| 1 |
// SPDX-License-Identifier: GPL-2.0-only |
| 2 |
/****************************************************************************** |
| 3 |
* |
| 4 |
* Copyright(c) 2008 - 2014 Intel Corporation. All rights reserved. |
| 5 |
* Copyright(c) 2018 Intel Corporation |
| 6 |
*****************************************************************************/ |
| 7 |
#include <linux/slab.h> |
| 8 |
#include <linux/types.h> |
| 9 |
#include <linux/etherdevice.h> |
| 10 |
#include <net/mac80211.h> |
| 11 |
|
| 12 |
#include "dev.h" |
| 13 |
#include "agn.h" |
| 14 |
|
| 15 |
/* For active scan, listen ACTIVE_DWELL_TIME (msec) on each channel after |
| 16 |
* sending probe req. This should be set long enough to hear probe responses |
| 17 |
* from more than one AP. */ |
| 18 |
#define IWL_ACTIVE_DWELL_TIME_24 (30) /* all times in msec */ |
| 19 |
#define IWL_ACTIVE_DWELL_TIME_52 (20) |
| 20 |
|
| 21 |
#define IWL_ACTIVE_DWELL_FACTOR_24GHZ (3) |
| 22 |
#define IWL_ACTIVE_DWELL_FACTOR_52GHZ (2) |
| 23 |
|
| 24 |
/* For passive scan, listen PASSIVE_DWELL_TIME (msec) on each channel. |
| 25 |
* Must be set longer than active dwell time. |
| 26 |
* For the most reliable scan, set > AP beacon interval (typically 100msec). */ |
| 27 |
#define IWL_PASSIVE_DWELL_TIME_24 (20) /* all times in msec */ |
| 28 |
#define IWL_PASSIVE_DWELL_TIME_52 (10) |
| 29 |
#define IWL_PASSIVE_DWELL_BASE (100) |
| 30 |
#define IWL_CHANNEL_TUNE_TIME 5 |
| 31 |
#define MAX_SCAN_CHANNEL 50 |
| 32 |
|
| 33 |
/* For reset radio, need minimal dwell time only */ |
| 34 |
#define IWL_RADIO_RESET_DWELL_TIME 5 |
| 35 |
|
| 36 |
static int iwl_send_scan_abort(struct iwl_priv *priv) |
| 37 |
{ |
| 38 |
int ret; |
| 39 |
struct iwl_host_cmd cmd = { |
| 40 |
.id = REPLY_SCAN_ABORT_CMD, |
| 41 |
.flags = CMD_WANT_SKB, |
| 42 |
}; |
| 43 |
__le32 *status; |
| 44 |
|
| 45 |
/* Exit instantly with error when device is not ready |
| 46 |
* to receive scan abort command or it does not perform |
| 47 |
* hardware scan currently */ |
| 48 |
if (!test_bit(STATUS_READY, &priv->status) || |
| 49 |
!test_bit(STATUS_SCAN_HW, &priv->status) || |
| 50 |
test_bit(STATUS_FW_ERROR, &priv->status)) |
| 51 |
return -EIO; |
| 52 |
|
| 53 |
ret = iwl_dvm_send_cmd(priv, &cmd); |
| 54 |
if (ret) |
| 55 |
return ret; |
| 56 |
|
| 57 |
status = (void *)cmd.resp_pkt->data; |
| 58 |
if (*status != CAN_ABORT_STATUS) { |
| 59 |
/* The scan abort will return 1 for success or |
| 60 |
* 2 for "failure". A failure condition can be |
| 61 |
* due to simply not being in an active scan which |
| 62 |
* can occur if we send the scan abort before we |
| 63 |
* the microcode has notified us that a scan is |
| 64 |
* completed. */ |
| 65 |
IWL_DEBUG_SCAN(priv, "SCAN_ABORT ret %d.\n", |
| 66 |
le32_to_cpu(*status)); |
| 67 |
ret = -EIO; |
| 68 |
} |
| 69 |
|
| 70 |
iwl_free_resp(&cmd); |
| 71 |
return ret; |
| 72 |
} |
| 73 |
|
| 74 |
static void iwl_complete_scan(struct iwl_priv *priv, bool aborted) |
| 75 |
{ |
| 76 |
struct cfg80211_scan_info info = { |
| 77 |
.aborted = aborted, |
| 78 |
}; |
| 79 |
|
| 80 |
/* check if scan was requested from mac80211 */ |
| 81 |
if (priv->scan_request) { |
| 82 |
IWL_DEBUG_SCAN(priv, "Complete scan in mac80211\n"); |
| 83 |
ieee80211_scan_completed(priv->hw, &info); |
| 84 |
} |
| 85 |
|
| 86 |
priv->scan_type = IWL_SCAN_NORMAL; |
| 87 |
priv->scan_vif = NULL; |
| 88 |
priv->scan_request = NULL; |
| 89 |
} |
| 90 |
|
| 91 |
static void iwl_process_scan_complete(struct iwl_priv *priv) |
| 92 |
{ |
| 93 |
bool aborted; |
| 94 |
|
| 95 |
lockdep_assert_held(&priv->mutex); |
| 96 |
|
| 97 |
if (!test_and_clear_bit(STATUS_SCAN_COMPLETE, &priv->status)) |
| 98 |
return; |
| 99 |
|
| 100 |
IWL_DEBUG_SCAN(priv, "Completed scan.\n"); |
| 101 |
|
| 102 |
cancel_delayed_work(&priv->scan_check); |
| 103 |
|
| 104 |
aborted = test_and_clear_bit(STATUS_SCAN_ABORTING, &priv->status); |
| 105 |
if (aborted) |
| 106 |
IWL_DEBUG_SCAN(priv, "Aborted scan completed.\n"); |
| 107 |
|
| 108 |
if (!test_and_clear_bit(STATUS_SCANNING, &priv->status)) { |
| 109 |
IWL_DEBUG_SCAN(priv, "Scan already completed.\n"); |
| 110 |
goto out_settings; |
| 111 |
} |
| 112 |
|
| 113 |
if (priv->scan_type != IWL_SCAN_NORMAL && !aborted) { |
| 114 |
int err; |
| 115 |
|
| 116 |
/* Check if mac80211 requested scan during our internal scan */ |
| 117 |
if (priv->scan_request == NULL) |
| 118 |
goto out_complete; |
| 119 |
|
| 120 |
/* If so request a new scan */ |
| 121 |
err = iwl_scan_initiate(priv, priv->scan_vif, IWL_SCAN_NORMAL, |
| 122 |
priv->scan_request->channels[0]->band); |
| 123 |
if (err) { |
| 124 |
IWL_DEBUG_SCAN(priv, |
| 125 |
"failed to initiate pending scan: %d\n", err); |
| 126 |
aborted = true; |
| 127 |
goto out_complete; |
| 128 |
} |
