| 1 |
.. SPDX-License-Identifier: GFDL-1.1-no-invariants-or-later |
| 2 |
|
| 3 |
.. _fe_property_parameters: |
| 4 |
|
| 5 |
****************************** |
| 6 |
Digital TV property parameters |
| 7 |
****************************** |
| 8 |
|
| 9 |
There are several different Digital TV parameters that can be used by |
| 10 |
:ref:`FE_SET_PROPERTY and FE_GET_PROPERTY ioctls<FE_GET_PROPERTY>`. |
| 11 |
This section describes each of them. Please notice, however, that only |
| 12 |
a subset of them are needed to setup a frontend. |
| 13 |
|
| 14 |
|
| 15 |
.. _DTV-UNDEFINED: |
| 16 |
|
| 17 |
DTV_UNDEFINED |
| 18 |
============= |
| 19 |
|
| 20 |
Used internally. A GET/SET operation for it won't change or return |
| 21 |
anything. |
| 22 |
|
| 23 |
|
| 24 |
.. _DTV-TUNE: |
| 25 |
|
| 26 |
DTV_TUNE |
| 27 |
======== |
| 28 |
|
| 29 |
Interpret the cache of data, build either a traditional frontend |
| 30 |
tunerequest so we can pass validation in the ``FE_SET_FRONTEND`` ioctl. |
| 31 |
|
| 32 |
|
| 33 |
.. _DTV-CLEAR: |
| 34 |
|
| 35 |
DTV_CLEAR |
| 36 |
========= |
| 37 |
|
| 38 |
Reset a cache of data specific to the frontend here. This does not |
| 39 |
effect hardware. |
| 40 |
|
| 41 |
|
| 42 |
.. _DTV-FREQUENCY: |
| 43 |
|
| 44 |
DTV_FREQUENCY |
| 45 |
============= |
| 46 |
|
| 47 |
Frequency of the digital TV transponder/channel. |
| 48 |
|
| 49 |
.. note:: |
| 50 |
|
| 51 |
#. For satellite delivery systems, the frequency is in kHz. |
| 52 |
|
| 53 |
#. For cable and terrestrial delivery systems, the frequency is in |
| 54 |
Hz. |
| 55 |
|
| 56 |
#. On most delivery systems, the frequency is the center frequency |
| 57 |
of the transponder/channel. The exception is for ISDB-T, where |
| 58 |
the main carrier has a 1/7 offset from the center. |
| 59 |
|
| 60 |
#. For ISDB-T, the channels are usually transmitted with an offset of |
| 61 |
about 143kHz. E.g. a valid frequency could be 474,143 kHz. The |
| 62 |
stepping is bound to the bandwidth of the channel which is |
| 63 |
typically 6MHz. |
| 64 |
|
| 65 |
#. In ISDB-Tsb, the channel consists of only one or three segments the |
| 66 |
frequency step is 429kHz, 3*429 respectively. |
| 67 |
|
| 68 |
|
| 69 |
.. _DTV-MODULATION: |
| 70 |
|
| 71 |
DTV_MODULATION |
| 72 |
============== |
| 73 |
|
| 74 |
Specifies the frontend modulation type for delivery systems that |
| 75 |
support multiple modulations. |
| 76 |
|
| 77 |
The modulation can be one of the types defined by enum :c:type:`fe_modulation`. |
| 78 |
|
| 79 |
Most of the digital TV standards offer more than one possible |
| 80 |
modulation type. |
| 81 |
|
| 82 |
The table below presents a summary of the types of modulation types |
| 83 |
supported by each delivery system, as currently defined by specs. |
| 84 |
|
| 85 |
======================= ======================================================= |
| 86 |
Standard Modulation types |
| 87 |
======================= ======================================================= |
| 88 |
ATSC (version 1) 8-VSB and 16-VSB. |
| 89 |
DMTB 4-QAM, 16-QAM, 32-QAM, 64-QAM and 4-QAM-NR. |
| 90 |
DVB-C Annex A/C 16-QAM, 32-QAM, 64-QAM and 256-QAM. |
| 91 |
DVB-C Annex B 64-QAM. |
| 92 |
DVB-C2 QPSK, 16-QAM, 64-QAM, 256-QAM, 1024-QAM and 4096-QAM. |
| 93 |
DVB-T QPSK, 16-QAM and 64-QAM. |
