_win = NULL; |
| 889 |
int new_win_idx = -1; |
| 890 |
int i = 0; |
| 891 |
|
| 892 |
bar_base = pbar->base; |
| 893 |
bar_end = bar_base + pbar->size; |
| 894 |
win_base = bar_base; |
| 895 |
align = size/TSI721_PC2SR_ZONES; |
| 896 |
|
| 897 |
while (i < TSI721_IBWIN_NUM) { |
| 898 |
for (i = 0; i < TSI721_IBWIN_NUM; i++) { |
| 899 |
if (!priv->ob_win[i].active) { |
| 900 |
if (new_win == NULL) { |
| 901 |
new_win = &priv->ob_win[i]; |
| 902 |
new_win_idx = i; |
| 903 |
} |
| 904 |
continue; |
| 905 |
} |
| 906 |
|
| 907 |
/* |
| 908 |
* If this window belongs to the current BAR check it |
| 909 |
* for overlap |
| 910 |
*/ |
| 911 |
win = &priv->ob_win[i]; |
| 912 |
|
| 913 |
if (win->base >= bar_base && win->base < bar_end) { |
| 914 |
if (win_base < (win->base + win->size) && |
| 915 |
(win_base + size) > win->base) { |
| 916 |
/* Overlap detected */ |
| 917 |
win_base = win->base + win->size; |
| 918 |
win_base = ALIGN(win_base, align); |
| 919 |
break; |
| 920 |
} |
| 921 |
} |
| 922 |
} |
| 923 |
} |
| 924 |
|
| 925 |
if (win_base + size > bar_end) |
| 926 |
return -ENOMEM; |
| 927 |
|
| 928 |
if (!new_win) { |
| 929 |
tsi_err(&priv->pdev->dev, "OBW count tracking failed"); |
| 930 |
return -EIO; |
| 931 |
} |
| 932 |
|
| 933 |
new_win->active = true; |
| 934 |
new_win->base = win_base; |
| 935 |
new_win->size = size; |
| 936 |
new_win->pbar = pbar; |
| 937 |
priv->obwin_cnt--; |
| 938 |
pbar->free -= size; |
| 939 |
*win_id = new_win_idx; |
| 940 |
return 0; |
| 941 |
} |
| 942 |
|
| 943 |
static int tsi721_map_outb_win(struct rio_mport *mport, u16 destid, u64 rstart, |
| 944 |
u32 size, u32 flags, dma_addr_t *laddr) |
| 945 |
{ |
| 946 |
struct tsi721_device *priv = mport->priv; |
| 947 |
int i; |
| 948 |
struct tsi721_obw_bar *pbar; |
| 949 |
struct tsi721_ob_win *ob_win; |
| 950 |
int obw = -1; |
| 951 |
u32 rval; |
| 952 |
u64 rio_addr; |
| 953 |
u32 zsize; |
| 954 |
int ret = -ENOMEM; |
| 955 |
|
| 956 |
tsi_debug(OBW, &priv->pdev->dev, |
| 957 |
"did=%d ra=0x%llx sz=0x%x", destid, rstart, size); |
| 958 |
|
| 959 |
if (!is_power_of_2(size) || (size < 0x8000) || (rstart & (size - 1))) |
| 960 |
return -EINVAL; |
| 961 |
|
| 962 |
if (priv->obwin_cnt == 0) |
| 963 |
return -EBUSY; |
| 964 |
|
| 965 |
for (i = 0; i < 2; i++) { |
| 966 |
if (priv->p2r_bar[i].free >= size) { |
| 967 |
pbar = &priv->p2r_bar[i]; |
| 968 |
ret = tsi721_obw_alloc(priv, pbar, size, &obw); |
| 969 |
if (!ret) |
| 970 |
break; |
| 971 |
} |
| 972 |
} |
| 973 |
|
| 974 |
if (ret) |
| 975 |
return ret; |
| 976 |
|
| 977 |
WARN_ON(obw == -1); |
| 978 |
ob_win = &priv->ob_win[obw]; |
| 979 |
ob_win->destid = destid; |
| 980 |
ob_win->rstart = rstart; |
| 981 |
tsi_debug(OBW, &priv->pdev->dev, |
| 982 |
"allocated OBW%d @%llx", obw, ob_win->base); |
| 983 |
|
| 984 |
/* |
| 985 |
* Configure Outbound Window |
| 986 |
*/ |
| 987 |
|
| 988 |
zsize = size/TSI721_PC2SR_ZONES; |
| 989 |
rio_addr = rstart; |
| 990 |
|
| 991 |
/* |
| 992 |
* Program Address Translation Zones: |
| 993 |
* This implementation uses all 8 zones associated wit window. |
| 994 |
*/ |
| 995 |
for (i = 0; i < TSI721_PC2SR_ZONES; i++) { |
| 996 |
|
| 997 |
while (ioread32(priv->regs + TSI721_ZONE_SEL) & |
| 998 |
TSI721_ZONE_SEL_GO) { |
| 999 |
udelay(1); |
| 1000 |
} |
| 1001 |
|
| 1002 |
rval = (u32)(rio_addr & TSI721_LUT_DATA0_ADD) | |
| 1003 |
TSI721_LUT_DATA0_NREAD | TSI721_LUT_DATA0_NWR; |
| 1004 |
iowrite32(rval, priv->regs + TSI721_LUT_DATA0); |
| 1005 |
rval = (u32)(rio_addr >> 32); |
| 1006 |
iowrite32(rval, priv->regs + TSI721_LUT_DATA1); |
| 1007 |
rval = destid; |
| 1008 |
iowrite32(rval, priv->regs + TSI721_LUT_DATA2); |
| 1009 |
|
| 1010 |
rval = TSI721_ZONE_SEL_GO | (obw << 3) | i; |
| 1011 |
iowrite32(rval, priv->regs + TSI721_ZONE_SEL); |
| 1012 |
|
| 1013 |
rio_addr += zsize; |
| 1014 |
} |
| 1015 |
|
| 1016 |
iowrite32(TSI721_OBWIN_SIZE(size) << 8, |
| 1017 |
priv->regs + TSI721_OBWINSZ(obw)); |
| 1018 |
iowrite32((u32)(ob_win->base >> 32), priv->regs + TSI721_OBWINUB(obw)); |
| 1019 |
iowrite32((u32)(ob_win->base & TSI721_OBWINLB_BA) | TSI721_OBWINLB_WEN, |
| 1020 |
priv->regs + TSI721_OBWINLB(obw)); |
| 1021 |
|
| 1022 |
*laddr = ob_win->base; |
| 1023 |
return 0; |
| 1024 |
} |
| 1025 |
|
| 1026 |
static void tsi721_unmap_outb_win(struct rio_mport *mport, |
| 1027 |
u16 destid, u64 rstart) |
| 1028 |
{ |
| 1029 |
struct tsi721_device *priv = mport->priv; |
| 1030 |
struct tsi721_ob_win *ob_win; |
| 1031 |
int i; |
| 1032 |
|
| 1033 |
tsi_debug(OBW, &priv->pdev->dev, "did=%d ra=0x%llx", destid, rstart); |
| 1034 |
|
| 1035 |
for (i = 0; i < TSI721_OBWIN_NUM; i++) { |
| 1036 |
ob_win = &priv->ob_win[i]; |
| 1037 |
|
| 1038 |
if (ob_win->active && |
| 1039 |
ob_win->destid == destid && ob_win->rstart == rstart) { |
| 1040 |
tsi_debug(OBW, &priv->pdev->dev, |
| 1041 |
"free OBW%d @%llx", i, ob_win->base); |
| 1042 |
ob_win->active = false; |
| 1043 |
iowrite32(0, priv->regs + TSI721_OBWINLB(i)); |
| 1044 |
ob_win->pbar->free += ob_win->size; |
| 1045 |
priv->obwin_cnt++; |
| 1046 |
break; |
| 1047 |
} |
| 1048 |
} |
| 1049 |
} |
| 1050 |
|
| 1051 |
/** |
| 1052 |
* tsi721_init_pc2sr_mapping - initializes outbound (PCIe->SRIO) |
| 1053 |
* translation regions. |
| 1054 |
* @priv: pointer to tsi721 private data |
| 1055 |
* |
| 1056 |
* Disables SREP translation regions. |
| 1057 |
*/ |
| 1058 |
static void tsi721_init_pc2sr_mapping(struct tsi721_device *priv) |
| 1059 |
{ |
| 1060 |
int i, z; |
| 1061 |
u32 rval; |
| 1062 |
|
| 1063 |
/* Disable all PC2SR translation windows */ |
| 1064 |
for (i = 0; i < TSI721_OBWIN_NUM; i++) |
| 1065 |
iowrite32(0, priv->regs + TSI721_OBWINLB(i)); |
| 1066 |
|
| 1067 |
/* Initialize zone lookup tables to avoid ECC errors on reads */ |
| 1068 |
iowrite32(0, priv->regs + TSI721_LUT_DATA0); |
| 1069 |
iowrite32(0, priv->regs + TSI721_LUT_DATA1); |
| 1070 |
iowrite32(0, priv->regs + TSI721_LUT_DATA2); |
| 1071 |
|
| 1072 |
for (i = 0; i < TSI721_OBWIN_NUM; i++) { |
| 1073 |
for (z = 0; z < TSI721_PC2SR_ZONES; z++) { |
| 1074 |
while (ioread32(priv->regs + TSI721_ZONE_SEL) & |
| 1075 |
TSI721_ZONE_SEL_GO) { |
| 1076 |
udelay(1); |
| 1077 |
} |
| 1078 |
rval = TSI721_ZONE_SEL_GO | (i << 3) | z; |
| 1079 |
iowrite32(rval, priv->regs + TSI721_ZONE_SEL); |
| 1080 |
} |
| 1081 |
} |
| 1082 |
|
| 1083 |
if (priv->p2r_bar[0].size == 0 && priv->p2r_bar[1].size == 0) { |
| 1084 |
priv->obwin_cnt = 0; |
| 1085 |
return; |
| 1086 |
} |
| 1087 |
|
| 1088 |
priv->p2r_bar[0].free = priv->p2r_bar[0].size; |
| 1089 |
priv->p2r_bar[1].free = priv->p2r_bar[1].size; |
| 1090 |
|
| 1091 |
for (i = 0; i < TSI721_OBWIN_NUM; i++) |
| 1092 |
priv->ob_win[i].active = false; |
| 1093 |
|
| 1094 |
priv->obwin_cnt = TSI721_OBWIN_NUM; |
| 1095 |
} |
| 1096 |
|
| 1097 |
/** |
| 1098 |
* tsi721_rio_map_inb_mem -- Mapping inbound memory region. |
| 1099 |
* @mport: RapidIO master port |
| 1100 |
* @lstart: Local memory space start address. |
| 1101 |
* @rstart: RapidIO space start address. |
| 1102 |
* @size: The mapping region size. |
| 1103 |
* @flags: Flags for mapping. 0 for using default flags. |
| 1104 |
* |
| 1105 |
* Return: 0 -- Success. |
| 1106 |
* |
| 1107 |
* This function will create the inbound mapping |
| 1108 |
* from rstart to lstart. |
| 1109 |
*/ |
| 1110 |
static int tsi721_rio_map_inb_mem(struct rio_mport *mport, dma_addr_t lstart, |
| 1111 |
u64 rstart, u64 size, u32 flags) |
| 1112 |
{ |
| 1113 |
struct tsi721_device *priv = mport->priv; |
| 1114 |
int i, avail = -1; |
| 1115 |
u32 regval; |
| 1116 |
struct tsi721_ib_win *ib_win; |
| 1117 |
bool direct = (lstart == rstart); |
| 1118 |
u64 ibw_size; |
| 1119 |
dma_addr_t loc_start; |
| 1120 |
u64 ibw_start; |
| 1121 |
struct tsi721_ib_win_mapping *map = NULL; |
| 1122 |
int ret = -EBUSY; |
| 1123 |
|
| 1124 |
/* Max IBW size supported by HW is 16GB */ |
| 1125 |
if (size > 0x400000000UL) |
| 1126 |
return -EINVAL; |
| 1127 |
|
| 1128 |
if (direct) { |
| 1129 |
/* Calculate minimal acceptable window size and base address */ |
| 1130 |
|
| 1131 |
ibw_size = roundup_pow_of_two(size); |
| 1132 |
ibw_start = lstart & ~(ibw_size - 1); |
| 1133 |
|
| 1134 |
tsi_debug(IBW, &priv->pdev->dev, |
| 1135 |
"Direct (RIO_0x%llx -> PCIe_%pad), size=0x%llx, ibw_start = 0x%llx", |
| 1136 |
rstart, &lstart, size, ibw_start); |
| 1137 |
|
| 1138 |
while ((lstart + size) > (ibw_start + ibw_size)) { |
| 1139 |
ibw_size *= 2; |
| 1140 |
ibw_start = lstart & ~(ibw_size - 1); |
| 1141 |
/* Check for crossing IBW max size 16GB */ |
| 1142 |
if (ibw_size > 0x400000000UL) |
| 1143 |
return -EBUSY; |
| 1144 |
} |
| 1145 |
|
| 1146 |
loc_start = ibw_start; |
| 1147 |
|
| 1148 |
map = kzalloc_obj(struct tsi721_ib_win_mapping, GFP_ATOMIC); |
| 1149 |
if (map == NULL) |
| 1150 |
return -ENOMEM; |
| 1151 |
|
| 1152 |
} else { |
| 1153 |
tsi_debug(IBW, &priv->pdev->dev, |
| 1154 |
"Translated (RIO_0x%llx -> PCIe_%pad), size=0x%llx", |
| 1155 |
rstart, &lstart, size); |
| 1156 |
|
| 1157 |
if (!is_power_of_2(size) || size < 0x1000 || |
| 1158 |
((u64)lstart & (size - 1)) || (rstart & (size - 1))) |
| 1159 |
return -EINVAL; |
| 1160 |
if (priv->ibwin_cnt == 0) |
| 1161 |
return -EBUSY; |
| 1162 |
ibw_start = rstart; |
| 1163 |
ibw_size = size; |
| 1164 |
loc_start = lstart; |
| 1165 |
} |
| 1166 |
|
| 1167 |
/* |
| 1168 |
* Scan for overlapping with active regions and mark the first available |
| 1169 |
* IB window at the same time. |
| 1170 |
*/ |
| 1171 |
for (i = 0; i < TSI721_IBWIN_NUM; i++) { |
| 1172 |
ib_win = &priv->ib_win[i]; |
| 1173 |
|
| 1174 |
if (!ib_win->active) { |
| 1175 |
if (avail == -1) { |
| 1176 |
avail = i; |
| 1177 |
ret = 0; |
| 1178 |
} |
| 1179 |
} else if (ibw_start < (ib_win->rstart + ib_win->size) && |
| 1180 |
(ibw_start + ibw_size) > ib_win->rstart) { |
| 1181 |
/* Return error if address translation involved */ |
