| 1 |
// SPDX-License-Identifier: GPL-2.0-or-later |
| 2 |
/* ZD1211 USB-WLAN driver for Linux |
| 3 |
* |
| 4 |
* Copyright (C) 2005-2007 Ulrich Kunitz <[email protected]> |
| 5 |
* Copyright (C) 2006-2007 Daniel Drake <[email protected]> |
| 6 |
*/ |
| 7 |
|
| 8 |
#include <linux/kernel.h> |
| 9 |
#include <linux/slab.h> |
| 10 |
|
| 11 |
#include "zd_rf.h" |
| 12 |
#include "zd_usb.h" |
| 13 |
#include "zd_chip.h" |
| 14 |
|
| 15 |
/* This RF programming code is based upon the code found in v2.16.0.0 of the |
| 16 |
* ZyDAS vendor driver. Unlike other RF's, Ubec publish full technical specs |
| 17 |
* for this RF on their website, so we're able to understand more than |
| 18 |
* usual as to what is going on. Thumbs up for Ubec for doing that. */ |
| 19 |
|
| 20 |
/* The 3-wire serial interface provides access to 8 write-only registers. |
| 21 |
* The data format is a 4 bit register address followed by a 20 bit value. */ |
| 22 |
#define UW2453_REGWRITE(reg, val) ((((reg) & 0xf) << 20) | ((val) & 0xfffff)) |
| 23 |
|
| 24 |
/* For channel tuning, we have to configure registers 1 (synthesizer), 2 (synth |
| 25 |
* fractional divide ratio) and 3 (VCO config). |
| 26 |
* |
| 27 |
* We configure the RF to produce an interrupt when the PLL is locked onto |
| 28 |
* the configured frequency. During initialization, we run through a variety |
| 29 |
* of different VCO configurations on channel 1 until we detect a PLL lock. |
| 30 |
* When this happens, we remember which VCO configuration produced the lock |
| 31 |
* and use it later. Actually, we use the configuration *after* the one that |
| 32 |
* produced the lock, which seems odd, but it works. |
| 33 |
* |
| 34 |
* If we do not see a PLL lock on any standard VCO config, we fall back on an |
| 35 |
* autocal configuration, which has a fixed (as opposed to per-channel) VCO |
| 36 |
* config and different synth values from the standard set (divide ratio |
| 37 |
* is still shared with the standard set). */ |
| 38 |
|
| 39 |
/* The per-channel synth values for all standard VCO configurations. These get |
| 40 |
* written to register 1. */ |
| 41 |
static const u8 uw2453_std_synth[] = { |
| 42 |
RF_CHANNEL( 1) = 0x47, |
| 43 |
RF_CHANNEL( 2) = 0x47, |
| 44 |
RF_CHANNEL( 3) = 0x67, |
| 45 |
RF_CHANNEL( 4) = 0x67, |
| 46 |
RF_CHANNEL( 5) = 0x67, |
| 47 |
RF_CHANNEL( 6) = 0x67, |
| 48 |
RF_CHANNEL( 7) = 0x57, |
| 49 |
RF_CHANNEL( 8) = 0x57, |
| 50 |