| 129 |
|
| 130 |
return; |
| 131 |
} |
| 132 |
|
| 133 |
out_complete: |
| 134 |
iwl_complete_scan(priv, aborted); |
| 135 |
|
| 136 |
out_settings: |
| 137 |
/* Can we still talk to firmware ? */ |
| 138 |
if (!iwl_is_ready_rf(priv)) |
| 139 |
return; |
| 140 |
|
| 141 |
iwlagn_post_scan(priv); |
| 142 |
} |
| 143 |
|
| 144 |
void iwl_force_scan_end(struct iwl_priv *priv) |
| 145 |
{ |
| 146 |
lockdep_assert_held(&priv->mutex); |
| 147 |
|
| 148 |
if (!test_bit(STATUS_SCANNING, &priv->status)) { |
| 149 |
IWL_DEBUG_SCAN(priv, "Forcing scan end while not scanning\n"); |
| 150 |
return; |
| 151 |
} |
| 152 |
|
| 153 |
IWL_DEBUG_SCAN(priv, "Forcing scan end\n"); |
| 154 |
clear_bit(STATUS_SCANNING, &priv->status); |
| 155 |
clear_bit(STATUS_SCAN_HW, &priv->status); |
| 156 |
clear_bit(STATUS_SCAN_ABORTING, &priv->status); |
| 157 |
clear_bit(STATUS_SCAN_COMPLETE, &priv->status); |
| 158 |
iwl_complete_scan(priv, true); |
| 159 |
} |
| 160 |
|
| 161 |
static void iwl_do_scan_abort(struct iwl_priv *priv) |
| 162 |
{ |
| 163 |
int ret; |
| 164 |
|
| 165 |
lockdep_assert_held(&priv->mutex); |
| 166 |
|
| 167 |
if (!test_bit(STATUS_SCANNING, &priv->status)) { |
| 168 |
IWL_DEBUG_SCAN(priv, "Not performing scan to abort\n"); |
| 169 |
return; |
| 170 |
} |
| 171 |
|
| 172 |
if (test_and_set_bit(STATUS_SCAN_ABORTING, &priv->status)) { |
| 173 |
IWL_DEBUG_SCAN(priv, "Scan abort in progress\n"); |
| 174 |
return; |
| 175 |
} |
| 176 |
|
| 177 |
ret = iwl_send_scan_abort(priv); |
| 178 |
if (ret) { |
| 179 |
IWL_DEBUG_SCAN(priv, "Send scan abort failed %d\n", ret); |
| 180 |
iwl_force_scan_end(priv); |
| 181 |
} else |
| 182 |
IWL_DEBUG_SCAN(priv, "Successfully send scan abort\n"); |
| 183 |
} |
| 184 |
|
| 185 |
/* |
| 186 |
* iwl_scan_cancel - Cancel any currently executing HW scan |
| 187 |
*/ |
| 188 |
int iwl_scan_cancel(struct iwl_priv *priv) |
| 189 |
{ |
| 190 |
IWL_DEBUG_SCAN(priv, "Queuing abort scan\n"); |
| 191 |
queue_work(priv->workqueue, &priv->abort_scan); |
| 192 |
return 0; |
| 193 |
} |
| 194 |
|
| 195 |
/* |
| 196 |
* iwl_scan_cancel_timeout - Cancel any currently executing HW scan |
| 197 |
* @ms: amount of time to wait (in milliseconds) for scan to abort |
| 198 |
*/ |
| 199 |
void iwl_scan_cancel_timeout(struct iwl_priv *priv, unsigned long ms) |
| 200 |
{ |
| 201 |
unsigned long timeout = jiffies + msecs_to_jiffies(ms); |
| 202 |
|
| 203 |
lockdep_assert_held(&priv->mutex); |
| 204 |
|
| 205 |
IWL_DEBUG_SCAN(priv, "Scan cancel timeout\n"); |
| 206 |
|
| 207 |
iwl_do_scan_abort(priv); |
| 208 |
|
| 209 |
while (time_before_eq(jiffies, timeout)) { |
| 210 |
if (!test_bit(STATUS_SCAN_HW, &priv->status)) |
| 211 |
goto finished; |
| 212 |
msleep(20); |
| 213 |
} |
| 214 |
|
| 215 |
return; |
| 216 |
|
| 217 |
finished: |
| 218 |
/* |
| 219 |
* Now STATUS_SCAN_HW is clear. This means that the |
| 220 |
* device finished, but the background work is going |
| 221 |
* to execute at best as soon as we release the mutex. |
| 222 |
* Since we need to be able to issue a new scan right |
| 223 |
* after this function returns, run the complete here. |
| 224 |
* The STATUS_SCAN_COMPLETE bit will then be cleared |
| 225 |
* and prevent the background work from "completing" |
| 226 |
* a possible new scan. |
| 227 |
*/ |
| 228 |
iwl_process_scan_complete(priv); |
| 229 |
} |
| 230 |
|
| 231 |
/* Service response to REPLY_SCAN_CMD (0x80) */ |
| 232 |
static void iwl_rx_reply_scan(struct iwl_priv *priv, |
| 233 |
struct iwl_rx_cmd_buffer *rxb) |
| 234 |
{ |
| 235 |
#ifdef CONFIG_IWLWIFI_DEBUG |
| 236 |
struct iwl_rx_packet *pkt = rxb_addr(rxb); |
| 237 |
struct iwl_scanreq_notification *notif = (void *)pkt->data; |
| 238 |
|
| 239 |
IWL_DEBUG_SCAN(priv, "Scan request status = 0x%x\n", notif->status); |
| 240 |
#endif |
| 241 |
} |
| 242 |
|
| 243 |
/* Service SCAN_START_NOTIFICATION (0x82) */ |
| 244 |
static void iwl_rx_scan_start_notif(struct iwl_priv *priv, |
| 245 |
struct iwl_rx_cmd_buffer *rxb) |
| 246 |
{ |
| 247 |
struct iwl_rx_packet *pkt = rxb_addr(rxb); |
| 248 |
struct iwl_scanstart_notification *notif = (void *)pkt->data; |
| 249 |
|
| 250 |
priv->scan_start_tsf = le32_to_cpu(notif->tsf_low); |
| 251 |
IWL_DEBUG_SCAN(priv, "Scan start: " |
| 252 |
"%d [802.11%s] " |
| 253 |
"(TSF: 0x%08X:%08X) - %d (beacon timer %u)\n", |
| 254 |
notif->channel, |
| 255 |
notif->band ? "bg" : "a", |
| 256 |
le32_to_cpu(notif->tsf_high), |
| 257 |
le32_to_cpu(notif->tsf_low), |
| 258 |
notif->status, notif->beacon_timer); |
| 259 |
} |
| 260 |
|
| 261 |
/* Service SCAN_RESULTS_NOTIFICATION (0x83) */ |
| 262 |
static void iwl_rx_scan_results_notif(struct iwl_priv *priv, |
| 263 |
struct iwl_rx_cmd_buffer *rxb) |
| 264 |
{ |
| 265 |
#ifdef CONFIG_IWLWIFI_DEBUG |
| 266 |
