| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* SPI interface. |
| 4 |
* |
| 5 |
* Copyright (c) 2017-2020, Silicon Laboratories, Inc. |
| 6 |
* Copyright (c) 2011, Sagrad Inc. |
| 7 |
* Copyright (c) 2010, ST-Ericsson |
| 8 |
*/ |
| 9 |
#include <linux/module.h> |
| 10 |
#include <linux/delay.h> |
| 11 |
#include <linux/gpio/consumer.h> |
| 12 |
#include <linux/spi/spi.h> |
| 13 |
#include <linux/interrupt.h> |
| 14 |
#include <linux/irq.h> |
| 15 |
#include <linux/of.h> |
| 16 |
#include <linux/pm.h> |
| 17 |
|
| 18 |
#include "bus.h" |
| 19 |
#include "wfx.h" |
| 20 |
#include "hwio.h" |
| 21 |
#include "main.h" |
| 22 |
#include "bh.h" |
| 23 |
|
| 24 |
#define SET_WRITE 0x7FFF /* usage: and operation */ |
| 25 |
#define SET_READ 0x8000 /* usage: or operation */ |
| 26 |
|
| 27 |
static const struct wfx_platform_data pdata_wf200 = { |
| 28 |
.file_fw = "wfx/wfm_wf200", |
| 29 |
.file_pds = "wfx/wf200.pds", |
| 30 |
.use_rising_clk = true, |
| 31 |
}; |
| 32 |
|
| 33 |
static const struct wfx_platform_data pdata_brd4001a = { |
| 34 |
.file_fw = "wfx/wfm_wf200", |
| 35 |
.file_pds = "wfx/brd4001a.pds", |
| 36 |
.use_rising_clk = true, |
| 37 |
}; |
| 38 |
|
| 39 |
static const struct wfx_platform_data pdata_brd8022a = { |
| 40 |
.file_fw = "wfx/wfm_wf200", |
| 41 |
.file_pds = "wfx/brd8022a.pds", |
| 42 |
.use_rising_clk = true, |
| 43 |
}; |
| 44 |
|
| 45 |
static const struct wfx_platform_data pdata_brd8023a = { |
| 46 |
.file_fw = "wfx/wfm_wf200", |
| 47 |
.file_pds = "wfx/brd8023a.pds", |
| 48 |
.use_rising_clk = true, |
| 49 |
}; |
| 50 |
|
| 51 |
struct wfx_spi_priv { |
| 52 |
struct spi_device *func; |
| 53 |
struct wfx_dev *core; |
| 54 |
struct gpio_desc *gpio_reset; |
| 55 |
bool need_swab; |
| 56 |
}; |
| 57 |
|
| 58 |
/* The chip reads 16bits of data at time and place them directly into (little endian) CPU register. |
| 59 |
* So, the chip expects bytes order to be "B1 B0 B3 B2" (while LE is "B0 B1 B2 B3" and BE is |
| 60 |
* "B3 B2 B1 B0") |
| 61 |
* |
| 62 |
* A little endian host with bits_per_word == 16 should do the right job natively. The code below to |
| 63 |
* support big endian host and commonly used SPI 8bits. |
| 64 |
*/ |
| 65 |
static int wfx_spi_copy_from_io(void *priv, unsigned int addr, void *dst, size_t count) |
| 66 |
{ |
| 67 |
struct wfx_spi_priv *bus = priv; |
| 68 |
u16 regaddr = (addr << 12) | (count / 2) | SET_READ; |
| 69 |
struct spi_message m; |
| 70 |
struct spi_transfer t_addr = { |
| 71 |
.tx_buf = ®addr, |
| 72 |
.len = sizeof(regaddr), |
| 73 |
}; |
| 74 |
struct spi_transfer t_msg = { |
| 75 |
.rx_buf = dst, |
| 76 |
.len = count, |
| 77 |
}; |
| 78 |
u16 *dst16 = dst; |
| 79 |
int ret, i; |
| 80 |
|
| 81 |
WARN(count % 2, "buffer size must be a multiple of 2"); |
| 82 |