RF_CHANNEL( 9) = 0x57, |
| 51 |
RF_CHANNEL(10) = 0x57, |
| 52 |
RF_CHANNEL(11) = 0x77, |
| 53 |
RF_CHANNEL(12) = 0x77, |
| 54 |
RF_CHANNEL(13) = 0x77, |
| 55 |
RF_CHANNEL(14) = 0x4f, |
| 56 |
}; |
| 57 |
|
| 58 |
/* This table stores the synthesizer fractional divide ratio for *all* VCO |
| 59 |
* configurations (both standard and autocal). These get written to register 2. |
| 60 |
*/ |
| 61 |
static const u16 uw2453_synth_divide[] = { |
| 62 |
RF_CHANNEL( 1) = 0x999, |
| 63 |
RF_CHANNEL( 2) = 0x99b, |
| 64 |
RF_CHANNEL( 3) = 0x998, |
| 65 |
RF_CHANNEL( 4) = 0x99a, |
| 66 |
RF_CHANNEL( 5) = 0x999, |
| 67 |
RF_CHANNEL( 6) = 0x99b, |
| 68 |
RF_CHANNEL( 7) = 0x998, |
| 69 |
RF_CHANNEL( 8) = 0x99a, |
| 70 |
RF_CHANNEL( 9) = 0x999, |
| 71 |
RF_CHANNEL(10) = 0x99b, |
| 72 |
RF_CHANNEL(11) = 0x998, |
| 73 |
RF_CHANNEL(12) = 0x99a, |
| 74 |
RF_CHANNEL(13) = 0x999, |
| 75 |
RF_CHANNEL(14) = 0xccc, |
| 76 |
}; |
| 77 |
|
| 78 |
/* Here is the data for all the standard VCO configurations. We shrink our |
| 79 |
* table a little by observing that both channels in a consecutive pair share |
| 80 |
* the same value. We also observe that the high 4 bits ([0:3] in the specs) |
| 81 |
* are all 'Reserved' and are always set to 0x4 - we chop them off in the data |
| 82 |
* below. */ |
| 83 |
#define CHAN_TO_PAIRIDX(a) ((a - 1) / 2) |
| 84 |
#define RF_CHANPAIR(a,b) [CHAN_TO_PAIRIDX(a)] |
| 85 |
static const u16 uw2453_std_vco_cfg[][7] = { |
| 86 |
{ /* table 1 */ |
| 87 |
RF_CHANPAIR( 1, 2) = 0x664d, |
| 88 |
RF_CHANPAIR( 3, 4) = 0x604d, |
| 89 |
RF_CHANPAIR( 5, 6) = 0x6675, |
| 90 |
RF_CHANPAIR( 7, 8) = 0x6475, |
| 91 |
RF_CHANPAIR( 9, 10) = 0x6655, |
| 92 |
RF_CHANPAIR(11, 12) = 0x6455, |
| 93 |
RF_CHANPAIR(13, 14) = 0x6665, |
| 94 |
}, |
| 95 |
{ /* table 2 */ |
| 96 |
RF_CHANPAIR( 1, 2) = 0x666d, |
| 97 |
RF_CHANPAIR( 3, 4) = 0x606d, |
| 98 |
RF_CHANPAIR( 5, 6) = 0x664d, |
| 99 |
RF_CHANPAIR( 7, 8) = 0x644d, |
| 100 |
RF_CHANPAIR( 9, 10) = 0x6675, |
| 101 |
RF_CHANPAIR(11, 12) = 0x6475, |
| 102 |
RF_CHANPAIR(13, 14) = 0x6655, |
| 103 |
}, |
| 104 |
{ /* table 3 */ |
| 105 |
RF_CHANPAIR( 1, 2) = 0x665d, |
| 106 |
RF_CHANPAIR( 3, 4) = 0x605d, |
| 107 |
RF_CHANPAIR( 5, 6) = 0x666d, |
| 108 |
RF_CHANPAIR( 7, 8) = 0x646d, |
| 109 |
RF_CHANPAIR( 9, 10) = 0x664d, |
| 110 |
RF_CHANPAIR(11, 12) = 0x644d, |
| 111 |
RF_CHANPAIR(13, 14) = 0x6675, |
| 112 |
}, |
| 113 |
{ /* table 4 */ |
| 114 |
RF_CHANPAIR( 1, 2) = 0x667d, |