struct iwl_rx_packet *pkt = rxb_addr(rxb); |
| 267 |
struct iwl_scanresults_notification *notif = (void *)pkt->data; |
| 268 |
|
| 269 |
IWL_DEBUG_SCAN(priv, "Scan ch.res: " |
| 270 |
"%d [802.11%s] " |
| 271 |
"probe status: %u:%u " |
| 272 |
"(TSF: 0x%08X:%08X) - %d " |
| 273 |
"elapsed=%lu usec\n", |
| 274 |
notif->channel, |
| 275 |
notif->band ? "bg" : "a", |
| 276 |
notif->probe_status, notif->num_probe_not_sent, |
| 277 |
le32_to_cpu(notif->tsf_high), |
| 278 |
le32_to_cpu(notif->tsf_low), |
| 279 |
le32_to_cpu(notif->statistics[0]), |
| 280 |
le32_to_cpu(notif->tsf_low) - priv->scan_start_tsf); |
| 281 |
#endif |
| 282 |
} |
| 283 |
|
| 284 |
/* Service SCAN_COMPLETE_NOTIFICATION (0x84) */ |
| 285 |
static void iwl_rx_scan_complete_notif(struct iwl_priv *priv, |
| 286 |
struct iwl_rx_cmd_buffer *rxb) |
| 287 |
{ |
| 288 |
struct iwl_rx_packet *pkt = rxb_addr(rxb); |
| 289 |
struct iwl_scancomplete_notification *scan_notif = (void *)pkt->data; |
| 290 |
|
| 291 |
IWL_DEBUG_SCAN(priv, "Scan complete: %d channels (TSF 0x%08X:%08X) - %d\n", |
| 292 |
scan_notif->scanned_channels, |
| 293 |
scan_notif->tsf_low, |
| 294 |
scan_notif->tsf_high, scan_notif->status); |
| 295 |
|
| 296 |
IWL_DEBUG_SCAN(priv, "Scan on %sGHz took %dms\n", |
| 297 |
(priv->scan_band == NL80211_BAND_2GHZ) ? "2.4" : "5.2", |
| 298 |
jiffies_to_msecs(jiffies - priv->scan_start)); |
| 299 |
|
| 300 |
/* |
| 301 |
* When aborting, we run the scan completed background work inline |
| 302 |
* and the background work must then do nothing. The SCAN_COMPLETE |
| 303 |
* bit helps implement that logic and thus needs to be set before |
| 304 |
* queueing the work. Also, since the scan abort waits for SCAN_HW |
| 305 |
* to clear, we need to set SCAN_COMPLETE before clearing SCAN_HW |
| 306 |
* to avoid a race there. |
| 307 |
*/ |
| 308 |
set_bit(STATUS_SCAN_COMPLETE, &priv->status); |
| 309 |
clear_bit(STATUS_SCAN_HW, &priv->status); |
| 310 |
queue_work(priv->workqueue, &priv->scan_completed); |
| 311 |
|
| 312 |
if (priv->iw_mode != NL80211_IFTYPE_ADHOC && |
| 313 |
iwl_advanced_bt_coexist(priv) && |
| 314 |
priv->bt_status != scan_notif->bt_status) { |
| 315 |
if (scan_notif->bt_status) { |
| 316 |
/* BT on */ |
| 317 |
if (!priv->bt_ch_announce) |
| 318 |
priv->bt_traffic_load = |
| 319 |
IWL_BT_COEX_TRAFFIC_LOAD_HIGH; |
| 320 |
/* |
| 321 |
* otherwise, no traffic load information provided |
| 322 |
* no changes made |
| 323 |
*/ |
| 324 |
} else { |
| 325 |
/* BT off */ |
| 326 |
priv->bt_traffic_load = |
| 327 |
IWL_BT_COEX_TRAFFIC_LOAD_NONE; |
| 328 |
} |
| 329 |
priv->bt_status = scan_notif->bt_status; |
| 330 |
queue_work(priv->workqueue, |
| 331 |
&priv->bt_traffic_change_work); |
| 332 |
} |
| 333 |
} |
| 334 |
|
| 335 |
void iwl_setup_rx_scan_handlers(struct iwl_priv *priv) |
| 336 |
{ |
| 337 |
/* scan handlers */ |
| 338 |
priv->rx_handlers[REPLY_SCAN_CMD] = iwl_rx_reply_scan; |
| 339 |
priv->rx_handlers[SCAN_START_NOTIFICATION] = iwl_rx_scan_start_notif; |
| 340 |
priv->rx_handlers[SCAN_RESULTS_NOTIFICATION] = |
| 341 |
iwl_rx_scan_results_notif; |
| 342 |
priv->rx_handlers[SCAN_COMPLETE_NOTIFICATION] = |
| 343 |
iwl_rx_scan_complete_notif; |
| 344 |
} |
| 345 |
|
| 346 |
static u16 iwl_get_active_dwell_time(struct iwl_priv *priv, |
| 347 |
enum nl80211_band band, u8 n_probes) |
| 348 |
{ |
| 349 |
if (band == NL80211_BAND_5GHZ) |
| 350 |
return IWL_ACTIVE_DWELL_TIME_52 + |
| 351 |
IWL_ACTIVE_DWELL_FACTOR_52GHZ * (n_probes + 1); |
| 352 |
else |
| 353 |
return IWL_ACTIVE_DWELL_TIME_24 + |
| 354 |
IWL_ACTIVE_DWELL_FACTOR_24GHZ * (n_probes + 1); |
| 355 |
} |
| 356 |
|
| 357 |
static u16 iwl_limit_dwell(struct iwl_priv *priv, u16 dwell_time) |
| 358 |
{ |
| 359 |
struct iwl_rxon_context *ctx; |
| 360 |
int limits[NUM_IWL_RXON_CTX] = {}; |
| 361 |
int n_active = 0; |
| 362 |
u16 limit; |
| 363 |
|
| 364 |
BUILD_BUG_ON(NUM_IWL_RXON_CTX != 2); |
| 365 |
|
| 366 |
/* |
| 367 |
* If we're associated, we clamp the dwell time 98% |
| 368 |
* of the beacon interval (minus 2 * channel tune time) |
| 369 |
* If both contexts are active, we have to restrict to |
| 370 |
* 1/2 of the minimum of them, because they might be in |
| 371 |
* lock-step with the time inbetween only half of what |
| 372 |
* time we'd have in each of them. |
| 373 |
*/ |
| 374 |
for_each_context(priv, ctx) { |
| 375 |
switch (ctx->staging.dev_type) { |
| 376 |
case RXON_DEV_TYPE_P2P: |
| 377 |
/* no timing constraints */ |
| 378 |
continue; |
| 379 |
case RXON_DEV_TYPE_ESS: |
| 380 |
default: |
| 381 |
/* timing constraints if associated */ |
| 382 |
if (!iwl_is_associated_ctx(ctx)) |
| 383 |
continue; |
| 384 |
break; |
| 385 |
case RXON_DEV_TYPE_CP: |
| 386 |
case RXON_DEV_TYPE_2STA: |
| 387 |
/* |
| 388 |