| 94 |
DVB-T2 QPSK, 16-QAM, 64-QAM and 256-QAM. |
| 95 |
DVB-S No need to set. It supports only QPSK. |
| 96 |
DVB-S2 QPSK, 8-PSK, 16-APSK and 32-APSK. |
| 97 |
DVB-S2X 8-APSK-L, 16-APSK-L, 32-APSK-L, 64-APSK and 64-APSK-L. |
| 98 |
ISDB-T QPSK, DQPSK, 16-QAM and 64-QAM. |
| 99 |
ISDB-S 8-PSK, QPSK and BPSK. |
| 100 |
======================= ======================================================= |
| 101 |
|
| 102 |
.. note:: |
| 103 |
|
| 104 |
As DVB-S2X specifies extensions to the DVB-S2 standard, the same |
| 105 |
delivery system enum value is used (SYS_DVBS2). |
| 106 |
|
| 107 |
Please notice that some of the above modulation types may not be |
| 108 |
defined currently at the Kernel. The reason is simple: no driver |
| 109 |
needed such definition yet. |
| 110 |
|
| 111 |
|
| 112 |
.. _DTV-BANDWIDTH-HZ: |
| 113 |
|
| 114 |
DTV_BANDWIDTH_HZ |
| 115 |
================ |
| 116 |
|
| 117 |
Bandwidth for the channel, in HZ. |
| 118 |
|
| 119 |
Should be set only for terrestrial delivery systems. |
| 120 |
|
| 121 |
Possible values: ``1712000``, ``5000000``, ``6000000``, ``7000000``, |
| 122 |
``8000000``, ``10000000``. |
| 123 |
|
| 124 |
======================= ======================================================= |
| 125 |
Terrestrial Standard Possible values for bandwidth |
| 126 |
======================= ======================================================= |
| 127 |
ATSC (version 1) No need to set. It is always 6MHz. |
| 128 |
DMTB No need to set. It is always 8MHz. |
| 129 |
DVB-T 6MHz, 7MHz and 8MHz. |
| 130 |
DVB-T2 1.172 MHz, 5MHz, 6MHz, 7MHz, 8MHz and 10MHz |
| 131 |
ISDB-T 5MHz, 6MHz, 7MHz and 8MHz, although most places |
| 132 |
use 6MHz. |
| 133 |
======================= ======================================================= |
| 134 |
|
| 135 |
|
| 136 |
.. note:: |
| 137 |
|
| 138 |
|
| 139 |
#. For ISDB-Tsb, the bandwidth can vary depending on the number of |
| 140 |
connected segments. |
| 141 |
|
| 142 |
It can be easily derived from other parameters |
| 143 |
(DTV_ISDBT_SB_SEGMENT_IDX, DTV_ISDBT_SB_SEGMENT_COUNT). |
| 144 |
|
| 145 |
#. On Satellite and Cable delivery systems, the bandwidth depends on |
| 146 |
the symbol rate. The kernel will silently ignore any :ref:`DTV-BANDWIDTH-HZ` |
| 147 |
setting and overwrites it with bandwidth estimation. |
| 148 |
|
| 149 |
Such bandwidth estimation takes into account the symbol rate set with |
| 150 |
:ref:`DTV-SYMBOL-RATE`, and the rolloff factor, with is fixed for |
| 151 |
DVB-C and DVB-S. |
| 152 |
|
| 153 |
For DVB-S2, the rolloff should also be set via :ref:`DTV-ROLLOFF`. |
| 154 |
|
| 155 |
|
| 156 |
.. _DTV-INVERSION: |
| 157 |
|
| 158 |
DTV_INVERSION |
| 159 |
============= |
| 160 |
|
| 161 |
Specifies if the frontend should do spectral inversion or not. |
| 162 |
|
| 163 |
The acceptable values are defined by :c:type:`fe_spectral_inversion`. |
| 164 |
|
| 165 |
|
| 166 |
.. _DTV-DISEQC-MASTER: |
| 167 |
|
| 168 |
DTV_DISEQC_MASTER |
| 169 |
================= |
| 170 |
|
| 171 |
Currently not implemented. |
| 172 |
|
| 173 |
|
| 174 |
.. _DTV-SYMBOL-RATE: |
| 175 |
|
| 176 |
DTV_SYMBOL_RATE |
| 177 |
=============== |
| 178 |
|
| 179 |
Used on cable and satellite delivery systems. |
| 180 |
|
| 181 |
Digital TV symbol rate, in bauds (symbols/second). |
| 182 |