| 1182 |
if (!direct || ib_win->xlat) { |
| 1183 |
ret = -EFAULT; |
| 1184 |
break; |
| 1185 |
} |
| 1186 |
|
| 1187 |
/* |
| 1188 |
* Direct mappings usually are larger than originally |
| 1189 |
* requested fragments - check if this new request fits |
| 1190 |
* into it. |
| 1191 |
*/ |
| 1192 |
if (rstart >= ib_win->rstart && |
| 1193 |
(rstart + size) <= (ib_win->rstart + |
| 1194 |
ib_win->size)) { |
| 1195 |
/* We are in - no further mapping required */ |
| 1196 |
map->lstart = lstart; |
| 1197 |
list_add_tail(&map->node, &ib_win->mappings); |
| 1198 |
return 0; |
| 1199 |
} |
| 1200 |
|
| 1201 |
ret = -EFAULT; |
| 1202 |
break; |
| 1203 |
} |
| 1204 |
} |
| 1205 |
|
| 1206 |
if (ret) |
| 1207 |
goto out; |
| 1208 |
i = avail; |
| 1209 |
|
| 1210 |
/* Sanity check: available IB window must be disabled at this point */ |
| 1211 |
regval = ioread32(priv->regs + TSI721_IBWIN_LB(i)); |
| 1212 |
if (WARN_ON(regval & TSI721_IBWIN_LB_WEN)) { |
| 1213 |
ret = -EIO; |
| 1214 |
goto out; |
| 1215 |
} |
| 1216 |
|
| 1217 |
ib_win = &priv->ib_win[i]; |
| 1218 |
ib_win->active = true; |
| 1219 |
ib_win->rstart = ibw_start; |
| 1220 |
ib_win->lstart = loc_start; |
| 1221 |
ib_win->size = ibw_size; |
| 1222 |
ib_win->xlat = (lstart != rstart); |
| 1223 |
INIT_LIST_HEAD(&ib_win->mappings); |
| 1224 |
|
| 1225 |
/* |
| 1226 |
* When using direct IBW mapping and have larger than requested IBW size |
| 1227 |
* we can have multiple local memory blocks mapped through the same IBW |
| 1228 |
* To handle this situation we maintain list of "clients" for such IBWs. |
| 1229 |
*/ |
| 1230 |
if (direct) { |
| 1231 |
map->lstart = lstart; |
| 1232 |
list_add_tail(&map->node, &ib_win->mappings); |
| 1233 |
} |
| 1234 |
|
| 1235 |
iowrite32(TSI721_IBWIN_SIZE(ibw_size) << 8, |
| 1236 |
priv->regs + TSI721_IBWIN_SZ(i)); |
| 1237 |
|
| 1238 |
iowrite32(((u64)loc_start >> 32), priv->regs + TSI721_IBWIN_TUA(i)); |
| 1239 |
iowrite32(((u64)loc_start & TSI721_IBWIN_TLA_ADD), |
| 1240 |
priv->regs + TSI721_IBWIN_TLA(i)); |
| 1241 |
|
| 1242 |
iowrite32(ibw_start >> 32, priv->regs + TSI721_IBWIN_UB(i)); |
| 1243 |
iowrite32((ibw_start & TSI721_IBWIN_LB_BA) | TSI721_IBWIN_LB_WEN, |
| 1244 |
priv->regs + TSI721_IBWIN_LB(i)); |
| 1245 |
|
| 1246 |
priv->ibwin_cnt--; |
| 1247 |
|
| 1248 |
tsi_debug(IBW, &priv->pdev->dev, |
| 1249 |
"Configured IBWIN%d (RIO_0x%llx -> PCIe_%pad), size=0x%llx", |
| 1250 |
i, ibw_start, &loc_start, ibw_size); |
| 1251 |
|
| 1252 |
return 0; |
| 1253 |
out: |
| 1254 |
kfree(map); |
| 1255 |
return ret; |
| 1256 |
} |
| 1257 |
|
| 1258 |
/** |
| 1259 |
* tsi721_rio_unmap_inb_mem -- Unmapping inbound memory region. |
| 1260 |
* @mport: RapidIO master port |
| 1261 |
* @lstart: Local memory space start address. |
| 1262 |
*/ |
| 1263 |
static void tsi721_rio_unmap_inb_mem(struct rio_mport *mport, |
| 1264 |
dma_addr_t lstart) |
| 1265 |
{ |
| 1266 |
struct tsi721_device *priv = mport->priv; |
| 1267 |
struct tsi721_ib_win *ib_win; |
| 1268 |
int i; |
| 1269 |
|
| 1270 |
tsi_debug(IBW, &priv->pdev->dev, |
| 1271 |
"Unmap IBW mapped to PCIe_%pad", &lstart); |
| 1272 |
|
| 1273 |
/* Search for matching active inbound translation window */ |
| 1274 |
for (i = 0; i < TSI721_IBWIN_NUM; i++) { |
| 1275 |
ib_win = &priv->ib_win[i]; |
| 1276 |
|
| 1277 |
/* Address translating IBWs must to be an exact march */ |
| 1278 |
if (!ib_win->active || |
| 1279 |
(ib_win->xlat && lstart != ib_win->lstart)) |
| 1280 |
continue; |
| 1281 |
|
| 1282 |
if (lstart >= ib_win->lstart && |
| 1283 |
lstart < (ib_win->lstart + ib_win->size)) { |
| 1284 |
|
| 1285 |
if (!ib_win->xlat) { |
| 1286 |
struct tsi721_ib_win_mapping *map; |
| 1287 |
int found = 0; |
| 1288 |
|
| 1289 |
list_for_each_entry(map, |
| 1290 |
&ib_win->mappings, node) { |
| 1291 |
if (map->lstart == lstart) { |
| 1292 |
list_del(&map->node); |
| 1293 |
kfree(map); |
| 1294 |
found = 1; |
| 1295 |
break; |
| 1296 |
} |
| 1297 |
} |
| 1298 |
|
| 1299 |
if (!found) |
| 1300 |
continue; |
| 1301 |
|
| 1302 |
if (!list_empty(&ib_win->mappings)) |
| 1303 |
break; |
| 1304 |
} |
| 1305 |
|
| 1306 |
tsi_debug(IBW, &priv->pdev->dev, "Disable IBWIN_%d", i); |
| 1307 |
iowrite32(0, priv->regs + TSI721_IBWIN_LB(i)); |
| 1308 |
ib_win->active = false; |
| 1309 |
priv->ibwin_cnt++; |
| 1310 |
break; |
| 1311 |
} |
| 1312 |
} |
| 1313 |
|
| 1314 |
if (i == TSI721_IBWIN_NUM) |
| 1315 |
tsi_debug(IBW, &priv->pdev->dev, |
| 1316 |
"IB window mapped to %pad not found", &lstart); |
| 1317 |
} |
| 1318 |
|
| 1319 |
/** |
| 1320 |
* tsi721_init_sr2pc_mapping - initializes inbound (SRIO->PCIe) |
| 1321 |
* translation regions. |
| 1322 |
* @priv: pointer to tsi721 private data |
| 1323 |
* |
| 1324 |
* Disables inbound windows. |
| 1325 |
*/ |
| 1326 |
static void tsi721_init_sr2pc_mapping(struct tsi721_device *priv) |
| 1327 |
{ |
| 1328 |
int i; |
| 1329 |
|
| 1330 |
/* Disable all SR2PC inbound windows */ |
| 1331 |
for (i = 0; i < TSI721_IBWIN_NUM; i++) |
| 1332 |
iowrite32(0, priv->regs + TSI721_IBWIN_LB(i)); |
| 1333 |
priv->ibwin_cnt = TSI721_IBWIN_NUM; |
| 1334 |
} |
| 1335 |
|
| 1336 |
/* |
| 1337 |
* tsi721_close_sr2pc_mapping - closes all active inbound (SRIO->PCIe) |
| 1338 |
* translation regions. |
| 1339 |
* @priv: pointer to tsi721 device private data |
| 1340 |
*/ |
| 1341 |
static void tsi721_close_sr2pc_mapping(struct tsi721_device *priv) |
| 1342 |
{ |
| 1343 |
struct tsi721_ib_win *ib_win; |
| 1344 |
int i; |
| 1345 |
|
| 1346 |
/* Disable all active SR2PC inbound windows */ |
| 1347 |
for (i = 0; i < TSI721_IBWIN_NUM; i++) { |
| 1348 |
ib_win = &priv->ib_win[i]; |
| 1349 |
if (ib_win->active) { |
| 1350 |
iowrite32(0, priv->regs + TSI721_IBWIN_LB(i)); |
| 1351 |
ib_win->active = false; |
| 1352 |
} |
| 1353 |
} |
| 1354 |
} |
| 1355 |
|
| 1356 |
/** |
| 1357 |
* tsi721_port_write_init - Inbound port write interface init |
| 1358 |
* @priv: pointer to tsi721 private data |
| 1359 |
* |
| 1360 |
* Initializes inbound port write handler. |
| 1361 |
* Returns: %0 on success or %-ENOMEM on failure. |
| 1362 |
*/ |
| 1363 |
static int tsi721_port_write_init(struct tsi721_device *priv) |
| 1364 |
{ |
| 1365 |
priv->pw_discard_count = 0; |
| 1366 |
INIT_WORK(&priv->pw_work, tsi721_pw_dpc); |
| 1367 |
spin_lock_init(&priv->pw_fifo_lock); |
| 1368 |
if (kfifo_alloc(&priv->pw_fifo, |
| 1369 |
TSI721_RIO_PW_MSG_SIZE * 32, GFP_KERNEL)) { |
| 1370 |
tsi_err(&priv->pdev->dev, "PW FIFO allocation failed"); |
| 1371 |
return -ENOMEM; |
| 1372 |
} |
| 1373 |
|
| 1374 |
/* Use reliable port-write capture mode */ |
| 1375 |
iowrite32(TSI721_RIO_PW_CTL_PWC_REL, priv->regs + TSI721_RIO_PW_CTL); |
| 1376 |
return 0; |
| 1377 |
} |
| 1378 |
|
| 1379 |
static void tsi721_port_write_free(struct tsi721_device *priv) |
| 1380 |
{ |
| 1381 |
kfifo_free(&priv->pw_fifo); |
| 1382 |
} |
| 1383 |
|
| 1384 |
static int tsi721_doorbell_init(struct tsi721_device *priv) |
| 1385 |
{ |
| 1386 |
/* Outbound Doorbells do not require any setup. |
| 1387 |
* Tsi721 uses dedicated PCI BAR1 to generate doorbells. |
| 1388 |
* That BAR1 was mapped during the probe routine. |
| 1389 |
*/ |
| 1390 |
|
| 1391 |
/* Initialize Inbound Doorbell processing DPC and queue */ |
| 1392 |
priv->db_discard_count = 0; |
| 1393 |
INIT_WORK(&priv->idb_work, tsi721_db_dpc); |
| 1394 |
|
| 1395 |
/* Allocate buffer for inbound doorbells queue */ |
| 1396 |
priv->idb_base = dma_alloc_coherent(&priv->pdev->dev, |
| 1397 |
IDB_QSIZE * TSI721_IDB_ENTRY_SIZE, |
| 1398 |
&priv->idb_dma, GFP_KERNEL); |
| 1399 |
if (!priv->idb_base) |
| 1400 |
return -ENOMEM; |
| 1401 |
|
| 1402 |
tsi_debug(DBELL, &priv->pdev->dev, |
| 1403 |
"Allocated IDB buffer @ %p (phys = %pad)", |
| 1404 |
priv->idb_base, &priv->idb_dma); |
| 1405 |
|
| 1406 |
iowrite32(TSI721_IDQ_SIZE_VAL(IDB_QSIZE), |
| 1407 |
priv->regs + TSI721_IDQ_SIZE(IDB_QUEUE)); |
| 1408 |
iowrite32(((u64)priv->idb_dma >> 32), |
| 1409 |
priv->regs + TSI721_IDQ_BASEU(IDB_QUEUE)); |
| 1410 |
iowrite32(((u64)priv->idb_dma & TSI721_IDQ_BASEL_ADDR), |
| 1411 |
priv->regs + TSI721_IDQ_BASEL(IDB_QUEUE)); |
| 1412 |
/* Enable accepting all inbound doorbells */ |
| 1413 |
iowrite32(0, priv->regs + TSI721_IDQ_MASK(IDB_QUEUE)); |
| 1414 |
|
| 1415 |
iowrite32(TSI721_IDQ_INIT, priv->regs + TSI721_IDQ_CTL(IDB_QUEUE)); |
| 1416 |
|
| 1417 |
iowrite32(0, priv->regs + TSI721_IDQ_RP(IDB_QUEUE)); |
| 1418 |
|
| 1419 |
return 0; |
| 1420 |
} |
| 1421 |
|
| 1422 |
static void tsi721_doorbell_free(struct tsi721_device *priv) |
| 1423 |
{ |
| 1424 |
if (priv->idb_base == NULL) |
| 1425 |
return; |
| 1426 |
|
| 1427 |
/* Free buffer allocated for inbound doorbell queue */ |
| 1428 |
dma_free_coherent(&priv->pdev->dev, IDB_QSIZE * TSI721_IDB_ENTRY_SIZE, |
| 1429 |
priv->idb_base, priv->idb_dma); |
| 1430 |
priv->idb_base = NULL; |
| 1431 |
} |
| 1432 |
|
| 1433 |
/** |
| 1434 |
* tsi721_bdma_maint_init - Initialize maintenance request BDMA channel. |
| 1435 |
* @priv: pointer to tsi721 private data |
| 1436 |
* |
| 1437 |
* Initialize BDMA channel allocated for RapidIO maintenance read/write |
| 1438 |
* request generation |
| 1439 |
* |
| 1440 |
* Returns: %0 on success or %-ENOMEM on failure. |
| 1441 |
*/ |
| 1442 |
static int tsi721_bdma_maint_init(struct tsi721_device *priv) |
| 1443 |
{ |
| 1444 |
struct tsi721_dma_desc *bd_ptr; |
| 1445 |
u64 *sts_ptr; |
| 1446 |
dma_addr_t bd_phys, sts_phys; |
| 1447 |
int sts_size; |
| 1448 |
int bd_num = 2; |
| 1449 |
void __iomem *regs; |
| 1450 |
|
| 1451 |
tsi_debug(MAINT, &priv->pdev->dev, |
| 1452 |
"Init BDMA_%d Maintenance requests", TSI721_DMACH_MAINT); |
| 1453 |
|
| 1454 |
/* |
| 1455 |
* Initialize DMA channel for maintenance requests |
| 1456 |
*/ |
| 1457 |
|
| 1458 |
priv->mdma.ch_id = TSI721_DMACH_MAINT; |
| 1459 |
regs = priv->regs + TSI721_DMAC_BASE(TSI721_DMACH_MAINT); |
