| 1 |
/* SPDX-License-Identifier: GPL-2.0-only */ |
| 2 |
/* |
| 3 |
* This file is part of wl12xx |
| 4 |
* |
| 5 |
* Copyright (C) 1998-2009 Texas Instruments. All rights reserved. |
| 6 |
* Copyright (C) 2009 Nokia Corporation |
| 7 |
* |
| 8 |
* Contact: Luciano Coelho <[email protected]> |
| 9 |
*/ |
| 10 |
|
| 11 |
#ifndef __REG_H__ |
| 12 |
#define __REG_H__ |
| 13 |
|
| 14 |
#include <linux/bitops.h> |
| 15 |
|
| 16 |
#define REGISTERS_BASE 0x00300000 |
| 17 |
#define DRPW_BASE 0x00310000 |
| 18 |
|
| 19 |
#define REGISTERS_DOWN_SIZE 0x00008800 |
| 20 |
#define REGISTERS_WORK_SIZE 0x0000b000 |
| 21 |
|
| 22 |
#define FW_STATUS_ADDR (0x14FC0 + 0xA000) |
| 23 |
|
| 24 |
/*=============================================== |
| 25 |
Host Software Reset - 32bit RW |
| 26 |
------------------------------------------ |
| 27 |
[31:1] Reserved |
| 28 |
0 SOFT_RESET Soft Reset - When this bit is set, |
| 29 |
it holds the Wlan hardware in a soft reset state. |
| 30 |
This reset disables all MAC and baseband processor |
| 31 |
clocks except the CardBus/PCI interface clock. |
| 32 |
It also initializes all MAC state machines except |
| 33 |
the host interface. It does not reload the |
| 34 |
contents of the EEPROM. When this bit is cleared |
| 35 |
(not self-clearing), the Wlan hardware |
| 36 |
exits the software reset state. |
| 37 |
===============================================*/ |
| 38 |
#define WL12XX_SLV_SOFT_RESET (REGISTERS_BASE + 0x0000) |
| 39 |
|
| 40 |
#define WL1271_SLV_REG_DATA (REGISTERS_BASE + 0x0008) |
| 41 |
#define WL1271_SLV_REG_ADATA (REGISTERS_BASE + 0x000c) |
| 42 |
#define WL1271_SLV_MEM_DATA (REGISTERS_BASE + 0x0018) |
| 43 |
|
| 44 |
#define WL12XX_REG_INTERRUPT_TRIG (REGISTERS_BASE + 0x0474) |
| 45 |
#define WL12XX_REG_INTERRUPT_TRIG_H (REGISTERS_BASE + 0x0478) |
| 46 |
|
| 47 |
/*============================================= |
| 48 |
Host Interrupt Mask Register - 32bit (RW) |
| 49 |
------------------------------------------ |
| 50 |
Setting a bit in this register masks the |
| 51 |
corresponding interrupt to the host. |
| 52 |
0 - RX0 - Rx first dubble buffer Data Interrupt |
| 53 |
1 - TXD - Tx Data Interrupt |
| 54 |
2 - TXXFR - Tx Transfer Interrupt |
| 55 |
3 - RX1 - Rx second dubble buffer Data Interrupt |
| 56 |
4 - RXXFR - Rx Transfer Interrupt |
| 57 |
5 - EVENT_A - Event Mailbox interrupt |
| 58 |
6 - EVENT_B - Event Mailbox interrupt |
| 59 |
7 - WNONHST - Wake On Host Interrupt |
| 60 |
8 - TRACE_A - Debug Trace interrupt |
| 61 |
9 - TRACE_B - Debug Trace interrupt |
| 62 |
10 - CDCMP - Command Complete Interrupt |
| 63 |
11 - |
| 64 |
12 - |
| 65 |
13 - |
| 66 |
14 - ICOMP - Initialization Complete Interrupt |
| 67 |
16 - SG SE - Soft Gemini - Sense enable interrupt |
| 68 |
17 - SG SD - Soft Gemini - Sense disable interrupt |
| 69 |
18 - - |
| 70 |
19 - - |
| 71 |
20 - - |
| 72 |
21- - |
| 73 |
Default: 0x0001 |
| 74 |
*==============================================*/ |