|
| 183 |
|
| 184 |
.. _DTV-INNER-FEC: |
| 185 |
|
| 186 |
DTV_INNER_FEC |
| 187 |
============= |
| 188 |
|
| 189 |
Used on cable and satellite delivery systems. |
| 190 |
|
| 191 |
The acceptable values are defined by :c:type:`fe_code_rate`. |
| 192 |
|
| 193 |
|
| 194 |
.. _DTV-VOLTAGE: |
| 195 |
|
| 196 |
DTV_VOLTAGE |
| 197 |
=========== |
| 198 |
|
| 199 |
Used on satellite delivery systems. |
| 200 |
|
| 201 |
The voltage is usually used with non-DiSEqC capable LNBs to switch the |
| 202 |
polarization (horizontal/vertical). When using DiSEqC equipment this |
| 203 |
voltage has to be switched consistently to the DiSEqC commands as |
| 204 |
described in the DiSEqC spec. |
| 205 |
|
| 206 |
The acceptable values are defined by :c:type:`fe_sec_voltage`. |
| 207 |
|
| 208 |
|
| 209 |
.. _DTV-TONE: |
| 210 |
|
| 211 |
DTV_TONE |
| 212 |
======== |
| 213 |
|
| 214 |
Currently not used. |
| 215 |
|
| 216 |
|
| 217 |
.. _DTV-PILOT: |
| 218 |
|
| 219 |
DTV_PILOT |
| 220 |
========= |
| 221 |
|
| 222 |
Used on DVB-S2. |
| 223 |
|
| 224 |
Sets DVB-S2 pilot. |
| 225 |
|
| 226 |
The acceptable values are defined by :c:type:`fe_pilot`. |
| 227 |
|
| 228 |
|
| 229 |
.. _DTV-ROLLOFF: |
| 230 |
|
| 231 |
DTV_ROLLOFF |
| 232 |
=========== |
| 233 |
|
| 234 |
Used on DVB-S2. |
| 235 |
|
| 236 |
Sets DVB-S2 rolloff. |
| 237 |
|
| 238 |
The acceptable values are defined by :c:type:`fe_rolloff`. |
| 239 |
|
| 240 |
|
| 241 |
.. _DTV-DISEQC-SLAVE-REPLY: |
| 242 |
|
| 243 |
DTV_DISEQC_SLAVE_REPLY |
| 244 |
====================== |
| 245 |
|
| 246 |
Currently not implemented. |
| 247 |
|
| 248 |
|
| 249 |
.. _DTV-FE-CAPABILITY-COUNT: |
| 250 |
|
| 251 |
DTV_FE_CAPABILITY_COUNT |
| 252 |
======================= |
| 253 |
|
| 254 |
Currently not implemented. |
| 255 |
|
| 256 |
|
| 257 |
.. _DTV-FE-CAPABILITY: |
| 258 |
|
| 259 |
DTV_FE_CAPABILITY |
| 260 |
================= |
| 261 |
|
| 262 |
Currently not implemented. |
| 263 |
|
| 264 |
|
| 265 |
.. _DTV-DELIVERY-SYSTEM: |
| 266 |
|
| 267 |
DTV_DELIVERY_SYSTEM |
| 268 |
=================== |
| 269 |
|
| 270 |
Specifies the type of the delivery system. |
| 271 |
|
| 272 |
The acceptable values are defined by :c:type:`fe_delivery_system`. |
| 273 |
|
| 274 |
|
| 275 |
.. _DTV-ISDBT-PARTIAL-RECEPTION: |
| 276 |
|
| 277 |
DTV_ISDBT_PARTIAL_RECEPTION |
| 278 |
=========================== |
| 279 |
|
| 280 |
Used only on ISDB. |
| 281 |
|
| 282 |
If ``DTV_ISDBT_SOUND_BROADCASTING`` is '0' this bit field represents |
| 283 |
whether the channel is in partial reception mode or not. |
| 284 |
|
| 285 |
If '1' ``DTV_ISDBT_LAYERA_*`` values are assigned to the center segment |
| 286 |
and ``DTV_ISDBT_LAYERA_SEGMENT_COUNT`` has to be '1'. |
| 287 |
|
| 288 |
If in addition ``DTV_ISDBT_SOUND_BROADCASTING`` is '1' |
| 289 |
``DTV_ISDBT_PARTIAL_RECEPTION`` represents whether this ISDB-Tsb channel |
| 290 |
is consisting of one segment and layer or three segments and two layers. |
| 291 |
|
| 292 |
Possible values: 0, 1, -1 (AUTO) |
| 293 |
|
| 294 |
|
| 295 |
.. _DTV-ISDBT-SOUND-BROADCASTING: |
| 296 |
|
| 297 |
DTV_ISDBT_SOUND_BROADCASTING |
| 298 |
============================ |
| 299 |
|
| 300 |
Used only on ISDB. |
| 301 |
|
| 302 |
This field represents whether the other DTV_ISDBT_*-parameters are |
| 303 |