| 1460 |
|
| 1461 |
/* Allocate space for DMA descriptors */ |
| 1462 |
bd_ptr = dma_alloc_coherent(&priv->pdev->dev, |
| 1463 |
bd_num * sizeof(struct tsi721_dma_desc), |
| 1464 |
&bd_phys, GFP_KERNEL); |
| 1465 |
if (!bd_ptr) |
| 1466 |
return -ENOMEM; |
| 1467 |
|
| 1468 |
priv->mdma.bd_num = bd_num; |
| 1469 |
priv->mdma.bd_phys = bd_phys; |
| 1470 |
priv->mdma.bd_base = bd_ptr; |
| 1471 |
|
| 1472 |
tsi_debug(MAINT, &priv->pdev->dev, "DMA descriptors @ %p (phys = %pad)", |
| 1473 |
bd_ptr, &bd_phys); |
| 1474 |
|
| 1475 |
/* Allocate space for descriptor status FIFO */ |
| 1476 |
sts_size = (bd_num >= TSI721_DMA_MINSTSSZ) ? |
| 1477 |
bd_num : TSI721_DMA_MINSTSSZ; |
| 1478 |
sts_size = roundup_pow_of_two(sts_size); |
| 1479 |
sts_ptr = dma_alloc_coherent(&priv->pdev->dev, |
| 1480 |
sts_size * sizeof(struct tsi721_dma_sts), |
| 1481 |
&sts_phys, GFP_KERNEL); |
| 1482 |
if (!sts_ptr) { |
| 1483 |
/* Free space allocated for DMA descriptors */ |
| 1484 |
dma_free_coherent(&priv->pdev->dev, |
| 1485 |
bd_num * sizeof(struct tsi721_dma_desc), |
| 1486 |
bd_ptr, bd_phys); |
| 1487 |
priv->mdma.bd_base = NULL; |
| 1488 |
return -ENOMEM; |
| 1489 |
} |
| 1490 |
|
| 1491 |
priv->mdma.sts_phys = sts_phys; |
| 1492 |
priv->mdma.sts_base = sts_ptr; |
| 1493 |
priv->mdma.sts_size = sts_size; |
| 1494 |
|
| 1495 |
tsi_debug(MAINT, &priv->pdev->dev, |
| 1496 |
"desc status FIFO @ %p (phys = %pad) size=0x%x", |
| 1497 |
sts_ptr, &sts_phys, sts_size); |
| 1498 |
|
| 1499 |
/* Initialize DMA descriptors ring */ |
| 1500 |
bd_ptr[bd_num - 1].type_id = cpu_to_le32(DTYPE3 << 29); |
| 1501 |
bd_ptr[bd_num - 1].next_lo = cpu_to_le32((u64)bd_phys & |
| 1502 |
TSI721_DMAC_DPTRL_MASK); |
| 1503 |
bd_ptr[bd_num - 1].next_hi = cpu_to_le32((u64)bd_phys >> 32); |
| 1504 |
|
| 1505 |
/* Setup DMA descriptor pointers */ |
| 1506 |
iowrite32(((u64)bd_phys >> 32), regs + TSI721_DMAC_DPTRH); |
| 1507 |
iowrite32(((u64)bd_phys & TSI721_DMAC_DPTRL_MASK), |
| 1508 |
regs + TSI721_DMAC_DPTRL); |
| 1509 |
|
| 1510 |
/* Setup descriptor status FIFO */ |
| 1511 |
iowrite32(((u64)sts_phys >> 32), regs + TSI721_DMAC_DSBH); |
| 1512 |
iowrite32(((u64)sts_phys & TSI721_DMAC_DSBL_MASK), |
| 1513 |
regs + TSI721_DMAC_DSBL); |
| 1514 |
iowrite32(TSI721_DMAC_DSSZ_SIZE(sts_size), |
| 1515 |
regs + TSI721_DMAC_DSSZ); |
| 1516 |
|
| 1517 |
/* Clear interrupt bits */ |
| 1518 |
iowrite32(TSI721_DMAC_INT_ALL, regs + TSI721_DMAC_INT); |
| 1519 |
|
| 1520 |
ioread32(regs + TSI721_DMAC_INT); |
| 1521 |
|
| 1522 |
/* Toggle DMA channel initialization */ |
| 1523 |
iowrite32(TSI721_DMAC_CTL_INIT, regs + TSI721_DMAC_CTL); |
| 1524 |
ioread32(regs + TSI721_DMAC_CTL); |
| 1525 |
udelay(10); |
| 1526 |
|
| 1527 |
return 0; |
| 1528 |
} |
| 1529 |
|
| 1530 |
static int tsi721_bdma_maint_free(struct tsi721_device *priv) |
| 1531 |
{ |
| 1532 |
u32 ch_stat; |
| 1533 |
struct tsi721_bdma_maint *mdma = &priv->mdma; |
| 1534 |
void __iomem *regs = priv->regs + TSI721_DMAC_BASE(mdma->ch_id); |
| 1535 |
|
| 1536 |
if (mdma->bd_base == NULL) |
| 1537 |
return 0; |
| 1538 |
|
| 1539 |
/* Check if DMA channel still running */ |
| 1540 |
ch_stat = ioread32(regs + TSI721_DMAC_STS); |
| 1541 |
if (ch_stat & TSI721_DMAC_STS_RUN) |
| 1542 |
return -EFAULT; |
| 1543 |
|
| 1544 |
/* Put DMA channel into init state */ |
| 1545 |
iowrite32(TSI721_DMAC_CTL_INIT, regs + TSI721_DMAC_CTL); |
| 1546 |
|
| 1547 |
/* Free space allocated for DMA descriptors */ |
| 1548 |
dma_free_coherent(&priv->pdev->dev, |
| 1549 |
mdma->bd_num * sizeof(struct tsi721_dma_desc), |
| 1550 |
mdma->bd_base, mdma->bd_phys); |
| 1551 |
mdma->bd_base = NULL; |
| 1552 |
|
| 1553 |
/* Free space allocated for status FIFO */ |
| 1554 |
dma_free_coherent(&priv->pdev->dev, |
| 1555 |
mdma->sts_size * sizeof(struct tsi721_dma_sts), |
| 1556 |
mdma->sts_base, mdma->sts_phys); |
| 1557 |
mdma->sts_base = NULL; |
| 1558 |
return 0; |
| 1559 |
} |
| 1560 |
|
| 1561 |
/* Enable Inbound Messaging Interrupts */ |
| 1562 |
static void |
| 1563 |
tsi721_imsg_interrupt_enable(struct tsi721_device *priv, int ch, |
| 1564 |
u32 inte_mask) |
| 1565 |
{ |
| 1566 |
u32 rval; |
| 1567 |
|
| 1568 |
if (!inte_mask) |
| 1569 |
return; |
| 1570 |
|
| 1571 |
/* Clear pending Inbound Messaging interrupts */ |
| 1572 |
iowrite32(inte_mask, priv->regs + TSI721_IBDMAC_INT(ch)); |
| 1573 |
|
| 1574 |
/* Enable Inbound Messaging interrupts */ |
| 1575 |
rval = ioread32(priv->regs + TSI721_IBDMAC_INTE(ch)); |
| 1576 |
iowrite32(rval | inte_mask, priv->regs + TSI721_IBDMAC_INTE(ch)); |
| 1577 |
|
| 1578 |
if (priv->flags & TSI721_USING_MSIX) |
| 1579 |
return; /* Finished if we are in MSI-X mode */ |
| 1580 |
|
| 1581 |
/* |
| 1582 |
* For MSI and INTA interrupt signalling we need to enable next levels |
| 1583 |
*/ |
| 1584 |
|
| 1585 |
/* Enable Device Channel Interrupt */ |
| 1586 |
rval = ioread32(priv->regs + TSI721_DEV_CHAN_INTE); |
| 1587 |
iowrite32(rval | TSI721_INT_IMSG_CHAN(ch), |
| 1588 |
priv->regs + TSI721_DEV_CHAN_INTE); |
| 1589 |
} |
| 1590 |
|
| 1591 |
/* Disable Inbound Messaging Interrupts */ |
| 1592 |
static void |
| 1593 |
tsi721_imsg_interrupt_disable(struct tsi721_device *priv, int ch, |
| 1594 |
u32 inte_mask) |
| 1595 |
{ |
| 1596 |
u32 rval; |
| 1597 |
|
| 1598 |
if (!inte_mask) |
| 1599 |
return; |
| 1600 |
|
| 1601 |
/* Clear pending Inbound Messaging interrupts */ |
| 1602 |
iowrite32(inte_mask, priv->regs + TSI721_IBDMAC_INT(ch)); |
| 1603 |
|
| 1604 |
/* Disable Inbound Messaging interrupts */ |
| 1605 |
rval = ioread32(priv->regs + TSI721_IBDMAC_INTE(ch)); |
| 1606 |
rval &= ~inte_mask; |
| 1607 |
iowrite32(rval, priv->regs + TSI721_IBDMAC_INTE(ch)); |
| 1608 |
|
| 1609 |
if (priv->flags & TSI721_USING_MSIX) |
| 1610 |
return; /* Finished if we are in MSI-X mode */ |
| 1611 |
|
| 1612 |
/* |
| 1613 |
* For MSI and INTA interrupt signalling we need to disable next levels |
| 1614 |
*/ |
| 1615 |
|
| 1616 |
/* Disable Device Channel Interrupt */ |
| 1617 |
rval = ioread32(priv->regs + TSI721_DEV_CHAN_INTE); |
| 1618 |
rval &= ~TSI721_INT_IMSG_CHAN(ch); |
| 1619 |
iowrite32(rval, priv->regs + TSI721_DEV_CHAN_INTE); |
| 1620 |
} |
| 1621 |
|
| 1622 |
/* Enable Outbound Messaging interrupts */ |
| 1623 |
static void |
| 1624 |
tsi721_omsg_interrupt_enable(struct tsi721_device *priv, int ch, |
| 1625 |
u32 inte_mask) |
| 1626 |
{ |
| 1627 |
u32 rval; |
| 1628 |
|
| 1629 |
if (!inte_mask) |
| 1630 |
return; |
| 1631 |
|
| 1632 |
/* Clear pending Outbound Messaging interrupts */ |
| 1633 |
iowrite32(inte_mask, priv->regs + TSI721_OBDMAC_INT(ch)); |
| 1634 |
|
| 1635 |
/* Enable Outbound Messaging channel interrupts */ |
| 1636 |
rval = ioread32(priv->regs + TSI721_OBDMAC_INTE(ch)); |
| 1637 |
iowrite32(rval | inte_mask, priv->regs + TSI721_OBDMAC_INTE(ch)); |
| 1638 |
|
| 1639 |
if (priv->flags & TSI721_USING_MSIX) |
| 1640 |
return; /* Finished if we are in MSI-X mode */ |
| 1641 |
|
| 1642 |
/* |
| 1643 |
* For MSI and INTA interrupt signalling we need to enable next levels |
| 1644 |
*/ |
| 1645 |
|
| 1646 |
/* Enable Device Channel Interrupt */ |
| 1647 |
rval = ioread32(priv->regs + TSI721_DEV_CHAN_INTE); |
| 1648 |
iowrite32(rval | TSI721_INT_OMSG_CHAN(ch), |
| 1649 |
priv->regs + TSI721_DEV_CHAN_INTE); |
| 1650 |
} |
| 1651 |
|
| 1652 |
/* Disable Outbound Messaging interrupts */ |
| 1653 |
static void |
| 1654 |
tsi721_omsg_interrupt_disable(struct tsi721_device *priv, int ch, |
| 1655 |
u32 inte_mask) |
| 1656 |
{ |
| 1657 |
u32 rval; |
| 1658 |
|
| 1659 |
if (!inte_mask) |
| 1660 |
return; |
| 1661 |
|
| 1662 |
/* Clear pending Outbound Messaging interrupts */ |
| 1663 |
iowrite32(inte_mask, priv->regs + TSI721_OBDMAC_INT(ch)); |
| 1664 |
|
| 1665 |
/* Disable Outbound Messaging interrupts */ |
| 1666 |
rval = ioread32(priv->regs + TSI721_OBDMAC_INTE(ch)); |
| 1667 |
rval &= ~inte_mask; |
| 1668 |
iowrite32(rval, priv->regs + TSI721_OBDMAC_INTE(ch)); |
| 1669 |
|
| 1670 |
if (priv->flags & TSI721_USING_MSIX) |
| 1671 |
return; /* Finished if we are in MSI-X mode */ |
| 1672 |
|
| 1673 |
/* |
| 1674 |
* For MSI and INTA interrupt signalling we need to disable next levels |
| 1675 |
*/ |
| 1676 |
|
| 1677 |
/* Disable Device Channel Interrupt */ |
| 1678 |
rval = ioread32(priv->regs + TSI721_DEV_CHAN_INTE); |
| 1679 |
rval &= ~TSI721_INT_OMSG_CHAN(ch); |
| 1680 |
iowrite32(rval, priv->regs + TSI721_DEV_CHAN_INTE); |
| 1681 |
} |
| 1682 |
|
| 1683 |
/** |
| 1684 |
* tsi721_add_outb_message - Add message to the Tsi721 outbound message queue |
| 1685 |
* @mport: Master port with outbound message queue |
| 1686 |
* @rdev: Target of outbound message |
| 1687 |
* @mbox: Outbound mailbox |
| 1688 |
* @buffer: Message to add to outbound queue |
| 1689 |
* @len: Length of message |
| 1690 |
* |
| 1691 |
* Returns: %0 on success or -errno value on failure. |
| 1692 |
*/ |
| 1693 |
static int |
| 1694 |
tsi721_add_outb_message(struct rio_mport *mport, struct rio_dev *rdev, int mbox, |
| 1695 |
void *buffer, size_t len) |
| 1696 |
{ |
| 1697 |
struct tsi721_device *priv = mport->priv; |
| 1698 |
struct tsi721_omsg_desc *desc; |
| 1699 |
u32 tx_slot; |
| 1700 |
unsigned long flags; |
| 1701 |
|
| 1702 |
if (!priv->omsg_init[mbox] || |
| 1703 |
len > TSI721_MSG_MAX_SIZE || len < 8) |
| 1704 |
return -EINVAL; |
| 1705 |
|
| 1706 |
spin_lock_irqsave(&priv->omsg_ring[mbox].lock, flags); |
| 1707 |
|
| 1708 |
tx_slot = priv->omsg_ring[mbox].tx_slot; |
| 1709 |
|
| 1710 |
/* Copy copy message into transfer buffer */ |
| 1711 |
memcpy(priv->omsg_ring[mbox].omq_base[tx_slot], buffer, len); |
| 1712 |
|
| 1713 |
if (len & 0x7) |
| 1714 |
len += 8; |
| 1715 |
|
| 1716 |
/* Build descriptor associated with buffer */ |
| 1717 |
desc = priv->omsg_ring[mbox].omd_base; |
| 1718 |
desc[tx_slot].type_id = cpu_to_le32((DTYPE4 << 29) | rdev->destid); |