| 115 |
RF_CHANPAIR( 3, 4) = 0x607d, |
| 116 |
RF_CHANPAIR( 5, 6) = 0x665d, |
| 117 |
RF_CHANPAIR( 7, 8) = 0x645d, |
| 118 |
RF_CHANPAIR( 9, 10) = 0x666d, |
| 119 |
RF_CHANPAIR(11, 12) = 0x646d, |
| 120 |
RF_CHANPAIR(13, 14) = 0x664d, |
| 121 |
}, |
| 122 |
{ /* table 5 */ |
| 123 |
RF_CHANPAIR( 1, 2) = 0x6643, |
| 124 |
RF_CHANPAIR( 3, 4) = 0x6043, |
| 125 |
RF_CHANPAIR( 5, 6) = 0x667d, |
| 126 |
RF_CHANPAIR( 7, 8) = 0x647d, |
| 127 |
RF_CHANPAIR( 9, 10) = 0x665d, |
| 128 |
RF_CHANPAIR(11, 12) = 0x645d, |
| 129 |
RF_CHANPAIR(13, 14) = 0x666d, |
| 130 |
}, |
| 131 |
{ /* table 6 */ |
| 132 |
RF_CHANPAIR( 1, 2) = 0x6663, |
| 133 |
RF_CHANPAIR( 3, 4) = 0x6063, |
| 134 |
RF_CHANPAIR( 5, 6) = 0x6643, |
| 135 |
RF_CHANPAIR( 7, 8) = 0x6443, |
| 136 |
RF_CHANPAIR( 9, 10) = 0x667d, |
| 137 |
RF_CHANPAIR(11, 12) = 0x647d, |
| 138 |
RF_CHANPAIR(13, 14) = 0x665d, |
| 139 |
}, |
| 140 |
{ /* table 7 */ |
| 141 |
RF_CHANPAIR( 1, 2) = 0x6653, |
| 142 |
RF_CHANPAIR( 3, 4) = 0x6053, |
| 143 |
RF_CHANPAIR( 5, 6) = 0x6663, |
| 144 |
RF_CHANPAIR( 7, 8) = 0x6463, |
| 145 |
RF_CHANPAIR( 9, 10) = 0x6643, |
| 146 |
RF_CHANPAIR(11, 12) = 0x6443, |
| 147 |
RF_CHANPAIR(13, 14) = 0x667d, |
| 148 |
}, |
| 149 |
{ /* table 8 */ |
| 150 |
RF_CHANPAIR( 1, 2) = 0x6673, |
| 151 |
RF_CHANPAIR( 3, 4) = 0x6073, |
| 152 |
RF_CHANPAIR( 5, 6) = 0x6653, |
| 153 |
RF_CHANPAIR( 7, 8) = 0x6453, |
| 154 |
RF_CHANPAIR( 9, 10) = 0x6663, |
| 155 |
RF_CHANPAIR(11, 12) = 0x6463, |
| 156 |
RF_CHANPAIR(13, 14) = 0x6643, |
| 157 |
}, |
| 158 |
{ /* table 9 */ |
| 159 |
RF_CHANPAIR( 1, 2) = 0x664b, |
| 160 |
RF_CHANPAIR( 3, 4) = 0x604b, |
| 161 |
RF_CHANPAIR( 5, 6) = 0x6673, |
| 162 |
RF_CHANPAIR( 7, 8) = 0x6473, |
| 163 |
RF_CHANPAIR( 9, 10) = 0x6653, |
| 164 |
RF_CHANPAIR(11, 12) = 0x6453, |
| 165 |
RF_CHANPAIR(13, 14) = 0x6663, |
| 166 |
}, |
| 167 |
{ /* table 10 */ |
| 168 |
RF_CHANPAIR( 1, 2) = 0x666b, |
| 169 |
RF_CHANPAIR( 3, 4) = 0x606b, |
| 170 |
RF_CHANPAIR( 5, 6) = 0x664b, |
| 171 |
RF_CHANPAIR( 7, 8) = 0x644b, |
| 172 |
RF_CHANPAIR( 9, 10) = 0x6673, |
| 173 |
RF_CHANPAIR(11, 12) = 0x6473, |
| 174 |
RF_CHANPAIR(13, 14) = 0x6653, |
| 175 |
}, |
| 176 |
{ /* table 11 */ |
| 177 |
RF_CHANPAIR( 1, 2) = 0x665b, |
| 178 |
RF_CHANPAIR( 3, 4) = 0x605b, |
| 179 |
RF_CHANPAIR( 5, 6) = 0x666b, |
| 180 |
RF_CHANPAIR( 7, 8) = 0x646b, |
| 181 |
RF_CHANPAIR( 9, 10) = 0x664b, |
| 182 |
RF_CHANPAIR(11, 12) = 0x644b, |
| 183 |
RF_CHANPAIR(13, 14) = 0x6673, |