* These seem to always have timers for TBTT |
| 389 |
* active in uCode even when not associated yet. |
| 390 |
*/ |
| 391 |
break; |
| 392 |
} |
| 393 |
|
| 394 |
limits[n_active++] = ctx->beacon_int ?: IWL_PASSIVE_DWELL_BASE; |
| 395 |
} |
| 396 |
|
| 397 |
switch (n_active) { |
| 398 |
case 0: |
| 399 |
return dwell_time; |
| 400 |
case 2: |
| 401 |
limit = (limits[1] * 98) / 100 - IWL_CHANNEL_TUNE_TIME * 2; |
| 402 |
limit /= 2; |
| 403 |
dwell_time = min(limit, dwell_time); |
| 404 |
fallthrough; |
| 405 |
case 1: |
| 406 |
limit = (limits[0] * 98) / 100 - IWL_CHANNEL_TUNE_TIME * 2; |
| 407 |
limit /= n_active; |
| 408 |
return min(limit, dwell_time); |
| 409 |
default: |
| 410 |
WARN_ON_ONCE(1); |
| 411 |
return dwell_time; |
| 412 |
} |
| 413 |
} |
| 414 |
|
| 415 |
static u16 iwl_get_passive_dwell_time(struct iwl_priv *priv, |
| 416 |
enum nl80211_band band) |
| 417 |
{ |
| 418 |
u16 passive = (band == NL80211_BAND_2GHZ) ? |
| 419 |
IWL_PASSIVE_DWELL_BASE + IWL_PASSIVE_DWELL_TIME_24 : |
| 420 |
IWL_PASSIVE_DWELL_BASE + IWL_PASSIVE_DWELL_TIME_52; |
| 421 |
|
| 422 |
return iwl_limit_dwell(priv, passive); |
| 423 |
} |
| 424 |
|
| 425 |
/* Return valid, unused, channel for a passive scan to reset the RF */ |
| 426 |
static u8 iwl_get_single_channel_number(struct iwl_priv *priv, |
| 427 |
enum nl80211_band band) |
| 428 |
{ |
| 429 |
struct ieee80211_supported_band *sband = priv->hw->wiphy->bands[band]; |
| 430 |
struct iwl_rxon_context *ctx; |
| 431 |
int i; |
| 432 |
|
| 433 |
for (i = 0; i < sband->n_channels; i++) { |
| 434 |
bool busy = false; |
| 435 |
|
| 436 |
for_each_context(priv, ctx) { |
| 437 |
busy = sband->channels[i].hw_value == |
| 438 |
le16_to_cpu(ctx->staging.channel); |
| 439 |
if (busy) |
| 440 |
break; |
| 441 |
} |
| 442 |
|
| 443 |
if (busy) |
| 444 |
continue; |
| 445 |
|
| 446 |
if (!(sband->channels[i].flags & IEEE80211_CHAN_DISABLED)) |
| 447 |
return sband->channels[i].hw_value; |
| 448 |
} |
| 449 |
|
| 450 |
return 0; |
| 451 |
} |
| 452 |
|
| 453 |
static int iwl_get_channel_for_reset_scan(struct iwl_priv *priv, |
| 454 |
struct ieee80211_vif *vif, |
| 455 |
enum nl80211_band band, |
| 456 |
struct iwl_scan_channel *scan_ch) |
| 457 |
{ |
| 458 |
const struct ieee80211_supported_band *sband; |
| 459 |
u16 channel; |
| 460 |
|
| 461 |
sband = iwl_get_hw_mode(priv, band); |
| 462 |
if (!sband) { |
| 463 |
IWL_ERR(priv, "invalid band\n"); |
| 464 |
return 0; |
| 465 |
} |
| 466 |
|
| 467 |
channel = iwl_get_single_channel_number(priv, band); |
| 468 |
if (channel) { |
| 469 |
scan_ch->channel = cpu_to_le16(channel); |
| 470 |
scan_ch->type = SCAN_CHANNEL_TYPE_PASSIVE; |
| 471 |
scan_ch->active_dwell = |
| 472 |
cpu_to_le16(IWL_RADIO_RESET_DWELL_TIME); |
| 473 |
scan_ch->passive_dwell = |
| 474 |
cpu_to_le16(IWL_RADIO_RESET_DWELL_TIME); |
| 475 |
/* Set txpower levels to defaults */ |
| 476 |
scan_ch->dsp_atten = 110; |
| 477 |
if (band == NL80211_BAND_5GHZ) |
| 478 |
scan_ch->tx_gain = ((1 << 5) | (3 << 3)) | 3; |
| 479 |
else |
| 480 |
scan_ch->tx_gain = ((1 << 5) | (5 << 3)); |
| 481 |
return 1; |
| 482 |
} |
| 483 |
|
| 484 |
IWL_ERR(priv, "no valid channel found\n"); |
| 485 |
return 0; |
| 486 |
} |
| 487 |
|
| 488 |
static int iwl_get_channels_for_scan(struct iwl_priv *priv, |
| 489 |
struct ieee80211_vif *vif, |
| 490 |
enum nl80211_band band, |
| 491 |
u8 is_active, u8 n_probes, |
| 492 |
struct iwl_scan_channel *scan_ch) |
| 493 |
{ |
| 494 |
struct ieee80211_channel *chan; |
| 495 |
const struct ieee80211_supported_band *sband; |
| 496 |
u16 passive_dwell = 0; |
| 497 |
u16 active_dwell = 0; |
| 498 |
int added, i; |
| 499 |
u16 channel; |
| 500 |
|
| 501 |
sband = iwl_get_hw_mode(priv, band); |
| 502 |
if (!sband) |
| 503 |
return 0; |
| 504 |
|
| 505 |
active_dwell = iwl_get_active_dwell_time(priv, band, n_probes); |
| 506 |
passive_dwell = iwl_get_passive_dwell_time(priv, band); |
| 507 |
|
| 508 |
if (passive_dwell <= active_dwell) |
| 509 |
passive_dwell = active_dwell + 1; |
| 510 |
|
| 511 |
for (i = 0, added = 0; i < priv->scan_request->n_channels; i++) { |
| 512 |
chan = priv->scan_request->channels[i]; |
| 513 |
|
| 514 |
if (chan->band != band) |
| 515 |
continue; |
| 516 |
|
| 517 |
channel = chan->hw_value; |
| 518 |
scan_ch->channel = cpu_to_le16(channel); |
| 519 |
|
| 520 |
if (!is_active || (chan->flags & IEEE80211_CHAN_NO_IR)) |
| 521 |
scan_ch->type = SCAN_CHANNEL_TYPE_PASSIVE; |
| 522 |
else |
| 523 |
scan_ch->type = SCAN_CHANNEL_TYPE_ACTIVE; |
| 524 |
|
| 525 |
if (n_probes) |
| 526 |
scan_ch->type |= IWL_SCAN_PROBE_MASK(n_probes); |
| 527 |
|
| 528 |
scan_ch->active_dwell = cpu_to_le16(active_dwell); |
| 529 |
scan_ch->passive_dwell = cpu_to_le16(passive_dwell); |
| 530 |
|
| 531 |
/* Set txpower levels to defaults */ |
