| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/* |
| 3 |
* Linux device driver for RTL8187 |
| 4 |
* |
| 5 |
* Copyright 2007 Michael Wu <[email protected]> |
| 6 |
* Copyright 2007 Andrea Merello <[email protected]> |
| 7 |
* |
| 8 |
* Based on the r8187 driver, which is: |
| 9 |
* Copyright 2005 Andrea Merello <[email protected]>, et al. |
| 10 |
* |
| 11 |
* The driver was extended to the RTL8187B in 2008 by: |
| 12 |
* Herton Ronaldo Krzesinski <[email protected]> |
| 13 |
* Hin-Tak Leung <[email protected]> |
| 14 |
* Larry Finger <[email protected]> |
| 15 |
* |
| 16 |
* Magic delays and register offsets below are taken from the original |
| 17 |
* r8187 driver sources. Thanks to Realtek for their support! |
| 18 |
*/ |
| 19 |
|
| 20 |
#include <linux/usb.h> |
| 21 |
#include <linux/slab.h> |
| 22 |
#include <linux/delay.h> |
| 23 |
#include <linux/etherdevice.h> |
| 24 |
#include <linux/eeprom_93cx6.h> |
| 25 |
#include <linux/module.h> |
| 26 |
#include <net/mac80211.h> |
| 27 |
|
| 28 |
#include "rtl8187.h" |
| 29 |
#include "rtl8225.h" |
| 30 |
#ifdef CONFIG_RTL8187_LEDS |
| 31 |
#include "leds.h" |
| 32 |
#endif |
| 33 |
#include "rfkill.h" |
| 34 |
|
| 35 |
MODULE_AUTHOR("Michael Wu <[email protected]>"); |
| 36 |
MODULE_AUTHOR("Andrea Merello <[email protected]>"); |
| 37 |
MODULE_AUTHOR("Herton Ronaldo Krzesinski <[email protected]>"); |
| 38 |
MODULE_AUTHOR("Hin-Tak Leung <[email protected]>"); |
| 39 |
MODULE_AUTHOR("Larry Finger <[email protected]>"); |
| 40 |
MODULE_DESCRIPTION("RTL8187/RTL8187B USB wireless driver"); |
| 41 |
MODULE_LICENSE("GPL"); |
| 42 |
|
| 43 |
static const struct usb_device_id rtl8187_table[] = { |
| 44 |
/* Asus */ |
| 45 |
{USB_DEVICE(0x0b05, 0x171d), .driver_info = DEVICE_RTL8187}, |
| 46 |
/* Belkin */ |
| 47 |
{USB_DEVICE(0x050d, 0x705e), .driver_info = DEVICE_RTL8187B}, |
| 48 |
/* Realtek */ |
| 49 |
{USB_DEVICE(0x0bda, 0x8187), .driver_info = DEVICE_RTL8187}, |
| 50 |
{USB_DEVICE(0x0bda, 0x8189), .driver_info = DEVICE_RTL8187B}, |
| 51 |
{USB_DEVICE(0x0bda, 0x8197), .driver_info = DEVICE_RTL8187B}, |
| 52 |
{USB_DEVICE(0x0bda, 0x8198), .driver_info = DEVICE_RTL8187B}, |
| 53 |
/* Surecom */ |
| 54 |
{USB_DEVICE(0x0769, 0x11F2), .driver_info = DEVICE_RTL8187}, |
| 55 |
/* Logitech */ |
| 56 |
{USB_DEVICE(0x0789, 0x010C), .driver_info = DEVICE_RTL8187}, |
| 57 |
/* Netgear */ |
| 58 |
{USB_DEVICE(0x0846, 0x6100), .driver_info = DEVICE_RTL8187}, |
| 59 |
{USB_DEVICE(0x0846, 0x6a00), .driver_info = DEVICE_RTL8187}, |
| 60 |
{USB_DEVICE(0x0846, 0x4260), .driver_info = DEVICE_RTL8187B}, |
| 61 |
/* HP */ |
| 62 |
{USB_DEVICE(0x03f0, 0xca02), .driver_info = DEVICE_RTL8187}, |
| 63 |
/* Sitecom */ |
| 64 |
{USB_DEVICE(0x0df6, 0x000d), .driver_info = DEVICE_RTL8187}, |
| 65 |
{USB_DEVICE(0x0df6, 0x0028), .driver_info = DEVICE_RTL8187B}, |
| 66 |
{USB_DEVICE(0x0df6, 0x0029), .driver_info = DEVICE_RTL8187B}, |
| 67 |
/* Sphairon Access Systems GmbH */ |
| 68 |
{USB_DEVICE(0x114B, 0x0150), .driver_info = DEVICE_RTL8187}, |
| 69 |
/* Dick Smith Electronics */ |
| 70 |
{USB_DEVICE(0x1371, 0x9401), .driver_info = DEVICE_RTL8187}, |
| 71 |
/* Abocom */ |
| 72 |
{USB_DEVICE(0x13d1, 0xabe6), .driver_info = DEVICE_RTL8187}, |
| 73 |
/* Qcom */ |
| 74 |
{USB_DEVICE(0x18E8, 0x6232), .driver_info = DEVICE_RTL8187}, |
| 75 |
/* AirLive */ |
| 76 |
{USB_DEVICE(0x1b75, 0x8187), .driver_info = DEVICE_RTL8187}, |
| 77 |
/* Linksys */ |
| 78 |
{USB_DEVICE(0x1737, 0x0073), .driver_info = DEVICE_RTL8187B}, |
| 79 |
{} |
| 80 |
}; |
| 81 |
|
| 82 |
MODULE_DEVICE_TABLE(usb, rtl8187_table); |
| 83 |
|
| 84 |
static const struct ieee80211_rate rtl818x_rates[] = { |
| 85 |
{ .bitrate = 10, .hw_value = 0, }, |
| 86 |
{ .bitrate = 20, .hw_value = 1, }, |
| 87 |
{ .bitrate = 55, .hw_value = 2, }, |
| 88 |
{ .bitrate = 110, .hw_value = 3, }, |
| 89 |
{ .bitrate = 60, .hw_value = 4, }, |
| 90 |
{ .bitrate = 90, .hw_value = 5, }, |
| 91 |
{ .bitrate = 120, .hw_value = 6, }, |
| 92 |
{ .bitrate = 180, .hw_value = 7, }, |
| 93 |
{ .bitrate = 240, .hw_value = 8, }, |
| 94 |
{ .bitrate = 360, .hw_value = 9, }, |
| 95 |
{ .bitrate = 480, .hw_value = 10, }, |
| 96 |
{ .bitrate = 540, .hw_value = 11, }, |
| 97 |
}; |
| 98 |
|
| 99 |
static const struct ieee80211_channel rtl818x_channels[] = { |
| 100 |
{ .center_freq = 2412 }, |
| 101 |
{ .center_freq = 2417 }, |
| 102 |
{ .center_freq = 2422 }, |
| 103 |
{ .center_freq = 2427 }, |
| 104 |
{ .center_freq = 2432 }, |
| 105 |
{ .center_freq = 2437 }, |
| 106 |
{ .center_freq = 2442 }, |
| 107 |
{ .center_freq = 2447 }, |
| 108 |
{ .center_freq = 2452 }, |
| 109 |
{ .center_freq = 2457 }, |
| 110 |
{ .center_freq = 2462 }, |
| 111 |
{ .center_freq = 2467 }, |
| 112 |
{ .center_freq = 2472 }, |
| 113 |
{ .center_freq = 2484 }, |
| 114 |
}; |
| 115 |
|
| 116 |
static void rtl8187_iowrite_async_cb(struct urb *urb) |
| 117 |
{ |
| 118 |
kfree(urb->context); |
| 119 |
} |
| 120 |
|
| 121 |
static void rtl8187_iowrite_async(struct rtl8187_priv *priv, __le16 addr, |
| 122 |
void *data, u16 len) |
| 123 |
{ |
| 124 |
struct usb_ctrlrequest *dr; |
| 125 |
struct urb *urb; |
| 126 |
struct rtl8187_async_write_data { |
| 127 |
u8 data[4]; |
| 128 |
struct usb_ctrlrequest dr; |
| 129 |
} *buf; |
| 130 |
int rc; |
| 131 |
|
| 132 |
buf = kmalloc_obj(*buf, GFP_ATOMIC); |
| 133 |
if (!buf) |
| 134 |
return; |
| 135 |
|
| 136 |
urb = usb_alloc_urb(0, GFP_ATOMIC); |
| 137 |
if (!urb) { |
| 138 |
kfree(buf); |
| 139 |
return; |
| 140 |
} |
| 141 |
|
| 142 |
dr = &buf->dr; |
| 143 |
|
| 144 |
dr->bRequestType = RTL8187_REQT_WRITE; |
| 145 |
dr->bRequest = RTL8187_REQ_SET_REG; |
| 146 |
dr->wValue = addr; |
| 147 |
dr->wIndex = 0; |
| 148 |
dr->wLength = cpu_to_le16(len); |
| 149 |
|
| 150 |
memcpy(buf, data, len); |
| 151 |
|
| 152 |
usb_fill_control_urb(urb, priv->udev, usb_sndctrlpipe(priv->udev, 0), |
| 153 |
(unsigned char *)dr, buf, len, |
| 154 |
rtl8187_iowrite_async_cb, buf); |
| 155 |
usb_anchor_urb(urb, &priv->anchored); |
| 156 |
rc = usb_submit_urb(urb, GFP_ATOMIC); |
| 157 |
if (rc < 0) { |
| 158 |
kfree(buf); |
| 159 |
usb_unanchor_urb(urb); |
| 160 |
} |
| 161 |
usb_free_urb(urb); |
| 162 |
} |
| 163 |
|
| 164 |
static inline void rtl818x_iowrite32_async(struct rtl8187_priv *priv, |
| 165 |
__le32 *addr, u32 val) |
| 166 |
{ |
| 167 |
__le32 buf = cpu_to_le32(val); |
| 168 |
|
| 169 |
rtl8187_iowrite_async(priv, cpu_to_le16((unsigned long)addr), |
| 170 |
&buf, sizeof(buf)); |
| 171 |
} |
| 172 |
|
| 173 |
void rtl8187_write_phy(struct ieee80211_hw *dev, u8 addr, u32 data) |
| 174 |
{ |
| 175 |
struct rtl8187_priv *priv = dev->priv; |
| 176 |
|
| 177 |
data <<= 8; |
| 178 |
data |= addr | 0x80; |
| 179 |
|
| 180 |
rtl818x_iowrite8(priv, &priv->map->PHY[3], (data >> 24) & 0xFF); |
| 181 |
rtl818x_iowrite8(priv, &priv->map->PHY[2], (data >> 16) & 0xFF); |
| 182 |
rtl818x_iowrite8(priv, &priv->map->PHY[1], (data >> 8) & 0xFF); |
| 183 |
rtl818x_iowrite8(priv, &priv->map->PHY[0], data & 0xFF); |
| 184 |
} |
| 185 |
|
| 186 |
static void rtl8187_tx_cb(struct urb *urb) |
| 187 |
{ |
| 188 |
struct sk_buff *skb = (struct sk_buff *)urb->context; |
| 189 |
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); |
| 190 |
struct ieee80211_hw *hw = info->rate_driver_data[0]; |
| 191 |
struct rtl8187_priv *priv = hw->priv; |
| 192 |
|
| 193 |
skb_pull(skb, priv->is_rtl8187b ? sizeof(struct rtl8187b_tx_hdr) : |
| 194 |
sizeof(struct rtl8187_tx_hdr)); |
| 195 |
ieee80211_tx_info_clear_status(info); |
| 196 |
|
| 197 |
if (!(urb->status) && !(info->flags & IEEE80211_TX_CTL_NO_ACK)) { |
| 198 |
if (priv->is_rtl8187b) { |
| 199 |
skb_queue_tail(&priv->b_tx_status.queue, skb); |
| 200 |
|
| 201 |
/* queue is "full", discard last items */ |
| 202 |
while (skb_queue_len(&priv->b_tx_status.queue) > 5) { |
| 203 |
struct sk_buff *old_skb; |
| 204 |
|
| 205 |
dev_dbg(&priv->udev->dev, |
| 206 |
"transmit status queue full\n"); |
| 207 |
|
| 208 |
old_skb = skb_dequeue(&priv->b_tx_status.queue); |
| 209 |
ieee80211_tx_status_irqsafe(hw, old_skb); |
| 210 |
} |
| 211 |
return; |
| 212 |
} else { |
| 213 |
info->flags |= IEEE80211_TX_STAT_ACK; |
| 214 |