| 1719 |
#ifdef TSI721_OMSG_DESC_INT |
| 1720 |
/* Request IOF_DONE interrupt generation for each N-th frame in queue */ |
| 1721 |
if (tx_slot % 4 == 0) |
| 1722 |
desc[tx_slot].type_id |= cpu_to_le32(TSI721_OMD_IOF); |
| 1723 |
#endif |
| 1724 |
desc[tx_slot].msg_info = |
| 1725 |
cpu_to_le32((mport->sys_size << 26) | (mbox << 22) | |
| 1726 |
(0xe << 12) | (len & 0xff8)); |
| 1727 |
desc[tx_slot].bufptr_lo = |
| 1728 |
cpu_to_le32((u64)priv->omsg_ring[mbox].omq_phys[tx_slot] & |
| 1729 |
0xffffffff); |
| 1730 |
desc[tx_slot].bufptr_hi = |
| 1731 |
cpu_to_le32((u64)priv->omsg_ring[mbox].omq_phys[tx_slot] >> 32); |
| 1732 |
|
| 1733 |
priv->omsg_ring[mbox].wr_count++; |
| 1734 |
|
| 1735 |
/* Go to next descriptor */ |
| 1736 |
if (++priv->omsg_ring[mbox].tx_slot == priv->omsg_ring[mbox].size) { |
| 1737 |
priv->omsg_ring[mbox].tx_slot = 0; |
| 1738 |
/* Move through the ring link descriptor at the end */ |
| 1739 |
priv->omsg_ring[mbox].wr_count++; |
| 1740 |
} |
| 1741 |
|
| 1742 |
mb(); |
| 1743 |
|
| 1744 |
/* Set new write count value */ |
| 1745 |
iowrite32(priv->omsg_ring[mbox].wr_count, |
| 1746 |
priv->regs + TSI721_OBDMAC_DWRCNT(mbox)); |
| 1747 |
ioread32(priv->regs + TSI721_OBDMAC_DWRCNT(mbox)); |
| 1748 |
|
| 1749 |
spin_unlock_irqrestore(&priv->omsg_ring[mbox].lock, flags); |
| 1750 |
|
| 1751 |
return 0; |
| 1752 |
} |
| 1753 |
|
| 1754 |
/** |
| 1755 |
* tsi721_omsg_handler - Outbound Message Interrupt Handler |
| 1756 |
* @priv: pointer to tsi721 private data |
| 1757 |
* @ch: number of OB MSG channel to service |
| 1758 |
* |
| 1759 |
* Services channel interrupts from outbound messaging engine. |
| 1760 |
*/ |
| 1761 |
static void tsi721_omsg_handler(struct tsi721_device *priv, int ch) |
| 1762 |
{ |
| 1763 |
u32 omsg_int; |
| 1764 |
struct rio_mport *mport = &priv->mport; |
| 1765 |
void *dev_id = NULL; |
| 1766 |
u32 tx_slot = 0xffffffff; |
| 1767 |
int do_callback = 0; |
| 1768 |
|
| 1769 |
spin_lock(&priv->omsg_ring[ch].lock); |
| 1770 |
|
| 1771 |
omsg_int = ioread32(priv->regs + TSI721_OBDMAC_INT(ch)); |
| 1772 |
|
| 1773 |
if (omsg_int & TSI721_OBDMAC_INT_ST_FULL) |
| 1774 |
tsi_info(&priv->pdev->dev, |
| 1775 |
"OB MBOX%d: Status FIFO is full", ch); |
| 1776 |
|
| 1777 |
if (omsg_int & (TSI721_OBDMAC_INT_DONE | TSI721_OBDMAC_INT_IOF_DONE)) { |
| 1778 |
u32 srd_ptr; |
| 1779 |
u64 *sts_ptr, last_ptr = 0, prev_ptr = 0; |
| 1780 |
int i, j; |
| 1781 |
|
| 1782 |
/* |
| 1783 |
* Find last successfully processed descriptor |
| 1784 |
*/ |
| 1785 |
|
| 1786 |
/* Check and clear descriptor status FIFO entries */ |
| 1787 |
srd_ptr = priv->omsg_ring[ch].sts_rdptr; |
| 1788 |
sts_ptr = priv->omsg_ring[ch].sts_base; |
| 1789 |
j = srd_ptr * 8; |
| 1790 |
while (sts_ptr[j]) { |
| 1791 |
for (i = 0; i < 8 && sts_ptr[j]; i++, j++) { |
| 1792 |
prev_ptr = last_ptr; |
| 1793 |
last_ptr = le64_to_cpu(sts_ptr[j]); |
| 1794 |
sts_ptr[j] = 0; |
| 1795 |
} |
| 1796 |
|
| 1797 |
++srd_ptr; |
| 1798 |
srd_ptr %= priv->omsg_ring[ch].sts_size; |
| 1799 |
j = srd_ptr * 8; |
| 1800 |
} |
| 1801 |
|
| 1802 |
if (last_ptr == 0) |
| 1803 |
goto no_sts_update; |
| 1804 |
|
| 1805 |
priv->omsg_ring[ch].sts_rdptr = srd_ptr; |
| 1806 |
iowrite32(srd_ptr, priv->regs + TSI721_OBDMAC_DSRP(ch)); |
| 1807 |
|
| 1808 |
if (!mport->outb_msg[ch].mcback) |
| 1809 |
goto no_sts_update; |
| 1810 |
|
| 1811 |
/* Inform upper layer about transfer completion */ |
| 1812 |
|
| 1813 |
tx_slot = (last_ptr - (u64)priv->omsg_ring[ch].omd_phys)/ |
| 1814 |
sizeof(struct tsi721_omsg_desc); |
| 1815 |
|
| 1816 |
/* |
| 1817 |
* Check if this is a Link Descriptor (LD). |
| 1818 |
* If yes, ignore LD and use descriptor processed |
| 1819 |
* before LD. |
| 1820 |
*/ |
| 1821 |
if (tx_slot == priv->omsg_ring[ch].size) { |
| 1822 |
if (prev_ptr) |
| 1823 |
tx_slot = (prev_ptr - |
| 1824 |
(u64)priv->omsg_ring[ch].omd_phys)/ |
| 1825 |
sizeof(struct tsi721_omsg_desc); |
| 1826 |
else |
| 1827 |
goto no_sts_update; |
| 1828 |
} |
| 1829 |
|
| 1830 |
if (tx_slot >= priv->omsg_ring[ch].size) |
| 1831 |
tsi_debug(OMSG, &priv->pdev->dev, |
| 1832 |
"OB_MSG tx_slot=%x > size=%x", |
| 1833 |
tx_slot, priv->omsg_ring[ch].size); |
| 1834 |
WARN_ON(tx_slot >= priv->omsg_ring[ch].size); |
| 1835 |
|
| 1836 |
/* Move slot index to the next message to be sent */ |
| 1837 |
++tx_slot; |
| 1838 |
if (tx_slot == priv->omsg_ring[ch].size) |
| 1839 |
tx_slot = 0; |
| 1840 |
|
| 1841 |
dev_id = priv->omsg_ring[ch].dev_id; |
| 1842 |
do_callback = 1; |
| 1843 |
} |
| 1844 |
|
| 1845 |
no_sts_update: |
| 1846 |
|
| 1847 |
if (omsg_int & TSI721_OBDMAC_INT_ERROR) { |
| 1848 |
/* |
| 1849 |
* Outbound message operation aborted due to error, |
| 1850 |
* reinitialize OB MSG channel |
| 1851 |
*/ |
| 1852 |
|
| 1853 |
tsi_debug(OMSG, &priv->pdev->dev, "OB MSG ABORT ch_stat=%x", |
| 1854 |
ioread32(priv->regs + TSI721_OBDMAC_STS(ch))); |
| 1855 |
|
| 1856 |
iowrite32(TSI721_OBDMAC_INT_ERROR, |
| 1857 |
priv->regs + TSI721_OBDMAC_INT(ch)); |
| 1858 |
iowrite32(TSI721_OBDMAC_CTL_RETRY_THR | TSI721_OBDMAC_CTL_INIT, |
| 1859 |
priv->regs + TSI721_OBDMAC_CTL(ch)); |
| 1860 |
ioread32(priv->regs + TSI721_OBDMAC_CTL(ch)); |
| 1861 |
|
| 1862 |
/* Inform upper level to clear all pending tx slots */ |
| 1863 |
dev_id = priv->omsg_ring[ch].dev_id; |
| 1864 |
tx_slot = priv->omsg_ring[ch].tx_slot; |
| 1865 |
do_callback = 1; |
| 1866 |
|
| 1867 |
/* Synch tx_slot tracking */ |
| 1868 |
iowrite32(priv->omsg_ring[ch].tx_slot, |
| 1869 |
priv->regs + TSI721_OBDMAC_DRDCNT(ch)); |
| 1870 |
ioread32(priv->regs + TSI721_OBDMAC_DRDCNT(ch)); |
| 1871 |
priv->omsg_ring[ch].wr_count = priv->omsg_ring[ch].tx_slot; |
| 1872 |
priv->omsg_ring[ch].sts_rdptr = 0; |
| 1873 |
} |
| 1874 |
|
| 1875 |
/* Clear channel interrupts */ |
| 1876 |
iowrite32(omsg_int, priv->regs + TSI721_OBDMAC_INT(ch)); |
| 1877 |
|
| 1878 |
if (!(priv->flags & TSI721_USING_MSIX)) { |
| 1879 |
u32 ch_inte; |
| 1880 |
|
| 1881 |
/* Re-enable channel interrupts */ |
| 1882 |
ch_inte = ioread32(priv->regs + TSI721_DEV_CHAN_INTE); |
| 1883 |
ch_inte |= TSI721_INT_OMSG_CHAN(ch); |
| 1884 |
iowrite32(ch_inte, priv->regs + TSI721_DEV_CHAN_INTE); |
| 1885 |
} |
| 1886 |
|
| 1887 |
spin_unlock(&priv->omsg_ring[ch].lock); |
| 1888 |
|
| 1889 |
if (mport->outb_msg[ch].mcback && do_callback) |
| 1890 |
mport->outb_msg[ch].mcback(mport, dev_id, ch, tx_slot); |
| 1891 |
} |
| 1892 |
|
| 1893 |
/** |
| 1894 |
* tsi721_open_outb_mbox - Initialize Tsi721 outbound mailbox |
| 1895 |
* @mport: Master port implementing Outbound Messaging Engine |
| 1896 |
* @dev_id: Device specific pointer to pass on event |
| 1897 |
* @mbox: Mailbox to open |
| 1898 |
* @entries: Number of entries in the outbound mailbox ring |
| 1899 |
* |
| 1900 |
* Returns: %0 on success or -errno value on failure. |
| 1901 |
*/ |
| 1902 |
static int tsi721_open_outb_mbox(struct rio_mport *mport, void *dev_id, |
| 1903 |
int mbox, int entries) |
| 1904 |
{ |
| 1905 |
struct tsi721_device *priv = mport->priv; |
| 1906 |
struct tsi721_omsg_desc *bd_ptr; |
| 1907 |
int i, rc = 0; |
| 1908 |
|
| 1909 |
if ((entries < TSI721_OMSGD_MIN_RING_SIZE) || |
| 1910 |
(entries > (TSI721_OMSGD_RING_SIZE)) || |
| 1911 |
(!is_power_of_2(entries)) || mbox >= RIO_MAX_MBOX) { |
| 1912 |
rc = -EINVAL; |
| 1913 |
goto out; |
| 1914 |
} |
| 1915 |
|
| 1916 |
if ((mbox_sel & (1 << mbox)) == 0) { |
| 1917 |
rc = -ENODEV; |
| 1918 |
goto out; |
| 1919 |
} |
| 1920 |
|
| 1921 |
priv->omsg_ring[mbox].dev_id = dev_id; |
| 1922 |
priv->omsg_ring[mbox].size = entries; |
| 1923 |
priv->omsg_ring[mbox].sts_rdptr = 0; |
| 1924 |
spin_lock_init(&priv->omsg_ring[mbox].lock); |
| 1925 |
|
| 1926 |
/* Outbound Msg Buffer allocation based on |
| 1927 |
the number of maximum descriptor entries */ |
| 1928 |
for (i = 0; i < entries; i++) { |
| 1929 |
priv->omsg_ring[mbox].omq_base[i] = |
| 1930 |
dma_alloc_coherent( |
| 1931 |
&priv->pdev->dev, TSI721_MSG_BUFFER_SIZE, |
| 1932 |
&priv->omsg_ring[mbox].omq_phys[i], |
| 1933 |
GFP_KERNEL); |
| 1934 |
if (priv->omsg_ring[mbox].omq_base[i] == NULL) { |
| 1935 |
tsi_debug(OMSG, &priv->pdev->dev, |
| 1936 |
"ENOMEM for OB_MSG_%d data buffer", mbox); |
| 1937 |
rc = -ENOMEM; |
| 1938 |
goto out_buf; |
| 1939 |
} |
| 1940 |
} |
| 1941 |
|
| 1942 |
/* Outbound message descriptor allocation */ |
| 1943 |
priv->omsg_ring[mbox].omd_base = dma_alloc_coherent( |
| 1944 |
&priv->pdev->dev, |
| 1945 |
(entries + 1) * sizeof(struct tsi721_omsg_desc), |
| 1946 |
&priv->omsg_ring[mbox].omd_phys, GFP_KERNEL); |
| 1947 |
if (priv->omsg_ring[mbox].omd_base == NULL) { |
| 1948 |
tsi_debug(OMSG, &priv->pdev->dev, |
| 1949 |
"ENOMEM for OB_MSG_%d descriptor memory", mbox); |
| 1950 |
rc = -ENOMEM; |
| 1951 |
goto out_buf; |
| 1952 |
} |
| 1953 |
|
| 1954 |
priv->omsg_ring[mbox].tx_slot = 0; |
| 1955 |
|
| 1956 |
/* Outbound message descriptor status FIFO allocation */ |
| 1957 |
priv->omsg_ring[mbox].sts_size = roundup_pow_of_two(entries + 1); |
| 1958 |
priv->omsg_ring[mbox].sts_base = dma_alloc_coherent(&priv->pdev->dev, |
| 1959 |
priv->omsg_ring[mbox].sts_size * sizeof(struct tsi721_dma_sts), |
| 1960 |
&priv->omsg_ring[mbox].sts_phys, |
| 1961 |
GFP_KERNEL); |
| 1962 |
if (priv->omsg_ring[mbox].sts_base == NULL) { |
| 1963 |
tsi_debug(OMSG, &priv->pdev->dev, |
| 1964 |
"ENOMEM for OB_MSG_%d status FIFO", mbox); |
| 1965 |
rc = -ENOMEM; |
| 1966 |
goto out_desc; |
| 1967 |
} |
| 1968 |
|
| 1969 |
/* |
| 1970 |
* Configure Outbound Messaging Engine |
| 1971 |
*/ |
| 1972 |
|
| 1973 |
/* Setup Outbound Message descriptor pointer */ |
| 1974 |
iowrite32(((u64)priv->omsg_ring[mbox].omd_phys >> 32), |
| 1975 |
priv->regs + TSI721_OBDMAC_DPTRH(mbox)); |
| 1976 |
iowrite32(((u64)priv->omsg_ring[mbox].omd_phys & |
| 1977 |
TSI721_OBDMAC_DPTRL_MASK), |
| 1978 |
priv->regs + TSI721_OBDMAC_DPTRL(mbox)); |