|
| 83 |
cpu_to_le16s(®addr); |
| 84 |
if (bus->need_swab) |
| 85 |
swab16s(®addr); |
| 86 |
|
| 87 |
spi_message_init(&m); |
| 88 |
spi_message_add_tail(&t_addr, &m); |
| 89 |
spi_message_add_tail(&t_msg, &m); |
| 90 |
ret = spi_sync(bus->func, &m); |
| 91 |
|
| 92 |
if (bus->need_swab && addr == WFX_REG_CONFIG) |
| 93 |
for (i = 0; i < count / 2; i++) |
| 94 |
swab16s(&dst16[i]); |
| 95 |
return ret; |
| 96 |
} |
| 97 |
|
| 98 |
static int wfx_spi_copy_to_io(void *priv, unsigned int addr, const void *src, size_t count) |
| 99 |
{ |
| 100 |
struct wfx_spi_priv *bus = priv; |
| 101 |
u16 regaddr = (addr << 12) | (count / 2); |
| 102 |
/* FIXME: use a bounce buffer */ |
| 103 |
u16 *src16 = (void *)src; |
| 104 |
int ret, i; |
| 105 |
struct spi_message m; |
| 106 |
struct spi_transfer t_addr = { |
| 107 |
.tx_buf = ®addr, |
| 108 |
.len = sizeof(regaddr), |
| 109 |
}; |
| 110 |
struct spi_transfer t_msg = { |
| 111 |
.tx_buf = src, |
| 112 |
.len = count, |
| 113 |
}; |
| 114 |
|
| 115 |
WARN(count % 2, "buffer size must be a multiple of 2"); |
| 116 |
WARN(regaddr & SET_READ, "bad addr or size overflow"); |
| 117 |
|
| 118 |
cpu_to_le16s(®addr); |
| 119 |
|
| 120 |
/* Register address and CONFIG content always use 16bit big endian |
| 121 |
* ("BADC" order) |
| 122 |
*/ |
| 123 |
if (bus->need_swab) |
| 124 |
swab16s(®addr); |
| 125 |
if (bus->need_swab && addr == WFX_REG_CONFIG) |
| 126 |
for (i = 0; i < count / 2; i++) |
| 127 |
swab16s(&src16[i]); |
| 128 |
|
| 129 |
spi_message_init(&m); |
| 130 |
spi_message_add_tail(&t_addr, &m); |
| 131 |
spi_message_add_tail(&t_msg, &m); |
| 132 |
ret = spi_sync(bus->func, &m); |
| 133 |
|
| 134 |
if (bus->need_swab && addr == WFX_REG_CONFIG) |
| 135 |
for (i = 0; i < count / 2; i++) |
| 136 |
swab16s(&src16[i]); |
| 137 |
return ret; |
| 138 |
} |
| 139 |
|
| 140 |
static void wfx_spi_lock(void *priv) |
| 141 |
{ |
| 142 |
} |
| 143 |
|
| 144 |
static void wfx_spi_unlock(void *priv) |
| 145 |
{ |
| 146 |
} |
| 147 |
|
| 148 |
static irqreturn_t wfx_spi_irq_handler(int irq, void *priv) |
| 149 |
{ |
| 150 |
struct wfx_spi_priv *bus = priv; |
| 151 |
|
| 152 |
wfx_bh_request_rx(bus->core); |
| 153 |
return IRQ_HANDLED; |
| 154 |
} |
| 155 |
|
| 156 |
static int wfx_spi_irq_subscribe(void *priv) |
| 157 |
{ |
| 158 |
struct wfx_spi_priv *bus = priv; |
| 159 |
u32 flags; |
| 160 |
|
| 161 |
flags = irq_get_trigger_type(bus->func->irq); |
| 162 |
if (!flags) |
| 163 |
flags = IRQF_TRIGGER_HIGH; |
| 164 |
flags |= IRQF_ONESHOT; |
| 165 |
return devm_request_threaded_irq(&bus->func->dev, bus->func->irq, NULL, |
| 166 |
wfx_spi_irq_handler, flags, "wfx", bus); |
| 167 |
} |
| 168 |
|
| 169 |
static int wfx_spi_irq_unsubscribe(void *priv) |
| 170 |
{ |
| 171 |
struct wfx_spi_priv *bus = priv; |