} |
| 215 |
} |
| 216 |
if (priv->is_rtl8187b) |
| 217 |
ieee80211_tx_status_irqsafe(hw, skb); |
| 218 |
else { |
| 219 |
/* Retry information for the RTI8187 is only available by |
| 220 |
* reading a register in the device. We are in interrupt mode |
| 221 |
* here, thus queue the skb and finish on a work queue. */ |
| 222 |
skb_queue_tail(&priv->b_tx_status.queue, skb); |
| 223 |
ieee80211_queue_delayed_work(hw, &priv->work, 0); |
| 224 |
} |
| 225 |
} |
| 226 |
|
| 227 |
static void rtl8187_tx(struct ieee80211_hw *dev, |
| 228 |
struct ieee80211_tx_control *control, |
| 229 |
struct sk_buff *skb) |
| 230 |
{ |
| 231 |
struct rtl8187_priv *priv = dev->priv; |
| 232 |
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); |
| 233 |
struct ieee80211_hdr *tx_hdr = (struct ieee80211_hdr *)(skb->data); |
| 234 |
unsigned int ep; |
| 235 |
void *buf; |
| 236 |
struct urb *urb; |
| 237 |
__le16 rts_dur = 0; |
| 238 |
u32 flags; |
| 239 |
int rc; |
| 240 |
|
| 241 |
urb = usb_alloc_urb(0, GFP_ATOMIC); |
| 242 |
if (!urb) { |
| 243 |
kfree_skb(skb); |
| 244 |
return; |
| 245 |
} |
| 246 |
|
| 247 |
flags = skb->len; |
| 248 |
flags |= RTL818X_TX_DESC_FLAG_NO_ENC; |
| 249 |
|
| 250 |
flags |= ieee80211_get_tx_rate(dev, info)->hw_value << 24; |
| 251 |
if (ieee80211_has_morefrags(tx_hdr->frame_control)) |
| 252 |
flags |= RTL818X_TX_DESC_FLAG_MOREFRAG; |
| 253 |
|
| 254 |
/* HW will perform RTS-CTS when only RTS flags is set. |
| 255 |
* HW will perform CTS-to-self when both RTS and CTS flags are set. |
| 256 |
* RTS rate and RTS duration will be used also for CTS-to-self. |
| 257 |
*/ |
| 258 |
if (info->control.rates[0].flags & IEEE80211_TX_RC_USE_RTS_CTS) { |
| 259 |
flags |= RTL818X_TX_DESC_FLAG_RTS; |
| 260 |
flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19; |
| 261 |
rts_dur = ieee80211_rts_duration(dev, priv->vif, |
| 262 |
skb->len, info); |
| 263 |
} else if (info->control.rates[0].flags & IEEE80211_TX_RC_USE_CTS_PROTECT) { |
| 264 |
flags |= RTL818X_TX_DESC_FLAG_RTS | RTL818X_TX_DESC_FLAG_CTS; |
| 265 |
flags |= ieee80211_get_rts_cts_rate(dev, info)->hw_value << 19; |
| 266 |
rts_dur = ieee80211_ctstoself_duration(dev, priv->vif, |
| 267 |
skb->len, info); |
| 268 |
} |
| 269 |
|
| 270 |
if (info->flags & IEEE80211_TX_CTL_ASSIGN_SEQ) { |
| 271 |
if (info->flags & IEEE80211_TX_CTL_FIRST_FRAGMENT) |
| 272 |
priv->seqno += 0x10; |
| 273 |
tx_hdr->seq_ctrl &= cpu_to_le16(IEEE80211_SCTL_FRAG); |
| 274 |
tx_hdr->seq_ctrl |= cpu_to_le16(priv->seqno); |
| 275 |
} |
| 276 |
|
| 277 |
if (!priv->is_rtl8187b) { |
| 278 |
struct rtl8187_tx_hdr *hdr = skb_push(skb, sizeof(*hdr)); |
| 279 |
hdr->flags = cpu_to_le32(flags); |
| 280 |
hdr->len = 0; |
| 281 |
hdr->rts_duration = rts_dur; |
| 282 |
hdr->retry = cpu_to_le32((info->control.rates[0].count - 1) << 8); |
| 283 |
buf = hdr; |
| 284 |
|
| 285 |
ep = 2; |
| 286 |
} else { |
| 287 |
/* fc needs to be calculated before skb_push() */ |
| 288 |
unsigned int epmap[4] = { 6, 7, 5, 4 }; |
| 289 |
u16 fc = le16_to_cpu(tx_hdr->frame_control); |
| 290 |
|
| 291 |
struct rtl8187b_tx_hdr *hdr = skb_push(skb, sizeof(*hdr)); |
| 292 |
struct ieee80211_rate *txrate = |
| 293 |
ieee80211_get_tx_rate(dev, info); |
| 294 |
memset(hdr, 0, sizeof(*hdr)); |
| 295 |
hdr->flags = cpu_to_le32(flags); |
| 296 |
hdr->rts_duration = rts_dur; |
| 297 |
hdr->retry = cpu_to_le32((info->control.rates[0].count - 1) << 8); |
| 298 |
hdr->tx_duration = |
| 299 |
ieee80211_generic_frame_duration(dev, priv->vif, |
| 300 |
info->band, |
| 301 |
skb->len, txrate); |
| 302 |
buf = hdr; |
| 303 |
|
| 304 |
if ((fc & IEEE80211_FCTL_FTYPE) == IEEE80211_FTYPE_MGMT) |
| 305 |
ep = 12; |
| 306 |
else |
| 307 |
ep = epmap[skb_get_queue_mapping(skb)]; |
| 308 |
} |
| 309 |
|
| 310 |
info->rate_driver_data[0] = dev; |
| 311 |
info->rate_driver_data[1] = urb; |
| 312 |
|
| 313 |
usb_fill_bulk_urb(urb, priv->udev, usb_sndbulkpipe(priv->udev, ep), |
| 314 |
buf, skb->len, rtl8187_tx_cb, skb); |
| 315 |
urb->transfer_flags |= URB_ZERO_PACKET; |
| 316 |
usb_anchor_urb(urb, &priv->anchored); |
| 317 |
rc = usb_submit_urb(urb, GFP_ATOMIC); |
| 318 |
if (rc < 0) { |
| 319 |
usb_unanchor_urb(urb); |
| 320 |
kfree_skb(skb); |
| 321 |
} |
| 322 |
usb_free_urb(urb); |
| 323 |
} |
| 324 |
|
| 325 |
static void rtl8187_rx_cb(struct urb *urb) |
| 326 |
{ |
| 327 |
struct sk_buff *skb = (struct sk_buff *)urb->context; |
| 328 |
struct rtl8187_rx_info *info = (struct rtl8187_rx_info *)skb->cb; |
| 329 |
struct ieee80211_hw *dev = info->dev; |
| 330 |
struct rtl8187_priv *priv = dev->priv; |
| 331 |
struct ieee80211_rx_status rx_status = { 0 }; |
| 332 |
int rate, signal; |
| 333 |
u32 flags; |
| 334 |
unsigned long f; |
| 335 |
|
| 336 |
spin_lock_irqsave(&priv->rx_queue.lock, f); |
| 337 |
__skb_unlink(skb, &priv->rx_queue); |
| 338 |
spin_unlock_irqrestore(&priv->rx_queue.lock, f); |
| 339 |
skb_put(skb, urb->actual_length); |
| 340 |
|
| 341 |
if (unlikely(urb->status)) |
| 342 |
goto free_skb; |
| 343 |
|
| 344 |
if (!priv->is_rtl8187b) { |
| 345 |
struct rtl8187_rx_hdr *hdr; |
| 346 |
|
| 347 |
if (skb->len < sizeof(struct rtl8187_rx_hdr)) |
| 348 |
goto free_skb; |
| 349 |
|
| 350 |
hdr = (typeof(hdr))(skb_tail_pointer(skb) - sizeof(*hdr)); |
| 351 |
flags = le32_to_cpu(hdr->flags); |
| 352 |
/* As with the RTL8187B below, the AGC is used to calculate |
| 353 |
* signal strength. In this case, the scaling |
| 354 |
* constants are derived from the output of p54usb. |
| 355 |
*/ |
| 356 |
signal = -4 - ((27 * hdr->agc) >> 6); |
| 357 |
rx_status.antenna = (hdr->signal >> 7) & 1; |
| 358 |
rx_status.mactime = le64_to_cpu(hdr->mac_time); |
| 359 |
} else { |
| 360 |
struct rtl8187b_rx_hdr *hdr; |
| 361 |
|
| 362 |
if (skb->len < sizeof(struct rtl8187b_rx_hdr)) |
| 363 |
goto free_skb; |
| 364 |
|
| 365 |
hdr = (typeof(hdr))(skb_tail_pointer(skb) - sizeof(*hdr)); |
| 366 |
/* The Realtek datasheet for the RTL8187B shows that the RX |
| 367 |
* header contains the following quantities: signal quality, |
| 368 |
* RSSI, AGC, the received power in dB, and the measured SNR. |
| 369 |
* In testing, none of these quantities show qualitative |
| 370 |
* agreement with AP signal strength, except for the AGC, |
| 371 |
* which is inversely proportional to the strength of the |
| 372 |
* signal. In the following, the signal strength |
| 373 |
* is derived from the AGC. The arbitrary scaling constants |
| 374 |
* are chosen to make the results close to the values obtained |
| 375 |
* for a BCM4312 using b43 as the driver. The noise is ignored |
| 376 |
* for now. |
| 377 |
*/ |
| 378 |
flags = le32_to_cpu(hdr->flags); |
| 379 |
signal = 14 - hdr->agc / 2; |
| 380 |
rx_status.antenna = (hdr->rssi >> 7) & 1; |
| 381 |
rx_status.mactime = le64_to_cpu(hdr->mac_time); |
| 382 |
} |
| 383 |
|
| 384 |
rx_status.signal = signal; |
| 385 |
priv->signal = signal; |
| 386 |
rate = (flags >> 20) & 0xF; |
| 387 |
skb_trim(skb, flags & 0x0FFF); |
| 388 |
rx_status.rate_idx = rate; |
| 389 |
rx_status.freq = dev->conf.chandef.chan->center_freq; |
| 390 |
rx_status.band = dev->conf.chandef.chan->band; |
| 391 |
rx_status.flag |= RX_FLAG_MACTIME_START; |
| 392 |
if (flags & RTL818X_RX_DESC_FLAG_SPLCP) |
| 393 |
rx_status.enc_flags |= RX_ENC_FLAG_SHORTPRE; |
| 394 |
if (flags & RTL818X_RX_DESC_FLAG_CRC32_ERR) |
| 395 |
rx_status.flag |= RX_FLAG_FAILED_FCS_CRC; |
| 396 |
memcpy(IEEE80211_SKB_RXCB(skb), &rx_status, sizeof(rx_status)); |
| 397 |
ieee80211_rx_irqsafe(dev, skb); |
| 398 |
|
| 399 |
skb = dev_alloc_skb(RTL8187_MAX_RX); |
| 400 |
if (unlikely(!skb)) { |
| 401 |
/* TODO check rx queue length and refill *somewhere* */ |
| 402 |
return; |
| 403 |
} |
| 404 |
|
| 405 |
info = (struct rtl8187_rx_info *)skb->cb; |
| 406 |
info->urb = urb; |
| 407 |
info->dev = dev; |
| 408 |
urb->transfer_buffer = skb_tail_pointer(skb); |
| 409 |
urb->context = skb; |
| 410 |
skb_queue_tail(&priv->rx_queue, skb); |
| 411 |
|
| 412 |
usb_anchor_urb(urb, &priv->anchored); |
| 413 |
if (usb_submit_urb(urb, GFP_ATOMIC)) { |
| 414 |
usb_unanchor_urb(urb); |
| 415 |
skb_unlink(skb, &priv->rx_queue); |
| 416 |
dev_kfree_skb_irq(skb); |