| 184 |
}, |
| 185 |
|
| 186 |
}; |
| 187 |
|
| 188 |
/* The per-channel synth values for autocal. These get written to register 1. */ |
| 189 |
static const u16 uw2453_autocal_synth[] = { |
| 190 |
RF_CHANNEL( 1) = 0x6847, |
| 191 |
RF_CHANNEL( 2) = 0x6847, |
| 192 |
RF_CHANNEL( 3) = 0x6867, |
| 193 |
RF_CHANNEL( 4) = 0x6867, |
| 194 |
RF_CHANNEL( 5) = 0x6867, |
| 195 |
RF_CHANNEL( 6) = 0x6867, |
| 196 |
RF_CHANNEL( 7) = 0x6857, |
| 197 |
RF_CHANNEL( 8) = 0x6857, |
| 198 |
RF_CHANNEL( 9) = 0x6857, |
| 199 |
RF_CHANNEL(10) = 0x6857, |
| 200 |
RF_CHANNEL(11) = 0x6877, |
| 201 |
RF_CHANNEL(12) = 0x6877, |
| 202 |
RF_CHANNEL(13) = 0x6877, |
| 203 |
RF_CHANNEL(14) = 0x684f, |
| 204 |
}; |
| 205 |
|
| 206 |
/* The VCO configuration for autocal (all channels) */ |
| 207 |
static const u16 UW2453_AUTOCAL_VCO_CFG = 0x6662; |
| 208 |
|
| 209 |
/* TX gain settings. The array index corresponds to the TX power integration |
| 210 |
* values found in the EEPROM. The values get written to register 7. */ |
| 211 |
static u32 uw2453_txgain[] = { |
| 212 |
[0x00] = 0x0e313, |
| 213 |
[0x01] = 0x0fb13, |
| 214 |
[0x02] = 0x0e093, |
| 215 |
[0x03] = 0x0f893, |
| 216 |
[0x04] = 0x0ea93, |
| 217 |
[0x05] = 0x1f093, |
| 218 |
[0x06] = 0x1f493, |
| 219 |
[0x07] = 0x1f693, |
| 220 |
[0x08] = 0x1f393, |
| 221 |
[0x09] = 0x1f35b, |
| 222 |
[0x0a] = 0x1e6db, |
| 223 |
[0x0b] = 0x1ff3f, |
| 224 |
[0x0c] = 0x1ffff, |
| 225 |
[0x0d] = 0x361d7, |
| 226 |
[0x0e] = 0x37fbf, |
| 227 |
[0x0f] = 0x3ff8b, |
| 228 |
[0x10] = 0x3ff33, |
| 229 |
[0x11] = 0x3fb3f, |
| 230 |
[0x12] = 0x3ffff, |
| 231 |
}; |
| 232 |
|
| 233 |
/* RF-specific structure */ |
| 234 |
struct uw2453_priv { |
| 235 |
/* index into synth/VCO config tables where PLL lock was found |
| 236 |
* -1 means autocal */ |
| 237 |
int config; |
| 238 |
}; |
| 239 |
|
| 240 |
#define UW2453_PRIV(rf) ((struct uw2453_priv *) (rf)->priv) |
| 241 |
|
| 242 |
static int uw2453_synth_set_channel(struct zd_chip *chip, int channel, |
| 243 |
bool autocal) |
| 244 |
{ |
| 245 |
int r; |
| 246 |
int idx = channel - 1; |
| 247 |
u32 val; |
| 248 |
|
| 249 |
if (autocal) |
| 250 |
val = UW2453_REGWRITE(1, uw2453_autocal_synth[idx]); |
| 251 |
else |
| 252 |
val = UW2453_REGWRITE(1, uw2453_std_synth[idx]); |
| 253 |
|
| 254 |
r = zd_rfwrite_locked(chip, val, RF_RV_BITS); |
| 255 |
if (r) |
| 256 |
return r; |
| 257 |
|
| 258 |
return zd_rfwrite_locked(chip, |
| 259 |