| 1979 |
|
| 1980 |
/* Setup Outbound Message descriptor status FIFO */ |
| 1981 |
iowrite32(((u64)priv->omsg_ring[mbox].sts_phys >> 32), |
| 1982 |
priv->regs + TSI721_OBDMAC_DSBH(mbox)); |
| 1983 |
iowrite32(((u64)priv->omsg_ring[mbox].sts_phys & |
| 1984 |
TSI721_OBDMAC_DSBL_MASK), |
| 1985 |
priv->regs + TSI721_OBDMAC_DSBL(mbox)); |
| 1986 |
iowrite32(TSI721_DMAC_DSSZ_SIZE(priv->omsg_ring[mbox].sts_size), |
| 1987 |
priv->regs + (u32)TSI721_OBDMAC_DSSZ(mbox)); |
| 1988 |
|
| 1989 |
/* Enable interrupts */ |
| 1990 |
|
| 1991 |
#ifdef CONFIG_PCI_MSI |
| 1992 |
if (priv->flags & TSI721_USING_MSIX) { |
| 1993 |
int idx = TSI721_VECT_OMB0_DONE + mbox; |
| 1994 |
|
| 1995 |
/* Request interrupt service if we are in MSI-X mode */ |
| 1996 |
rc = request_irq(priv->msix[idx].vector, tsi721_omsg_msix, 0, |
| 1997 |
priv->msix[idx].irq_name, (void *)priv); |
| 1998 |
|
| 1999 |
if (rc) { |
| 2000 |
tsi_debug(OMSG, &priv->pdev->dev, |
| 2001 |
"Unable to get MSI-X IRQ for OBOX%d-DONE", |
| 2002 |
mbox); |
| 2003 |
goto out_stat; |
| 2004 |
} |
| 2005 |
|
| 2006 |
idx = TSI721_VECT_OMB0_INT + mbox; |
| 2007 |
rc = request_irq(priv->msix[idx].vector, tsi721_omsg_msix, 0, |
| 2008 |
priv->msix[idx].irq_name, (void *)priv); |
| 2009 |
|
| 2010 |
if (rc) { |
| 2011 |
tsi_debug(OMSG, &priv->pdev->dev, |
| 2012 |
"Unable to get MSI-X IRQ for MBOX%d-INT", mbox); |
| 2013 |
idx = TSI721_VECT_OMB0_DONE + mbox; |
| 2014 |
free_irq(priv->msix[idx].vector, (void *)priv); |
| 2015 |
goto out_stat; |
| 2016 |
} |
| 2017 |
} |
| 2018 |
#endif /* CONFIG_PCI_MSI */ |
| 2019 |
|
| 2020 |
tsi721_omsg_interrupt_enable(priv, mbox, TSI721_OBDMAC_INT_ALL); |
| 2021 |
|
| 2022 |
/* Initialize Outbound Message descriptors ring */ |
| 2023 |
bd_ptr = priv->omsg_ring[mbox].omd_base; |
| 2024 |
bd_ptr[entries].type_id = cpu_to_le32(DTYPE5 << 29); |
| 2025 |
bd_ptr[entries].msg_info = 0; |
| 2026 |
bd_ptr[entries].next_lo = |
| 2027 |
cpu_to_le32((u64)priv->omsg_ring[mbox].omd_phys & |
| 2028 |
TSI721_OBDMAC_DPTRL_MASK); |
| 2029 |
bd_ptr[entries].next_hi = |
| 2030 |
cpu_to_le32((u64)priv->omsg_ring[mbox].omd_phys >> 32); |
| 2031 |
priv->omsg_ring[mbox].wr_count = 0; |
| 2032 |
mb(); |
| 2033 |
|
| 2034 |
/* Initialize Outbound Message engine */ |
| 2035 |
iowrite32(TSI721_OBDMAC_CTL_RETRY_THR | TSI721_OBDMAC_CTL_INIT, |
| 2036 |
priv->regs + TSI721_OBDMAC_CTL(mbox)); |
| 2037 |
ioread32(priv->regs + TSI721_OBDMAC_DWRCNT(mbox)); |
| 2038 |
udelay(10); |
| 2039 |
|
| 2040 |
priv->omsg_init[mbox] = 1; |
| 2041 |
|
| 2042 |
return 0; |
| 2043 |
|
| 2044 |
#ifdef CONFIG_PCI_MSI |
| 2045 |
out_stat: |
| 2046 |
dma_free_coherent(&priv->pdev->dev, |
| 2047 |
priv->omsg_ring[mbox].sts_size * sizeof(struct tsi721_dma_sts), |
| 2048 |
priv->omsg_ring[mbox].sts_base, |
| 2049 |
priv->omsg_ring[mbox].sts_phys); |
| 2050 |
|
| 2051 |
priv->omsg_ring[mbox].sts_base = NULL; |
| 2052 |
#endif /* CONFIG_PCI_MSI */ |
| 2053 |
|
| 2054 |
out_desc: |
| 2055 |
dma_free_coherent(&priv->pdev->dev, |
| 2056 |
(entries + 1) * sizeof(struct tsi721_omsg_desc), |
| 2057 |
priv->omsg_ring[mbox].omd_base, |
| 2058 |
priv->omsg_ring[mbox].omd_phys); |
| 2059 |
|
| 2060 |
priv->omsg_ring[mbox].omd_base = NULL; |
| 2061 |
|
| 2062 |
out_buf: |
| 2063 |
for (i = 0; i < priv->omsg_ring[mbox].size; i++) { |
| 2064 |
if (priv->omsg_ring[mbox].omq_base[i]) { |
| 2065 |
dma_free_coherent(&priv->pdev->dev, |
| 2066 |
TSI721_MSG_BUFFER_SIZE, |
| 2067 |
priv->omsg_ring[mbox].omq_base[i], |
| 2068 |
priv->omsg_ring[mbox].omq_phys[i]); |
| 2069 |
|
| 2070 |
priv->omsg_ring[mbox].omq_base[i] = NULL; |
| 2071 |
} |
| 2072 |
} |
| 2073 |
|
| 2074 |
out: |
| 2075 |
return rc; |
| 2076 |
} |
| 2077 |
|
| 2078 |
/** |
| 2079 |
* tsi721_close_outb_mbox - Close Tsi721 outbound mailbox |
| 2080 |
* @mport: Master port implementing the outbound message unit |
| 2081 |
* @mbox: Mailbox to close |
| 2082 |
*/ |
| 2083 |
static void tsi721_close_outb_mbox(struct rio_mport *mport, int mbox) |
| 2084 |
{ |
| 2085 |
struct tsi721_device *priv = mport->priv; |
| 2086 |
u32 i; |
| 2087 |
|
| 2088 |
if (!priv->omsg_init[mbox]) |
| 2089 |
return; |
| 2090 |
priv->omsg_init[mbox] = 0; |
| 2091 |
|
| 2092 |
/* Disable Interrupts */ |
| 2093 |
|
| 2094 |
tsi721_omsg_interrupt_disable(priv, mbox, TSI721_OBDMAC_INT_ALL); |
| 2095 |
|
| 2096 |
#ifdef CONFIG_PCI_MSI |
| 2097 |
if (priv->flags & TSI721_USING_MSIX) { |
| 2098 |
free_irq(priv->msix[TSI721_VECT_OMB0_DONE + mbox].vector, |
| 2099 |
(void *)priv); |
| 2100 |
free_irq(priv->msix[TSI721_VECT_OMB0_INT + mbox].vector, |
| 2101 |
(void *)priv); |
| 2102 |
} |
| 2103 |
#endif /* CONFIG_PCI_MSI */ |
| 2104 |
|
| 2105 |
/* Free OMSG Descriptor Status FIFO */ |
| 2106 |
dma_free_coherent(&priv->pdev->dev, |
| 2107 |
priv->omsg_ring[mbox].sts_size * sizeof(struct tsi721_dma_sts), |
| 2108 |
priv->omsg_ring[mbox].sts_base, |
| 2109 |
priv->omsg_ring[mbox].sts_phys); |
| 2110 |
|
| 2111 |
priv->omsg_ring[mbox].sts_base = NULL; |
| 2112 |
|
| 2113 |
/* Free OMSG descriptors */ |
| 2114 |
dma_free_coherent(&priv->pdev->dev, |
| 2115 |
(priv->omsg_ring[mbox].size + 1) * |
| 2116 |
sizeof(struct tsi721_omsg_desc), |
| 2117 |
priv->omsg_ring[mbox].omd_base, |
| 2118 |
priv->omsg_ring[mbox].omd_phys); |
| 2119 |
|
| 2120 |
priv->omsg_ring[mbox].omd_base = NULL; |
| 2121 |
|
| 2122 |
/* Free message buffers */ |
| 2123 |
for (i = 0; i < priv->omsg_ring[mbox].size; i++) { |
| 2124 |
if (priv->omsg_ring[mbox].omq_base[i]) { |
| 2125 |
dma_free_coherent(&priv->pdev->dev, |
| 2126 |
TSI721_MSG_BUFFER_SIZE, |
| 2127 |
priv->omsg_ring[mbox].omq_base[i], |
| 2128 |
priv->omsg_ring[mbox].omq_phys[i]); |
| 2129 |
|
| 2130 |
priv->omsg_ring[mbox].omq_base[i] = NULL; |
| 2131 |
} |
| 2132 |
} |
| 2133 |
} |
| 2134 |
|
| 2135 |
/** |
| 2136 |
* tsi721_imsg_handler - Inbound Message Interrupt Handler |
| 2137 |
* @priv: pointer to tsi721 private data |
| 2138 |
* @ch: inbound message channel number to service |
| 2139 |
* |
| 2140 |
* Services channel interrupts from inbound messaging engine. |
| 2141 |
*/ |
| 2142 |
static void tsi721_imsg_handler(struct tsi721_device *priv, int ch) |
| 2143 |
{ |
| 2144 |
u32 mbox = ch - 4; |
| 2145 |
u32 imsg_int; |
| 2146 |
struct rio_mport *mport = &priv->mport; |
| 2147 |
|
| 2148 |
spin_lock(&priv->imsg_ring[mbox].lock); |
| 2149 |
|
| 2150 |
imsg_int = ioread32(priv->regs + TSI721_IBDMAC_INT(ch)); |
| 2151 |
|
| 2152 |
if (imsg_int & TSI721_IBDMAC_INT_SRTO) |
| 2153 |
tsi_info(&priv->pdev->dev, "IB MBOX%d SRIO timeout", mbox); |
| 2154 |
|
| 2155 |
if (imsg_int & TSI721_IBDMAC_INT_PC_ERROR) |
| 2156 |
tsi_info(&priv->pdev->dev, "IB MBOX%d PCIe error", mbox); |
| 2157 |
|
| 2158 |
if (imsg_int & TSI721_IBDMAC_INT_FQ_LOW) |
| 2159 |
tsi_info(&priv->pdev->dev, "IB MBOX%d IB free queue low", mbox); |
| 2160 |
|
| 2161 |
/* Clear IB channel interrupts */ |
| 2162 |
iowrite32(imsg_int, priv->regs + TSI721_IBDMAC_INT(ch)); |
| 2163 |
|
| 2164 |
/* If an IB Msg is received notify the upper layer */ |
| 2165 |
if (imsg_int & TSI721_IBDMAC_INT_DQ_RCV && |
| 2166 |
mport->inb_msg[mbox].mcback) |
| 2167 |
mport->inb_msg[mbox].mcback(mport, |
| 2168 |
priv->imsg_ring[mbox].dev_id, mbox, -1); |
| 2169 |
|
| 2170 |
if (!(priv->flags & TSI721_USING_MSIX)) { |
| 2171 |
u32 ch_inte; |
| 2172 |
|
| 2173 |
/* Re-enable channel interrupts */ |
| 2174 |
ch_inte = ioread32(priv->regs + TSI721_DEV_CHAN_INTE); |
| 2175 |
ch_inte |= TSI721_INT_IMSG_CHAN(ch); |
| 2176 |
iowrite32(ch_inte, priv->regs + TSI721_DEV_CHAN_INTE); |
| 2177 |
} |
| 2178 |
|
| 2179 |
spin_unlock(&priv->imsg_ring[mbox].lock); |
| 2180 |
} |
| 2181 |
|
| 2182 |
/** |
| 2183 |
* tsi721_open_inb_mbox - Initialize Tsi721 inbound mailbox |
| 2184 |
* @mport: Master port implementing the Inbound Messaging Engine |
| 2185 |
* @dev_id: Device specific pointer to pass on event |
| 2186 |
* @mbox: Mailbox to open |
| 2187 |
* @entries: Number of entries in the inbound mailbox ring |
| 2188 |
* |
| 2189 |
* Returns: %0 on success or -errno value on failure. |
| 2190 |
*/ |
| 2191 |
static int tsi721_open_inb_mbox(struct rio_mport *mport, void *dev_id, |
| 2192 |
int mbox, int entries) |
| 2193 |
{ |
| 2194 |
struct tsi721_device *priv = mport->priv; |
| 2195 |
int ch = mbox + 4; |
| 2196 |
int i; |
| 2197 |
u64 *free_ptr; |
| 2198 |
int rc = 0; |
| 2199 |
|
| 2200 |
if ((entries < TSI721_IMSGD_MIN_RING_SIZE) || |
| 2201 |
(entries > TSI721_IMSGD_RING_SIZE) || |
| 2202 |
(!is_power_of_2(entries)) || mbox >= RIO_MAX_MBOX) { |
| 2203 |
rc = -EINVAL; |
| 2204 |
goto out; |
| 2205 |
} |
| 2206 |
|
| 2207 |
if ((mbox_sel & (1 << mbox)) == 0) { |
| 2208 |
rc = -ENODEV; |
| 2209 |
goto out; |
| 2210 |
} |
| 2211 |
|
| 2212 |
/* Initialize IB Messaging Ring */ |
| 2213 |
priv->imsg_ring[mbox].dev_id = dev_id; |
| 2214 |
priv->imsg_ring[mbox].size = entries; |
| 2215 |
priv->imsg_ring[mbox].rx_slot = 0; |
| 2216 |
priv->imsg_ring[mbox].desc_rdptr = 0; |
| 2217 |
priv->imsg_ring[mbox].fq_wrptr = 0; |
| 2218 |
for (i = 0; i < priv->imsg_ring[mbox].size; i++) |
| 2219 |
priv->imsg_ring[mbox].imq_base[i] = NULL; |
| 2220 |
spin_lock_init(&priv->imsg_ring[mbox].lock); |
| 2221 |
|
| 2222 |
/* Allocate buffers for incoming messages */ |
| 2223 |
priv->imsg_ring[mbox].buf_base = |
| 2224 |
dma_alloc_coherent(&priv->pdev->dev, |
| 2225 |
entries * TSI721_MSG_BUFFER_SIZE, |
| 2226 |
&priv->imsg_ring[mbox].buf_phys, |
| 2227 |
GFP_KERNEL); |
| 2228 |
|
| 2229 |
if (priv->imsg_ring[mbox].buf_base == NULL) { |
| 2230 |
tsi_err(&priv->pdev->dev, |
| 2231 |
"Failed to allocate buffers for IB MBOX%d", mbox); |
| 2232 |
rc = -ENOMEM; |
| 2233 |
goto out; |
| 2234 |
} |
| 2235 |
|
| 2236 |
/* Allocate memory for circular free list */ |
| 2237 |
priv->imsg_ring[mbox].imfq_base = |
| 2238 |
dma_alloc_coherent(&priv->pdev->dev, |
| 2239 |