| 417 |
} |
| 418 |
return; |
| 419 |
|
| 420 |
free_skb: |
| 421 |
dev_kfree_skb_irq(skb); |
| 422 |
return; |
| 423 |
} |
| 424 |
|
| 425 |
static int rtl8187_init_urbs(struct ieee80211_hw *dev) |
| 426 |
{ |
| 427 |
struct rtl8187_priv *priv = dev->priv; |
| 428 |
struct urb *entry = NULL; |
| 429 |
struct sk_buff *skb; |
| 430 |
struct rtl8187_rx_info *info; |
| 431 |
int ret = 0; |
| 432 |
|
| 433 |
while (skb_queue_len(&priv->rx_queue) < 32) { |
| 434 |
skb = __dev_alloc_skb(RTL8187_MAX_RX, GFP_KERNEL); |
| 435 |
if (!skb) { |
| 436 |
ret = -ENOMEM; |
| 437 |
goto err; |
| 438 |
} |
| 439 |
entry = usb_alloc_urb(0, GFP_KERNEL); |
| 440 |
if (!entry) { |
| 441 |
ret = -ENOMEM; |
| 442 |
goto err; |
| 443 |
} |
| 444 |
usb_fill_bulk_urb(entry, priv->udev, |
| 445 |
usb_rcvbulkpipe(priv->udev, |
| 446 |
priv->is_rtl8187b ? 3 : 1), |
| 447 |
skb_tail_pointer(skb), |
| 448 |
RTL8187_MAX_RX, rtl8187_rx_cb, skb); |
| 449 |
info = (struct rtl8187_rx_info *)skb->cb; |
| 450 |
info->urb = entry; |
| 451 |
info->dev = dev; |
| 452 |
skb_queue_tail(&priv->rx_queue, skb); |
| 453 |
usb_anchor_urb(entry, &priv->anchored); |
| 454 |
ret = usb_submit_urb(entry, GFP_KERNEL); |
| 455 |
if (ret) { |
| 456 |
skb_unlink(skb, &priv->rx_queue); |
| 457 |
usb_unanchor_urb(entry); |
| 458 |
usb_put_urb(entry); |
| 459 |
goto err; |
| 460 |
} |
| 461 |
usb_put_urb(entry); |
| 462 |
} |
| 463 |
return ret; |
| 464 |
|
| 465 |
err: |
| 466 |
kfree_skb(skb); |
| 467 |
usb_kill_anchored_urbs(&priv->anchored); |
| 468 |
return ret; |
| 469 |
} |
| 470 |
|
| 471 |
static void rtl8187b_status_cb(struct urb *urb) |
| 472 |
{ |
| 473 |
struct ieee80211_hw *hw = (struct ieee80211_hw *)urb->context; |
| 474 |
struct rtl8187_priv *priv = hw->priv; |
| 475 |
u64 val; |
| 476 |
unsigned int cmd_type; |
| 477 |
|
| 478 |
if (unlikely(urb->status)) |
| 479 |
return; |
| 480 |
|
| 481 |
/* |
| 482 |
* Read from status buffer: |
| 483 |
* |
| 484 |
* bits [30:31] = cmd type: |
| 485 |
* - 0 indicates tx beacon interrupt |
| 486 |
* - 1 indicates tx close descriptor |
| 487 |
* |
| 488 |
* In the case of tx beacon interrupt: |
| 489 |
* [0:9] = Last Beacon CW |
| 490 |
* [10:29] = reserved |
| 491 |
* [30:31] = 00b |
| 492 |
* [32:63] = Last Beacon TSF |
| 493 |
* |
| 494 |
* If it's tx close descriptor: |
| 495 |
* [0:7] = Packet Retry Count |
| 496 |
* [8:14] = RTS Retry Count |
| 497 |
* [15] = TOK |
| 498 |
* [16:27] = Sequence No |
| 499 |
* [28] = LS |
| 500 |
* [29] = FS |
| 501 |
* [30:31] = 01b |
| 502 |
* [32:47] = unused (reserved?) |
| 503 |
* [48:63] = MAC Used Time |
| 504 |
*/ |
| 505 |
val = le64_to_cpu(priv->b_tx_status.buf); |
| 506 |
|
| 507 |
cmd_type = (val >> 30) & 0x3; |
| 508 |
if (cmd_type == 1) { |
| 509 |
unsigned int pkt_rc, seq_no; |
| 510 |
bool tok; |
| 511 |
struct sk_buff *skb, *iter; |
| 512 |
struct ieee80211_hdr *ieee80211hdr; |
| 513 |
unsigned long flags; |
| 514 |
|
| 515 |
pkt_rc = val & 0xFF; |
| 516 |
tok = val & (1 << 15); |
| 517 |
seq_no = (val >> 16) & 0xFFF; |
| 518 |
|
| 519 |
spin_lock_irqsave(&priv->b_tx_status.queue.lock, flags); |
| 520 |
skb = NULL; |
| 521 |
skb_queue_reverse_walk(&priv->b_tx_status.queue, iter) { |
| 522 |
ieee80211hdr = (struct ieee80211_hdr *)iter->data; |
| 523 |
|
| 524 |
/* |
| 525 |
* While testing, it was discovered that the seq_no |
| 526 |
* doesn't actually contains the sequence number. |
| 527 |
* Instead of returning just the 12 bits of sequence |
| 528 |
* number, hardware is returning entire sequence control |
| 529 |
* (fragment number plus sequence number) in a 12 bit |
| 530 |
* only field overflowing after some time. As a |
| 531 |
* workaround, just consider the lower bits, and expect |
| 532 |
* it's unlikely we wrongly ack some sent data |
| 533 |
*/ |
| 534 |
if ((le16_to_cpu(ieee80211hdr->seq_ctrl) |
| 535 |
& 0xFFF) == seq_no) { |
| 536 |
skb = iter; |
| 537 |
break; |
| 538 |
} |
| 539 |
} |
| 540 |
if (skb) { |
| 541 |
struct ieee80211_tx_info *info = IEEE80211_SKB_CB(skb); |
| 542 |
|
| 543 |
__skb_unlink(skb, &priv->b_tx_status.queue); |
| 544 |
if (tok) |
| 545 |
info->flags |= IEEE80211_TX_STAT_ACK; |
| 546 |
info->status.rates[0].count = pkt_rc + 1; |
| 547 |
|
| 548 |
ieee80211_tx_status_irqsafe(hw, skb); |
| 549 |
} |
| 550 |
spin_unlock_irqrestore(&priv->b_tx_status.queue.lock, flags); |
| 551 |
} |
| 552 |
|
| 553 |
usb_anchor_urb(urb, &priv->anchored); |
| 554 |
if (usb_submit_urb(urb, GFP_ATOMIC)) |
| 555 |
usb_unanchor_urb(urb); |
| 556 |
} |
| 557 |
|
| 558 |
static int rtl8187b_init_status_urb(struct ieee80211_hw *dev) |
| 559 |
{ |
| 560 |
struct rtl8187_priv *priv = dev->priv; |
| 561 |
struct urb *entry; |
| 562 |
int ret = 0; |
| 563 |
|
| 564 |
entry = usb_alloc_urb(0, GFP_KERNEL); |
| 565 |
if (!entry) |
| 566 |
return -ENOMEM; |
| 567 |
|
| 568 |
usb_fill_bulk_urb(entry, priv->udev, usb_rcvbulkpipe(priv->udev, 9), |
| 569 |
&priv->b_tx_status.buf, sizeof(priv->b_tx_status.buf), |
| 570 |
rtl8187b_status_cb, dev); |
| 571 |
|
| 572 |
usb_anchor_urb(entry, &priv->anchored); |
| 573 |
ret = usb_submit_urb(entry, GFP_KERNEL); |
| 574 |
if (ret) |
| 575 |
usb_unanchor_urb(entry); |
| 576 |
usb_free_urb(entry); |
| 577 |
|
| 578 |
return ret; |
| 579 |
} |
| 580 |
|
| 581 |
static void rtl8187_set_anaparam(struct rtl8187_priv *priv, bool rfon) |
| 582 |
{ |
| 583 |
u32 anaparam, anaparam2; |
| 584 |
u8 anaparam3, reg; |
| 585 |
|
| 586 |
if (!priv->is_rtl8187b) { |
| 587 |
if (rfon) { |
| 588 |
anaparam = RTL8187_RTL8225_ANAPARAM_ON; |
| 589 |
anaparam2 = RTL8187_RTL8225_ANAPARAM2_ON; |
| 590 |
} else { |
| 591 |
anaparam = RTL8187_RTL8225_ANAPARAM_OFF; |
| 592 |
anaparam2 = RTL8187_RTL8225_ANAPARAM2_OFF; |
| 593 |
} |
| 594 |
} else { |
| 595 |
if (rfon) { |
| 596 |
anaparam = RTL8187B_RTL8225_ANAPARAM_ON; |
| 597 |
anaparam2 = RTL8187B_RTL8225_ANAPARAM2_ON; |
| 598 |
anaparam3 = RTL8187B_RTL8225_ANAPARAM3_ON; |
| 599 |
} else { |
| 600 |
anaparam = RTL8187B_RTL8225_ANAPARAM_OFF; |
| 601 |
anaparam2 = RTL8187B_RTL8225_ANAPARAM2_OFF; |
| 602 |
anaparam3 = RTL8187B_RTL8225_ANAPARAM3_OFF; |
| 603 |
} |
| 604 |
} |
| 605 |
|
| 606 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, |
| 607 |
RTL818X_EEPROM_CMD_CONFIG); |
| 608 |
reg = rtl818x_ioread8(priv, &priv->map->CONFIG3); |
| 609 |
reg |= RTL818X_CONFIG3_ANAPARAM_WRITE; |
| 610 |
rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg); |
| 611 |
rtl818x_iowrite32(priv, &priv->map->ANAPARAM, anaparam); |
| 612 |
rtl818x_iowrite32(priv, &priv->map->ANAPARAM2, anaparam2); |
| 613 |
if (priv->is_rtl8187b) |
| 614 |
rtl818x_iowrite8(priv, &priv->map->ANAPARAM3A, anaparam3); |
| 615 |
reg &= ~RTL818X_CONFIG3_ANAPARAM_WRITE; |
| 616 |
rtl818x_iowrite8(priv, &priv->map->CONFIG3, reg); |
| 617 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, |
| 618 |
RTL818X_EEPROM_CMD_NORMAL); |
| 619 |
} |
| 620 |
|
| 621 |
static int rtl8187_cmd_reset(struct ieee80211_hw *dev) |
| 622 |
{ |
| 623 |
struct rtl8187_priv *priv = dev->priv; |
| 624 |
u8 reg; |
| 625 |
int i; |
| 626 |
|
| 627 |
reg = rtl818x_ioread8(priv, &priv->map->CMD); |
| 628 |
reg &= (1 << 1); |
| 629 |
reg |= RTL818X_CMD_RESET; |
| 630 |
rtl818x_iowrite8(priv, &priv->map->CMD, reg); |
| 631 |
|
| 632 |
i = 10; |
| 633 |
do { |
| 634 |
msleep(2); |
| 635 |
if (!(rtl818x_ioread8(priv, &priv->map->CMD) & |
| 636 |
RTL818X_CMD_RESET)) |
| 637 |
break; |
| 638 |
} while (--i); |
| 639 |
|
| 640 |
if (!i) { |
| 641 |
wiphy_err(dev->wiphy, "Reset timeout!\n"); |
| 642 |
return -ETIMEDOUT; |
| 643 |
} |
| 644 |
|
| 645 |
/* reload registers from eeprom */ |
| 646 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_LOAD); |
| 647 |
|
| 648 |
i = 10; |
| 649 |
do { |
| 650 |
msleep(4); |
| 651 |
if (!(rtl818x_ioread8(priv, &priv->map->EEPROM_CMD) & |
| 652 |
RTL818X_EEPROM_CMD_CONFIG)) |
| 653 |
break; |
| 654 |
} while (--i); |
| 655 |
|
| 656 |
if (!i) { |
| 657 |
wiphy_err(dev->wiphy, "eeprom reset timeout!\n"); |
| 658 |
return -ETIMEDOUT; |
| 659 |
} |
| 660 |
|
| 661 |
return 0; |
| 662 |
} |
| 663 |
|
| 664 |
static int rtl8187_init_hw(struct ieee80211_hw *dev) |
| 665 |
{ |
| 666 |