| 75 |
#define WL12XX_REG_INTERRUPT_MASK (REGISTERS_BASE + 0x04DC) |
| 76 |
|
| 77 |
/*============================================= |
| 78 |
Host Interrupt Mask Set 16bit, (Write only) |
| 79 |
------------------------------------------ |
| 80 |
Setting a bit in this register sets |
| 81 |
the corresponding bin in ACX_HINT_MASK register |
| 82 |
without effecting the mask |
| 83 |
state of other bits (0 = no effect). |
| 84 |
==============================================*/ |
| 85 |
#define ACX_REG_HINT_MASK_SET (REGISTERS_BASE + 0x04E0) |
| 86 |
|
| 87 |
/*============================================= |
| 88 |
Host Interrupt Mask Clear 16bit,(Write only) |
| 89 |
------------------------------------------ |
| 90 |
Setting a bit in this register clears |
| 91 |
the corresponding bin in ACX_HINT_MASK register |
| 92 |
without effecting the mask |
| 93 |
state of other bits (0 = no effect). |
| 94 |
=============================================*/ |
| 95 |
#define ACX_REG_HINT_MASK_CLR (REGISTERS_BASE + 0x04E4) |
| 96 |
|
| 97 |
/*============================================= |
| 98 |
Host Interrupt Status Nondestructive Read |
| 99 |
16bit,(Read only) |
| 100 |
------------------------------------------ |
| 101 |
The host can read this register to determine |
| 102 |
which interrupts are active. |
| 103 |
Reading this register doesn't |
| 104 |
effect its content. |
| 105 |
=============================================*/ |
| 106 |
#define WL12XX_REG_INTERRUPT_NO_CLEAR (REGISTERS_BASE + 0x04E8) |
| 107 |
|
| 108 |
/*============================================= |
| 109 |
Host Interrupt Status Clear on Read Register |
| 110 |
16bit,(Read only) |
| 111 |
------------------------------------------ |
| 112 |
The host can read this register to determine |
| 113 |
which interrupts are active. |
| 114 |
Reading this register clears it, |
| 115 |
thus making all interrupts inactive. |
| 116 |
==============================================*/ |
| 117 |
#define ACX_REG_INTERRUPT_CLEAR (REGISTERS_BASE + 0x04F8) |
| 118 |
|
| 119 |
/*============================================= |
| 120 |
Host Interrupt Acknowledge Register |
| 121 |
16bit,(Write only) |
| 122 |
------------------------------------------ |
| 123 |
The host can set individual bits in this |
| 124 |
register to clear (acknowledge) the corresp. |
| 125 |
interrupt status bits in the HINT_STS_CLR and |
| 126 |
HINT_STS_ND registers, thus making the |
| 127 |
assotiated interrupt inactive. (0-no effect) |
| 128 |
==============================================*/ |
| 129 |
#define WL12XX_REG_INTERRUPT_ACK (REGISTERS_BASE + 0x04F0) |
| 130 |
|
| 131 |
#define WL12XX_REG_RX_DRIVER_COUNTER (REGISTERS_BASE + 0x0538) |
| 132 |
|
| 133 |
/* Device Configuration registers*/ |
| 134 |
#define SOR_CFG (REGISTERS_BASE + 0x0800) |
| 135 |
|
| 136 |
/* Embedded ARM CPU Control */ |
| 137 |
|
| 138 |
/*=============================================== |
| 139 |