| 532 |
scan_ch->dsp_atten = 110; |
| 533 |
|
| 534 |
/* NOTE: if we were doing 6Mb OFDM for scans we'd use |
| 535 |
* power level: |
| 536 |
* scan_ch->tx_gain = ((1 << 5) | (2 << 3)) | 3; |
| 537 |
*/ |
| 538 |
if (band == NL80211_BAND_5GHZ) |
| 539 |
scan_ch->tx_gain = ((1 << 5) | (3 << 3)) | 3; |
| 540 |
else |
| 541 |
scan_ch->tx_gain = ((1 << 5) | (5 << 3)); |
| 542 |
|
| 543 |
IWL_DEBUG_SCAN(priv, "Scanning ch=%d prob=0x%X [%s %d]\n", |
| 544 |
channel, le32_to_cpu(scan_ch->type), |
| 545 |
(scan_ch->type & SCAN_CHANNEL_TYPE_ACTIVE) ? |
| 546 |
"ACTIVE" : "PASSIVE", |
| 547 |
(scan_ch->type & SCAN_CHANNEL_TYPE_ACTIVE) ? |
| 548 |
active_dwell : passive_dwell); |
| 549 |
|
| 550 |
scan_ch++; |
| 551 |
added++; |
| 552 |
} |
| 553 |
|
| 554 |
IWL_DEBUG_SCAN(priv, "total channels to scan %d\n", added); |
| 555 |
return added; |
| 556 |
} |
| 557 |
|
| 558 |
/* |
| 559 |
* iwl_fill_probe_req - fill in all required fields and IE for probe request |
| 560 |
*/ |
| 561 |
static u16 iwl_fill_probe_req(struct ieee80211_mgmt *frame, const u8 *ta, |
| 562 |
const u8 *ies, int ie_len, const u8 *ssid, |
| 563 |
u8 ssid_len, int left) |
| 564 |
{ |
| 565 |
int len = 0; |
| 566 |
u8 *pos = NULL; |
| 567 |
|
| 568 |
/* Make sure there is enough space for the probe request, |
| 569 |
* two mandatory IEs and the data */ |
| 570 |
left -= 24; |
| 571 |
if (left < 0) |
| 572 |
return 0; |
| 573 |
|
| 574 |
frame->frame_control = cpu_to_le16(IEEE80211_STYPE_PROBE_REQ); |
| 575 |
eth_broadcast_addr(frame->da); |
| 576 |
memcpy(frame->sa, ta, ETH_ALEN); |
| 577 |
eth_broadcast_addr(frame->bssid); |
| 578 |
frame->seq_ctrl = 0; |
| 579 |
|
| 580 |
len += 24; |
| 581 |
|
| 582 |
/* ...next IE... */ |
| 583 |
pos = &frame->u.probe_req.variable[0]; |
| 584 |
|
| 585 |
/* fill in our SSID IE */ |
| 586 |
left -= ssid_len + 2; |
| 587 |
if (left < 0) |
| 588 |
return 0; |
| 589 |
*pos++ = WLAN_EID_SSID; |
| 590 |
*pos++ = ssid_len; |
| 591 |
if (ssid && ssid_len) { |
| 592 |
memcpy(pos, ssid, ssid_len); |
| 593 |
pos += ssid_len; |
| 594 |
} |
| 595 |
|
| 596 |
len += ssid_len + 2; |
| 597 |
|
| 598 |
if (WARN_ON(left < ie_len)) |
| 599 |
return len; |
| 600 |
|
| 601 |
if (ies && ie_len) { |
| 602 |
memcpy(pos, ies, ie_len); |
| 603 |
len += ie_len; |
| 604 |
} |
| 605 |
|
| 606 |
return (u16)len; |
| 607 |
} |
| 608 |
|
| 609 |
static int iwlagn_request_scan(struct iwl_priv *priv, struct ieee80211_vif *vif) |
| 610 |
{ |
| 611 |
struct iwl_host_cmd cmd = { |
| 612 |
.id = REPLY_SCAN_CMD, |
| 613 |
.len = { sizeof(struct iwl_scan_cmd), }, |
| 614 |
}; |
| 615 |
struct iwl_scan_cmd *scan; |
| 616 |
struct iwl_rxon_context *ctx = &priv->contexts[IWL_RXON_CTX_BSS]; |
| 617 |
u32 rate_flags = 0; |
| 618 |
u16 cmd_len = 0; |
| 619 |
u16 rx_chain = 0; |
| 620 |
enum nl80211_band band; |
| 621 |
u8 n_probes = 0; |
| 622 |
u8 rx_ant = priv->nvm_data->valid_rx_ant; |
| 623 |
u8 rate; |
| 624 |
bool is_active = false; |
| 625 |
int chan_mod; |
| 626 |
u8 active_chains; |
| 627 |
u8 scan_tx_antennas = priv->nvm_data->valid_tx_ant; |
| 628 |
int ret; |
| 629 |
size_t scan_cmd_size = sizeof(struct iwl_scan_cmd) + |
| 630 |
MAX_SCAN_CHANNEL * sizeof(struct iwl_scan_channel) + |
| 631 |
priv->fw->ucode_capa.max_probe_length; |
| 632 |
const u8 *ssid = NULL; |
| 633 |
u8 ssid_len = 0; |
| 634 |
|
| 635 |
if (WARN_ON(priv->scan_type == IWL_SCAN_NORMAL && |
| 636 |
(!priv->scan_request || |
| 637 |
priv->scan_request->n_channels > MAX_SCAN_CHANNEL))) |
| 638 |
return -EINVAL; |
| 639 |
|
| 640 |
lockdep_assert_held(&priv->mutex); |
| 641 |
|
| 642 |
if (vif) |
| 643 |
ctx = iwl_rxon_ctx_from_vif(vif); |
| 644 |
|
| 645 |
if (!priv->scan_cmd) { |
| 646 |
priv->scan_cmd = kmalloc(scan_cmd_size, GFP_KERNEL); |
| 647 |
if (!priv->scan_cmd) { |
| 648 |
IWL_DEBUG_SCAN(priv, |
| 649 |
"fail to allocate memory for scan\n"); |
| 650 |
return -ENOMEM; |
| 651 |
} |
| 652 |
priv->scan_cmd_size = scan_cmd_size; |
| 653 |
} |
| 654 |
if (priv->scan_cmd_size < scan_cmd_size) { |
| 655 |
IWL_DEBUG_SCAN(priv, |
| 656 |
"memory needed for scan grew unexpectedly\n"); |
| 657 |
return -ENOMEM; |
| 658 |
} |
| 659 |
scan = priv->scan_cmd; |
| 660 |
memset(scan, 0, priv->scan_cmd_size); |
| 661 |
|
| 662 |
scan->quiet_plcp_th = IWL_PLCP_QUIET_THRESH; |
| 663 |
scan->quiet_time = IWL_ACTIVE_QUIET_TIME; |
| 664 |
|
| 665 |
if (iwl_is_any_associated(priv)) { |
| 666 |
u16 interval = 0; |
| 667 |
u32 extra; |
| 668 |
u32 suspend_time = 100; |
| 669 |
u32 scan_suspend_time = 100; |
| 670 |
|
| 671 |
IWL_DEBUG_INFO(priv, "Scanning while associated...\n"); |
| 672 |
switch (priv->scan_type) { |
| 673 |
case IWL_SCAN_RADIO_RESET: |
| 674 |
interval = 0; |
| 675 |
break; |
| 676 |
case IWL_SCAN_NORMAL: |
| 677 |