struct rtl8187_priv *priv = dev->priv; |
| 667 |
u8 reg; |
| 668 |
int res; |
| 669 |
|
| 670 |
/* reset */ |
| 671 |
rtl8187_set_anaparam(priv, true); |
| 672 |
|
| 673 |
rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0); |
| 674 |
|
| 675 |
msleep(200); |
| 676 |
rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x10); |
| 677 |
rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x11); |
| 678 |
rtl818x_iowrite8(priv, (u8 *)0xFE18, 0x00); |
| 679 |
msleep(200); |
| 680 |
|
| 681 |
res = rtl8187_cmd_reset(dev); |
| 682 |
if (res) |
| 683 |
return res; |
| 684 |
|
| 685 |
rtl8187_set_anaparam(priv, true); |
| 686 |
|
| 687 |
/* setup card */ |
| 688 |
rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0); |
| 689 |
rtl818x_iowrite8(priv, &priv->map->GPIO0, 0); |
| 690 |
|
| 691 |
rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, (4 << 8)); |
| 692 |
rtl818x_iowrite8(priv, &priv->map->GPIO0, 1); |
| 693 |
rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0); |
| 694 |
|
| 695 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); |
| 696 |
|
| 697 |
rtl818x_iowrite16(priv, (__le16 *)0xFFF4, 0xFFFF); |
| 698 |
reg = rtl818x_ioread8(priv, &priv->map->CONFIG1); |
| 699 |
reg &= 0x3F; |
| 700 |
reg |= 0x80; |
| 701 |
rtl818x_iowrite8(priv, &priv->map->CONFIG1, reg); |
| 702 |
|
| 703 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); |
| 704 |
|
| 705 |
rtl818x_iowrite32(priv, &priv->map->INT_TIMEOUT, 0); |
| 706 |
rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0); |
| 707 |
rtl818x_iowrite8(priv, &priv->map->RATE_FALLBACK, 0); |
| 708 |
|
| 709 |
// TODO: set RESP_RATE and BRSR properly |
| 710 |
rtl818x_iowrite8(priv, &priv->map->RESP_RATE, (8 << 4) | 0); |
| 711 |
rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3); |
| 712 |
|
| 713 |
/* host_usb_init */ |
| 714 |
rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0); |
| 715 |
rtl818x_iowrite8(priv, &priv->map->GPIO0, 0); |
| 716 |
reg = rtl818x_ioread8(priv, (u8 *)0xFE53); |
| 717 |
rtl818x_iowrite8(priv, (u8 *)0xFE53, reg | (1 << 7)); |
| 718 |
rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, (4 << 8)); |
| 719 |
rtl818x_iowrite8(priv, &priv->map->GPIO0, 0x20); |
| 720 |
rtl818x_iowrite8(priv, &priv->map->GP_ENABLE, 0); |
| 721 |
rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x80); |
| 722 |
rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x80); |
| 723 |
rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x80); |
| 724 |
msleep(100); |
| 725 |
|
| 726 |
rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x000a8008); |
| 727 |
rtl818x_iowrite16(priv, &priv->map->BRSR, 0xFFFF); |
| 728 |
rtl818x_iowrite32(priv, &priv->map->RF_PARA, 0x00100044); |
| 729 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, |
| 730 |
RTL818X_EEPROM_CMD_CONFIG); |
| 731 |
rtl818x_iowrite8(priv, &priv->map->CONFIG3, 0x44); |
| 732 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, |
| 733 |
RTL818X_EEPROM_CMD_NORMAL); |
| 734 |
rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FF7); |
| 735 |
msleep(100); |
| 736 |
|
| 737 |
priv->rf->init(dev); |
| 738 |
|
| 739 |
rtl818x_iowrite16(priv, &priv->map->BRSR, 0x01F3); |
| 740 |
reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) & ~1; |
| 741 |
rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg | 1); |
| 742 |
rtl818x_iowrite16(priv, (__le16 *)0xFFFE, 0x10); |
| 743 |
rtl818x_iowrite8(priv, &priv->map->TALLY_SEL, 0x80); |
| 744 |
rtl818x_iowrite8(priv, (u8 *)0xFFFF, 0x60); |
| 745 |
rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg); |
| 746 |
|
| 747 |
return 0; |
| 748 |
} |
| 749 |
|
| 750 |
static const u8 rtl8187b_reg_table[][3] = { |
| 751 |
{0xF0, 0x32, 0}, {0xF1, 0x32, 0}, {0xF2, 0x00, 0}, {0xF3, 0x00, 0}, |
| 752 |
{0xF4, 0x32, 0}, {0xF5, 0x43, 0}, {0xF6, 0x00, 0}, {0xF7, 0x00, 0}, |
| 753 |
{0xF8, 0x46, 0}, {0xF9, 0xA4, 0}, {0xFA, 0x00, 0}, {0xFB, 0x00, 0}, |
| 754 |
{0xFC, 0x96, 0}, {0xFD, 0xA4, 0}, {0xFE, 0x00, 0}, {0xFF, 0x00, 0}, |
| 755 |
|
| 756 |
{0x58, 0x4B, 1}, {0x59, 0x00, 1}, {0x5A, 0x4B, 1}, {0x5B, 0x00, 1}, |
| 757 |
{0x60, 0x4B, 1}, {0x61, 0x09, 1}, {0x62, 0x4B, 1}, {0x63, 0x09, 1}, |
| 758 |
{0xCE, 0x0F, 1}, {0xCF, 0x00, 1}, {0xF0, 0x4E, 1}, {0xF1, 0x01, 1}, |
| 759 |
{0xF2, 0x02, 1}, {0xF3, 0x03, 1}, {0xF4, 0x04, 1}, {0xF5, 0x05, 1}, |
| 760 |
{0xF6, 0x06, 1}, {0xF7, 0x07, 1}, {0xF8, 0x08, 1}, |
| 761 |
|
| 762 |
{0x4E, 0x00, 2}, {0x0C, 0x04, 2}, {0x21, 0x61, 2}, {0x22, 0x68, 2}, |
| 763 |
{0x23, 0x6F, 2}, {0x24, 0x76, 2}, {0x25, 0x7D, 2}, {0x26, 0x84, 2}, |
| 764 |
{0x27, 0x8D, 2}, {0x4D, 0x08, 2}, {0x50, 0x05, 2}, {0x51, 0xF5, 2}, |
| 765 |
{0x52, 0x04, 2}, {0x53, 0xA0, 2}, {0x54, 0x1F, 2}, {0x55, 0x23, 2}, |
| 766 |
{0x56, 0x45, 2}, {0x57, 0x67, 2}, {0x58, 0x08, 2}, {0x59, 0x08, 2}, |
| 767 |
{0x5A, 0x08, 2}, {0x5B, 0x08, 2}, {0x60, 0x08, 2}, {0x61, 0x08, 2}, |
| 768 |
{0x62, 0x08, 2}, {0x63, 0x08, 2}, {0x64, 0xCF, 2}, |
| 769 |
|
| 770 |
{0x5B, 0x40, 0}, {0x84, 0x88, 0}, {0x85, 0x24, 0}, {0x88, 0x54, 0}, |
| 771 |
{0x8B, 0xB8, 0}, {0x8C, 0x07, 0}, {0x8D, 0x00, 0}, {0x94, 0x1B, 0}, |
| 772 |
{0x95, 0x12, 0}, {0x96, 0x00, 0}, {0x97, 0x06, 0}, {0x9D, 0x1A, 0}, |
| 773 |
{0x9F, 0x10, 0}, {0xB4, 0x22, 0}, {0xBE, 0x80, 0}, {0xDB, 0x00, 0}, |
| 774 |
{0xEE, 0x00, 0}, {0x4C, 0x00, 2}, |
| 775 |
|
| 776 |
{0x9F, 0x00, 3}, {0x8C, 0x01, 0}, {0x8D, 0x10, 0}, {0x8E, 0x08, 0}, |
| 777 |
{0x8F, 0x00, 0} |
| 778 |
}; |
| 779 |
|
| 780 |
static int rtl8187b_init_hw(struct ieee80211_hw *dev) |
| 781 |
{ |
| 782 |
struct rtl8187_priv *priv = dev->priv; |
| 783 |
int res, i; |
| 784 |
u8 reg; |
| 785 |
|
| 786 |
rtl8187_set_anaparam(priv, true); |
| 787 |
|
| 788 |
/* Reset PLL sequence on 8187B. Realtek note: reduces power |
| 789 |
* consumption about 30 mA */ |
| 790 |
rtl818x_iowrite8(priv, (u8 *)0xFF61, 0x10); |
| 791 |
reg = rtl818x_ioread8(priv, (u8 *)0xFF62); |
| 792 |
rtl818x_iowrite8(priv, (u8 *)0xFF62, reg & ~(1 << 5)); |
| 793 |
rtl818x_iowrite8(priv, (u8 *)0xFF62, reg | (1 << 5)); |
| 794 |
|
| 795 |
res = rtl8187_cmd_reset(dev); |
| 796 |
if (res) |
| 797 |
return res; |
| 798 |
|
| 799 |
rtl8187_set_anaparam(priv, true); |
| 800 |
|
| 801 |
/* BRSR (Basic Rate Set Register) on 8187B looks to be the same as |
| 802 |
* RESP_RATE on 8187L in Realtek sources: each bit should be each |
| 803 |
* one of the 12 rates, all are enabled */ |
| 804 |
rtl818x_iowrite16(priv, (__le16 *)0xFF34, 0x0FFF); |
| 805 |
|
| 806 |
reg = rtl818x_ioread8(priv, &priv->map->CW_CONF); |
| 807 |
reg |= RTL818X_CW_CONF_PERPACKET_RETRY; |
| 808 |
rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg); |
| 809 |
|
| 810 |
/* Auto Rate Fallback Register (ARFR): 1M-54M setting */ |
| 811 |
rtl818x_iowrite16_idx(priv, (__le16 *)0xFFE0, 0x0FFF, 1); |
| 812 |
rtl818x_iowrite8_idx(priv, (u8 *)0xFFE2, 0x00, 1); |
| 813 |
|
| 814 |
rtl818x_iowrite16_idx(priv, (__le16 *)0xFFD4, 0xFFFF, 1); |
| 815 |
|
| 816 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, |
| 817 |
RTL818X_EEPROM_CMD_CONFIG); |
| 818 |
reg = rtl818x_ioread8(priv, &priv->map->CONFIG1); |
| 819 |
rtl818x_iowrite8(priv, &priv->map->CONFIG1, (reg & 0x3F) | 0x80); |
| 820 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, |
| 821 |
RTL818X_EEPROM_CMD_NORMAL); |
| 822 |
|
| 823 |
rtl818x_iowrite8(priv, &priv->map->WPA_CONF, 0); |
| 824 |
for (i = 0; i < ARRAY_SIZE(rtl8187b_reg_table); i++) { |
| 825 |
rtl818x_iowrite8_idx(priv, |
| 826 |
(u8 *)(uintptr_t) |
| 827 |
(rtl8187b_reg_table[i][0] | 0xFF00), |
| 828 |
rtl8187b_reg_table[i][1], |
| 829 |
rtl8187b_reg_table[i][2]); |
| 830 |
} |
| 831 |
|
| 832 |
rtl818x_iowrite16(priv, &priv->map->TID_AC_MAP, 0xFA50); |
| 833 |
rtl818x_iowrite16(priv, &priv->map->INT_MIG, 0); |
| 834 |
|
| 835 |
rtl818x_iowrite32_idx(priv, (__le32 *)0xFFF0, 0, 1); |
| 836 |
rtl818x_iowrite32_idx(priv, (__le32 *)0xFFF4, 0, 1); |
| 837 |
rtl818x_iowrite8_idx(priv, (u8 *)0xFFF8, 0, 1); |
| 838 |
|
| 839 |
rtl818x_iowrite32(priv, &priv->map->RF_TIMING, 0x00004001); |
| 840 |
|
| 841 |
/* RFSW_CTRL register */ |
| 842 |
rtl818x_iowrite16_idx(priv, (__le16 *)0xFF72, 0x569A, 2); |
| 843 |
|
| 844 |
rtl818x_iowrite16(priv, &priv->map->RFPinsOutput, 0x0480); |