Halt eCPU - 32bit RW |
| 140 |
------------------------------------------ |
| 141 |
0 HALT_ECPU Halt Embedded CPU - This bit is the |
| 142 |
complement of bit 1 (MDATA2) in the SOR_CFG register. |
| 143 |
During a hardware reset, this bit holds |
| 144 |
the inverse of MDATA2. |
| 145 |
When downloading firmware from the host, |
| 146 |
set this bit (pull down MDATA2). |
| 147 |
The host clears this bit after downloading the firmware into |
| 148 |
zero-wait-state SSRAM. |
| 149 |
When loading firmware from Flash, clear this bit (pull up MDATA2) |
| 150 |
so that the eCPU can run the bootloader code in Flash |
| 151 |
HALT_ECPU eCPU State |
| 152 |
-------------------- |
| 153 |
1 halt eCPU |
| 154 |
0 enable eCPU |
| 155 |
===============================================*/ |
| 156 |
#define WL12XX_REG_ECPU_CONTROL (REGISTERS_BASE + 0x0804) |
| 157 |
|
| 158 |
#define WL12XX_HI_CFG (REGISTERS_BASE + 0x0808) |
| 159 |
|
| 160 |
/*=============================================== |
| 161 |
EEPROM Burst Read Start - 32bit RW |
| 162 |
------------------------------------------ |
| 163 |
[31:1] Reserved |
| 164 |
0 ACX_EE_START - EEPROM Burst Read Start 0 |
| 165 |
Setting this bit starts a burst read from |
| 166 |
the external EEPROM. |
| 167 |
If this bit is set (after reset) before an EEPROM read/write, |
| 168 |
the burst read starts at EEPROM address 0. |
| 169 |
Otherwise, it starts at the address |
| 170 |
following the address of the previous access. |
| 171 |
TheWlan hardware clears this bit automatically. |
| 172 |
|
| 173 |
Default: 0x00000000 |
| 174 |
*================================================*/ |
| 175 |
#define ACX_REG_EE_START (REGISTERS_BASE + 0x080C) |
| 176 |
|
| 177 |
#define WL12XX_OCP_POR_CTR (REGISTERS_BASE + 0x09B4) |
| 178 |
#define WL12XX_OCP_DATA_WRITE (REGISTERS_BASE + 0x09B8) |
| 179 |
#define WL12XX_OCP_DATA_READ (REGISTERS_BASE + 0x09BC) |
| 180 |
#define WL12XX_OCP_CMD (REGISTERS_BASE + 0x09C0) |
| 181 |
|
| 182 |
#define WL12XX_HOST_WR_ACCESS (REGISTERS_BASE + 0x09F8) |
| 183 |
|
| 184 |
#define WL12XX_CHIP_ID_B (REGISTERS_BASE + 0x5674) |
| 185 |
|
| 186 |
#define WL12XX_ENABLE (REGISTERS_BASE + 0x5450) |
| 187 |
|
| 188 |
/* Power Management registers */ |
| 189 |
#define WL12XX_ELP_CFG_MODE (REGISTERS_BASE + 0x5804) |
| 190 |
#define WL12XX_ELP_CMD (REGISTERS_BASE + 0x5808) |
| 191 |
#define WL12XX_PLL_CAL_TIME (REGISTERS_BASE + 0x5810) |
| 192 |
#define WL12XX_CLK_REQ_TIME (REGISTERS_BASE + 0x5814) |
| 193 |
#define WL12XX_CLK_BUF_TIME (REGISTERS_BASE + 0x5818) |
| 194 |
|
| 195 |
#define WL12XX_CFG_PLL_SYNC_CNT (REGISTERS_BASE + 0x5820) |
| 196 |
|
| 197 |
/* Scratch Pad registers*/ |
| 198 |
#define WL12XX_SCR_PAD0 (REGISTERS_BASE + 0x5608) |
| 199 |
#define WL12XX_SCR_PAD1 (REGISTERS_BASE + 0x560C) |
| 200 |
#define WL12XX_SCR_PAD2 (REGISTERS_BASE + 0x5610) |
| 201 |
#define WL12XX_SCR_PAD3 (REGISTERS_BASE + 0x5614) |
| 202 |
#define WL12XX_SCR_PAD4 (REGISTERS_BASE + 0x5618) |