referring to an ISDB-T and an ISDB-Tsb channel. (See also |
| 304 |
``DTV_ISDBT_PARTIAL_RECEPTION``). |
| 305 |
|
| 306 |
Possible values: 0, 1, -1 (AUTO) |
| 307 |
|
| 308 |
|
| 309 |
.. _DTV-ISDBT-SB-SUBCHANNEL-ID: |
| 310 |
|
| 311 |
DTV_ISDBT_SB_SUBCHANNEL_ID |
| 312 |
========================== |
| 313 |
|
| 314 |
Used only on ISDB. |
| 315 |
|
| 316 |
This field only applies if ``DTV_ISDBT_SOUND_BROADCASTING`` is '1'. |
| 317 |
|
| 318 |
(Note of the author: This might not be the correct description of the |
| 319 |
``SUBCHANNEL-ID`` in all details, but it is my understanding of the |
| 320 |
technical background needed to program a device) |
| 321 |
|
| 322 |
An ISDB-Tsb channel (1 or 3 segments) can be broadcasted alone or in a |
| 323 |
set of connected ISDB-Tsb channels. In this set of channels every |
| 324 |
channel can be received independently. The number of connected ISDB-Tsb |
| 325 |
segment can vary, e.g. depending on the frequency spectrum bandwidth |
| 326 |
available. |
| 327 |
|
| 328 |
Example: Assume 8 ISDB-Tsb connected segments are broadcasted. The |
| 329 |
broadcaster has several possibilities to put those channels in the air: |
| 330 |
Assuming a normal 13-segment ISDB-T spectrum he can align the 8 segments |
| 331 |
from position 1-8 to 5-13 or anything in between. |
| 332 |
|
| 333 |
The underlying layer of segments are sub-channels: each segment is |
| 334 |
consisting of several sub-channels with a predefined IDs. A sub-channel |
| 335 |
is used to help the demodulator to synchronize on the channel. |
| 336 |
|
| 337 |
An ISDB-T channel is always centered over all sub-channels. As for the |
| 338 |
example above, in ISDB-Tsb it is no longer as simple as that. |
| 339 |
|
| 340 |
``The DTV_ISDBT_SB_SUBCHANNEL_ID`` parameter is used to give the |
| 341 |
sub-channel ID of the segment to be demodulated. |
| 342 |
|
| 343 |
Possible values: 0 .. 41, -1 (AUTO) |
| 344 |
|
| 345 |
|
| 346 |
.. _DTV-ISDBT-SB-SEGMENT-IDX: |
| 347 |
|
| 348 |
DTV_ISDBT_SB_SEGMENT_IDX |
| 349 |
======================== |
| 350 |
|
| 351 |
Used only on ISDB. |
| 352 |
|
| 353 |
This field only applies if ``DTV_ISDBT_SOUND_BROADCASTING`` is '1'. |
| 354 |
|
| 355 |
``DTV_ISDBT_SB_SEGMENT_IDX`` gives the index of the segment to be |
| 356 |
demodulated for an ISDB-Tsb channel where several of them are |
| 357 |
transmitted in the connected manner. |
| 358 |
|
| 359 |
Possible values: 0 .. ``DTV_ISDBT_SB_SEGMENT_COUNT`` - 1 |
| 360 |
|
| 361 |
Note: This value cannot be determined by an automatic channel search. |
| 362 |
|
| 363 |
|
| 364 |
.. _DTV-ISDBT-SB-SEGMENT-COUNT: |
| 365 |
|
| 366 |
DTV_ISDBT_SB_SEGMENT_COUNT |
| 367 |
========================== |
| 368 |
|
| 369 |
Used only on ISDB. |
| 370 |
|
| 371 |
This field only applies if ``DTV_ISDBT_SOUND_BROADCASTING`` is '1'. |
| 372 |
|
| 373 |
``DTV_ISDBT_SB_SEGMENT_COUNT`` gives the total count of connected |
| 374 |
ISDB-Tsb channels. |
| 375 |
|
| 376 |
Possible values: 1 .. 13 |
| 377 |
|
| 378 |
Note: This value cannot be determined by an automatic channel search. |
| 379 |
|
| 380 |
|
| 381 |
.. _isdb-hierq-layers: |
| 382 |
|
| 383 |
DTV-ISDBT-LAYER[A-C] parameters |
| 384 |
=============================== |
| 385 |
|
| 386 |
Used only on ISDB. |
| 387 |
|
| 388 |