| 845 |
rtl818x_iowrite16(priv, &priv->map->RFPinsSelect, 0x2488); |
| 846 |
rtl818x_iowrite16(priv, &priv->map->RFPinsEnable, 0x1FFF); |
| 847 |
msleep(100); |
| 848 |
|
| 849 |
priv->rf->init(dev); |
| 850 |
|
| 851 |
reg = RTL818X_CMD_TX_ENABLE | RTL818X_CMD_RX_ENABLE; |
| 852 |
rtl818x_iowrite8(priv, &priv->map->CMD, reg); |
| 853 |
rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF); |
| 854 |
|
| 855 |
rtl818x_iowrite8(priv, (u8 *)0xFE41, 0xF4); |
| 856 |
rtl818x_iowrite8(priv, (u8 *)0xFE40, 0x00); |
| 857 |
rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x00); |
| 858 |
rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x01); |
| 859 |
rtl818x_iowrite8(priv, (u8 *)0xFE40, 0x0F); |
| 860 |
rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x00); |
| 861 |
rtl818x_iowrite8(priv, (u8 *)0xFE42, 0x01); |
| 862 |
|
| 863 |
reg = rtl818x_ioread8(priv, (u8 *)0xFFDB); |
| 864 |
rtl818x_iowrite8(priv, (u8 *)0xFFDB, reg | (1 << 2)); |
| 865 |
rtl818x_iowrite16_idx(priv, (__le16 *)0xFF72, 0x59FA, 3); |
| 866 |
rtl818x_iowrite16_idx(priv, (__le16 *)0xFF74, 0x59D2, 3); |
| 867 |
rtl818x_iowrite16_idx(priv, (__le16 *)0xFF76, 0x59D2, 3); |
| 868 |
rtl818x_iowrite16_idx(priv, (__le16 *)0xFF78, 0x19FA, 3); |
| 869 |
rtl818x_iowrite16_idx(priv, (__le16 *)0xFF7A, 0x19FA, 3); |
| 870 |
rtl818x_iowrite16_idx(priv, (__le16 *)0xFF7C, 0x00D0, 3); |
| 871 |
rtl818x_iowrite8(priv, (u8 *)0xFF61, 0); |
| 872 |
rtl818x_iowrite8_idx(priv, (u8 *)0xFF80, 0x0F, 1); |
| 873 |
rtl818x_iowrite8_idx(priv, (u8 *)0xFF83, 0x03, 1); |
| 874 |
rtl818x_iowrite8(priv, (u8 *)0xFFDA, 0x10); |
| 875 |
rtl818x_iowrite8_idx(priv, (u8 *)0xFF4D, 0x08, 2); |
| 876 |
|
| 877 |
rtl818x_iowrite32(priv, &priv->map->HSSI_PARA, 0x0600321B); |
| 878 |
|
| 879 |
rtl818x_iowrite16_idx(priv, (__le16 *)0xFFEC, 0x0800, 1); |
| 880 |
|
| 881 |
priv->slot_time = 0x9; |
| 882 |
priv->aifsn[0] = 2; /* AIFSN[AC_VO] */ |
| 883 |
priv->aifsn[1] = 2; /* AIFSN[AC_VI] */ |
| 884 |
priv->aifsn[2] = 7; /* AIFSN[AC_BK] */ |
| 885 |
priv->aifsn[3] = 3; /* AIFSN[AC_BE] */ |
| 886 |
rtl818x_iowrite8(priv, &priv->map->ACM_CONTROL, 0); |
| 887 |
|
| 888 |
/* ENEDCA flag must always be set, transmit issues? */ |
| 889 |
rtl818x_iowrite8(priv, &priv->map->MSR, RTL818X_MSR_ENEDCA); |
| 890 |
|
| 891 |
return 0; |
| 892 |
} |
| 893 |
|
| 894 |
static void rtl8187_work(struct work_struct *work) |
| 895 |
{ |
| 896 |
/* The RTL8187 returns the retry count through register 0xFFFA. In |
| 897 |
* addition, it appears to be a cumulative retry count, not the |
| 898 |
* value for the current TX packet. When multiple TX entries are |
| 899 |
* waiting in the queue, the retry count will be the total for all. |
| 900 |
* The "error" may matter for purposes of rate setting, but there is |
| 901 |
* no other choice with this hardware. |
| 902 |
*/ |
| 903 |
struct rtl8187_priv *priv = container_of(work, struct rtl8187_priv, |
| 904 |
work.work); |
| 905 |
struct ieee80211_tx_info *info; |
| 906 |
struct ieee80211_hw *dev = priv->dev; |
| 907 |
static u16 retry; |
| 908 |
u16 tmp; |
| 909 |
u16 avg_retry; |
| 910 |
int length; |
| 911 |
|
| 912 |
mutex_lock(&priv->conf_mutex); |
| 913 |
tmp = rtl818x_ioread16(priv, (__le16 *)0xFFFA); |
| 914 |
length = skb_queue_len(&priv->b_tx_status.queue); |
| 915 |
if (unlikely(!length)) |
| 916 |
length = 1; |
| 917 |
if (unlikely(tmp < retry)) |
| 918 |
tmp = retry; |
| 919 |
avg_retry = (tmp - retry) / length; |
| 920 |
while (skb_queue_len(&priv->b_tx_status.queue) > 0) { |
| 921 |
struct sk_buff *old_skb; |
| 922 |
|
| 923 |
old_skb = skb_dequeue(&priv->b_tx_status.queue); |
| 924 |
info = IEEE80211_SKB_CB(old_skb); |
| 925 |
info->status.rates[0].count = avg_retry + 1; |
| 926 |
if (info->status.rates[0].count > RETRY_COUNT) |
| 927 |
info->flags &= ~IEEE80211_TX_STAT_ACK; |
| 928 |
ieee80211_tx_status_irqsafe(dev, old_skb); |
| 929 |
} |
| 930 |
retry = tmp; |
| 931 |
mutex_unlock(&priv->conf_mutex); |
| 932 |
} |
| 933 |
|
| 934 |
static int rtl8187_start(struct ieee80211_hw *dev) |
| 935 |
{ |
| 936 |
struct rtl8187_priv *priv = dev->priv; |
| 937 |
u32 reg; |
| 938 |
int ret; |
| 939 |
|
| 940 |
mutex_lock(&priv->conf_mutex); |
| 941 |
|
| 942 |
ret = (!priv->is_rtl8187b) ? rtl8187_init_hw(dev) : |
| 943 |
rtl8187b_init_hw(dev); |
| 944 |
if (ret) |
| 945 |
goto rtl8187_start_exit; |
| 946 |
|
| 947 |
init_usb_anchor(&priv->anchored); |
| 948 |
priv->dev = dev; |
| 949 |
|
| 950 |
if (priv->is_rtl8187b) { |
| 951 |
reg = RTL818X_RX_CONF_MGMT | |
| 952 |
RTL818X_RX_CONF_DATA | |
| 953 |
RTL818X_RX_CONF_BROADCAST | |
| 954 |
RTL818X_RX_CONF_NICMAC | |
| 955 |
RTL818X_RX_CONF_BSSID | |
| 956 |
(7 << 13 /* RX FIFO threshold NONE */) | |
| 957 |
(7 << 10 /* MAX RX DMA */) | |
| 958 |
RTL818X_RX_CONF_RX_AUTORESETPHY | |
| 959 |
RTL818X_RX_CONF_ONLYERLPKT; |
| 960 |
priv->rx_conf = reg; |
| 961 |
rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg); |
| 962 |
|
| 963 |
reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL); |
| 964 |
reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN; |
| 965 |
reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL; |
| 966 |
reg &= ~RTL818X_TX_AGC_CTL_FEEDBACK_ANT; |
| 967 |
rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg); |
| 968 |
|
| 969 |
rtl818x_iowrite32(priv, &priv->map->TX_CONF, |
| 970 |
RTL818X_TX_CONF_HW_SEQNUM | |
| 971 |
RTL818X_TX_CONF_DISREQQSIZE | |
| 972 |
(RETRY_COUNT << 8 /* short retry limit */) | |
| 973 |
(RETRY_COUNT << 0 /* long retry limit */) | |
| 974 |
(7 << 21 /* MAX TX DMA */)); |
| 975 |
ret = rtl8187_init_urbs(dev); |
| 976 |
if (ret) |
| 977 |
goto rtl8187_start_exit; |
| 978 |
ret = rtl8187b_init_status_urb(dev); |
| 979 |
if (ret) |
| 980 |
usb_kill_anchored_urbs(&priv->anchored); |
| 981 |
goto rtl8187_start_exit; |
| 982 |
} |
| 983 |
|
| 984 |
rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0xFFFF); |
| 985 |
|
| 986 |
rtl818x_iowrite32(priv, &priv->map->MAR[0], ~0); |
| 987 |
rtl818x_iowrite32(priv, &priv->map->MAR[1], ~0); |
| 988 |
|
| 989 |
ret = rtl8187_init_urbs(dev); |
| 990 |
if (ret) |
| 991 |
goto rtl8187_start_exit; |
| 992 |
|
| 993 |
reg = RTL818X_RX_CONF_ONLYERLPKT | |
| 994 |
RTL818X_RX_CONF_RX_AUTORESETPHY | |
| 995 |
RTL818X_RX_CONF_BSSID | |
| 996 |
RTL818X_RX_CONF_MGMT | |
| 997 |
RTL818X_RX_CONF_DATA | |
| 998 |
(7 << 13 /* RX FIFO threshold NONE */) | |
| 999 |
(7 << 10 /* MAX RX DMA */) | |
| 1000 |
RTL818X_RX_CONF_BROADCAST | |
| 1001 |
RTL818X_RX_CONF_NICMAC; |
| 1002 |
|
| 1003 |
priv->rx_conf = reg; |
| 1004 |
rtl818x_iowrite32(priv, &priv->map->RX_CONF, reg); |
| 1005 |
|
| 1006 |
reg = rtl818x_ioread8(priv, &priv->map->CW_CONF); |
| 1007 |
reg &= ~RTL818X_CW_CONF_PERPACKET_CW; |
| 1008 |
reg |= RTL818X_CW_CONF_PERPACKET_RETRY; |
| 1009 |
rtl818x_iowrite8(priv, &priv->map->CW_CONF, reg); |
| 1010 |
|
| 1011 |
reg = rtl818x_ioread8(priv, &priv->map->TX_AGC_CTL); |
| 1012 |
reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_GAIN; |
| 1013 |
reg &= ~RTL818X_TX_AGC_CTL_PERPACKET_ANTSEL; |
| 1014 |
reg &= ~RTL818X_TX_AGC_CTL_FEEDBACK_ANT; |
| 1015 |
rtl818x_iowrite8(priv, &priv->map->TX_AGC_CTL, reg); |
| 1016 |
|
| 1017 |
reg = RTL818X_TX_CONF_CW_MIN | |
| 1018 |
(7 << 21 /* MAX TX DMA */) | |
| 1019 |
RTL818X_TX_CONF_NO_ICV; |
| 1020 |
rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg); |
| 1021 |
|
| 1022 |
reg = rtl818x_ioread8(priv, &priv->map->CMD); |
| 1023 |
reg |= RTL818X_CMD_TX_ENABLE; |
| 1024 |
reg |= RTL818X_CMD_RX_ENABLE; |
| 1025 |
rtl818x_iowrite8(priv, &priv->map->CMD, reg); |
| 1026 |
INIT_DELAYED_WORK(&priv->work, rtl8187_work); |
| 1027 |
|
| 1028 |
rtl8187_start_exit: |
| 1029 |
mutex_unlock(&priv->conf_mutex); |
| 1030 |
return ret; |
| 1031 |
} |
| 1032 |
|
| 1033 |
static void rtl8187_stop(struct ieee80211_hw *dev, bool suspend) |
| 1034 |
{ |
| 1035 |
struct rtl8187_priv *priv = dev->priv; |
| 1036 |
struct sk_buff *skb; |
| 1037 |
u32 reg; |
| 1038 |
|
| 1039 |
mutex_lock(&priv->conf_mutex); |
| 1040 |
rtl818x_iowrite16(priv, &priv->map->INT_MASK, 0); |
| 1041 |
|
| 1042 |
reg = rtl818x_ioread8(priv, &priv->map->CMD); |
| 1043 |