| 203 |
#define WL12XX_SCR_PAD4_SET (REGISTERS_BASE + 0x561C) |
| 204 |
#define WL12XX_SCR_PAD4_CLR (REGISTERS_BASE + 0x5620) |
| 205 |
#define WL12XX_SCR_PAD5 (REGISTERS_BASE + 0x5624) |
| 206 |
#define WL12XX_SCR_PAD5_SET (REGISTERS_BASE + 0x5628) |
| 207 |
#define WL12XX_SCR_PAD5_CLR (REGISTERS_BASE + 0x562C) |
| 208 |
#define WL12XX_SCR_PAD6 (REGISTERS_BASE + 0x5630) |
| 209 |
#define WL12XX_SCR_PAD7 (REGISTERS_BASE + 0x5634) |
| 210 |
#define WL12XX_SCR_PAD8 (REGISTERS_BASE + 0x5638) |
| 211 |
#define WL12XX_SCR_PAD9 (REGISTERS_BASE + 0x563C) |
| 212 |
|
| 213 |
/* Spare registers*/ |
| 214 |
#define WL12XX_SPARE_A1 (REGISTERS_BASE + 0x0994) |
| 215 |
#define WL12XX_SPARE_A2 (REGISTERS_BASE + 0x0998) |
| 216 |
#define WL12XX_SPARE_A3 (REGISTERS_BASE + 0x099C) |
| 217 |
#define WL12XX_SPARE_A4 (REGISTERS_BASE + 0x09A0) |
| 218 |
#define WL12XX_SPARE_A5 (REGISTERS_BASE + 0x09A4) |
| 219 |
#define WL12XX_SPARE_A6 (REGISTERS_BASE + 0x09A8) |
| 220 |
#define WL12XX_SPARE_A7 (REGISTERS_BASE + 0x09AC) |
| 221 |
#define WL12XX_SPARE_A8 (REGISTERS_BASE + 0x09B0) |
| 222 |
#define WL12XX_SPARE_B1 (REGISTERS_BASE + 0x5420) |
| 223 |
#define WL12XX_SPARE_B2 (REGISTERS_BASE + 0x5424) |
| 224 |
#define WL12XX_SPARE_B3 (REGISTERS_BASE + 0x5428) |
| 225 |
#define WL12XX_SPARE_B4 (REGISTERS_BASE + 0x542C) |
| 226 |
#define WL12XX_SPARE_B5 (REGISTERS_BASE + 0x5430) |
| 227 |
#define WL12XX_SPARE_B6 (REGISTERS_BASE + 0x5434) |
| 228 |
#define WL12XX_SPARE_B7 (REGISTERS_BASE + 0x5438) |
| 229 |
#define WL12XX_SPARE_B8 (REGISTERS_BASE + 0x543C) |
| 230 |
|
| 231 |
#define WL12XX_PLL_PARAMETERS (REGISTERS_BASE + 0x6040) |
| 232 |
#define WL12XX_WU_COUNTER_PAUSE (REGISTERS_BASE + 0x6008) |
| 233 |
#define WL12XX_WELP_ARM_COMMAND (REGISTERS_BASE + 0x6100) |
| 234 |
#define WL12XX_DRPW_SCRATCH_START (DRPW_BASE + 0x002C) |
| 235 |
|
| 236 |
#define WL12XX_CMD_MBOX_ADDRESS 0x407B4 |
| 237 |
|
| 238 |
#define ACX_REG_EEPROM_START_BIT BIT(1) |
| 239 |
|
| 240 |
/* Command/Information Mailbox Pointers */ |
| 241 |
|
| 242 |
/*=============================================== |
| 243 |
Command Mailbox Pointer - 32bit RW |
| 244 |
------------------------------------------ |
| 245 |
This register holds the start address of |
| 246 |
the command mailbox located in the Wlan hardware memory. |
| 247 |
The host must read this pointer after a reset to |
| 248 |
find the location of the command mailbox. |
| 249 |
The Wlan hardware initializes the command mailbox |
| 250 |
pointer with the default address of the command mailbox. |
| 251 |
The command mailbox pointer is not valid until after |
| 252 |
the host receives the Init Complete interrupt from |
| 253 |
the Wlan hardware. |
| 254 |
===============================================*/ |
| 255 |
#define WL12XX_REG_COMMAND_MAILBOX_PTR (WL12XX_SCR_PAD0) |
| 256 |
|
| 257 |
/*=============================================== |
| 258 |
Information Mailbox Pointer - 32bit RW |