ISDB-T channels can be coded hierarchically. As opposed to DVB-T in |
| 389 |
ISDB-T hierarchical layers can be decoded simultaneously. For that |
| 390 |
reason a ISDB-T demodulator has 3 Viterbi and 3 Reed-Solomon decoders. |
| 391 |
|
| 392 |
ISDB-T has 3 hierarchical layers which each can use a part of the |
| 393 |
available segments. The total number of segments over all layers has to |
| 394 |
13 in ISDB-T. |
| 395 |
|
| 396 |
There are 3 parameter sets, for Layers A, B and C. |
| 397 |
|
| 398 |
|
| 399 |
.. _DTV-ISDBT-LAYER-ENABLED: |
| 400 |
|
| 401 |
DTV_ISDBT_LAYER_ENABLED |
| 402 |
----------------------- |
| 403 |
|
| 404 |
Used only on ISDB. |
| 405 |
|
| 406 |
Hierarchical reception in ISDB-T is achieved by enabling or disabling |
| 407 |
layers in the decoding process. Setting all bits of |
| 408 |
``DTV_ISDBT_LAYER_ENABLED`` to '1' forces all layers (if applicable) to |
| 409 |
be demodulated. This is the default. |
| 410 |
|
| 411 |
If the channel is in the partial reception mode |
| 412 |
(``DTV_ISDBT_PARTIAL_RECEPTION`` = 1) the central segment can be decoded |
| 413 |
independently of the other 12 segments. In that mode layer A has to have |
| 414 |
a ``SEGMENT_COUNT`` of 1. |
| 415 |
|
| 416 |
In ISDB-Tsb only layer A is used, it can be 1 or 3 in ISDB-Tsb according |
| 417 |
to ``DTV_ISDBT_PARTIAL_RECEPTION``. ``SEGMENT_COUNT`` must be filled |
| 418 |
accordingly. |
| 419 |
|
| 420 |
Only the values of the first 3 bits are used. Other bits will be silently ignored: |
| 421 |
|
| 422 |
``DTV_ISDBT_LAYER_ENABLED`` bit 0: layer A enabled |
| 423 |
|
| 424 |
``DTV_ISDBT_LAYER_ENABLED`` bit 1: layer B enabled |
| 425 |
|
| 426 |
``DTV_ISDBT_LAYER_ENABLED`` bit 2: layer C enabled |
| 427 |
|
| 428 |
``DTV_ISDBT_LAYER_ENABLED`` bits 3-31: unused |
| 429 |
|
| 430 |
|
| 431 |
.. _DTV-ISDBT-LAYER-FEC: |
| 432 |
|
| 433 |
DTV_ISDBT_LAYER[A-C]_FEC |
| 434 |
------------------------ |
| 435 |
|
| 436 |
Used only on ISDB. |
| 437 |
|
| 438 |
The Forward Error Correction mechanism used by a given ISDB Layer, as |
| 439 |
defined by :c:type:`fe_code_rate`. |
| 440 |
|
| 441 |
|
| 442 |
Possible values are: ``FEC_AUTO``, ``FEC_1_2``, ``FEC_2_3``, ``FEC_3_4``, |
| 443 |
``FEC_5_6``, ``FEC_7_8`` |
| 444 |
|
| 445 |
|
| 446 |
.. _DTV-ISDBT-LAYER-MODULATION: |
| 447 |
|
| 448 |
DTV_ISDBT_LAYER[A-C]_MODULATION |
| 449 |
------------------------------- |
| 450 |
|
| 451 |
Used only on ISDB. |
| 452 |
|
| 453 |
The modulation used by a given ISDB Layer, as defined by |
| 454 |
:c:type:`fe_modulation`. |
| 455 |
|
| 456 |
Possible values are: ``QAM_AUTO``, ``QPSK``, ``QAM_16``, ``QAM_64``, ``DQPSK`` |
| 457 |
|
| 458 |
.. note:: |
| 459 |
|
| 460 |
#. If layer C is ``DQPSK``, then layer B has to be ``DQPSK``. |
| 461 |
|
| 462 |
#. If layer B is ``DQPSK`` and ``DTV_ISDBT_PARTIAL_RECEPTION``\ = 0, |
| 463 |
then layer has to be ``DQPSK``. |
| 464 |
|
| 465 |
|
| 466 |
.. _DTV-ISDBT-LAYER-SEGMENT-COUNT: |
| 467 |
|
| 468 |
DTV_ISDBT_LAYER[A-C]_SEGMENT_COUNT |
| 469 |
---------------------------------- |
| 470 |
|
| 471 |
Used only on ISDB. |
| 472 |
|
| 473 |
Possible values: 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 13, -1 (AUTO) |
| 474 |
|
| 475 |
Note: Truth table for ``DTV_ISDBT_SOUND_BROADCASTING`` and |
| 476 |