reg &= ~RTL818X_CMD_TX_ENABLE; |
| 1044 |
reg &= ~RTL818X_CMD_RX_ENABLE; |
| 1045 |
rtl818x_iowrite8(priv, &priv->map->CMD, reg); |
| 1046 |
|
| 1047 |
priv->rf->stop(dev); |
| 1048 |
rtl8187_set_anaparam(priv, false); |
| 1049 |
|
| 1050 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); |
| 1051 |
reg = rtl818x_ioread8(priv, &priv->map->CONFIG4); |
| 1052 |
rtl818x_iowrite8(priv, &priv->map->CONFIG4, reg | RTL818X_CONFIG4_VCOOFF); |
| 1053 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); |
| 1054 |
|
| 1055 |
usb_kill_anchored_urbs(&priv->anchored); |
| 1056 |
|
| 1057 |
while ((skb = skb_dequeue(&priv->b_tx_status.queue))) |
| 1058 |
dev_kfree_skb_any(skb); |
| 1059 |
|
| 1060 |
mutex_unlock(&priv->conf_mutex); |
| 1061 |
|
| 1062 |
if (!priv->is_rtl8187b) |
| 1063 |
cancel_delayed_work_sync(&priv->work); |
| 1064 |
} |
| 1065 |
|
| 1066 |
static u64 rtl8187_get_tsf(struct ieee80211_hw *dev, struct ieee80211_vif *vif) |
| 1067 |
{ |
| 1068 |
struct rtl8187_priv *priv = dev->priv; |
| 1069 |
|
| 1070 |
return rtl818x_ioread32(priv, &priv->map->TSFT[0]) | |
| 1071 |
(u64)(rtl818x_ioread32(priv, &priv->map->TSFT[1])) << 32; |
| 1072 |
} |
| 1073 |
|
| 1074 |
|
| 1075 |
static void rtl8187_beacon_work(struct work_struct *work) |
| 1076 |
{ |
| 1077 |
struct rtl8187_vif *vif_priv = |
| 1078 |
container_of(work, struct rtl8187_vif, beacon_work.work); |
| 1079 |
struct ieee80211_vif *vif = |
| 1080 |
container_of((void *)vif_priv, struct ieee80211_vif, drv_priv); |
| 1081 |
struct ieee80211_hw *dev = vif_priv->dev; |
| 1082 |
struct ieee80211_mgmt *mgmt; |
| 1083 |
struct sk_buff *skb; |
| 1084 |
|
| 1085 |
/* don't overflow the tx ring */ |
| 1086 |
if (ieee80211_queue_stopped(dev, 0)) |
| 1087 |
goto resched; |
| 1088 |
|
| 1089 |
/* grab a fresh beacon */ |
| 1090 |
skb = ieee80211_beacon_get(dev, vif, 0); |
| 1091 |
if (!skb) |
| 1092 |
goto resched; |
| 1093 |
|
| 1094 |
/* |
| 1095 |
* update beacon timestamp w/ TSF value |
| 1096 |
* TODO: make hardware update beacon timestamp |
| 1097 |
*/ |
| 1098 |
mgmt = (struct ieee80211_mgmt *)skb->data; |
| 1099 |
mgmt->u.beacon.timestamp = cpu_to_le64(rtl8187_get_tsf(dev, vif)); |
| 1100 |
|
| 1101 |
/* TODO: use actual beacon queue */ |
| 1102 |
skb_set_queue_mapping(skb, 0); |
| 1103 |
|
| 1104 |
rtl8187_tx(dev, NULL, skb); |
| 1105 |
|
| 1106 |
resched: |
| 1107 |
/* |
| 1108 |
* schedule next beacon |
| 1109 |
* TODO: use hardware support for beacon timing |
| 1110 |
*/ |
| 1111 |
schedule_delayed_work(&vif_priv->beacon_work, |
| 1112 |
usecs_to_jiffies(1024 * vif->bss_conf.beacon_int)); |
| 1113 |
} |
| 1114 |
|
| 1115 |
|
| 1116 |
static int rtl8187_add_interface(struct ieee80211_hw *dev, |
| 1117 |
struct ieee80211_vif *vif) |
| 1118 |
{ |
| 1119 |
struct rtl8187_priv *priv = dev->priv; |
| 1120 |
struct rtl8187_vif *vif_priv; |
| 1121 |
int i; |
| 1122 |
int ret = -EOPNOTSUPP; |
| 1123 |
|
| 1124 |
mutex_lock(&priv->conf_mutex); |
| 1125 |
if (priv->vif) |
| 1126 |
goto exit; |
| 1127 |
|
| 1128 |
switch (vif->type) { |
| 1129 |
case NL80211_IFTYPE_STATION: |
| 1130 |
case NL80211_IFTYPE_ADHOC: |
| 1131 |
break; |
| 1132 |
default: |
| 1133 |
goto exit; |
| 1134 |
} |
| 1135 |
|
| 1136 |
ret = 0; |
| 1137 |
priv->vif = vif; |
| 1138 |
|
| 1139 |
/* Initialize driver private area */ |
| 1140 |
vif_priv = (struct rtl8187_vif *)&vif->drv_priv; |
| 1141 |
vif_priv->dev = dev; |
| 1142 |
INIT_DELAYED_WORK(&vif_priv->beacon_work, rtl8187_beacon_work); |
| 1143 |
vif_priv->enable_beacon = false; |
| 1144 |
|
| 1145 |
|
| 1146 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); |
| 1147 |
for (i = 0; i < ETH_ALEN; i++) |
| 1148 |
rtl818x_iowrite8(priv, &priv->map->MAC[i], |
| 1149 |
((u8 *)vif->addr)[i]); |
| 1150 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); |
| 1151 |
|
| 1152 |
exit: |
| 1153 |
mutex_unlock(&priv->conf_mutex); |
| 1154 |
return ret; |
| 1155 |
} |
| 1156 |
|
| 1157 |
static void rtl8187_remove_interface(struct ieee80211_hw *dev, |
| 1158 |
struct ieee80211_vif *vif) |
| 1159 |
{ |
| 1160 |
struct rtl8187_priv *priv = dev->priv; |
| 1161 |
mutex_lock(&priv->conf_mutex); |
| 1162 |
priv->vif = NULL; |
| 1163 |
mutex_unlock(&priv->conf_mutex); |
| 1164 |
} |
| 1165 |
|
| 1166 |
static int rtl8187_config(struct ieee80211_hw *dev, int radio_idx, u32 changed) |
| 1167 |
{ |
| 1168 |
struct rtl8187_priv *priv = dev->priv; |
| 1169 |
struct ieee80211_conf *conf = &dev->conf; |
| 1170 |
u32 reg; |
| 1171 |
|
| 1172 |
mutex_lock(&priv->conf_mutex); |
| 1173 |
reg = rtl818x_ioread32(priv, &priv->map->TX_CONF); |
| 1174 |
/* Enable TX loopback on MAC level to avoid TX during channel |
| 1175 |
* changes, as this has be seen to causes problems and the |
| 1176 |
* card will stop work until next reset |
| 1177 |
*/ |
| 1178 |
rtl818x_iowrite32(priv, &priv->map->TX_CONF, |
| 1179 |
reg | RTL818X_TX_CONF_LOOPBACK_MAC); |
| 1180 |
priv->rf->set_chan(dev, conf); |
| 1181 |
msleep(10); |
| 1182 |
rtl818x_iowrite32(priv, &priv->map->TX_CONF, reg); |
| 1183 |
|
| 1184 |
rtl818x_iowrite16(priv, &priv->map->ATIM_WND, 2); |
| 1185 |
rtl818x_iowrite16(priv, &priv->map->ATIMTR_INTERVAL, 100); |
| 1186 |
rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL, 100); |
| 1187 |
rtl818x_iowrite16(priv, &priv->map->BEACON_INTERVAL_TIME, 100); |
| 1188 |
mutex_unlock(&priv->conf_mutex); |
| 1189 |
return 0; |
| 1190 |
} |
| 1191 |
|
| 1192 |
/* |
| 1193 |
* With 8187B, AC_*_PARAM clashes with FEMR definition in struct rtl818x_csr for |
| 1194 |
* example. Thus we have to use raw values for AC_*_PARAM register addresses. |
| 1195 |
*/ |
| 1196 |
static __le32 *rtl8187b_ac_addr[4] = { |
| 1197 |
(__le32 *) 0xFFF0, /* AC_VO */ |
| 1198 |
(__le32 *) 0xFFF4, /* AC_VI */ |
| 1199 |
(__le32 *) 0xFFFC, /* AC_BK */ |
| 1200 |
(__le32 *) 0xFFF8, /* AC_BE */ |
| 1201 |
}; |
| 1202 |
|
| 1203 |
#define SIFS_TIME 0xa |
| 1204 |
|
| 1205 |
static void rtl8187_conf_erp(struct rtl8187_priv *priv, bool use_short_slot, |
| 1206 |
bool use_short_preamble) |
| 1207 |
{ |
| 1208 |
if (priv->is_rtl8187b) { |
| 1209 |
u8 difs, eifs; |
| 1210 |
u16 ack_timeout; |
| 1211 |
int queue; |
| 1212 |
|
| 1213 |
if (use_short_slot) { |
| 1214 |
priv->slot_time = 0x9; |
| 1215 |
difs = 0x1c; |
| 1216 |
eifs = 0x53; |
| 1217 |
} else { |
| 1218 |
priv->slot_time = 0x14; |
| 1219 |
difs = 0x32; |
| 1220 |
eifs = 0x5b; |
| 1221 |
} |
| 1222 |
rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22); |
| 1223 |
rtl818x_iowrite8(priv, &priv->map->SLOT, priv->slot_time); |
| 1224 |
rtl818x_iowrite8(priv, &priv->map->DIFS, difs); |
| 1225 |
|
| 1226 |
/* |
| 1227 |
* BRSR+1 on 8187B is in fact EIFS register |
| 1228 |
* Value in units of 4 us |
| 1229 |
*/ |
| 1230 |
rtl818x_iowrite8(priv, (u8 *)&priv->map->BRSR + 1, eifs); |
| 1231 |
|
| 1232 |
/* |
| 1233 |
* For 8187B, CARRIER_SENSE_COUNTER is in fact ack timeout |
| 1234 |
* register. In units of 4 us like eifs register |
| 1235 |
* ack_timeout = ack duration + plcp + difs + preamble |
| 1236 |
*/ |
| 1237 |
ack_timeout = 112 + 48 + difs; |
| 1238 |
if (use_short_preamble) |
| 1239 |
ack_timeout += 72; |
| 1240 |
else |
| 1241 |
ack_timeout += 144; |
| 1242 |
rtl818x_iowrite8(priv, &priv->map->CARRIER_SENSE_COUNTER, |
| 1243 |
DIV_ROUND_UP(ack_timeout, 4)); |
| 1244 |
|
| 1245 |
for (queue = 0; queue < 4; queue++) |
| 1246 |
rtl818x_iowrite8(priv, (u8 *) rtl8187b_ac_addr[queue], |
| 1247 |
priv->aifsn[queue] * priv->slot_time + |
| 1248 |
SIFS_TIME); |
| 1249 |
} else { |
| 1250 |
rtl818x_iowrite8(priv, &priv->map->SIFS, 0x22); |
| 1251 |
if (use_short_slot) { |
| 1252 |
rtl818x_iowrite8(priv, &priv->map->SLOT, 0x9); |
| 1253 |
rtl818x_iowrite8(priv, &priv->map->DIFS, 0x14); |
| 1254 |
rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x14); |
| 1255 |
} else { |
| 1256 |
rtl818x_iowrite8(priv, &priv->map->SLOT, 0x14); |
| 1257 |
rtl818x_iowrite8(priv, &priv->map->DIFS, 0x24); |
| 1258 |
rtl818x_iowrite8(priv, &priv->map->EIFS, 91 - 0x24); |
| 1259 |
} |
| 1260 |
} |
| 1261 |
} |
| 1262 |
|
| 1263 |
static void rtl8187_bss_info_changed(struct ieee80211_hw *dev, |
| 1264 |
struct ieee80211_vif *vif, |
| 1265 |