entries * 8, |
| 2240 |
&priv->imsg_ring[mbox].imfq_phys, |
| 2241 |
GFP_KERNEL); |
| 2242 |
|
| 2243 |
if (priv->imsg_ring[mbox].imfq_base == NULL) { |
| 2244 |
tsi_err(&priv->pdev->dev, |
| 2245 |
"Failed to allocate free queue for IB MBOX%d", mbox); |
| 2246 |
rc = -ENOMEM; |
| 2247 |
goto out_buf; |
| 2248 |
} |
| 2249 |
|
| 2250 |
/* Allocate memory for Inbound message descriptors */ |
| 2251 |
priv->imsg_ring[mbox].imd_base = |
| 2252 |
dma_alloc_coherent(&priv->pdev->dev, |
| 2253 |
entries * sizeof(struct tsi721_imsg_desc), |
| 2254 |
&priv->imsg_ring[mbox].imd_phys, GFP_KERNEL); |
| 2255 |
|
| 2256 |
if (priv->imsg_ring[mbox].imd_base == NULL) { |
| 2257 |
tsi_err(&priv->pdev->dev, |
| 2258 |
"Failed to allocate descriptor memory for IB MBOX%d", |
| 2259 |
mbox); |
| 2260 |
rc = -ENOMEM; |
| 2261 |
goto out_dma; |
| 2262 |
} |
| 2263 |
|
| 2264 |
/* Fill free buffer pointer list */ |
| 2265 |
free_ptr = priv->imsg_ring[mbox].imfq_base; |
| 2266 |
for (i = 0; i < entries; i++) |
| 2267 |
free_ptr[i] = cpu_to_le64( |
| 2268 |
(u64)(priv->imsg_ring[mbox].buf_phys) + |
| 2269 |
i * 0x1000); |
| 2270 |
|
| 2271 |
mb(); |
| 2272 |
|
| 2273 |
/* |
| 2274 |
* For mapping of inbound SRIO Messages into appropriate queues we need |
| 2275 |
* to set Inbound Device ID register in the messaging engine. We do it |
| 2276 |
* once when first inbound mailbox is requested. |
| 2277 |
*/ |
| 2278 |
if (!(priv->flags & TSI721_IMSGID_SET)) { |
| 2279 |
iowrite32((u32)priv->mport.host_deviceid, |
| 2280 |
priv->regs + TSI721_IB_DEVID); |
| 2281 |
priv->flags |= TSI721_IMSGID_SET; |
| 2282 |
} |
| 2283 |
|
| 2284 |
/* |
| 2285 |
* Configure Inbound Messaging channel (ch = mbox + 4) |
| 2286 |
*/ |
| 2287 |
|
| 2288 |
/* Setup Inbound Message free queue */ |
| 2289 |
iowrite32(((u64)priv->imsg_ring[mbox].imfq_phys >> 32), |
| 2290 |
priv->regs + TSI721_IBDMAC_FQBH(ch)); |
| 2291 |
iowrite32(((u64)priv->imsg_ring[mbox].imfq_phys & |
| 2292 |
TSI721_IBDMAC_FQBL_MASK), |
| 2293 |
priv->regs+TSI721_IBDMAC_FQBL(ch)); |
| 2294 |
iowrite32(TSI721_DMAC_DSSZ_SIZE(entries), |
| 2295 |
priv->regs + TSI721_IBDMAC_FQSZ(ch)); |
| 2296 |
|
| 2297 |
/* Setup Inbound Message descriptor queue */ |
| 2298 |
iowrite32(((u64)priv->imsg_ring[mbox].imd_phys >> 32), |
| 2299 |
priv->regs + TSI721_IBDMAC_DQBH(ch)); |
| 2300 |
iowrite32(((u32)priv->imsg_ring[mbox].imd_phys & |
| 2301 |
(u32)TSI721_IBDMAC_DQBL_MASK), |
| 2302 |
priv->regs+TSI721_IBDMAC_DQBL(ch)); |
| 2303 |
iowrite32(TSI721_DMAC_DSSZ_SIZE(entries), |
| 2304 |
priv->regs + TSI721_IBDMAC_DQSZ(ch)); |
| 2305 |
|
| 2306 |
/* Enable interrupts */ |
| 2307 |
|
| 2308 |
#ifdef CONFIG_PCI_MSI |
| 2309 |
if (priv->flags & TSI721_USING_MSIX) { |
| 2310 |
int idx = TSI721_VECT_IMB0_RCV + mbox; |
| 2311 |
|
| 2312 |
/* Request interrupt service if we are in MSI-X mode */ |
| 2313 |
rc = request_irq(priv->msix[idx].vector, tsi721_imsg_msix, 0, |
| 2314 |
priv->msix[idx].irq_name, (void *)priv); |
| 2315 |
|
| 2316 |
if (rc) { |
| 2317 |
tsi_debug(IMSG, &priv->pdev->dev, |
| 2318 |
"Unable to get MSI-X IRQ for IBOX%d-DONE", |
| 2319 |
mbox); |
| 2320 |
goto out_desc; |
| 2321 |
} |
| 2322 |
|
| 2323 |
idx = TSI721_VECT_IMB0_INT + mbox; |
| 2324 |
rc = request_irq(priv->msix[idx].vector, tsi721_imsg_msix, 0, |
| 2325 |
priv->msix[idx].irq_name, (void *)priv); |
| 2326 |
|
| 2327 |
if (rc) { |
| 2328 |
tsi_debug(IMSG, &priv->pdev->dev, |
| 2329 |
"Unable to get MSI-X IRQ for IBOX%d-INT", mbox); |
| 2330 |
free_irq( |
| 2331 |
priv->msix[TSI721_VECT_IMB0_RCV + mbox].vector, |
| 2332 |
(void *)priv); |
| 2333 |
goto out_desc; |
| 2334 |
} |
| 2335 |
} |
| 2336 |
#endif /* CONFIG_PCI_MSI */ |
| 2337 |
|
| 2338 |
tsi721_imsg_interrupt_enable(priv, ch, TSI721_IBDMAC_INT_ALL); |
| 2339 |
|
| 2340 |
/* Initialize Inbound Message Engine */ |
| 2341 |
iowrite32(TSI721_IBDMAC_CTL_INIT, priv->regs + TSI721_IBDMAC_CTL(ch)); |
| 2342 |
ioread32(priv->regs + TSI721_IBDMAC_CTL(ch)); |
| 2343 |
udelay(10); |
| 2344 |
priv->imsg_ring[mbox].fq_wrptr = entries - 1; |
| 2345 |
iowrite32(entries - 1, priv->regs + TSI721_IBDMAC_FQWP(ch)); |
| 2346 |
|
| 2347 |
priv->imsg_init[mbox] = 1; |
| 2348 |
return 0; |
| 2349 |
|
| 2350 |
#ifdef CONFIG_PCI_MSI |
| 2351 |
out_desc: |
| 2352 |
dma_free_coherent(&priv->pdev->dev, |
| 2353 |
priv->imsg_ring[mbox].size * sizeof(struct tsi721_imsg_desc), |
| 2354 |
priv->imsg_ring[mbox].imd_base, |
| 2355 |
priv->imsg_ring[mbox].imd_phys); |
| 2356 |
|
| 2357 |
priv->imsg_ring[mbox].imd_base = NULL; |
| 2358 |
#endif /* CONFIG_PCI_MSI */ |
| 2359 |
|
| 2360 |
out_dma: |
| 2361 |
dma_free_coherent(&priv->pdev->dev, |
| 2362 |
priv->imsg_ring[mbox].size * 8, |
| 2363 |
priv->imsg_ring[mbox].imfq_base, |
| 2364 |
priv->imsg_ring[mbox].imfq_phys); |
| 2365 |
|
| 2366 |
priv->imsg_ring[mbox].imfq_base = NULL; |
| 2367 |
|
| 2368 |
out_buf: |
| 2369 |
dma_free_coherent(&priv->pdev->dev, |
| 2370 |
priv->imsg_ring[mbox].size * TSI721_MSG_BUFFER_SIZE, |
| 2371 |
priv->imsg_ring[mbox].buf_base, |
| 2372 |
priv->imsg_ring[mbox].buf_phys); |
| 2373 |
|
| 2374 |
priv->imsg_ring[mbox].buf_base = NULL; |
| 2375 |
|
| 2376 |
out: |
| 2377 |
return rc; |
| 2378 |
} |
| 2379 |
|
| 2380 |
/** |
| 2381 |
* tsi721_close_inb_mbox - Shut down Tsi721 inbound mailbox |
| 2382 |
* @mport: Master port implementing the Inbound Messaging Engine |
| 2383 |
* @mbox: Mailbox to close |
| 2384 |
*/ |
| 2385 |
static void tsi721_close_inb_mbox(struct rio_mport *mport, int mbox) |
| 2386 |
{ |
| 2387 |
struct tsi721_device *priv = mport->priv; |
| 2388 |
u32 rx_slot; |
| 2389 |
int ch = mbox + 4; |
| 2390 |
|
| 2391 |
if (!priv->imsg_init[mbox]) /* mbox isn't initialized yet */ |
| 2392 |
return; |
| 2393 |
priv->imsg_init[mbox] = 0; |
| 2394 |
|
| 2395 |
/* Disable Inbound Messaging Engine */ |
| 2396 |
|
| 2397 |
/* Disable Interrupts */ |
| 2398 |
tsi721_imsg_interrupt_disable(priv, ch, TSI721_OBDMAC_INT_MASK); |
| 2399 |
|
| 2400 |
#ifdef CONFIG_PCI_MSI |
| 2401 |
if (priv->flags & TSI721_USING_MSIX) { |
| 2402 |
free_irq(priv->msix[TSI721_VECT_IMB0_RCV + mbox].vector, |
| 2403 |
(void *)priv); |
| 2404 |
free_irq(priv->msix[TSI721_VECT_IMB0_INT + mbox].vector, |
| 2405 |
(void *)priv); |
| 2406 |
} |
| 2407 |
#endif /* CONFIG_PCI_MSI */ |
| 2408 |
|
| 2409 |
/* Clear Inbound Buffer Queue */ |
| 2410 |
for (rx_slot = 0; rx_slot < priv->imsg_ring[mbox].size; rx_slot++) |
| 2411 |
priv->imsg_ring[mbox].imq_base[rx_slot] = NULL; |
| 2412 |
|
| 2413 |
/* Free memory allocated for message buffers */ |
| 2414 |
dma_free_coherent(&priv->pdev->dev, |
| 2415 |
priv->imsg_ring[mbox].size * TSI721_MSG_BUFFER_SIZE, |
| 2416 |
priv->imsg_ring[mbox].buf_base, |
| 2417 |
priv->imsg_ring[mbox].buf_phys); |
| 2418 |
|
| 2419 |
priv->imsg_ring[mbox].buf_base = NULL; |
| 2420 |
|
| 2421 |
/* Free memory allocated for free pointr list */ |
| 2422 |
dma_free_coherent(&priv->pdev->dev, |
| 2423 |
priv->imsg_ring[mbox].size * 8, |
| 2424 |
priv->imsg_ring[mbox].imfq_base, |
| 2425 |
priv->imsg_ring[mbox].imfq_phys); |
| 2426 |
|
| 2427 |
priv->imsg_ring[mbox].imfq_base = NULL; |
| 2428 |
|
| 2429 |
/* Free memory allocated for RX descriptors */ |
| 2430 |
dma_free_coherent(&priv->pdev->dev, |
| 2431 |
priv->imsg_ring[mbox].size * sizeof(struct tsi721_imsg_desc), |
| 2432 |
priv->imsg_ring[mbox].imd_base, |
| 2433 |
priv->imsg_ring[mbox].imd_phys); |
| 2434 |
|
| 2435 |
priv->imsg_ring[mbox].imd_base = NULL; |
| 2436 |
} |
| 2437 |
|
| 2438 |
/** |
| 2439 |
* tsi721_add_inb_buffer - Add buffer to the Tsi721 inbound message queue |
| 2440 |
* @mport: Master port implementing the Inbound Messaging Engine |
| 2441 |
* @mbox: Inbound mailbox number |
| 2442 |
* @buf: Buffer to add to inbound queue |
| 2443 |
* |
| 2444 |
* Returns: %0 on success or -errno value on failure. |
| 2445 |
*/ |
| 2446 |
static int tsi721_add_inb_buffer(struct rio_mport *mport, int mbox, void *buf) |
| 2447 |
{ |
| 2448 |
struct tsi721_device *priv = mport->priv; |
| 2449 |
u32 rx_slot; |
| 2450 |
int rc = 0; |
| 2451 |
|
| 2452 |
rx_slot = priv->imsg_ring[mbox].rx_slot; |
| 2453 |
if (priv->imsg_ring[mbox].imq_base[rx_slot]) { |
| 2454 |
tsi_err(&priv->pdev->dev, |
| 2455 |
"Error adding inbound buffer %d, buffer exists", |
| 2456 |
rx_slot); |
| 2457 |
rc = -EINVAL; |
| 2458 |
goto out; |
| 2459 |
} |
| 2460 |
|
| 2461 |
priv->imsg_ring[mbox].imq_base[rx_slot] = buf; |
| 2462 |
|
| 2463 |
if (++priv->imsg_ring[mbox].rx_slot == priv->imsg_ring[mbox].size) |
| 2464 |
priv->imsg_ring[mbox].rx_slot = 0; |
| 2465 |
|
| 2466 |
out: |
| 2467 |
return rc; |
| 2468 |
} |
| 2469 |
|
| 2470 |
/** |
| 2471 |
* tsi721_get_inb_message - Fetch inbound message from the Tsi721 MSG Queue |
| 2472 |
* @mport: Master port implementing the Inbound Messaging Engine |
| 2473 |
* @mbox: Inbound mailbox number |
| 2474 |
* |
| 2475 |
* Returns: pointer to the message on success or %NULL on failure. |
| 2476 |
*/ |
| 2477 |
static void *tsi721_get_inb_message(struct rio_mport *mport, int mbox) |
| 2478 |
{ |
| 2479 |
struct tsi721_device *priv = mport->priv; |
| 2480 |
struct tsi721_imsg_desc *desc; |
| 2481 |
u32 rx_slot; |
| 2482 |
void *rx_virt = NULL; |
| 2483 |
u64 rx_phys; |
| 2484 |
void *buf = NULL; |
| 2485 |
u64 *free_ptr; |
| 2486 |
int ch = mbox + 4; |
| 2487 |
int msg_size; |
| 2488 |
|
| 2489 |
if (!priv->imsg_init[mbox]) |
| 2490 |
return NULL; |
| 2491 |
|
| 2492 |
desc = priv->imsg_ring[mbox].imd_base; |
| 2493 |
desc += priv->imsg_ring[mbox].desc_rdptr; |
| 2494 |
|
| 2495 |
if (!(le32_to_cpu(desc->msg_info) & TSI721_IMD_HO)) |
| 2496 |
goto out; |
| 2497 |
|
| 2498 |
rx_slot = priv->imsg_ring[mbox].rx_slot; |
| 2499 |
while (priv->imsg_ring[mbox].imq_base[rx_slot] == NULL) { |
| 2500 |
if (++rx_slot == priv->imsg_ring[mbox].size) |
| 2501 |
rx_slot = 0; |
| 2502 |
} |
| 2503 |
|
| 2504 |