UW2453_REGWRITE(2, uw2453_synth_divide[idx]), RF_RV_BITS); |
| 260 |
} |
| 261 |
|
| 262 |
static int uw2453_write_vco_cfg(struct zd_chip *chip, u16 value) |
| 263 |
{ |
| 264 |
/* vendor driver always sets these upper bits even though the specs say |
| 265 |
* they are reserved */ |
| 266 |
u32 val = 0x40000 | value; |
| 267 |
return zd_rfwrite_locked(chip, UW2453_REGWRITE(3, val), RF_RV_BITS); |
| 268 |
} |
| 269 |
|
| 270 |
static int uw2453_init_mode(struct zd_chip *chip) |
| 271 |
{ |
| 272 |
static const u32 rv[] = { |
| 273 |
UW2453_REGWRITE(0, 0x25f98), /* enter IDLE mode */ |
| 274 |
UW2453_REGWRITE(0, 0x25f9a), /* enter CAL_VCO mode */ |
| 275 |
UW2453_REGWRITE(0, 0x25f94), /* enter RX/TX mode */ |
| 276 |
UW2453_REGWRITE(0, 0x27fd4), /* power down RSSI circuit */ |
| 277 |
}; |
| 278 |
|
| 279 |
return zd_rfwritev_locked(chip, rv, ARRAY_SIZE(rv), RF_RV_BITS); |
| 280 |
} |
| 281 |
|
| 282 |
static int uw2453_set_tx_gain_level(struct zd_chip *chip, int channel) |
| 283 |
{ |
| 284 |
u8 int_value = chip->pwr_int_values[channel - 1]; |
| 285 |
|
| 286 |
if (int_value >= ARRAY_SIZE(uw2453_txgain)) { |
| 287 |
dev_dbg_f(zd_chip_dev(chip), "can't configure TX gain for " |
| 288 |
"int value %x on channel %d\n", int_value, channel); |
| 289 |
return 0; |
| 290 |
} |
| 291 |
|
| 292 |
return zd_rfwrite_locked(chip, |
| 293 |
UW2453_REGWRITE(7, uw2453_txgain[int_value]), RF_RV_BITS); |
| 294 |
} |
| 295 |
|
| 296 |
static int uw2453_init_hw(struct zd_rf *rf) |
| 297 |
{ |
| 298 |
int i, r; |
| 299 |
int found_config = -1; |
| 300 |
u16 intr_status; |
| 301 |
struct zd_chip *chip = zd_rf_to_chip(rf); |
| 302 |
|
| 303 |
static const struct zd_ioreq16 ioreqs[] = { |
| 304 |
{ ZD_CR10, 0x89 }, { ZD_CR15, 0x20 }, |
| 305 |
{ ZD_CR17, 0x28 }, /* 6112 no change */ |
| 306 |
{ ZD_CR23, 0x38 }, { ZD_CR24, 0x20 }, { ZD_CR26, 0x93 }, |
| 307 |
{ ZD_CR27, 0x15 }, { ZD_CR28, 0x3e }, { ZD_CR29, 0x00 }, |
| 308 |
{ ZD_CR33, 0x28 }, { ZD_CR34, 0x30 }, |
| 309 |
{ ZD_CR35, 0x43 }, /* 6112 3e->43 */ |
| 310 |
{ ZD_CR41, 0x24 }, { ZD_CR44, 0x32 }, |
| 311 |
{ ZD_CR46, 0x92 }, /* 6112 96->92 */ |
| 312 |
{ ZD_CR47, 0x1e }, |
| 313 |
{ ZD_CR48, 0x04 }, /* 5602 Roger */ |
| 314 |
{ ZD_CR49, 0xfa }, { ZD_CR79, 0x58 }, { ZD_CR80, 0x30 }, |
| 315 |
{ ZD_CR81, 0x30 }, { ZD_CR87, 0x0a }, { ZD_CR89, 0x04 }, |
| 316 |
{ ZD_CR91, 0x00 }, { ZD_CR92, 0x0a }, { ZD_CR98, 0x8d }, |
| 317 |
{ ZD_CR99, 0x28 }, { ZD_CR100, 0x02 }, |