struct ieee80211_bss_conf *info, |
| 1266 |
u64 changed) |
| 1267 |
{ |
| 1268 |
struct rtl8187_priv *priv = dev->priv; |
| 1269 |
struct rtl8187_vif *vif_priv; |
| 1270 |
int i; |
| 1271 |
u8 reg; |
| 1272 |
|
| 1273 |
vif_priv = (struct rtl8187_vif *)&vif->drv_priv; |
| 1274 |
|
| 1275 |
if (changed & BSS_CHANGED_BSSID) { |
| 1276 |
mutex_lock(&priv->conf_mutex); |
| 1277 |
for (i = 0; i < ETH_ALEN; i++) |
| 1278 |
rtl818x_iowrite8(priv, &priv->map->BSSID[i], |
| 1279 |
info->bssid[i]); |
| 1280 |
|
| 1281 |
if (priv->is_rtl8187b) |
| 1282 |
reg = RTL818X_MSR_ENEDCA; |
| 1283 |
else |
| 1284 |
reg = 0; |
| 1285 |
|
| 1286 |
if (is_valid_ether_addr(info->bssid)) { |
| 1287 |
if (vif->type == NL80211_IFTYPE_ADHOC) |
| 1288 |
reg |= RTL818X_MSR_ADHOC; |
| 1289 |
else |
| 1290 |
reg |= RTL818X_MSR_INFRA; |
| 1291 |
} |
| 1292 |
else |
| 1293 |
reg |= RTL818X_MSR_NO_LINK; |
| 1294 |
|
| 1295 |
rtl818x_iowrite8(priv, &priv->map->MSR, reg); |
| 1296 |
|
| 1297 |
mutex_unlock(&priv->conf_mutex); |
| 1298 |
} |
| 1299 |
|
| 1300 |
if (changed & (BSS_CHANGED_ERP_SLOT | BSS_CHANGED_ERP_PREAMBLE)) |
| 1301 |
rtl8187_conf_erp(priv, info->use_short_slot, |
| 1302 |
info->use_short_preamble); |
| 1303 |
|
| 1304 |
if (changed & BSS_CHANGED_BEACON_ENABLED) |
| 1305 |
vif_priv->enable_beacon = info->enable_beacon; |
| 1306 |
|
| 1307 |
if (changed & (BSS_CHANGED_BEACON_ENABLED | BSS_CHANGED_BEACON)) { |
| 1308 |
cancel_delayed_work_sync(&vif_priv->beacon_work); |
| 1309 |
if (vif_priv->enable_beacon) |
| 1310 |
schedule_work(&vif_priv->beacon_work.work); |
| 1311 |
} |
| 1312 |
|
| 1313 |
} |
| 1314 |
|
| 1315 |
static u64 rtl8187_prepare_multicast(struct ieee80211_hw *dev, |
| 1316 |
struct netdev_hw_addr_list *mc_list) |
| 1317 |
{ |
| 1318 |
return netdev_hw_addr_list_count(mc_list); |
| 1319 |
} |
| 1320 |
|
| 1321 |
static void rtl8187_configure_filter(struct ieee80211_hw *dev, |
| 1322 |
unsigned int changed_flags, |
| 1323 |
unsigned int *total_flags, |
| 1324 |
u64 multicast) |
| 1325 |
{ |
| 1326 |
struct rtl8187_priv *priv = dev->priv; |
| 1327 |
|
| 1328 |
if (changed_flags & FIF_FCSFAIL) |
| 1329 |
priv->rx_conf ^= RTL818X_RX_CONF_FCS; |
| 1330 |
if (changed_flags & FIF_CONTROL) |
| 1331 |
priv->rx_conf ^= RTL818X_RX_CONF_CTRL; |
| 1332 |
if (*total_flags & FIF_OTHER_BSS || |
| 1333 |
*total_flags & FIF_ALLMULTI || multicast > 0) |
| 1334 |
priv->rx_conf |= RTL818X_RX_CONF_MONITOR; |
| 1335 |
else |
| 1336 |
priv->rx_conf &= ~RTL818X_RX_CONF_MONITOR; |
| 1337 |
|
| 1338 |
*total_flags = 0; |
| 1339 |
|
| 1340 |
if (priv->rx_conf & RTL818X_RX_CONF_FCS) |
| 1341 |
*total_flags |= FIF_FCSFAIL; |
| 1342 |
if (priv->rx_conf & RTL818X_RX_CONF_CTRL) |
| 1343 |
*total_flags |= FIF_CONTROL; |
| 1344 |
if (priv->rx_conf & RTL818X_RX_CONF_MONITOR) { |
| 1345 |
*total_flags |= FIF_OTHER_BSS; |
| 1346 |
*total_flags |= FIF_ALLMULTI; |
| 1347 |
} |
| 1348 |
|
| 1349 |
rtl818x_iowrite32_async(priv, &priv->map->RX_CONF, priv->rx_conf); |
| 1350 |
} |
| 1351 |
|
| 1352 |
static int rtl8187_conf_tx(struct ieee80211_hw *dev, |
| 1353 |
struct ieee80211_vif *vif, |
| 1354 |
unsigned int link_id, u16 queue, |
| 1355 |
const struct ieee80211_tx_queue_params *params) |
| 1356 |
{ |
| 1357 |
struct rtl8187_priv *priv = dev->priv; |
| 1358 |
u8 cw_min, cw_max; |
| 1359 |
|
| 1360 |
if (queue > 3) |
| 1361 |
return -EINVAL; |
| 1362 |
|
| 1363 |
cw_min = fls(params->cw_min); |
| 1364 |
cw_max = fls(params->cw_max); |
| 1365 |
|
| 1366 |
if (priv->is_rtl8187b) { |
| 1367 |
priv->aifsn[queue] = params->aifs; |
| 1368 |
|
| 1369 |
/* |
| 1370 |
* This is the structure of AC_*_PARAM registers in 8187B: |
| 1371 |
* - TXOP limit field, bit offset = 16 |
| 1372 |
* - ECWmax, bit offset = 12 |
| 1373 |
* - ECWmin, bit offset = 8 |
| 1374 |
* - AIFS, bit offset = 0 |
| 1375 |
*/ |
| 1376 |
rtl818x_iowrite32(priv, rtl8187b_ac_addr[queue], |
| 1377 |
(params->txop << 16) | (cw_max << 12) | |
| 1378 |
(cw_min << 8) | (params->aifs * |
| 1379 |
priv->slot_time + SIFS_TIME)); |
| 1380 |
} else { |
| 1381 |
if (queue != 0) |
| 1382 |
return -EINVAL; |
| 1383 |
|
| 1384 |
rtl818x_iowrite8(priv, &priv->map->CW_VAL, |
| 1385 |
cw_min | (cw_max << 4)); |
| 1386 |
} |
| 1387 |
return 0; |
| 1388 |
} |
| 1389 |
|
| 1390 |
|
| 1391 |
static const struct ieee80211_ops rtl8187_ops = { |
| 1392 |
.add_chanctx = ieee80211_emulate_add_chanctx, |
| 1393 |
.remove_chanctx = ieee80211_emulate_remove_chanctx, |
| 1394 |
.change_chanctx = ieee80211_emulate_change_chanctx, |
| 1395 |
.switch_vif_chanctx = ieee80211_emulate_switch_vif_chanctx, |
| 1396 |
.tx = rtl8187_tx, |
| 1397 |
.wake_tx_queue = ieee80211_handle_wake_tx_queue, |
| 1398 |
.start = rtl8187_start, |
| 1399 |
.stop = rtl8187_stop, |
| 1400 |
.add_interface = rtl8187_add_interface, |
| 1401 |
.remove_interface = rtl8187_remove_interface, |
| 1402 |
.config = rtl8187_config, |
| 1403 |
.bss_info_changed = rtl8187_bss_info_changed, |
| 1404 |
.prepare_multicast = rtl8187_prepare_multicast, |
| 1405 |
.configure_filter = rtl8187_configure_filter, |
| 1406 |
.conf_tx = rtl8187_conf_tx, |
| 1407 |
.rfkill_poll = rtl8187_rfkill_poll, |
| 1408 |
.get_tsf = rtl8187_get_tsf, |
| 1409 |
}; |
| 1410 |
|
| 1411 |
static void rtl8187_eeprom_register_read(struct eeprom_93cx6 *eeprom) |
| 1412 |
{ |
| 1413 |
struct ieee80211_hw *dev = eeprom->data; |
| 1414 |
struct rtl8187_priv *priv = dev->priv; |
| 1415 |
u8 reg = rtl818x_ioread8(priv, &priv->map->EEPROM_CMD); |
| 1416 |
|
| 1417 |
eeprom->reg_data_in = reg & RTL818X_EEPROM_CMD_WRITE; |
| 1418 |
eeprom->reg_data_out = reg & RTL818X_EEPROM_CMD_READ; |
| 1419 |
eeprom->reg_data_clock = reg & RTL818X_EEPROM_CMD_CK; |
| 1420 |
eeprom->reg_chip_select = reg & RTL818X_EEPROM_CMD_CS; |
| 1421 |
} |
| 1422 |
|
| 1423 |
static void rtl8187_eeprom_register_write(struct eeprom_93cx6 *eeprom) |
| 1424 |
{ |
| 1425 |
struct ieee80211_hw *dev = eeprom->data; |
| 1426 |
struct rtl8187_priv *priv = dev->priv; |
| 1427 |
u8 reg = RTL818X_EEPROM_CMD_PROGRAM; |
| 1428 |
|
| 1429 |
if (eeprom->reg_data_in) |
| 1430 |
reg |= RTL818X_EEPROM_CMD_WRITE; |
| 1431 |
if (eeprom->reg_data_out) |
| 1432 |
reg |= RTL818X_EEPROM_CMD_READ; |
| 1433 |
if (eeprom->reg_data_clock) |
| 1434 |
reg |= RTL818X_EEPROM_CMD_CK; |
| 1435 |
if (eeprom->reg_chip_select) |
| 1436 |
reg |= RTL818X_EEPROM_CMD_CS; |
| 1437 |
|
| 1438 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, reg); |
| 1439 |
udelay(10); |
| 1440 |
} |
| 1441 |
|
| 1442 |
static int rtl8187_probe(struct usb_interface *intf, |
| 1443 |
const struct usb_device_id *id) |
| 1444 |
{ |
| 1445 |
struct usb_device *udev = interface_to_usbdev(intf); |
| 1446 |
struct ieee80211_hw *dev; |
| 1447 |
struct rtl8187_priv *priv; |
| 1448 |
struct eeprom_93cx6 eeprom; |
| 1449 |
struct ieee80211_channel *channel; |
| 1450 |
const char *chip_name; |
| 1451 |
u16 txpwr, reg; |
| 1452 |
u16 product_id = le16_to_cpu(udev->descriptor.idProduct); |
| 1453 |
int err, i; |
| 1454 |
u8 mac_addr[ETH_ALEN]; |
| 1455 |
|
| 1456 |
dev = ieee80211_alloc_hw(sizeof(*priv), &rtl8187_ops); |
| 1457 |
if (!dev) { |
| 1458 |
printk(KERN_ERR "rtl8187: ieee80211 alloc failed\n"); |
| 1459 |
return -ENOMEM; |
| 1460 |
} |
| 1461 |
|
| 1462 |
priv = dev->priv; |
| 1463 |
priv->is_rtl8187b = (id->driver_info == DEVICE_RTL8187B); |
| 1464 |
|
| 1465 |
/* allocate "DMA aware" buffer for register accesses */ |
| 1466 |
priv->io_dmabuf = kmalloc_obj(*priv->io_dmabuf); |
| 1467 |
if (!priv->io_dmabuf) { |
| 1468 |
err = -ENOMEM; |
| 1469 |
goto err_free_dev; |
| 1470 |
} |
| 1471 |
mutex_init(&priv->io_mutex); |
| 1472 |
mutex_init(&priv->conf_mutex); |
| 1473 |
|
| 1474 |
SET_IEEE80211_DEV(dev, &intf->dev); |
| 1475 |
usb_set_intfdata(intf, dev); |
| 1476 |
priv->udev = udev; |
| 1477 |
|
| 1478 |
usb_get_dev(udev); |
| 1479 |
|
| 1480 |
skb_queue_head_init(&priv->rx_queue); |
| 1481 |
|
| 1482 |
BUILD_BUG_ON(sizeof(priv->channels) != sizeof(rtl818x_channels)); |
| 1483 |
BUILD_BUG_ON(sizeof(priv->rates) != sizeof(rtl818x_rates)); |
| 1484 |
|
| 1485 |
memcpy(priv->channels, rtl818x_channels, sizeof(rtl818x_channels)); |
| 1486 |