rx_phys = ((u64)le32_to_cpu(desc->bufptr_hi) << 32) | |
| 2505 |
le32_to_cpu(desc->bufptr_lo); |
| 2506 |
|
| 2507 |
rx_virt = priv->imsg_ring[mbox].buf_base + |
| 2508 |
(rx_phys - (u64)priv->imsg_ring[mbox].buf_phys); |
| 2509 |
|
| 2510 |
buf = priv->imsg_ring[mbox].imq_base[rx_slot]; |
| 2511 |
msg_size = le32_to_cpu(desc->msg_info) & TSI721_IMD_BCOUNT; |
| 2512 |
if (msg_size == 0) |
| 2513 |
msg_size = RIO_MAX_MSG_SIZE; |
| 2514 |
|
| 2515 |
memcpy(buf, rx_virt, msg_size); |
| 2516 |
priv->imsg_ring[mbox].imq_base[rx_slot] = NULL; |
| 2517 |
|
| 2518 |
desc->msg_info &= cpu_to_le32(~TSI721_IMD_HO); |
| 2519 |
if (++priv->imsg_ring[mbox].desc_rdptr == priv->imsg_ring[mbox].size) |
| 2520 |
priv->imsg_ring[mbox].desc_rdptr = 0; |
| 2521 |
|
| 2522 |
iowrite32(priv->imsg_ring[mbox].desc_rdptr, |
| 2523 |
priv->regs + TSI721_IBDMAC_DQRP(ch)); |
| 2524 |
|
| 2525 |
/* Return free buffer into the pointer list */ |
| 2526 |
free_ptr = priv->imsg_ring[mbox].imfq_base; |
| 2527 |
free_ptr[priv->imsg_ring[mbox].fq_wrptr] = cpu_to_le64(rx_phys); |
| 2528 |
|
| 2529 |
if (++priv->imsg_ring[mbox].fq_wrptr == priv->imsg_ring[mbox].size) |
| 2530 |
priv->imsg_ring[mbox].fq_wrptr = 0; |
| 2531 |
|
| 2532 |
iowrite32(priv->imsg_ring[mbox].fq_wrptr, |
| 2533 |
priv->regs + TSI721_IBDMAC_FQWP(ch)); |
| 2534 |
out: |
| 2535 |
return buf; |
| 2536 |
} |
| 2537 |
|
| 2538 |
/** |
| 2539 |
* tsi721_messages_init - Initialization of Messaging Engine |
| 2540 |
* @priv: pointer to tsi721 private data |
| 2541 |
* |
| 2542 |
* Configures Tsi721 messaging engine. |
| 2543 |
* |
| 2544 |
* Returns: %0 |
| 2545 |
*/ |
| 2546 |
static int tsi721_messages_init(struct tsi721_device *priv) |
| 2547 |
{ |
| 2548 |
int ch; |
| 2549 |
|
| 2550 |
iowrite32(0, priv->regs + TSI721_SMSG_ECC_LOG); |
| 2551 |
iowrite32(0, priv->regs + TSI721_RETRY_GEN_CNT); |
| 2552 |
iowrite32(0, priv->regs + TSI721_RETRY_RX_CNT); |
| 2553 |
|
| 2554 |
/* Set SRIO Message Request/Response Timeout */ |
| 2555 |
iowrite32(TSI721_RQRPTO_VAL, priv->regs + TSI721_RQRPTO); |
| 2556 |
|
| 2557 |
/* Initialize Inbound Messaging Engine Registers */ |
| 2558 |
for (ch = 0; ch < TSI721_IMSG_CHNUM; ch++) { |
| 2559 |
/* Clear interrupt bits */ |
| 2560 |
iowrite32(TSI721_IBDMAC_INT_MASK, |
| 2561 |
priv->regs + TSI721_IBDMAC_INT(ch)); |
| 2562 |
/* Clear Status */ |
| 2563 |
iowrite32(0, priv->regs + TSI721_IBDMAC_STS(ch)); |
| 2564 |
|
| 2565 |
iowrite32(TSI721_SMSG_ECC_COR_LOG_MASK, |
| 2566 |
priv->regs + TSI721_SMSG_ECC_COR_LOG(ch)); |
| 2567 |
iowrite32(TSI721_SMSG_ECC_NCOR_MASK, |
| 2568 |
priv->regs + TSI721_SMSG_ECC_NCOR(ch)); |
| 2569 |
} |
| 2570 |
|
| 2571 |
return 0; |
| 2572 |
} |
| 2573 |
|
| 2574 |
/** |
| 2575 |
* tsi721_query_mport - Fetch inbound message from the Tsi721 MSG Queue |
| 2576 |
* @mport: Master port implementing the Inbound Messaging Engine |
| 2577 |
* @attr: mport device attributes |
| 2578 |
* |
| 2579 |
* Returns: pointer to the message on success or %NULL on failure. |
| 2580 |
*/ |
| 2581 |
static int tsi721_query_mport(struct rio_mport *mport, |
| 2582 |
struct rio_mport_attr *attr) |
| 2583 |
{ |
| 2584 |
struct tsi721_device *priv = mport->priv; |
| 2585 |
u32 rval; |
| 2586 |
|
| 2587 |
rval = ioread32(priv->regs + 0x100 + RIO_PORT_N_ERR_STS_CSR(0, 0)); |
| 2588 |
if (rval & RIO_PORT_N_ERR_STS_PORT_OK) { |
| 2589 |
rval = ioread32(priv->regs + 0x100 + RIO_PORT_N_CTL2_CSR(0, 0)); |
| 2590 |
attr->link_speed = (rval & RIO_PORT_N_CTL2_SEL_BAUD) >> 28; |
| 2591 |
rval = ioread32(priv->regs + 0x100 + RIO_PORT_N_CTL_CSR(0, 0)); |
| 2592 |
attr->link_width = (rval & RIO_PORT_N_CTL_IPW) >> 27; |
| 2593 |
} else |
| 2594 |
attr->link_speed = RIO_LINK_DOWN; |
| 2595 |
|
| 2596 |
#ifdef CONFIG_RAPIDIO_DMA_ENGINE |
| 2597 |
attr->flags = RIO_MPORT_DMA | RIO_MPORT_DMA_SG; |
| 2598 |
attr->dma_max_sge = 0; |
| 2599 |
attr->dma_max_size = TSI721_BDMA_MAX_BCOUNT; |
| 2600 |
attr->dma_align = 0; |
| 2601 |
#else |
| 2602 |
attr->flags = 0; |
| 2603 |
#endif |
| 2604 |
return 0; |
| 2605 |
} |
| 2606 |
|
| 2607 |
/** |
| 2608 |
* tsi721_disable_ints - disables all device interrupts |
| 2609 |
* @priv: pointer to tsi721 private data |
| 2610 |
*/ |
| 2611 |
static void tsi721_disable_ints(struct tsi721_device *priv) |
| 2612 |
{ |
| 2613 |
int ch; |
| 2614 |
|
| 2615 |
/* Disable all device level interrupts */ |
| 2616 |
iowrite32(0, priv->regs + TSI721_DEV_INTE); |
| 2617 |
|
| 2618 |
/* Disable all Device Channel interrupts */ |
| 2619 |
iowrite32(0, priv->regs + TSI721_DEV_CHAN_INTE); |
| 2620 |
|
| 2621 |
/* Disable all Inbound Msg Channel interrupts */ |
| 2622 |
for (ch = 0; ch < TSI721_IMSG_CHNUM; ch++) |
| 2623 |
iowrite32(0, priv->regs + TSI721_IBDMAC_INTE(ch)); |
| 2624 |
|
| 2625 |
/* Disable all Outbound Msg Channel interrupts */ |
| 2626 |
for (ch = 0; ch < TSI721_OMSG_CHNUM; ch++) |
| 2627 |
iowrite32(0, priv->regs + TSI721_OBDMAC_INTE(ch)); |
| 2628 |
|
| 2629 |
/* Disable all general messaging interrupts */ |
| 2630 |
iowrite32(0, priv->regs + TSI721_SMSG_INTE); |
| 2631 |
|
| 2632 |
/* Disable all BDMA Channel interrupts */ |
| 2633 |
for (ch = 0; ch < TSI721_DMA_MAXCH; ch++) |
| 2634 |
iowrite32(0, |
| 2635 |
priv->regs + TSI721_DMAC_BASE(ch) + TSI721_DMAC_INTE); |
| 2636 |
|
| 2637 |
/* Disable all general BDMA interrupts */ |
| 2638 |
iowrite32(0, priv->regs + TSI721_BDMA_INTE); |
| 2639 |
|
| 2640 |
/* Disable all SRIO Channel interrupts */ |
| 2641 |
for (ch = 0; ch < TSI721_SRIO_MAXCH; ch++) |
| 2642 |
iowrite32(0, priv->regs + TSI721_SR_CHINTE(ch)); |
| 2643 |
|
| 2644 |
/* Disable all general SR2PC interrupts */ |
| 2645 |
iowrite32(0, priv->regs + TSI721_SR2PC_GEN_INTE); |
| 2646 |
|
| 2647 |
/* Disable all PC2SR interrupts */ |
| 2648 |
iowrite32(0, priv->regs + TSI721_PC2SR_INTE); |
| 2649 |
|
| 2650 |
/* Disable all I2C interrupts */ |
| 2651 |
iowrite32(0, priv->regs + TSI721_I2C_INT_ENABLE); |
| 2652 |
|
| 2653 |
/* Disable SRIO MAC interrupts */ |
| 2654 |
iowrite32(0, priv->regs + TSI721_RIO_EM_INT_ENABLE); |
| 2655 |
iowrite32(0, priv->regs + TSI721_RIO_EM_DEV_INT_EN); |
| 2656 |
} |
| 2657 |
|
| 2658 |
static struct rio_ops tsi721_rio_ops = { |
| 2659 |
.lcread = tsi721_lcread, |
| 2660 |
.lcwrite = tsi721_lcwrite, |
| 2661 |
.cread = tsi721_cread_dma, |
| 2662 |
.cwrite = tsi721_cwrite_dma, |
| 2663 |
.dsend = tsi721_dsend, |
| 2664 |
.open_inb_mbox = tsi721_open_inb_mbox, |
| 2665 |
.close_inb_mbox = tsi721_close_inb_mbox, |
| 2666 |
.open_outb_mbox = tsi721_open_outb_mbox, |
| 2667 |
.close_outb_mbox = tsi721_close_outb_mbox, |
| 2668 |
.add_outb_message = tsi721_add_outb_message, |
| 2669 |
.add_inb_buffer = tsi721_add_inb_buffer, |
| 2670 |
.get_inb_message = tsi721_get_inb_message, |
| 2671 |
.map_inb = tsi721_rio_map_inb_mem, |
| 2672 |
.unmap_inb = tsi721_rio_unmap_inb_mem, |
| 2673 |
.pwenable = tsi721_pw_enable, |
| 2674 |
.query_mport = tsi721_query_mport, |
| 2675 |
.map_outb = tsi721_map_outb_win, |
| 2676 |
.unmap_outb = tsi721_unmap_outb_win, |
| 2677 |
}; |
| 2678 |
|
| 2679 |
static void tsi721_mport_release(struct device *dev) |
| 2680 |
{ |
| 2681 |
struct rio_mport *mport = to_rio_mport(dev); |
| 2682 |
|
| 2683 |
tsi_debug(EXIT, dev, "%s id=%d", mport->name, mport->id); |
| 2684 |
} |
| 2685 |
|
| 2686 |
/** |
| 2687 |
* tsi721_setup_mport - Setup Tsi721 as RapidIO subsystem master port |
| 2688 |
* @priv: pointer to tsi721 private data |
| 2689 |
* |
| 2690 |
* Configures Tsi721 as RapidIO master port. |
| 2691 |
* |
| 2692 |
* Returns: %0 on success or -errno value on failure. |
| 2693 |
*/ |
| 2694 |
static int tsi721_setup_mport(struct tsi721_device *priv) |
| 2695 |
{ |
| 2696 |
struct pci_dev *pdev = priv->pdev; |
| 2697 |
int err = 0; |
| 2698 |
struct rio_mport *mport = &priv->mport; |
| 2699 |
|
| 2700 |
err = rio_mport_initialize(mport); |
| 2701 |
if (err) |
| 2702 |
return err; |
| 2703 |
|
| 2704 |
mport->ops = &tsi721_rio_ops; |
| 2705 |
mport->index = 0; |
| 2706 |
mport->sys_size = 0; /* small system */ |
| 2707 |
mport->priv = (void *)priv; |
| 2708 |
mport->phys_efptr = 0x100; |
| 2709 |
mport->phys_rmap = 1; |
| 2710 |
mport->dev.parent = &pdev->dev; |
| 2711 |
mport->dev.release = tsi721_mport_release; |
| 2712 |
|
| 2713 |
INIT_LIST_HEAD(&mport->dbells); |
| 2714 |
|
| 2715 |
rio_init_dbell_res(&mport->riores[RIO_DOORBELL_RESOURCE], 0, 0xffff); |
| 2716 |
rio_init_mbox_res(&mport->riores[RIO_INB_MBOX_RESOURCE], 0, 3); |
| 2717 |
rio_init_mbox_res(&mport->riores[RIO_OUTB_MBOX_RESOURCE], 0, 3); |
| 2718 |
snprintf(mport->name, RIO_MAX_MPORT_NAME, "%s(%s)", |
| 2719 |
dev_driver_string(&pdev->dev), dev_name(&pdev->dev)); |
| 2720 |
|
| 2721 |
/* Hook up interrupt handler */ |
| 2722 |
|
| 2723 |
#ifdef CONFIG_PCI_MSI |
| 2724 |
if (!tsi721_enable_msix(priv)) |
| 2725 |
priv->flags |= TSI721_USING_MSIX; |
| 2726 |
else if (!pci_enable_msi(pdev)) |
| 2727 |
priv->flags |= TSI721_USING_MSI; |
| 2728 |
else |
| 2729 |
tsi_debug(MPORT, &pdev->dev, |
| 2730 |
"MSI/MSI-X is not available. Using legacy INTx."); |
| 2731 |
#endif /* CONFIG_PCI_MSI */ |
| 2732 |
|
| 2733 |
err = tsi721_request_irq(priv); |
| 2734 |
|
| 2735 |
if (err) { |
| 2736 |
tsi_err(&pdev->dev, "Unable to get PCI IRQ %02X (err=0x%x)", |
| 2737 |
pdev->irq, err); |
| 2738 |
return err; |
| 2739 |
} |
| 2740 |
|
| 2741 |
#ifdef CONFIG_RAPIDIO_DMA_ENGINE |
| 2742 |
err = tsi721_register_dma(priv); |
| 2743 |
if (err) |
| 2744 |
goto err_exit; |
| 2745 |
#endif |
| 2746 |
/* Enable SRIO link */ |
| 2747 |
iowrite32(ioread32(priv->regs + TSI721_DEVCTL) | |
| 2748 |
TSI721_DEVCTL_SRBOOT_CMPL, |
| 2749 |
priv->regs + TSI721_DEVCTL); |
| 2750 |
|
| 2751 |
if (mport->host_deviceid >= 0) |
| 2752 |
iowrite32(RIO_PORT_GEN_HOST | RIO_PORT_GEN_MASTER | |
| 2753 |
RIO_PORT_GEN_DISCOVERED, |
| 2754 |
priv->regs + (0x100 + RIO_PORT_GEN_CTL_CSR)); |