interval = vif->bss_conf.beacon_int; |
| 678 |
break; |
| 679 |
} |
| 680 |
|
| 681 |
scan->suspend_time = 0; |
| 682 |
scan->max_out_time = cpu_to_le32(200 * 1024); |
| 683 |
if (!interval) |
| 684 |
interval = suspend_time; |
| 685 |
|
| 686 |
extra = (suspend_time / interval) << 22; |
| 687 |
scan_suspend_time = (extra | |
| 688 |
((suspend_time % interval) * 1024)); |
| 689 |
scan->suspend_time = cpu_to_le32(scan_suspend_time); |
| 690 |
IWL_DEBUG_SCAN(priv, "suspend_time 0x%X beacon interval %d\n", |
| 691 |
scan_suspend_time, interval); |
| 692 |
} |
| 693 |
|
| 694 |
switch (priv->scan_type) { |
| 695 |
case IWL_SCAN_RADIO_RESET: |
| 696 |
IWL_DEBUG_SCAN(priv, "Start internal passive scan.\n"); |
| 697 |
/* |
| 698 |
* Override quiet time as firmware checks that active |
| 699 |
* dwell is >= quiet; since we use passive scan it'll |
| 700 |
* not actually be used. |
| 701 |
*/ |
| 702 |
scan->quiet_time = cpu_to_le16(IWL_RADIO_RESET_DWELL_TIME); |
| 703 |
break; |
| 704 |
case IWL_SCAN_NORMAL: |
| 705 |
if (priv->scan_request->n_ssids) { |
| 706 |
int i, p = 0; |
| 707 |
IWL_DEBUG_SCAN(priv, "Kicking off active scan\n"); |
| 708 |
/* |
| 709 |
* The highest priority SSID is inserted to the |
| 710 |
* probe request template. |
| 711 |
*/ |
| 712 |
ssid_len = priv->scan_request->ssids[0].ssid_len; |
| 713 |
ssid = priv->scan_request->ssids[0].ssid; |
| 714 |
|
| 715 |
/* |
| 716 |
* Invert the order of ssids, the firmware will invert |
| 717 |
* it back. |
| 718 |
*/ |
| 719 |
for (i = priv->scan_request->n_ssids - 1; i >= 1; i--) { |
| 720 |
scan->direct_scan[p].id = WLAN_EID_SSID; |
| 721 |
scan->direct_scan[p].len = |
| 722 |
priv->scan_request->ssids[i].ssid_len; |
| 723 |
memcpy(scan->direct_scan[p].ssid, |
| 724 |
priv->scan_request->ssids[i].ssid, |
| 725 |
priv->scan_request->ssids[i].ssid_len); |
| 726 |
n_probes++; |
| 727 |
p++; |
| 728 |
} |
| 729 |
is_active = true; |
| 730 |
} else |
| 731 |
IWL_DEBUG_SCAN(priv, "Start passive scan.\n"); |
| 732 |
break; |
| 733 |
} |
| 734 |
|
| 735 |
scan->tx_cmd.tx_flags = TX_CMD_FLG_SEQ_CTL_MSK; |
| 736 |
scan->tx_cmd.sta_id = ctx->bcast_sta_id; |
| 737 |
scan->tx_cmd.stop_time.life_time = TX_CMD_LIFE_TIME_INFINITE; |
| 738 |
|
| 739 |
switch (priv->scan_band) { |
| 740 |
case NL80211_BAND_2GHZ: |
| 741 |
scan->flags = RXON_FLG_BAND_24G_MSK | RXON_FLG_AUTO_DETECT_MSK; |
| 742 |
chan_mod = le32_to_cpu( |
| 743 |
priv->contexts[IWL_RXON_CTX_BSS].active.flags & |
| 744 |
RXON_FLG_CHANNEL_MODE_MSK) |
| 745 |
>> RXON_FLG_CHANNEL_MODE_POS; |
| 746 |
if ((priv->scan_request && priv->scan_request->no_cck) || |
| 747 |
chan_mod == CHANNEL_MODE_PURE_40) { |
| 748 |
rate = IWL_RATE_6M_PLCP; |
| 749 |
} else { |
| 750 |
rate = IWL_RATE_1M_PLCP; |
| 751 |
rate_flags = RATE_MCS_CCK_MSK; |
| 752 |
} |
| 753 |
/* |
| 754 |
* Internal scans are passive, so we can indiscriminately set |
| 755 |
* the BT ignore flag on 2.4 GHz since it applies to TX only. |
| 756 |
*/ |
| 757 |
if (priv->lib->bt_params && |
| 758 |
priv->lib->bt_params->advanced_bt_coexist) |
| 759 |
scan->tx_cmd.tx_flags |= TX_CMD_FLG_IGNORE_BT; |
| 760 |
break; |
| 761 |
case NL80211_BAND_5GHZ: |
| 762 |
rate = IWL_RATE_6M_PLCP; |
| 763 |
break; |
| 764 |
default: |
| 765 |
IWL_WARN(priv, "Invalid scan band\n"); |
| 766 |
return -EIO; |
| 767 |
} |
| 768 |
|
| 769 |
/* |
| 770 |
* If active scanning is requested but a certain channel is |
| 771 |
* marked passive, we can do active scanning if we detect |
| 772 |
* transmissions. |
| 773 |
* |
| 774 |
* There is an issue with some firmware versions that triggers |
| 775 |
* a sysassert on a "good CRC threshold" of zero (== disabled), |
| 776 |
* on a radar channel even though this means that we should NOT |
| 777 |
* send probes. |
| 778 |
* |
| 779 |
* The "good CRC threshold" is the number of frames that we |
| 780 |
* need to receive during our dwell time on a channel before |
| 781 |
* sending out probes -- setting this to a huge value will |
| 782 |
* mean we never reach it, but at the same time work around |
| 783 |
* the aforementioned issue. Thus use IWL_GOOD_CRC_TH_NEVER |
| 784 |
* here instead of IWL_GOOD_CRC_TH_DISABLED. |
| 785 |
* |
| 786 |
* This was fixed in later versions along with some other |
| 787 |
* scan changes, and the threshold behaves as a flag in those |
| 788 |
* versions. |
| 789 |
*/ |
| 790 |
if (priv->new_scan_threshold_behaviour) |
| 791 |
scan->good_CRC_th = is_active ? IWL_GOOD_CRC_TH_DEFAULT : |
| 792 |
IWL_GOOD_CRC_TH_DISABLED; |
| 793 |
else |
| 794 |
scan->good_CRC_th = is_active ? IWL_GOOD_CRC_TH_DEFAULT : |
| 795 |
IWL_GOOD_CRC_TH_NEVER; |
| 796 |
|
| 797 |
band = priv->scan_band; |
| 798 |
|
| 799 |
if (band == NL80211_BAND_2GHZ && |
| 800 |
priv->lib->bt_params && |