``DTV_ISDBT_PARTIAL_RECEPTION`` and ``LAYER[A-C]_SEGMENT_COUNT`` |
| 477 |
|
| 478 |
.. _isdbt-layer_seg-cnt-table: |
| 479 |
|
| 480 |
.. flat-table:: Truth table for ISDB-T Sound Broadcasting |
| 481 |
:header-rows: 1 |
| 482 |
:stub-columns: 0 |
| 483 |
|
| 484 |
|
| 485 |
- .. row 1 |
| 486 |
|
| 487 |
- Partial Reception |
| 488 |
|
| 489 |
- Sound Broadcasting |
| 490 |
|
| 491 |
- Layer A width |
| 492 |
|
| 493 |
- Layer B width |
| 494 |
|
| 495 |
- Layer C width |
| 496 |
|
| 497 |
- total width |
| 498 |
|
| 499 |
- .. row 2 |
| 500 |
|
| 501 |
- 0 |
| 502 |
|
| 503 |
- 0 |
| 504 |
|
| 505 |
- 1 .. 13 |
| 506 |
|
| 507 |
- 1 .. 13 |
| 508 |
|
| 509 |
- 1 .. 13 |
| 510 |
|
| 511 |
- 13 |
| 512 |
|
| 513 |
- .. row 3 |
| 514 |
|
| 515 |
- 1 |
| 516 |
|
| 517 |
- 0 |
| 518 |
|
| 519 |
- 1 |
| 520 |
|
| 521 |
- 1 .. 13 |
| 522 |
|
| 523 |
- 1 .. 13 |
| 524 |
|
| 525 |
- 13 |
| 526 |
|
| 527 |
- .. row 4 |
| 528 |
|
| 529 |
- 0 |
| 530 |
|
| 531 |
- 1 |
| 532 |
|
| 533 |
- 1 |
| 534 |
|
| 535 |
- 0 |
| 536 |
|
| 537 |
- 0 |
| 538 |
|
| 539 |
- 1 |
| 540 |
|
| 541 |
- .. row 5 |
| 542 |
|
| 543 |
- 1 |
| 544 |
|
| 545 |
- 1 |
| 546 |
|
| 547 |
- 1 |
| 548 |
|
| 549 |
- 2 |
| 550 |
|
| 551 |
- 0 |
| 552 |
|
| 553 |
- 13 |
| 554 |
|
| 555 |
|
| 556 |
|
| 557 |
.. _DTV-ISDBT-LAYER-TIME-INTERLEAVING: |
| 558 |
|
| 559 |
DTV_ISDBT_LAYER[A-C]_TIME_INTERLEAVING |
| 560 |
-------------------------------------- |
| 561 |
|
| 562 |
Used only on ISDB. |
| 563 |
|
| 564 |
Valid values: 0, 1, 2, 4, -1 (AUTO) |
| 565 |
|
| 566 |
when DTV_ISDBT_SOUND_BROADCASTING is active, value 8 is also valid. |
| 567 |
|
| 568 |
Note: The real time interleaving length depends on the mode (fft-size). |
| 569 |
The values here are referring to what can be found in the |
| 570 |
TMCC-structure, as shown in the table below. |
| 571 |
|
| 572 |
|
| 573 |
.. c:type:: isdbt_layer_interleaving_table |
| 574 |
|
| 575 |
.. flat-table:: ISDB-T time interleaving modes |
| 576 |
:header-rows: 1 |
| 577 |
:stub-columns: 0 |
| 578 |
|
| 579 |
|
| 580 |
- .. row 1 |
| 581 |
|
| 582 |
- ``DTV_ISDBT_LAYER[A-C]_TIME_INTERLEAVING`` |
| 583 |
|
| 584 |
- Mode 1 (2K FFT) |
| 585 |
|
| 586 |
- Mode 2 (4K FFT) |
| 587 |
|
| 588 |
- Mode 3 (8K FFT) |
| 589 |
|
| 590 |
- .. row 2 |
| 591 |
|
| 592 |
- 0 |
| 593 |
|
| 594 |
- 0 |
| 595 |
|
| 596 |
- 0 |
| 597 |
|
| 598 |
- 0 |
| 599 |
|
| 600 |
- .. row 3 |
| 601 |
|
| 602 |
- 1 |
| 603 |
|
| 604 |
- 4 |
| 605 |
|
| 606 |
- 2 |
| 607 |
|
| 608 |
- 1 |
| 609 |
|
| 610 |
- .. row 4 |
| 611 |
|
| 612 |
- 2 |
| 613 |
|
| 614 |
- 8 |
| 615 |
|
| 616 |
- 4 |
| 617 |
|
| 618 |
- 2 |
| 619 |
|
| 620 |
- .. row 5 |
| 621 |
|
| 622 |
- 4 |
| 623 |
|
| 624 |
- 16 |
| 625 |
|
| 626 |
- 8 |
| 627 |
|
| 628 |
- 4 |
| 629 |
|
| 630 |
|
| 631 |
|
| 632 |
.. _DTV-ATSCMH-FIC-VER: |
| 633 |
|
| 634 |
DTV_ATSCMH_FIC_VER |
| 635 |
------------------ |
| 636 |
|
| 637 |
Used only on ATSC-MH. |
| 638 |
|
| 639 |
Version number of the FIC (Fast Information Channel) signaling data. |
| 640 |
|
| 641 |
FIC is used for relaying information to allow rapid service acquisition |
| 642 |
by the receiver. |
| 643 |
|
| 644 |
Possible values: 0, 1, 2, 3, ..., 30, 31 |
| 645 |
|
| 646 |
|
| 647 |
.. _DTV-ATSCMH-PARADE-ID: |
| 648 |
|
| 649 |
DTV_ATSCMH_PARADE_ID |
| 650 |
-------------------- |