| 259 |
------------------------------------------ |
| 260 |
This register holds the start address of |
| 261 |
the information mailbox located in the Wlan hardware memory. |
| 262 |
The host must read this pointer after a reset to find |
| 263 |
the location of the information mailbox. |
| 264 |
The Wlan hardware initializes the information mailbox pointer |
| 265 |
with the default address of the information mailbox. |
| 266 |
The information mailbox pointer is not valid |
| 267 |
until after the host receives the Init Complete interrupt from |
| 268 |
the Wlan hardware. |
| 269 |
===============================================*/ |
| 270 |
#define WL12XX_REG_EVENT_MAILBOX_PTR (WL12XX_SCR_PAD1) |
| 271 |
|
| 272 |
/*=============================================== |
| 273 |
EEPROM Read/Write Request 32bit RW |
| 274 |
------------------------------------------ |
| 275 |
1 EE_READ - EEPROM Read Request 1 - Setting this bit |
| 276 |
loads a single byte of data into the EE_DATA |
| 277 |
register from the EEPROM location specified in |
| 278 |
the EE_ADDR register. |
| 279 |
The Wlan hardware clears this bit automatically. |
| 280 |
EE_DATA is valid when this bit is cleared. |
| 281 |
|
| 282 |
0 EE_WRITE - EEPROM Write Request - Setting this bit |
| 283 |
writes a single byte of data from the EE_DATA register into the |
| 284 |
EEPROM location specified in the EE_ADDR register. |
| 285 |
The Wlan hardware clears this bit automatically. |
| 286 |
*===============================================*/ |
| 287 |
#define ACX_EE_CTL_REG EE_CTL |
| 288 |
#define EE_WRITE 0x00000001ul |
| 289 |
#define EE_READ 0x00000002ul |
| 290 |
|
| 291 |
/*=============================================== |
| 292 |
EEPROM Address - 32bit RW |
| 293 |
------------------------------------------ |
| 294 |
This register specifies the address |
| 295 |
within the EEPROM from/to which to read/write data. |
| 296 |
===============================================*/ |
| 297 |
#define ACX_EE_ADDR_REG EE_ADDR |
| 298 |
|
| 299 |
/*=============================================== |
| 300 |
EEPROM Data - 32bit RW |
| 301 |
------------------------------------------ |
| 302 |
This register either holds the read 8 bits of |
| 303 |
data from the EEPROM or the write data |
| 304 |
to be written to the EEPROM. |
| 305 |
===============================================*/ |
| 306 |
#define ACX_EE_DATA_REG EE_DATA |
| 307 |
|
| 308 |
/*=============================================== |
| 309 |
EEPROM Base Address - 32bit RW |
| 310 |
------------------------------------------ |
| 311 |
This register holds the upper nine bits |
| 312 |
[23:15] of the 24-bit Wlan hardware memory |
| 313 |
address for burst reads from EEPROM accesses. |
| 314 |
The EEPROM provides the lower 15 bits of this address. |
| 315 |
The MSB of the address from the EEPROM is ignored. |
| 316 |
===============================================*/ |
| 317 |
#define ACX_EE_CFG EE_CFG |