| 318 |
{ ZD_CR101, 0x09 }, /* 6112 13->1f 6220 1f->13 6407 13->9 */ |
| 319 |
{ ZD_CR102, 0x27 }, |
| 320 |
{ ZD_CR106, 0x1c }, /* 5d07 5112 1f->1c 6220 1c->1f |
| 321 |
* 6221 1f->1c |
| 322 |
*/ |
| 323 |
{ ZD_CR107, 0x1c }, /* 6220 1c->1a 5221 1a->1c */ |
| 324 |
{ ZD_CR109, 0x13 }, |
| 325 |
{ ZD_CR110, 0x1f }, /* 6112 13->1f 6221 1f->13 6407 13->0x09 */ |
| 326 |
{ ZD_CR111, 0x13 }, { ZD_CR112, 0x1f }, { ZD_CR113, 0x27 }, |
| 327 |
{ ZD_CR114, 0x23 }, /* 6221 27->23 */ |
| 328 |
{ ZD_CR115, 0x24 }, /* 6112 24->1c 6220 1c->24 */ |
| 329 |
{ ZD_CR116, 0x24 }, /* 6220 1c->24 */ |
| 330 |
{ ZD_CR117, 0xfa }, /* 6112 fa->f8 6220 f8->f4 6220 f4->fa */ |
| 331 |
{ ZD_CR118, 0xf0 }, /* 5d07 6112 f0->f2 6220 f2->f0 */ |
| 332 |
{ ZD_CR119, 0x1a }, /* 6112 1a->10 6220 10->14 6220 14->1a */ |
| 333 |
{ ZD_CR120, 0x4f }, |
| 334 |
{ ZD_CR121, 0x1f }, /* 6220 4f->1f */ |
| 335 |
{ ZD_CR122, 0xf0 }, { ZD_CR123, 0x57 }, { ZD_CR125, 0xad }, |
| 336 |
{ ZD_CR126, 0x6c }, { ZD_CR127, 0x03 }, |
| 337 |
{ ZD_CR128, 0x14 }, /* 6302 12->11 */ |
| 338 |
{ ZD_CR129, 0x12 }, /* 6301 10->0f */ |
| 339 |
{ ZD_CR130, 0x10 }, { ZD_CR137, 0x50 }, { ZD_CR138, 0xa8 }, |
| 340 |
{ ZD_CR144, 0xac }, { ZD_CR146, 0x20 }, { ZD_CR252, 0xff }, |
| 341 |
{ ZD_CR253, 0xff }, |
| 342 |
}; |
| 343 |
|
| 344 |
static const u32 rv[] = { |
| 345 |
UW2453_REGWRITE(4, 0x2b), /* configure receiver gain */ |
| 346 |
UW2453_REGWRITE(5, 0x19e4f), /* configure transmitter gain */ |
| 347 |
UW2453_REGWRITE(6, 0xf81ad), /* enable RX/TX filter tuning */ |
| 348 |
UW2453_REGWRITE(7, 0x3fffe), /* disable TX gain in test mode */ |
| 349 |
|
| 350 |
/* enter CAL_FIL mode, TX gain set by registers, RX gain set by pins, |
| 351 |
* RSSI circuit powered down, reduced RSSI range */ |
| 352 |
UW2453_REGWRITE(0, 0x25f9c), /* 5d01 cal_fil */ |
| 353 |
|
| 354 |
/* synthesizer configuration for channel 1 */ |
| 355 |
UW2453_REGWRITE(1, 0x47), |
| 356 |
UW2453_REGWRITE(2, 0x999), |
| 357 |
|
| 358 |
/* disable manual VCO band selection */ |
| 359 |
UW2453_REGWRITE(3, 0x7602), |
| 360 |
|
| 361 |
/* enable manual VCO band selection, configure current level */ |
| 362 |
UW2453_REGWRITE(3, 0x46063), |
| 363 |
}; |
| 364 |
|
| 365 |
r = zd_iowrite16a_locked(chip, ioreqs, ARRAY_SIZE(ioreqs)); |
| 366 |
if (r) |
| 367 |
return r; |
| 368 |
|
| 369 |
r = zd_rfwritev_locked(chip, rv, ARRAY_SIZE(rv), RF_RV_BITS); |
| 370 |
if (r) |
| 371 |
return r; |
| 372 |