| 651 |
|
| 652 |
Used only on ATSC-MH. |
| 653 |
|
| 654 |
Parade identification number |
| 655 |
|
| 656 |
A parade is a collection of up to eight MH groups, conveying one or two |
| 657 |
ensembles. |
| 658 |
|
| 659 |
Possible values: 0, 1, 2, 3, ..., 126, 127 |
| 660 |
|
| 661 |
|
| 662 |
.. _DTV-ATSCMH-NOG: |
| 663 |
|
| 664 |
DTV_ATSCMH_NOG |
| 665 |
-------------- |
| 666 |
|
| 667 |
Used only on ATSC-MH. |
| 668 |
|
| 669 |
Number of MH groups per MH subframe for a designated parade. |
| 670 |
|
| 671 |
Possible values: 1, 2, 3, 4, 5, 6, 7, 8 |
| 672 |
|
| 673 |
|
| 674 |
.. _DTV-ATSCMH-TNOG: |
| 675 |
|
| 676 |
DTV_ATSCMH_TNOG |
| 677 |
--------------- |
| 678 |
|
| 679 |
Used only on ATSC-MH. |
| 680 |
|
| 681 |
Total number of MH groups including all MH groups belonging to all MH |
| 682 |
parades in one MH subframe. |
| 683 |
|
| 684 |
Possible values: 0, 1, 2, 3, ..., 30, 31 |
| 685 |
|
| 686 |
|
| 687 |
.. _DTV-ATSCMH-SGN: |
| 688 |
|
| 689 |
DTV_ATSCMH_SGN |
| 690 |
-------------- |
| 691 |
|
| 692 |
Used only on ATSC-MH. |
| 693 |
|
| 694 |
Start group number. |
| 695 |
|
| 696 |
Possible values: 0, 1, 2, 3, ..., 14, 15 |
| 697 |
|
| 698 |
|
| 699 |
.. _DTV-ATSCMH-PRC: |
| 700 |
|
| 701 |
DTV_ATSCMH_PRC |
| 702 |
-------------- |
| 703 |
|
| 704 |
Used only on ATSC-MH. |
| 705 |
|
| 706 |
Parade repetition cycle. |
| 707 |
|
| 708 |
Possible values: 1, 2, 3, 4, 5, 6, 7, 8 |
| 709 |
|
| 710 |
|
| 711 |
.. _DTV-ATSCMH-RS-FRAME-MODE: |
| 712 |
|
| 713 |
DTV_ATSCMH_RS_FRAME_MODE |
| 714 |
------------------------ |
| 715 |
|
| 716 |
Used only on ATSC-MH. |
| 717 |
|
| 718 |
Reed Solomon (RS) frame mode. |
| 719 |
|
| 720 |
The acceptable values are defined by :c:type:`atscmh_rs_frame_mode`. |
| 721 |
|
| 722 |
|
| 723 |
.. _DTV-ATSCMH-RS-FRAME-ENSEMBLE: |
| 724 |
|
| 725 |
DTV_ATSCMH_RS_FRAME_ENSEMBLE |
| 726 |
---------------------------- |
| 727 |
|
| 728 |
Used only on ATSC-MH. |
| 729 |
|
| 730 |
Reed Solomon (RS) frame ensemble. |
| 731 |
|
| 732 |
The acceptable values are defined by :c:type:`atscmh_rs_frame_ensemble`. |
| 733 |
|
| 734 |
|
| 735 |
.. _DTV-ATSCMH-RS-CODE-MODE-PRI: |
| 736 |
|
| 737 |
DTV_ATSCMH_RS_CODE_MODE_PRI |
| 738 |
--------------------------- |
| 739 |
|
| 740 |
Used only on ATSC-MH. |
| 741 |
|
| 742 |
Reed Solomon (RS) code mode (primary). |
| 743 |
|
| 744 |
The acceptable values are defined by :c:type:`atscmh_rs_code_mode`. |
| 745 |
|
| 746 |
|
| 747 |
.. _DTV-ATSCMH-RS-CODE-MODE-SEC: |
| 748 |
|
| 749 |
DTV_ATSCMH_RS_CODE_MODE_SEC |
| 750 |
--------------------------- |
| 751 |
|
| 752 |
Used only on ATSC-MH. |
| 753 |
|
| 754 |
Reed Solomon (RS) code mode (secondary). |
| 755 |
|
| 756 |
The acceptable values are defined by :c:type:`atscmh_rs_code_mode`. |
| 757 |
|
| 758 |
|
| 759 |
.. _DTV-ATSCMH-SCCC-BLOCK-MODE: |
| 760 |
|
| 761 |
DTV_ATSCMH_SCCC_BLOCK_MODE |
| 762 |
-------------------------- |
| 763 |
|
| 764 |
Used only on ATSC-MH. |
| 765 |
|
| 766 |
Series Concatenated Convolutional Code Block Mode. |
| 767 |
|
| 768 |
The acceptable values are defined by :c:type:`atscmh_sccc_block_mode`. |
| 769 |
|
| 770 |
|
| 771 |
.. _DTV-ATSCMH-SCCC-CODE-MODE-A: |
| 772 |
|
| 773 |
DTV_ATSCMH_SCCC_CODE_MODE_A |
| 774 |
--------------------------- |
| 775 |
|
| 776 |
Used only on ATSC-MH. |