| 318 |
|
| 319 |
/*=============================================== |
| 320 |
GPIO Output Values -32bit, RW |
| 321 |
------------------------------------------ |
| 322 |
[31:16] Reserved |
| 323 |
[15: 0] Specify the output values (at the output driver inputs) for |
| 324 |
GPIO[15:0], respectively. |
| 325 |
===============================================*/ |
| 326 |
#define ACX_GPIO_OUT_REG GPIO_OUT |
| 327 |
#define ACX_MAX_GPIO_LINES 15 |
| 328 |
|
| 329 |
/*=============================================== |
| 330 |
Contention window -32bit, RW |
| 331 |
------------------------------------------ |
| 332 |
[31:26] Reserved |
| 333 |
[25:16] Max (0x3ff) |
| 334 |
[15:07] Reserved |
| 335 |
[06:00] Current contention window value - default is 0x1F |
| 336 |
===============================================*/ |
| 337 |
#define ACX_CONT_WIND_CFG_REG CONT_WIND_CFG |
| 338 |
#define ACX_CONT_WIND_MIN_MASK 0x0000007f |
| 339 |
#define ACX_CONT_WIND_MAX 0x03ff0000 |
| 340 |
|
| 341 |
#define REF_FREQ_19_2 0 |
| 342 |
#define REF_FREQ_26_0 1 |
| 343 |
#define REF_FREQ_38_4 2 |
| 344 |
#define REF_FREQ_40_0 3 |
| 345 |
#define REF_FREQ_33_6 4 |
| 346 |
#define REF_FREQ_NUM 5 |
| 347 |
|
| 348 |
#define LUT_PARAM_INTEGER_DIVIDER 0 |
| 349 |
#define LUT_PARAM_FRACTIONAL_DIVIDER 1 |
| 350 |
#define LUT_PARAM_ATTN_BB 2 |
| 351 |
#define LUT_PARAM_ALPHA_BB 3 |
| 352 |
#define LUT_PARAM_STOP_TIME_BB 4 |
| 353 |
#define LUT_PARAM_BB_PLL_LOOP_FILTER 5 |
| 354 |
#define LUT_PARAM_NUM 6 |
| 355 |
|
| 356 |
#define WL12XX_EEPROMLESS_IND (WL12XX_SCR_PAD4) |
| 357 |
#define USE_EEPROM 0 |
| 358 |
#define NVS_DATA_BUNDARY_ALIGNMENT 4 |
| 359 |
|
| 360 |
/* Firmware image header size */ |
| 361 |
#define FW_HDR_SIZE 8 |
| 362 |
|
| 363 |
/****************************************************************************** |
| 364 |
|
| 365 |
CHANNELS, BAND & REG DOMAINS definitions |
| 366 |
|
| 367 |
******************************************************************************/ |
| 368 |
|
| 369 |
#define SHORT_PREAMBLE_BIT BIT(0) /* CCK or Barker depending on the rate */ |
| 370 |
#define OFDM_RATE_BIT BIT(6) |
| 371 |
#define PBCC_RATE_BIT BIT(7) |
| 372 |
|
| 373 |
enum { |
| 374 |
CCK_LONG = 0, |
| 375 |
CCK_SHORT = SHORT_PREAMBLE_BIT, |
| 376 |
PBCC_LONG = PBCC_RATE_BIT, |
| 377 |
PBCC_SHORT = PBCC_RATE_BIT | SHORT_PREAMBLE_BIT, |
| 378 |
OFDM = OFDM_RATE_BIT |
| 379 |
}; |
| 380 |
|
| 381 |
/****************************************************************************** |
| 382 |
|
| 383 |
Transmit-Descriptor RATE-SET field definitions... |
| 384 |
|
| 385 |
Define a new "Rate-Set" for TX path that incorporates the |
| 386 |
Rate & Modulation info into a single 16-bit field. |
| 387 |
|
| 388 |
TxdRateSet_t: |
| 389 |
b15 - Indicates Preamble type (1=SHORT, 0=LONG). |
| 390 |
Notes: |
| 391 |
Must be LONG (0) for 1Mbps rate. |
| 392 |
Does not apply (set to 0) for RevG-OFDM rates. |
| 393 |
b14 - Indicates PBCC encoding (1=PBCC, 0=not). |