|
| 373 |
r = uw2453_init_mode(chip); |
| 374 |
if (r) |
| 375 |
return r; |
| 376 |
|
| 377 |
/* Try all standard VCO configuration settings on channel 1 */ |
| 378 |
for (i = 0; i < ARRAY_SIZE(uw2453_std_vco_cfg) - 1; i++) { |
| 379 |
/* Configure synthesizer for channel 1 */ |
| 380 |
r = uw2453_synth_set_channel(chip, 1, false); |
| 381 |
if (r) |
| 382 |
return r; |
| 383 |
|
| 384 |
/* Write VCO config */ |
| 385 |
r = uw2453_write_vco_cfg(chip, uw2453_std_vco_cfg[i][0]); |
| 386 |
if (r) |
| 387 |
return r; |
| 388 |
|
| 389 |
/* ack interrupt event */ |
| 390 |
r = zd_iowrite16_locked(chip, 0x0f, UW2453_INTR_REG); |
| 391 |
if (r) |
| 392 |
return r; |
| 393 |
|
| 394 |
/* check interrupt status */ |
| 395 |
r = zd_ioread16_locked(chip, &intr_status, UW2453_INTR_REG); |
| 396 |
if (r) |
| 397 |
return r; |
| 398 |
|
| 399 |
if (!(intr_status & 0xf)) { |
| 400 |
dev_dbg_f(zd_chip_dev(chip), |
| 401 |
"PLL locked on configuration %d\n", i); |
| 402 |
found_config = i; |
| 403 |
break; |
| 404 |
} |
| 405 |
} |
| 406 |
|
| 407 |
if (found_config == -1) { |
| 408 |
/* autocal */ |
| 409 |
dev_dbg_f(zd_chip_dev(chip), |
| 410 |
"PLL did not lock, using autocal\n"); |
| 411 |
|
| 412 |
r = uw2453_synth_set_channel(chip, 1, true); |
| 413 |
if (r) |
| 414 |
return r; |
| 415 |
|
| 416 |
r = uw2453_write_vco_cfg(chip, UW2453_AUTOCAL_VCO_CFG); |
| 417 |
if (r) |
| 418 |
return r; |
| 419 |
} |
| 420 |
|
| 421 |
/* To match the vendor driver behaviour, we use the configuration after |
| 422 |
* the one that produced a lock. */ |
| 423 |
UW2453_PRIV(rf)->config = found_config + 1; |
| 424 |
|
| 425 |
return zd_iowrite16_locked(chip, 0x06, ZD_CR203); |
| 426 |
} |
| 427 |
|
| 428 |
static int uw2453_set_channel(struct zd_rf *rf, u8 channel) |
| 429 |
{ |
| 430 |
int r; |
| 431 |
u16 vco_cfg; |
| 432 |
int config = UW2453_PRIV(rf)->config; |
| 433 |
bool autocal = (config == -1); |
| 434 |
struct zd_chip *chip = zd_rf_to_chip(rf); |
| 435 |
|
| 436 |
static const struct zd_ioreq16 ioreqs[] = { |
| 437 |
{ ZD_CR80, 0x30 }, { ZD_CR81, 0x30 }, { ZD_CR79, 0x58 }, |
| 438 |
{ ZD_CR12, 0xf0 }, { ZD_CR77, 0x1b }, { ZD_CR78, 0x58 }, |
| 439 |
}; |
| 440 |
|
| 441 |
r = uw2453_synth_set_channel(chip, channel, autocal); |
| 442 |
if (r) |
| 443 |
return r; |
| 444 |
|
| 445 |
if (autocal) |
| 446 |
vco_cfg = UW2453_AUTOCAL_VCO_CFG; |
| 447 |
else |
| 448 |
vco_cfg = uw2453_std_vco_cfg[config][CHAN_TO_PAIRIDX(channel)]; |