| 801 |
priv->lib->bt_params->advanced_bt_coexist) { |
| 802 |
/* transmit 2.4 GHz probes only on first antenna */ |
| 803 |
scan_tx_antennas = first_antenna(scan_tx_antennas); |
| 804 |
} |
| 805 |
|
| 806 |
priv->scan_tx_ant[band] = iwl_toggle_tx_ant(priv, |
| 807 |
priv->scan_tx_ant[band], |
| 808 |
scan_tx_antennas); |
| 809 |
rate_flags |= iwl_ant_idx_to_flags(priv->scan_tx_ant[band]); |
| 810 |
scan->tx_cmd.rate_n_flags = iwl_hw_set_rate_n_flags(rate, rate_flags); |
| 811 |
|
| 812 |
/* |
| 813 |
* In power save mode while associated use one chain, |
| 814 |
* otherwise use all chains |
| 815 |
*/ |
| 816 |
if (test_bit(STATUS_POWER_PMI, &priv->status) && |
| 817 |
!(priv->hw->conf.flags & IEEE80211_CONF_IDLE)) { |
| 818 |
/* rx_ant has been set to all valid chains previously */ |
| 819 |
active_chains = rx_ant & |
| 820 |
((u8)(priv->chain_noise_data.active_chains)); |
| 821 |
if (!active_chains) |
| 822 |
active_chains = rx_ant; |
| 823 |
|
| 824 |
IWL_DEBUG_SCAN(priv, "chain_noise_data.active_chains: %u\n", |
| 825 |
priv->chain_noise_data.active_chains); |
| 826 |
|
| 827 |
rx_ant = first_antenna(active_chains); |
| 828 |
} |
| 829 |
if (priv->lib->bt_params && |
| 830 |
priv->lib->bt_params->advanced_bt_coexist && |
| 831 |
priv->bt_full_concurrent) { |
| 832 |
/* operated as 1x1 in full concurrency mode */ |
| 833 |
rx_ant = first_antenna(rx_ant); |
| 834 |
} |
| 835 |
|
| 836 |
/* MIMO is not used here, but value is required */ |
| 837 |
rx_chain |= |
| 838 |
priv->nvm_data->valid_rx_ant << RXON_RX_CHAIN_VALID_POS; |
| 839 |
rx_chain |= rx_ant << RXON_RX_CHAIN_FORCE_MIMO_SEL_POS; |
| 840 |
rx_chain |= rx_ant << RXON_RX_CHAIN_FORCE_SEL_POS; |
| 841 |
rx_chain |= 0x1 << RXON_RX_CHAIN_DRIVER_FORCE_POS; |
| 842 |
scan->rx_chain = cpu_to_le16(rx_chain); |
| 843 |
switch (priv->scan_type) { |
| 844 |
case IWL_SCAN_NORMAL: |
| 845 |
cmd_len = iwl_fill_probe_req( |
| 846 |
(struct ieee80211_mgmt *)scan->data, |
| 847 |
vif->addr, |
| 848 |
priv->scan_request->ie, |
| 849 |
priv->scan_request->ie_len, |
| 850 |
ssid, ssid_len, |
| 851 |
scan_cmd_size - sizeof(*scan)); |
| 852 |
break; |
| 853 |
case IWL_SCAN_RADIO_RESET: |
| 854 |
/* use bcast addr, will not be transmitted but must be valid */ |
| 855 |
cmd_len = iwl_fill_probe_req( |
| 856 |
(struct ieee80211_mgmt *)scan->data, |
| 857 |
iwl_bcast_addr, NULL, 0, |
| 858 |
NULL, 0, |
| 859 |
scan_cmd_size - sizeof(*scan)); |
| 860 |
break; |
| 861 |
default: |
| 862 |
BUG(); |
| 863 |
} |
| 864 |
scan->tx_cmd.len = cpu_to_le16(cmd_len); |
| 865 |
|
| 866 |
scan->filter_flags |= (RXON_FILTER_ACCEPT_GRP_MSK | |
| 867 |
RXON_FILTER_BCON_AWARE_MSK); |
| 868 |
|
| 869 |
switch (priv->scan_type) { |
| 870 |
case IWL_SCAN_RADIO_RESET: |
| 871 |
scan->channel_count = |
| 872 |
iwl_get_channel_for_reset_scan(priv, vif, band, |
| 873 |
(void *)&scan->data[cmd_len]); |
| 874 |
break; |
| 875 |
case IWL_SCAN_NORMAL: |
| 876 |
scan->channel_count = |
| 877 |
iwl_get_channels_for_scan(priv, vif, band, |
| 878 |
is_active, n_probes, |
| 879 |
(void *)&scan->data[cmd_len]); |
| 880 |
break; |
| 881 |
} |
| 882 |
|
| 883 |
if (scan->channel_count == 0) { |
| 884 |
IWL_DEBUG_SCAN(priv, "channel count %d\n", scan->channel_count); |
| 885 |
return -EIO; |
| 886 |
} |
| 887 |
|
| 888 |
cmd.len[0] += le16_to_cpu(scan->tx_cmd.len) + |
| 889 |
scan->channel_count * sizeof(struct iwl_scan_channel); |
| 890 |
cmd.data[0] = scan; |
| 891 |
cmd.dataflags[0] = IWL_HCMD_DFL_NOCOPY; |
| 892 |
scan->len = cpu_to_le16(cmd.len[0]); |
| 893 |
|
| 894 |
/* set scan bit here for PAN params */ |
| 895 |
set_bit(STATUS_SCAN_HW, &priv->status); |
| 896 |
|
| 897 |
ret = iwlagn_set_pan_params(priv); |
| 898 |
if (ret) { |
| 899 |
clear_bit(STATUS_SCAN_HW, &priv->status); |
| 900 |
return ret; |
| 901 |
} |
| 902 |
|
| 903 |
ret = iwl_dvm_send_cmd(priv, &cmd); |
| 904 |
if (ret) { |
| 905 |
clear_bit(STATUS_SCAN_HW, &priv->status); |
| 906 |
iwlagn_set_pan_params(priv); |
| 907 |
} |
| 908 |
|
| 909 |
return ret; |
| 910 |
} |
| 911 |
|
| 912 |
void iwl_init_scan_params(struct iwl_priv *priv) |
| 913 |
{ |
| 914 |
u8 ant_idx = fls(priv->nvm_data->valid_tx_ant) - 1; |
| 915 |
if (!priv->scan_tx_ant[NL80211_BAND_5GHZ]) |
| 916 |
priv->scan_tx_ant[NL80211_BAND_5GHZ] = ant_idx; |
| 917 |
if (!priv->scan_tx_ant[NL80211_BAND_2GHZ]) |
| 918 |
priv->scan_tx_ant[NL80211_BAND_2GHZ] = ant_idx; |
| 919 |
} |
| 920 |
|
| 921 |
int __must_check iwl_scan_initiate(struct iwl_priv *priv, |
| 922 |
struct ieee80211_vif *vif, |
| 923 |
enum iwl_scan_type scan_type, |
| 924 |
enum nl80211_band band) |
| 925 |
{ |
| 926 |
int ret; |
| 927 |
|
| 928 |
lockdep_assert_held(&priv->mutex); |
| 929 |
|
| 930 |
cancel_delayed_work(&priv->scan_check); |
| 931 |
|
| 932 |