| 394 |
Notes: |
| 395 |
Does not apply (set to 0) for rates 1 and 2 Mbps. |
| 396 |
Does not apply (set to 0) for RevG-OFDM rates. |
| 397 |
b13 - Unused (set to 0). |
| 398 |
b12-b0 - Supported Rate indicator bits as defined below. |
| 399 |
|
| 400 |
******************************************************************************/ |
| 401 |
|
| 402 |
#define OCP_CMD_LOOP 32 |
| 403 |
#define OCP_CMD_WRITE 0x1 |
| 404 |
#define OCP_CMD_READ 0x2 |
| 405 |
#define OCP_READY_MASK BIT(18) |
| 406 |
#define OCP_STATUS_MASK (BIT(16) | BIT(17)) |
| 407 |
#define OCP_STATUS_NO_RESP 0x00000 |
| 408 |
#define OCP_STATUS_OK 0x10000 |
| 409 |
#define OCP_STATUS_REQ_FAILED 0x20000 |
| 410 |
#define OCP_STATUS_RESP_ERROR 0x30000 |
| 411 |
|
| 412 |
#define OCP_REG_POLARITY 0x0064 |
| 413 |
#define OCP_REG_CLK_TYPE 0x0448 |
| 414 |
#define OCP_REG_CLK_POLARITY 0x0cb2 |
| 415 |
#define OCP_REG_CLK_PULL 0x0cb4 |
| 416 |
|
| 417 |
#define POLARITY_LOW BIT(1) |
| 418 |
#define NO_PULL (BIT(14) | BIT(15)) |
| 419 |
|
| 420 |
#define FREF_CLK_TYPE_BITS 0xfffffe7f |
| 421 |
#define CLK_REQ_PRCM 0x100 |
| 422 |
#define FREF_CLK_POLARITY_BITS 0xfffff8ff |
| 423 |
#define CLK_REQ_OUTN_SEL 0x700 |
| 424 |
|
| 425 |
#define WU_COUNTER_PAUSE_VAL 0x3FF |
| 426 |
|
| 427 |
/* PLL configuration algorithm for wl128x */ |
| 428 |
#define SYS_CLK_CFG_REG 0x2200 |
| 429 |
/* Bit[0] - 0-TCXO, 1-FREF */ |
| 430 |
#define MCS_PLL_CLK_SEL_FREF BIT(0) |
| 431 |
/* Bit[3:2] - 01-TCXO, 10-FREF */ |
| 432 |
#define WL_CLK_REQ_TYPE_FREF BIT(3) |
| 433 |
#define WL_CLK_REQ_TYPE_PG2 (BIT(3) | BIT(2)) |
| 434 |
/* Bit[4] - 0-TCXO, 1-FREF */ |
| 435 |
#define PRCM_CM_EN_MUX_WLAN_FREF BIT(4) |
| 436 |
|
| 437 |
#define TCXO_ILOAD_INT_REG 0x2264 |
| 438 |
#define TCXO_CLK_DETECT_REG 0x2266 |
| 439 |
|
| 440 |
#define TCXO_DET_FAILED BIT(4) |
| 441 |
|
| 442 |
#define FREF_ILOAD_INT_REG 0x2084 |
| 443 |
#define FREF_CLK_DETECT_REG 0x2086 |
| 444 |
#define FREF_CLK_DETECT_FAIL BIT(4) |
| 445 |
|
| 446 |
/* Use this reg for masking during driver access */ |
| 447 |
#define WL_SPARE_REG 0x2320 |
| 448 |
#define WL_SPARE_VAL BIT(2) |
| 449 |
/* Bit[6:5:3] - mask wl write SYS_CLK_CFG[8:5:2:4] */ |
| 450 |
#define WL_SPARE_MASK_8526 (BIT(6) | BIT(5) | BIT(3)) |
| 451 |
|
| 452 |
#define PLL_LOCK_COUNTERS_REG 0xD8C |
| 453 |
#define PLL_LOCK_COUNTERS_COEX 0x0F |
| 454 |
#define PLL_LOCK_COUNTERS_MCS 0xF0 |
| 455 |
#define MCS_PLL_OVERRIDE_REG 0xD90 |
| 456 |
#define MCS_PLL_CONFIG_REG 0xD92 |
| 457 |
#define MCS_SEL_IN_FREQ_MASK 0x0070 |
| 458 |
#define MCS_SEL_IN_FREQ_SHIFT 4 |
| 459 |
#define MCS_PLL_CONFIG_REG_VAL 0x73 |
| 460 |
#define MCS_PLL_ENABLE_HP (BIT(0) | BIT(1)) |
| 461 |
|
| 462 |
#define MCS_PLL_M_REG 0xD94 |
| 463 |
#define MCS_PLL_N_REG 0xD96 |
| 464 |
#define MCS_PLL_M_REG_VAL 0xC8 |
| 465 |
#define MCS_PLL_N_REG_VAL 0x07 |
| 466 |
|
| 467 |
#define SDIO_IO_DS 0xd14 |
| 468 |
|
| 469 |
/* SDIO/wSPI DS configuration values */ |