memcpy(priv->rates, rtl818x_rates, sizeof(rtl818x_rates)); |
| 1487 |
priv->map = (struct rtl818x_csr *)0xFF00; |
| 1488 |
|
| 1489 |
priv->band.band = NL80211_BAND_2GHZ; |
| 1490 |
priv->band.channels = priv->channels; |
| 1491 |
priv->band.n_channels = ARRAY_SIZE(rtl818x_channels); |
| 1492 |
priv->band.bitrates = priv->rates; |
| 1493 |
priv->band.n_bitrates = ARRAY_SIZE(rtl818x_rates); |
| 1494 |
dev->wiphy->bands[NL80211_BAND_2GHZ] = &priv->band; |
| 1495 |
|
| 1496 |
|
| 1497 |
ieee80211_hw_set(dev, RX_INCLUDES_FCS); |
| 1498 |
ieee80211_hw_set(dev, HOST_BROADCAST_PS_BUFFERING); |
| 1499 |
ieee80211_hw_set(dev, SIGNAL_DBM); |
| 1500 |
/* Initialize rate-control variables */ |
| 1501 |
dev->max_rates = 1; |
| 1502 |
dev->max_rate_tries = RETRY_COUNT; |
| 1503 |
|
| 1504 |
eeprom.data = dev; |
| 1505 |
eeprom.register_read = rtl8187_eeprom_register_read; |
| 1506 |
eeprom.register_write = rtl8187_eeprom_register_write; |
| 1507 |
if (rtl818x_ioread32(priv, &priv->map->RX_CONF) & (1 << 6)) |
| 1508 |
eeprom.width = PCI_EEPROM_WIDTH_93C66; |
| 1509 |
else |
| 1510 |
eeprom.width = PCI_EEPROM_WIDTH_93C46; |
| 1511 |
|
| 1512 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_CONFIG); |
| 1513 |
udelay(10); |
| 1514 |
|
| 1515 |
eeprom_93cx6_multiread(&eeprom, RTL8187_EEPROM_MAC_ADDR, |
| 1516 |
(__le16 __force *)mac_addr, 3); |
| 1517 |
if (!is_valid_ether_addr(mac_addr)) { |
| 1518 |
printk(KERN_WARNING "rtl8187: Invalid hwaddr! Using randomly " |
| 1519 |
"generated MAC address\n"); |
| 1520 |
eth_random_addr(mac_addr); |
| 1521 |
} |
| 1522 |
SET_IEEE80211_PERM_ADDR(dev, mac_addr); |
| 1523 |
|
| 1524 |
channel = priv->channels; |
| 1525 |
for (i = 0; i < 3; i++) { |
| 1526 |
eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_1 + i, |
| 1527 |
&txpwr); |
| 1528 |
(*channel++).hw_value = txpwr & 0xFF; |
| 1529 |
(*channel++).hw_value = txpwr >> 8; |
| 1530 |
} |
| 1531 |
for (i = 0; i < 2; i++) { |
| 1532 |
eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_4 + i, |
| 1533 |
&txpwr); |
| 1534 |
(*channel++).hw_value = txpwr & 0xFF; |
| 1535 |
(*channel++).hw_value = txpwr >> 8; |
| 1536 |
} |
| 1537 |
|
| 1538 |
eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_BASE, |
| 1539 |
&priv->txpwr_base); |
| 1540 |
|
| 1541 |
reg = rtl818x_ioread8(priv, &priv->map->PGSELECT) & ~1; |
| 1542 |
rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg | 1); |
| 1543 |
/* 0 means asic B-cut, we should use SW 3 wire |
| 1544 |
* bit-by-bit banging for radio. 1 means we can use |
| 1545 |
* USB specific request to write radio registers */ |
| 1546 |
priv->asic_rev = rtl818x_ioread8(priv, (u8 *)0xFFFE) & 0x3; |
| 1547 |
rtl818x_iowrite8(priv, &priv->map->PGSELECT, reg); |
| 1548 |
rtl818x_iowrite8(priv, &priv->map->EEPROM_CMD, RTL818X_EEPROM_CMD_NORMAL); |
| 1549 |
|
| 1550 |
if (!priv->is_rtl8187b) { |
| 1551 |
u32 reg32; |
| 1552 |
reg32 = rtl818x_ioread32(priv, &priv->map->TX_CONF); |
| 1553 |
reg32 &= RTL818X_TX_CONF_HWVER_MASK; |
| 1554 |
switch (reg32) { |
| 1555 |
case RTL818X_TX_CONF_R8187vD_B: |
| 1556 |
/* Some RTL8187B devices have a USB ID of 0x8187 |
| 1557 |
* detect them here */ |
| 1558 |
chip_name = "RTL8187BvB(early)"; |
| 1559 |
priv->is_rtl8187b = 1; |
| 1560 |
priv->hw_rev = RTL8187BvB; |
| 1561 |
break; |
| 1562 |
case RTL818X_TX_CONF_R8187vD: |
| 1563 |
chip_name = "RTL8187vD"; |
| 1564 |
break; |
| 1565 |
default: |
| 1566 |
chip_name = "RTL8187vB (default)"; |
| 1567 |
} |
| 1568 |
} else { |
| 1569 |
/* |
| 1570 |
* Force USB request to write radio registers for 8187B, Realtek |
| 1571 |
* only uses it in their sources |
| 1572 |
*/ |
| 1573 |
/*if (priv->asic_rev == 0) { |
| 1574 |
printk(KERN_WARNING "rtl8187: Forcing use of USB " |
| 1575 |
"requests to write to radio registers\n"); |
| 1576 |
priv->asic_rev = 1; |
| 1577 |
}*/ |
| 1578 |
switch (rtl818x_ioread8(priv, (u8 *)0xFFE1)) { |
| 1579 |
case RTL818X_R8187B_B: |
| 1580 |
chip_name = "RTL8187BvB"; |
| 1581 |
priv->hw_rev = RTL8187BvB; |
| 1582 |
break; |
| 1583 |
case RTL818X_R8187B_D: |
| 1584 |
chip_name = "RTL8187BvD"; |
| 1585 |
priv->hw_rev = RTL8187BvD; |
| 1586 |
break; |
| 1587 |
case RTL818X_R8187B_E: |
| 1588 |
chip_name = "RTL8187BvE"; |
| 1589 |
priv->hw_rev = RTL8187BvE; |
| 1590 |
break; |
| 1591 |
default: |
| 1592 |
chip_name = "RTL8187BvB (default)"; |
| 1593 |
priv->hw_rev = RTL8187BvB; |
| 1594 |
} |
| 1595 |
} |
| 1596 |
|
| 1597 |
if (!priv->is_rtl8187b) { |
| 1598 |
for (i = 0; i < 2; i++) { |
| 1599 |
eeprom_93cx6_read(&eeprom, |
| 1600 |
RTL8187_EEPROM_TXPWR_CHAN_6 + i, |
| 1601 |
&txpwr); |
| 1602 |
(*channel++).hw_value = txpwr & 0xFF; |
| 1603 |
(*channel++).hw_value = txpwr >> 8; |
| 1604 |
} |
| 1605 |
} else { |
| 1606 |
eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_TXPWR_CHAN_6, |
| 1607 |
&txpwr); |
| 1608 |
(*channel++).hw_value = txpwr & 0xFF; |
| 1609 |
|
| 1610 |
eeprom_93cx6_read(&eeprom, 0x0A, &txpwr); |
| 1611 |
(*channel++).hw_value = txpwr & 0xFF; |
| 1612 |
|
| 1613 |
eeprom_93cx6_read(&eeprom, 0x1C, &txpwr); |
| 1614 |
(*channel++).hw_value = txpwr & 0xFF; |
| 1615 |
(*channel++).hw_value = txpwr >> 8; |
| 1616 |
} |
| 1617 |
/* Handle the differing rfkill GPIO bit in different models */ |
| 1618 |
priv->rfkill_mask = RFKILL_MASK_8187_89_97; |
| 1619 |
if (product_id == 0x8197 || product_id == 0x8198) { |
| 1620 |
eeprom_93cx6_read(&eeprom, RTL8187_EEPROM_SELECT_GPIO, ®); |
| 1621 |
if (reg & 0xFF00) |
| 1622 |
priv->rfkill_mask = RFKILL_MASK_8198; |
| 1623 |
} |
| 1624 |
dev->vif_data_size = sizeof(struct rtl8187_vif); |
| 1625 |
dev->wiphy->interface_modes = BIT(NL80211_IFTYPE_STATION) | |
| 1626 |
BIT(NL80211_IFTYPE_ADHOC) ; |
| 1627 |
|
| 1628 |
wiphy_ext_feature_set(dev->wiphy, NL80211_EXT_FEATURE_CQM_RSSI_LIST); |
| 1629 |
|
| 1630 |
if ((id->driver_info == DEVICE_RTL8187) && priv->is_rtl8187b) |
| 1631 |
printk(KERN_INFO "rtl8187: inconsistency between id with OEM" |
| 1632 |
" info!\n"); |
| 1633 |
|
| 1634 |
priv->rf = rtl8187_detect_rf(dev); |
| 1635 |
dev->extra_tx_headroom = (!priv->is_rtl8187b) ? |
| 1636 |
sizeof(struct rtl8187_tx_hdr) : |
| 1637 |
sizeof(struct rtl8187b_tx_hdr); |
| 1638 |
if (!priv->is_rtl8187b) |
| 1639 |
dev->queues = 1; |
| 1640 |
else |
| 1641 |
dev->queues = 4; |
| 1642 |
|
| 1643 |
err = ieee80211_register_hw(dev); |
| 1644 |
if (err) { |
| 1645 |
printk(KERN_ERR "rtl8187: Cannot register device\n"); |
| 1646 |
goto err_free_dmabuf; |
| 1647 |
} |
| 1648 |
skb_queue_head_init(&priv->b_tx_status.queue); |
| 1649 |
|
| 1650 |
wiphy_info(dev->wiphy, "hwaddr %pM, %s V%d + %s, rfkill mask %d\n", |
| 1651 |
mac_addr, chip_name, priv->asic_rev, priv->rf->name, |
| 1652 |
priv->rfkill_mask); |
| 1653 |
|
| 1654 |
#ifdef CONFIG_RTL8187_LEDS |
| 1655 |
eeprom_93cx6_read(&eeprom, 0x3F, ®); |
| 1656 |
reg &= 0xFF; |
| 1657 |
rtl8187_leds_init(dev, reg); |
| 1658 |
#endif |
| 1659 |
rtl8187_rfkill_init(dev); |
| 1660 |
|
| 1661 |
return 0; |
| 1662 |
|
| 1663 |
err_free_dmabuf: |
| 1664 |
kfree(priv->io_dmabuf); |
| 1665 |
usb_set_intfdata(intf, NULL); |
| 1666 |
usb_put_dev(udev); |
| 1667 |
err_free_dev: |
| 1668 |
ieee80211_free_hw(dev); |
| 1669 |
return err; |
| 1670 |
} |
| 1671 |
|
| 1672 |
static void rtl8187_disconnect(struct usb_interface *intf) |
| 1673 |
{ |
| 1674 |
struct ieee80211_hw *dev = usb_get_intfdata(intf); |
| 1675 |
struct rtl8187_priv *priv; |
| 1676 |
|
| 1677 |
if (!dev) |
| 1678 |
return; |
| 1679 |
|
| 1680 |
#ifdef CONFIG_RTL8187_LEDS |
| 1681 |
rtl8187_leds_exit(dev); |
| 1682 |
#endif |
| 1683 |
rtl8187_rfkill_exit(dev); |
| 1684 |
ieee80211_unregister_hw(dev); |
| 1685 |
|
| 1686 |
priv = dev->priv; |
| 1687 |
usb_reset_device(priv->udev); |
| 1688 |
usb_put_dev(interface_to_usbdev(intf)); |
| 1689 |
kfree(priv->io_dmabuf); |
| 1690 |
ieee80211_free_hw(dev); |
| 1691 |
} |
| 1692 |
|
| 1693 |
static struct usb_driver rtl8187_driver = { |
| 1694 |
.name = KBUILD_MODNAME, |
| 1695 |
.id_table = rtl8187_table, |
| 1696 |
.probe = rtl8187_probe, |
| 1697 |
.disconnect = rtl8187_disconnect, |
| 1698 |
.disable_hub_initiated_lpm = 1, |
| 1699 |
}; |
| 1700 |
|
| 1701 |
module_usb_driver(rtl8187_driver); |