| 1 |
# SPDX-License-Identifier: GPL-2.0-only |
| 2 |
config IR_IMG |
| 3 |
tristate "ImgTec IR Decoder" |
| 4 |
depends on RC_CORE |
| 5 |
depends on MIPS || COMPILE_TEST |
| 6 |
select IR_IMG_HW if !IR_IMG_RAW |
| 7 |
help |
| 8 |
Say Y or M here if you want to use the ImgTec infrared decoder |
| 9 |
functionality found in SoCs such as TZ1090. |
| 10 |
|
| 11 |
config IR_IMG_RAW |
| 12 |
bool "Raw decoder" |
| 13 |
depends on IR_IMG |
| 14 |
help |
| 15 |
Say Y here to enable the raw mode driver which passes raw IR signal |
| 16 |
changes to the IR raw decoders for software decoding. This is much |
| 17 |
less reliable (due to lack of timestamps) and consumes more |
| 18 |
processing power than using hardware decode, but can be useful for |
| 19 |
testing, debug, and to make more protocols available. |
| 20 |
|
| 21 |
config IR_IMG_HW |
| 22 |
bool "Hardware decoder" |
| 23 |
depends on IR_IMG |
| 24 |
help |
| 25 |
Say Y here to enable the hardware decode driver which decodes the IR |
| 26 |
signals in hardware. This is more reliable, consumes less processing |
| 27 |
power since only a single interrupt is received for each scancode, |
| 28 |
and allows an IR scancode to be used as a wake event. |
| 29 |
|
| 30 |
config IR_IMG_NEC |
| 31 |
bool "NEC protocol support" |
| 32 |
depends on IR_IMG_HW |
| 33 |
select BITREVERSE |
| 34 |
help |
| 35 |
Say Y here to enable support for the NEC, extended NEC, and 32-bit |
| 36 |
NEC protocols in the ImgTec infrared decoder block. |
| 37 |
|
| 38 |
config IR_IMG_JVC |
| 39 |
bool "JVC protocol support" |
| 40 |
depends on IR_IMG_HW |
| 41 |
help |
| 42 |
Say Y here to enable support for the JVC protocol in the ImgTec |
| 43 |
infrared decoder block. |
| 44 |
|
| 45 |
config IR_IMG_SONY |
| 46 |
bool "Sony protocol support" |
| 47 |
depends on IR_IMG_HW |
| 48 |
help |
| 49 |
Say Y here to enable support for the Sony protocol in the ImgTec |
| 50 |
infrared decoder block. |
| 51 |
|
| 52 |
config IR_IMG_SHARP |
| 53 |
bool "Sharp protocol support" |
| 54 |
depends on IR_IMG_HW |
| 55 |
help |
| 56 |
Say Y here to enable support for the Sharp protocol in the ImgTec |
| 57 |
infrared decoder block. |
| 58 |
|
| 59 |
config IR_IMG_SANYO |
| 60 |
bool "Sanyo protocol support" |
| 61 |
depends on IR_IMG_HW |
| 62 |
help |
| 63 |
Say Y here to enable support for the Sanyo protocol (used by Sanyo, |
| 64 |
Aiwa, Chinon remotes) in the ImgTec infrared decoder block. |
| 65 |
|
| 66 |
config IR_IMG_RC5 |
| 67 |
bool "Philips RC5 protocol support" |
| 68 |
depends on IR_IMG_HW |
| 69 |
help |
| 70 |
Say Y here to enable support for the RC5 protocol in the ImgTec |
| 71 |
infrared decoder block. |
| 72 |
|
| 73 |
config IR_IMG_RC6 |
| 74 |
bool "Philips RC6 protocol support" |
| 75 |
depends on IR_IMG_HW |
| 76 |
help |
| 77 |
Say Y here to enable support for the RC6 protocol in the ImgTec |
| 78 |
infrared decoder block. |
| 79 |
Note: This version only supports mode 0. |