| 470 |
enum { |
| 471 |
HCI_IO_DS_8MA = 0, |
| 472 |
HCI_IO_DS_4MA = 1, /* default */ |
| 473 |
HCI_IO_DS_6MA = 2, |
| 474 |
HCI_IO_DS_2MA = 3, |
| 475 |
}; |
| 476 |
|
| 477 |
/* end PLL configuration algorithm for wl128x */ |
| 478 |
|
| 479 |
/* |
| 480 |
* Host Command Interrupt. Setting this bit masks |
| 481 |
* the interrupt that the host issues to inform |
| 482 |
* the FW that it has sent a command |
| 483 |
* to the Wlan hardware Command Mailbox. |
| 484 |
*/ |
| 485 |
#define WL12XX_INTR_TRIG_CMD BIT(0) |
| 486 |
|
| 487 |
/* |
| 488 |
* Host Event Acknowlegde Interrupt. The host |
| 489 |
* sets this bit to acknowledge that it received |
| 490 |
* the unsolicited information from the event |
| 491 |
* mailbox. |
| 492 |
*/ |
| 493 |
#define WL12XX_INTR_TRIG_EVENT_ACK BIT(1) |
| 494 |
|
| 495 |
/*=============================================== |
| 496 |
HI_CFG Interface Configuration Register Values |
| 497 |
------------------------------------------ |
| 498 |
===============================================*/ |
| 499 |
#define HI_CFG_UART_ENABLE 0x00000004 |
| 500 |
#define HI_CFG_RST232_ENABLE 0x00000008 |
| 501 |
#define HI_CFG_CLOCK_REQ_SELECT 0x00000010 |
| 502 |
#define HI_CFG_HOST_INT_ENABLE 0x00000020 |
| 503 |
#define HI_CFG_VLYNQ_OUTPUT_ENABLE 0x00000040 |
| 504 |
#define HI_CFG_HOST_INT_ACTIVE_LOW 0x00000080 |
| 505 |
#define HI_CFG_UART_TX_OUT_GPIO_15 0x00000100 |
| 506 |
#define HI_CFG_UART_TX_OUT_GPIO_14 0x00000200 |
| 507 |
#define HI_CFG_UART_TX_OUT_GPIO_7 0x00000400 |
| 508 |
|
| 509 |
#define HI_CFG_DEF_VAL \ |
| 510 |
(HI_CFG_UART_ENABLE | \ |
| 511 |
HI_CFG_RST232_ENABLE | \ |
| 512 |
HI_CFG_CLOCK_REQ_SELECT | \ |
| 513 |
HI_CFG_HOST_INT_ENABLE) |
| 514 |
|
| 515 |
#define WL127X_REG_FUSE_DATA_2_1 0x050a |
| 516 |
#define WL128X_REG_FUSE_DATA_2_1 0x2152 |
| 517 |
#define PG_VER_MASK 0x3c |
| 518 |
#define PG_VER_OFFSET 2 |
| 519 |
|
| 520 |
#define WL127X_PG_MAJOR_VER_MASK 0x3 |
| 521 |
#define WL127X_PG_MAJOR_VER_OFFSET 0x0 |
| 522 |
#define WL127X_PG_MINOR_VER_MASK 0xc |
| 523 |
#define WL127X_PG_MINOR_VER_OFFSET 0x2 |
| 524 |
|
| 525 |
#define WL128X_PG_MAJOR_VER_MASK 0xc |
| 526 |
#define WL128X_PG_MAJOR_VER_OFFSET 0x2 |
| 527 |
#define WL128X_PG_MINOR_VER_MASK 0x3 |
| 528 |
#define WL128X_PG_MINOR_VER_OFFSET 0x0 |
| 529 |
|
| 530 |
#define WL127X_PG_GET_MAJOR(pg_ver) ((pg_ver & WL127X_PG_MAJOR_VER_MASK) >> \ |
| 531 |
WL127X_PG_MAJOR_VER_OFFSET) |
| 532 |
#define WL127X_PG_GET_MINOR(pg_ver) ((pg_ver & WL127X_PG_MINOR_VER_MASK) >> \ |
| 533 |
WL127X_PG_MINOR_VER_OFFSET) |
| 534 |
#define WL128X_PG_GET_MAJOR(pg_ver) ((pg_ver & WL128X_PG_MAJOR_VER_MASK) >> \ |
| 535 |
WL128X_PG_MAJOR_VER_OFFSET) |
| 536 |
#define WL128X_PG_GET_MINOR(pg_ver) ((pg_ver & WL128X_PG_MINOR_VER_MASK) >> \ |
| 537 |
WL128X_PG_MINOR_VER_OFFSET) |
| 538 |
|
| 539 |
#define WL12XX_REG_FUSE_BD_ADDR_1 0x00310eb4 |
| 540 |
#define WL12XX_REG_FUSE_BD_ADDR_2 0x00310eb8 |
| 541 |
|
| 542 |
#endif |