| 449 |
|
| 450 |
r = uw2453_write_vco_cfg(chip, vco_cfg); |
| 451 |
if (r) |
| 452 |
return r; |
| 453 |
|
| 454 |
r = uw2453_init_mode(chip); |
| 455 |
if (r) |
| 456 |
return r; |
| 457 |
|
| 458 |
r = zd_iowrite16a_locked(chip, ioreqs, ARRAY_SIZE(ioreqs)); |
| 459 |
if (r) |
| 460 |
return r; |
| 461 |
|
| 462 |
r = uw2453_set_tx_gain_level(chip, channel); |
| 463 |
if (r) |
| 464 |
return r; |
| 465 |
|
| 466 |
return zd_iowrite16_locked(chip, 0x06, ZD_CR203); |
| 467 |
} |
| 468 |
|
| 469 |
static int uw2453_switch_radio_on(struct zd_rf *rf) |
| 470 |
{ |
| 471 |
int r; |
| 472 |
struct zd_chip *chip = zd_rf_to_chip(rf); |
| 473 |
struct zd_ioreq16 ioreqs[] = { |
| 474 |
{ ZD_CR11, 0x00 }, { ZD_CR251, 0x3f }, |
| 475 |
}; |
| 476 |
|
| 477 |
/* enter RXTX mode */ |
| 478 |
r = zd_rfwrite_locked(chip, UW2453_REGWRITE(0, 0x25f94), RF_RV_BITS); |
| 479 |
if (r) |
| 480 |
return r; |
| 481 |
|
| 482 |
if (zd_chip_is_zd1211b(chip)) |
| 483 |
ioreqs[1].value = 0x7f; |
| 484 |
|
| 485 |
return zd_iowrite16a_locked(chip, ioreqs, ARRAY_SIZE(ioreqs)); |
| 486 |
} |
| 487 |
|
| 488 |
static int uw2453_switch_radio_off(struct zd_rf *rf) |
| 489 |
{ |
| 490 |
int r; |
| 491 |
struct zd_chip *chip = zd_rf_to_chip(rf); |
| 492 |
static const struct zd_ioreq16 ioreqs[] = { |
| 493 |
{ ZD_CR11, 0x04 }, { ZD_CR251, 0x2f }, |
| 494 |
}; |
| 495 |
|
| 496 |
/* enter IDLE mode */ |
| 497 |
/* FIXME: shouldn't we go to SLEEP? sent email to zydas */ |
| 498 |
r = zd_rfwrite_locked(chip, UW2453_REGWRITE(0, 0x25f90), RF_RV_BITS); |
| 499 |
if (r) |
| 500 |
return r; |
| 501 |
|
| 502 |
return zd_iowrite16a_locked(chip, ioreqs, ARRAY_SIZE(ioreqs)); |
| 503 |
} |
| 504 |
|
| 505 |
static void uw2453_clear(struct zd_rf *rf) |
| 506 |
{ |
| 507 |
kfree(rf->priv); |
| 508 |
} |
| 509 |
|
| 510 |
int zd_rf_init_uw2453(struct zd_rf *rf) |
| 511 |
{ |
| 512 |
rf->init_hw = uw2453_init_hw; |
| 513 |
rf->set_channel = uw2453_set_channel; |
| 514 |
rf->switch_radio_on = uw2453_switch_radio_on; |
| 515 |
rf->switch_radio_off = uw2453_switch_radio_off; |
| 516 |
rf->patch_6m_band_edge = zd_rf_generic_patch_6m; |
| 517 |
rf->clear = uw2453_clear; |
| 518 |
/* we have our own TX integration code */ |
| 519 |
rf->update_channel_int = 0; |
| 520 |
|
| 521 |
rf->priv = kmalloc_obj(struct uw2453_priv); |
| 522 |
if (rf->priv == NULL) |
| 523 |
return -ENOMEM; |
| 524 |
|
| 525 |
return 0; |
| 526 |
} |
| 527 |
|