| 172 |
|
| 173 |
devm_free_irq(&bus->func->dev, bus->func->irq, bus); |
| 174 |
return 0; |
| 175 |
} |
| 176 |
|
| 177 |
static size_t wfx_spi_align_size(void *priv, size_t size) |
| 178 |
{ |
| 179 |
/* Most of SPI controllers avoid DMA if buffer size is not 32bit aligned */ |
| 180 |
return ALIGN(size, 4); |
| 181 |
} |
| 182 |
|
| 183 |
static void wfx_spi_set_wakeup(void *priv, bool enabled) |
| 184 |
{ |
| 185 |
struct wfx_spi_priv *bus = priv; |
| 186 |
|
| 187 |
device_set_wakeup_enable(&bus->func->dev, enabled); |
| 188 |
} |
| 189 |
|
| 190 |
static const struct wfx_hwbus_ops wfx_spi_hwbus_ops = { |
| 191 |
.copy_from_io = wfx_spi_copy_from_io, |
| 192 |
.copy_to_io = wfx_spi_copy_to_io, |
| 193 |
.irq_subscribe = wfx_spi_irq_subscribe, |
| 194 |
.irq_unsubscribe = wfx_spi_irq_unsubscribe, |
| 195 |
.lock = wfx_spi_lock, |
| 196 |
.unlock = wfx_spi_unlock, |
| 197 |
.align_size = wfx_spi_align_size, |
| 198 |
.set_wakeup = wfx_spi_set_wakeup, |
| 199 |
}; |
| 200 |
|
| 201 |
static int wfx_spi_suspend(struct device *dev) |
| 202 |
{ |
| 203 |
struct spi_device *func = to_spi_device(dev); |
| 204 |
struct wfx_spi_priv *bus = spi_get_drvdata(func); |
| 205 |
|
| 206 |
if (!device_may_wakeup(dev)) |
| 207 |
return 0; |
| 208 |
flush_work(&bus->core->hif.bh); |
| 209 |
return enable_irq_wake(func->irq); |
| 210 |
} |
| 211 |
|
| 212 |
static int wfx_spi_resume(struct device *dev) |
| 213 |
{ |
| 214 |
struct spi_device *func = to_spi_device(dev); |
| 215 |
|
| 216 |
if (!device_may_wakeup(dev)) |
| 217 |
return 0; |
| 218 |
return disable_irq_wake(func->irq); |
| 219 |
} |
| 220 |
|
| 221 |
static int wfx_spi_probe(struct spi_device *func) |
| 222 |
{ |
| 223 |
struct wfx_platform_data *pdata; |
| 224 |
struct wfx_spi_priv *bus; |
| 225 |
int ret; |
| 226 |
|
| 227 |
if (!func->bits_per_word) |
| 228 |
func->bits_per_word = 16; |
| 229 |
ret = spi_setup(func); |
| 230 |
if (ret) |
| 231 |
return ret; |
| 232 |
pdata = (struct wfx_platform_data *)spi_get_device_id(func)->driver_data; |
| 233 |
if (!pdata) { |
| 234 |
dev_err(&func->dev, "unable to retrieve driver data (please report)\n"); |
| 235 |
return -ENODEV; |
| 236 |
} |
| 237 |
|
| 238 |
/* Trace below is also displayed by spi_setup() if compiled with DEBUG */ |
| 239 |
dev_dbg(&func->dev, "SPI params: CS=%d, mode=%d bits/word=%d speed=%d\n", |
| 240 |
spi_get_chipselect(func, 0), func->mode, func->bits_per_word, func->max_speed_hz); |
| 241 |
if (func->bits_per_word != 16 && func->bits_per_word != 8) |
| 242 |
dev_warn(&func->dev, "unusual bits/word value: %d\n", func->bits_per_word); |
| 243 |
if (func->max_speed_hz > 50000000) |
| 244 |
dev_warn(&func->dev, "%dHz is a very high speed\n", func->max_speed_hz); |
| 245 |
|
| 246 |