if (!iwl_is_ready_rf(priv)) { |
| 933 |
IWL_WARN(priv, "Request scan called when driver not ready.\n"); |
| 934 |
return -EIO; |
| 935 |
} |
| 936 |
|
| 937 |
if (test_bit(STATUS_SCAN_HW, &priv->status)) { |
| 938 |
IWL_DEBUG_SCAN(priv, |
| 939 |
"Multiple concurrent scan requests in parallel.\n"); |
| 940 |
return -EBUSY; |
| 941 |
} |
| 942 |
|
| 943 |
if (test_bit(STATUS_SCAN_ABORTING, &priv->status)) { |
| 944 |
IWL_DEBUG_SCAN(priv, "Scan request while abort pending.\n"); |
| 945 |
return -EBUSY; |
| 946 |
} |
| 947 |
|
| 948 |
IWL_DEBUG_SCAN(priv, "Starting %sscan...\n", |
| 949 |
scan_type == IWL_SCAN_NORMAL ? "" : |
| 950 |
"internal short "); |
| 951 |
|
| 952 |
set_bit(STATUS_SCANNING, &priv->status); |
| 953 |
priv->scan_type = scan_type; |
| 954 |
priv->scan_start = jiffies; |
| 955 |
priv->scan_band = band; |
| 956 |
|
| 957 |
ret = iwlagn_request_scan(priv, vif); |
| 958 |
if (ret) { |
| 959 |
clear_bit(STATUS_SCANNING, &priv->status); |
| 960 |
priv->scan_type = IWL_SCAN_NORMAL; |
| 961 |
return ret; |
| 962 |
} |
| 963 |
|
| 964 |
queue_delayed_work(priv->workqueue, &priv->scan_check, |
| 965 |
IWL_SCAN_CHECK_WATCHDOG); |
| 966 |
|
| 967 |
return 0; |
| 968 |
} |
| 969 |
|
| 970 |
|
| 971 |
/* |
| 972 |
* internal short scan, this function should only been called while associated. |
| 973 |
* It will reset and tune the radio to prevent possible RF related problem |
| 974 |
*/ |
| 975 |
void iwl_internal_short_hw_scan(struct iwl_priv *priv) |
| 976 |
{ |
| 977 |
queue_work(priv->workqueue, &priv->start_internal_scan); |
| 978 |
} |
| 979 |
|
| 980 |
static void iwl_bg_start_internal_scan(struct work_struct *work) |
| 981 |
{ |
| 982 |
struct iwl_priv *priv = |
| 983 |
container_of(work, struct iwl_priv, start_internal_scan); |
| 984 |
|
| 985 |
IWL_DEBUG_SCAN(priv, "Start internal scan\n"); |
| 986 |
|
| 987 |
mutex_lock(&priv->mutex); |
| 988 |
|
| 989 |
if (priv->scan_type == IWL_SCAN_RADIO_RESET) { |
| 990 |
IWL_DEBUG_SCAN(priv, "Internal scan already in progress\n"); |
| 991 |
goto unlock; |
| 992 |
} |
| 993 |
|
| 994 |
if (test_bit(STATUS_SCANNING, &priv->status)) { |
| 995 |
IWL_DEBUG_SCAN(priv, "Scan already in progress.\n"); |
| 996 |
goto unlock; |
| 997 |
} |
| 998 |
|
| 999 |
if (iwl_scan_initiate(priv, NULL, IWL_SCAN_RADIO_RESET, priv->band)) |
| 1000 |
IWL_DEBUG_SCAN(priv, "failed to start internal short scan\n"); |
| 1001 |
unlock: |
| 1002 |
mutex_unlock(&priv->mutex); |
| 1003 |
} |
| 1004 |
|
| 1005 |
static void iwl_bg_scan_check(struct work_struct *data) |
| 1006 |
{ |
| 1007 |
struct iwl_priv *priv = |
| 1008 |
container_of(data, struct iwl_priv, scan_check.work); |
| 1009 |
|
| 1010 |
IWL_DEBUG_SCAN(priv, "Scan check work\n"); |
| 1011 |
|
| 1012 |
/* Since we are here firmware does not finish scan and |
| 1013 |
* most likely is in bad shape, so we don't bother to |
| 1014 |
* send abort command, just force scan complete to mac80211 */ |
| 1015 |
mutex_lock(&priv->mutex); |
| 1016 |
iwl_force_scan_end(priv); |
| 1017 |
mutex_unlock(&priv->mutex); |
| 1018 |
} |
| 1019 |
|
| 1020 |
static void iwl_bg_abort_scan(struct work_struct *work) |
| 1021 |
{ |
| 1022 |
struct iwl_priv *priv = container_of(work, struct iwl_priv, abort_scan); |
| 1023 |
|
| 1024 |
IWL_DEBUG_SCAN(priv, "Abort scan work\n"); |
| 1025 |
|
| 1026 |
/* We keep scan_check work queued in case when firmware will not |
| 1027 |
* report back scan completed notification */ |
| 1028 |
mutex_lock(&priv->mutex); |
| 1029 |
iwl_scan_cancel_timeout(priv, 200); |
| 1030 |
mutex_unlock(&priv->mutex); |
| 1031 |
} |
| 1032 |
|
| 1033 |
static void iwl_bg_scan_completed(struct work_struct *work) |
| 1034 |
{ |
| 1035 |
struct iwl_priv *priv = |
| 1036 |
container_of(work, struct iwl_priv, scan_completed); |
| 1037 |
|
| 1038 |
mutex_lock(&priv->mutex); |
| 1039 |
iwl_process_scan_complete(priv); |
| 1040 |
mutex_unlock(&priv->mutex); |
| 1041 |
} |
| 1042 |
|
| 1043 |
void iwl_setup_scan_deferred_work(struct iwl_priv *priv) |
| 1044 |
{ |
| 1045 |
INIT_WORK(&priv->scan_completed, iwl_bg_scan_completed); |
| 1046 |
INIT_WORK(&priv->abort_scan, iwl_bg_abort_scan); |
| 1047 |
INIT_WORK(&priv->start_internal_scan, iwl_bg_start_internal_scan); |
| 1048 |
INIT_DELAYED_WORK(&priv->scan_check, iwl_bg_scan_check); |
| 1049 |
} |
| 1050 |
|
| 1051 |
void iwl_cancel_scan_deferred_work(struct iwl_priv *priv) |
| 1052 |
{ |
| 1053 |
cancel_work_sync(&priv->start_internal_scan); |
| 1054 |
cancel_work_sync(&priv->abort_scan); |
| 1055 |
cancel_work_sync(&priv->scan_completed); |
| 1056 |
|
| 1057 |
if (cancel_delayed_work_sync(&priv->scan_check)) { |
| 1058 |
mutex_lock(&priv->mutex); |
| 1059 |
iwl_force_scan_end(priv); |
| 1060 |
mutex_unlock(&priv->mutex); |
| 1061 |
} |
| 1062 |
} |