| 2755 |
else |
| 2756 |
iowrite32(0, priv->regs + (0x100 + RIO_PORT_GEN_CTL_CSR)); |
| 2757 |
|
| 2758 |
err = rio_register_mport(mport); |
| 2759 |
if (err) { |
| 2760 |
tsi721_unregister_dma(priv); |
| 2761 |
goto err_exit; |
| 2762 |
} |
| 2763 |
|
| 2764 |
return 0; |
| 2765 |
|
| 2766 |
err_exit: |
| 2767 |
tsi721_free_irq(priv); |
| 2768 |
return err; |
| 2769 |
} |
| 2770 |
|
| 2771 |
static int tsi721_probe(struct pci_dev *pdev, |
| 2772 |
const struct pci_device_id *id) |
| 2773 |
{ |
| 2774 |
struct tsi721_device *priv; |
| 2775 |
int err; |
| 2776 |
|
| 2777 |
priv = kzalloc_obj(struct tsi721_device); |
| 2778 |
if (!priv) { |
| 2779 |
err = -ENOMEM; |
| 2780 |
goto err_exit; |
| 2781 |
} |
| 2782 |
|
| 2783 |
err = pci_enable_device(pdev); |
| 2784 |
if (err) { |
| 2785 |
tsi_err(&pdev->dev, "Failed to enable PCI device"); |
| 2786 |
goto err_clean; |
| 2787 |
} |
| 2788 |
|
| 2789 |
priv->pdev = pdev; |
| 2790 |
|
| 2791 |
#ifdef DEBUG |
| 2792 |
{ |
| 2793 |
int i; |
| 2794 |
|
| 2795 |
for (i = 0; i < PCI_STD_NUM_BARS; i++) { |
| 2796 |
tsi_debug(INIT, &pdev->dev, "res%d %pR", |
| 2797 |
i, &pdev->resource[i]); |
| 2798 |
} |
| 2799 |
} |
| 2800 |
#endif |
| 2801 |
/* |
| 2802 |
* Verify BAR configuration |
| 2803 |
*/ |
| 2804 |
|
| 2805 |
/* BAR_0 (registers) must be 512KB+ in 32-bit address space */ |
| 2806 |
if (!(pci_resource_flags(pdev, BAR_0) & IORESOURCE_MEM) || |
| 2807 |
pci_resource_flags(pdev, BAR_0) & IORESOURCE_MEM_64 || |
| 2808 |
pci_resource_len(pdev, BAR_0) < TSI721_REG_SPACE_SIZE) { |
| 2809 |
tsi_err(&pdev->dev, "Missing or misconfigured CSR BAR0"); |
| 2810 |
err = -ENODEV; |
| 2811 |
goto err_disable_pdev; |
| 2812 |
} |
| 2813 |
|
| 2814 |
/* BAR_1 (outbound doorbells) must be 16MB+ in 32-bit address space */ |
| 2815 |
if (!(pci_resource_flags(pdev, BAR_1) & IORESOURCE_MEM) || |
| 2816 |
pci_resource_flags(pdev, BAR_1) & IORESOURCE_MEM_64 || |
| 2817 |
pci_resource_len(pdev, BAR_1) < TSI721_DB_WIN_SIZE) { |
| 2818 |
tsi_err(&pdev->dev, "Missing or misconfigured Doorbell BAR1"); |
| 2819 |
err = -ENODEV; |
| 2820 |
goto err_disable_pdev; |
| 2821 |
} |
| 2822 |
|
| 2823 |
/* |
| 2824 |
* BAR_2 and BAR_4 (outbound translation) must be in 64-bit PCIe address |
| 2825 |
* space. |
| 2826 |
* NOTE: BAR_2 and BAR_4 are not used by this version of driver. |
| 2827 |
* It may be a good idea to keep them disabled using HW configuration |
| 2828 |
* to save PCI memory space. |
| 2829 |
*/ |
| 2830 |
|
| 2831 |
priv->p2r_bar[0].size = priv->p2r_bar[1].size = 0; |
| 2832 |
|
| 2833 |
if (pci_resource_flags(pdev, BAR_2) & IORESOURCE_MEM_64) { |
| 2834 |
if (pci_resource_flags(pdev, BAR_2) & IORESOURCE_PREFETCH) |
| 2835 |
tsi_debug(INIT, &pdev->dev, |
| 2836 |
"Prefetchable OBW BAR2 will not be used"); |
| 2837 |
else { |
| 2838 |
priv->p2r_bar[0].base = pci_resource_start(pdev, BAR_2); |
| 2839 |
priv->p2r_bar[0].size = pci_resource_len(pdev, BAR_2); |
| 2840 |
} |
| 2841 |
} |
| 2842 |
|
| 2843 |
if (pci_resource_flags(pdev, BAR_4) & IORESOURCE_MEM_64) { |
| 2844 |
if (pci_resource_flags(pdev, BAR_4) & IORESOURCE_PREFETCH) |
| 2845 |
tsi_debug(INIT, &pdev->dev, |
| 2846 |
"Prefetchable OBW BAR4 will not be used"); |
| 2847 |
else { |
| 2848 |
priv->p2r_bar[1].base = pci_resource_start(pdev, BAR_4); |
| 2849 |
priv->p2r_bar[1].size = pci_resource_len(pdev, BAR_4); |
| 2850 |
} |
| 2851 |
} |
| 2852 |
|
| 2853 |
err = pci_request_regions(pdev, DRV_NAME); |
| 2854 |
if (err) { |
| 2855 |
tsi_err(&pdev->dev, "Unable to obtain PCI resources"); |
| 2856 |
goto err_disable_pdev; |
| 2857 |
} |
| 2858 |
|
| 2859 |
pci_set_master(pdev); |
| 2860 |
|
| 2861 |
priv->regs = pci_ioremap_bar(pdev, BAR_0); |
| 2862 |
if (!priv->regs) { |
| 2863 |
tsi_err(&pdev->dev, "Unable to map device registers space"); |
| 2864 |
err = -ENOMEM; |
| 2865 |
goto err_free_res; |
| 2866 |
} |
| 2867 |
|
| 2868 |
priv->odb_base = pci_ioremap_bar(pdev, BAR_1); |
| 2869 |
if (!priv->odb_base) { |
| 2870 |
tsi_err(&pdev->dev, "Unable to map outbound doorbells space"); |
| 2871 |
err = -ENOMEM; |
| 2872 |
goto err_unmap_bars; |
| 2873 |
} |
| 2874 |
|
| 2875 |
/* Configure DMA attributes. */ |
| 2876 |
if (dma_set_mask(&pdev->dev, DMA_BIT_MASK(64))) { |
| 2877 |
err = dma_set_mask(&pdev->dev, DMA_BIT_MASK(32)); |
| 2878 |
if (err) { |
| 2879 |
tsi_err(&pdev->dev, "Unable to set DMA mask"); |
| 2880 |
goto err_unmap_bars; |
| 2881 |
} |
| 2882 |
|
| 2883 |
if (dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(32))) |
| 2884 |
tsi_info(&pdev->dev, "Unable to set consistent DMA mask"); |
| 2885 |
} else { |
| 2886 |
err = dma_set_coherent_mask(&pdev->dev, DMA_BIT_MASK(64)); |
| 2887 |
if (err) |
| 2888 |
tsi_info(&pdev->dev, "Unable to set consistent DMA mask"); |
| 2889 |
} |
| 2890 |
|
| 2891 |
BUG_ON(!pci_is_pcie(pdev)); |
| 2892 |
|
| 2893 |
/* Clear "no snoop" and "relaxed ordering" bits. */ |
| 2894 |
pcie_capability_clear_and_set_word(pdev, PCI_EXP_DEVCTL, |
| 2895 |
PCI_EXP_DEVCTL_RELAX_EN | PCI_EXP_DEVCTL_NOSNOOP_EN, 0); |
| 2896 |
|
| 2897 |
/* Override PCIe Maximum Read Request Size setting if requested */ |
| 2898 |
if (pcie_mrrs >= 0) { |
| 2899 |
if (pcie_mrrs <= 5) |
| 2900 |
pcie_capability_clear_and_set_word(pdev, PCI_EXP_DEVCTL, |
| 2901 |
PCI_EXP_DEVCTL_READRQ, pcie_mrrs << 12); |
| 2902 |
else |
| 2903 |
tsi_info(&pdev->dev, |
| 2904 |
"Invalid MRRS override value %d", pcie_mrrs); |
| 2905 |
} |
| 2906 |
|
| 2907 |
/* Set PCIe completion timeout to 1-10ms */ |
| 2908 |
pcie_capability_clear_and_set_word(pdev, PCI_EXP_DEVCTL2, |
| 2909 |
PCI_EXP_DEVCTL2_COMP_TIMEOUT, 0x2); |
| 2910 |
|
| 2911 |
/* |
| 2912 |
* FIXUP: correct offsets of MSI-X tables in the MSI-X Capability Block |
| 2913 |
*/ |
| 2914 |
pci_write_config_dword(pdev, TSI721_PCIECFG_EPCTL, 0x01); |
| 2915 |
pci_write_config_dword(pdev, TSI721_PCIECFG_MSIXTBL, |
| 2916 |
TSI721_MSIXTBL_OFFSET); |
| 2917 |
pci_write_config_dword(pdev, TSI721_PCIECFG_MSIXPBA, |
| 2918 |
TSI721_MSIXPBA_OFFSET); |
| 2919 |
pci_write_config_dword(pdev, TSI721_PCIECFG_EPCTL, 0); |
| 2920 |
/* End of FIXUP */ |
| 2921 |
|
| 2922 |
tsi721_disable_ints(priv); |
| 2923 |
|
| 2924 |
tsi721_init_pc2sr_mapping(priv); |
| 2925 |
tsi721_init_sr2pc_mapping(priv); |
| 2926 |
|
| 2927 |
if (tsi721_bdma_maint_init(priv)) { |
| 2928 |
tsi_err(&pdev->dev, "BDMA initialization failed"); |
| 2929 |
err = -ENOMEM; |
| 2930 |
goto err_unmap_bars; |
| 2931 |
} |
| 2932 |
|
| 2933 |
err = tsi721_doorbell_init(priv); |
| 2934 |
if (err) |
| 2935 |
goto err_free_bdma; |
| 2936 |
|
| 2937 |
tsi721_port_write_init(priv); |
| 2938 |
|
| 2939 |
err = tsi721_messages_init(priv); |
| 2940 |
if (err) |
| 2941 |
goto err_free_consistent; |
| 2942 |
|
| 2943 |
err = tsi721_setup_mport(priv); |
| 2944 |
if (err) |
| 2945 |
goto err_free_consistent; |
| 2946 |
|
| 2947 |
pci_set_drvdata(pdev, priv); |
| 2948 |
tsi721_interrupts_init(priv); |
| 2949 |
|
| 2950 |
return 0; |
| 2951 |
|
| 2952 |
err_free_consistent: |
| 2953 |
tsi721_port_write_free(priv); |
| 2954 |
tsi721_doorbell_free(priv); |
| 2955 |
err_free_bdma: |
| 2956 |
tsi721_bdma_maint_free(priv); |
| 2957 |
err_unmap_bars: |
| 2958 |
if (priv->regs) |
| 2959 |
iounmap(priv->regs); |
| 2960 |
if (priv->odb_base) |
| 2961 |
iounmap(priv->odb_base); |
| 2962 |
err_free_res: |
| 2963 |
pci_release_regions(pdev); |
| 2964 |
err_disable_pdev: |
| 2965 |
pci_disable_device(pdev); |
| 2966 |
err_clean: |
| 2967 |
kfree(priv); |
| 2968 |
err_exit: |
| 2969 |
return err; |
| 2970 |
} |
| 2971 |
|
| 2972 |
static void tsi721_remove(struct pci_dev *pdev) |
| 2973 |
{ |
| 2974 |
struct tsi721_device *priv = pci_get_drvdata(pdev); |
| 2975 |
|
| 2976 |
tsi_debug(EXIT, &pdev->dev, "enter"); |
| 2977 |
|
| 2978 |
tsi721_disable_ints(priv); |
| 2979 |
tsi721_free_irq(priv); |
| 2980 |
flush_work(&priv->idb_work); |
| 2981 |
flush_work(&priv->pw_work); |
| 2982 |
rio_unregister_mport(&priv->mport); |
| 2983 |
|
| 2984 |
tsi721_unregister_dma(priv); |
| 2985 |
tsi721_bdma_maint_free(priv); |
| 2986 |
tsi721_doorbell_free(priv); |
| 2987 |
tsi721_port_write_free(priv); |
| 2988 |
tsi721_close_sr2pc_mapping(priv); |
| 2989 |
|
| 2990 |
if (priv->regs) |
| 2991 |
iounmap(priv->regs); |
| 2992 |
if (priv->odb_base) |
| 2993 |
iounmap(priv->odb_base); |
| 2994 |
#ifdef CONFIG_PCI_MSI |
| 2995 |
if (priv->flags & TSI721_USING_MSIX) |
| 2996 |
pci_disable_msix(priv->pdev); |
| 2997 |
else if (priv->flags & TSI721_USING_MSI) |
| 2998 |
pci_disable_msi(priv->pdev); |
| 2999 |
#endif |
| 3000 |
pci_release_regions(pdev); |
| 3001 |
pci_disable_device(pdev); |
| 3002 |
pci_set_drvdata(pdev, NULL); |
| 3003 |
kfree(priv); |
| 3004 |
tsi_debug(EXIT, &pdev->dev, "exit"); |
| 3005 |
} |
| 3006 |
|
| 3007 |
static void tsi721_shutdown(struct pci_dev *pdev) |
| 3008 |
{ |
| 3009 |
struct tsi721_device *priv = pci_get_drvdata(pdev); |
| 3010 |
|
| 3011 |
tsi_debug(EXIT, &pdev->dev, "enter"); |
| 3012 |
|
| 3013 |
tsi721_disable_ints(priv); |
| 3014 |
tsi721_dma_stop_all(priv); |
| 3015 |
pci_disable_device(pdev); |
| 3016 |
} |
| 3017 |
|
| 3018 |
static const struct pci_device_id tsi721_pci_tbl[] = { |
| 3019 |
{ PCI_DEVICE(PCI_VENDOR_ID_IDT, PCI_DEVICE_ID_TSI721) }, |
| 3020 |
{ 0, } /* terminate list */ |
| 3021 |
}; |
| 3022 |
|
| 3023 |
MODULE_DEVICE_TABLE(pci, tsi721_pci_tbl); |
| 3024 |
|
| 3025 |
static struct pci_driver tsi721_driver = { |
| 3026 |
.name = "tsi721", |
| 3027 |
.id_table = tsi721_pci_tbl, |
| 3028 |
.probe = tsi721_probe, |
| 3029 |
.remove = tsi721_remove, |
| 3030 |
.shutdown = tsi721_shutdown, |
| 3031 |
}; |
| 3032 |
|
| 3033 |
module_pci_driver(tsi721_driver); |
| 3034 |
|
| 3035 |
MODULE_DESCRIPTION("IDT Tsi721 PCIExpress-to-SRIO bridge driver"); |
| 3036 |
MODULE_AUTHOR("Integrated Device Technology, Inc."); |
| 3037 |
MODULE_LICENSE("GPL"); |