bus = devm_kzalloc(&func->dev, sizeof(*bus), GFP_KERNEL); |
| 247 |
if (!bus) |
| 248 |
return -ENOMEM; |
| 249 |
bus->func = func; |
| 250 |
if (func->bits_per_word == 8 || IS_ENABLED(CONFIG_CPU_BIG_ENDIAN)) |
| 251 |
bus->need_swab = true; |
| 252 |
spi_set_drvdata(func, bus); |
| 253 |
|
| 254 |
bus->gpio_reset = devm_gpiod_get_optional(&func->dev, "reset", GPIOD_OUT_LOW); |
| 255 |
if (IS_ERR(bus->gpio_reset)) |
| 256 |
return PTR_ERR(bus->gpio_reset); |
| 257 |
if (!bus->gpio_reset) { |
| 258 |
dev_warn(&func->dev, "gpio reset is not defined, trying to load firmware anyway\n"); |
| 259 |
} else { |
| 260 |
gpiod_set_consumer_name(bus->gpio_reset, "wfx reset"); |
| 261 |
gpiod_set_value_cansleep(bus->gpio_reset, 1); |
| 262 |
usleep_range(100, 150); |
| 263 |
gpiod_set_value_cansleep(bus->gpio_reset, 0); |
| 264 |
usleep_range(2000, 2500); |
| 265 |
} |
| 266 |
|
| 267 |
bus->core = wfx_init_common(&func->dev, pdata, &wfx_spi_hwbus_ops, bus); |
| 268 |
if (!bus->core) |
| 269 |
return -EIO; |
| 270 |
|
| 271 |
ret = wfx_probe(bus->core); |
| 272 |
if (ret) |
| 273 |
return ret; |
| 274 |
|
| 275 |
device_set_wakeup_capable(&func->dev, true); |
| 276 |
return 0; |
| 277 |
} |
| 278 |
|
| 279 |
static void wfx_spi_remove(struct spi_device *func) |
| 280 |
{ |
| 281 |
struct wfx_spi_priv *bus = spi_get_drvdata(func); |
| 282 |
|
| 283 |
wfx_release(bus->core); |
| 284 |
} |
| 285 |
|
| 286 |
/* For dynamic driver binding, kernel does not use OF to match driver. It only |
| 287 |
* use modalias and modalias is a copy of 'compatible' DT node with vendor |
| 288 |
* stripped. |
| 289 |
*/ |
| 290 |
static const struct spi_device_id wfx_spi_id[] = { |
| 291 |
{ "wf200", (kernel_ulong_t)&pdata_wf200 }, |
| 292 |
{ "brd4001a", (kernel_ulong_t)&pdata_brd4001a }, |
| 293 |
{ "brd8022a", (kernel_ulong_t)&pdata_brd8022a }, |
| 294 |
{ "brd8023a", (kernel_ulong_t)&pdata_brd8023a }, |
| 295 |
{ }, |
| 296 |
}; |
| 297 |
MODULE_DEVICE_TABLE(spi, wfx_spi_id); |
| 298 |
|
| 299 |
#ifdef CONFIG_OF |
| 300 |
static const struct of_device_id wfx_spi_of_match[] = { |
| 301 |
{ .compatible = "silabs,wf200" }, |
| 302 |
{ .compatible = "silabs,brd4001a" }, |
| 303 |
{ .compatible = "silabs,brd8022a" }, |
| 304 |
{ .compatible = "silabs,brd8023a" }, |
| 305 |
{ }, |
| 306 |
}; |
| 307 |
MODULE_DEVICE_TABLE(of, wfx_spi_of_match); |
| 308 |
#endif |
| 309 |
|
| 310 |
static DEFINE_SIMPLE_DEV_PM_OPS(wfx_spi_pm_ops, wfx_spi_suspend, wfx_spi_resume); |
| 311 |
|
| 312 |
struct spi_driver wfx_spi_driver = { |
| 313 |
.id_table = wfx_spi_id, |
| 314 |
.probe = wfx_spi_probe, |
| 315 |
.remove = wfx_spi_remove, |
| 316 |
.driver = { |
| 317 |
.name = "wfx-spi", |
| 318 |
.of_match_table = of_match_ptr(wfx_spi_of_match), |
| 319 |
.pm = &wfx_spi_pm_ops, |
| 320 |
}, |
| 321 |
}; |