| 777 |
|
| 778 |
Series Concatenated Convolutional Code Rate. |
| 779 |
|
| 780 |
The acceptable values are defined by :c:type:`atscmh_sccc_code_mode`. |
| 781 |
|
| 782 |
.. _DTV-ATSCMH-SCCC-CODE-MODE-B: |
| 783 |
|
| 784 |
DTV_ATSCMH_SCCC_CODE_MODE_B |
| 785 |
--------------------------- |
| 786 |
|
| 787 |
Used only on ATSC-MH. |
| 788 |
|
| 789 |
Series Concatenated Convolutional Code Rate. |
| 790 |
|
| 791 |
Possible values are the same as documented on enum |
| 792 |
:c:type:`atscmh_sccc_code_mode`. |
| 793 |
|
| 794 |
|
| 795 |
.. _DTV-ATSCMH-SCCC-CODE-MODE-C: |
| 796 |
|
| 797 |
DTV_ATSCMH_SCCC_CODE_MODE_C |
| 798 |
--------------------------- |
| 799 |
|
| 800 |
Used only on ATSC-MH. |
| 801 |
|
| 802 |
Series Concatenated Convolutional Code Rate. |
| 803 |
|
| 804 |
Possible values are the same as documented on enum |
| 805 |
:c:type:`atscmh_sccc_code_mode`. |
| 806 |
|
| 807 |
|
| 808 |
.. _DTV-ATSCMH-SCCC-CODE-MODE-D: |
| 809 |
|
| 810 |
DTV_ATSCMH_SCCC_CODE_MODE_D |
| 811 |
--------------------------- |
| 812 |
|
| 813 |
Used only on ATSC-MH. |
| 814 |
|
| 815 |
Series Concatenated Convolutional Code Rate. |
| 816 |
|
| 817 |
Possible values are the same as documented on enum |
| 818 |
:c:type:`atscmh_sccc_code_mode`. |
| 819 |
|
| 820 |
|
| 821 |
.. _DTV-API-VERSION: |
| 822 |
|
| 823 |
DTV_API_VERSION |
| 824 |
=============== |
| 825 |
|
| 826 |
Returns the major/minor version of the Digital TV API |
| 827 |
|
| 828 |
|
| 829 |
.. _DTV-CODE-RATE-HP: |
| 830 |
|
| 831 |
DTV_CODE_RATE_HP |
| 832 |
================ |
| 833 |
|
| 834 |
Used on terrestrial transmissions. |
| 835 |
|
| 836 |
The acceptable values are defined by :c:type:`fe_transmit_mode`. |
| 837 |
|
| 838 |
|
| 839 |
.. _DTV-CODE-RATE-LP: |
| 840 |
|
| 841 |
DTV_CODE_RATE_LP |
| 842 |
================ |
| 843 |
|
| 844 |
Used on terrestrial transmissions. |
| 845 |
|
| 846 |
The acceptable values are defined by :c:type:`fe_transmit_mode`. |
| 847 |
|
| 848 |
|
| 849 |
.. _DTV-GUARD-INTERVAL: |
| 850 |
|
| 851 |
DTV_GUARD_INTERVAL |
| 852 |
================== |
| 853 |
|
| 854 |
The acceptable values are defined by :c:type:`fe_guard_interval`. |
| 855 |
|
| 856 |
.. note:: |
| 857 |
|
| 858 |
#. If ``DTV_GUARD_INTERVAL`` is set the ``GUARD_INTERVAL_AUTO`` the |
| 859 |
hardware will try to find the correct guard interval (if capable) and |
| 860 |
will use TMCC to fill in the missing parameters. |
| 861 |
#. Interval ``GUARD_INTERVAL_1_64`` is used only for DVB-C2. |
| 862 |
#. Interval ``GUARD_INTERVAL_1_128`` is used for both DVB-C2 and DVB_T2. |
| 863 |
#. Intervals ``GUARD_INTERVAL_19_128`` and ``GUARD_INTERVAL_19_256`` are |
| 864 |
used only for DVB-T2. |
| 865 |
#. Intervals ``GUARD_INTERVAL_PN420``, ``GUARD_INTERVAL_PN595`` and |
| 866 |
``GUARD_INTERVAL_PN945`` are used only for DMTB at the present. |
| 867 |
On such standard, only those intervals and ``GUARD_INTERVAL_AUTO`` |
| 868 |
are valid. |
| 869 |
|
| 870 |
.. _DTV-TRANSMISSION-MODE: |
| 871 |
|
| 872 |
DTV_TRANSMISSION_MODE |
| 873 |
===================== |
| 874 |
|
| 875 |
|
| 876 |
Used only on OFTM-based standards, e. g. DVB-T/T2, ISDB-T, DTMB. |
| 877 |
|
| 878 |
Specifies the FFT size (with corresponds to the approximate number of |
| 879 |
carriers) used by the standard. |
| 880 |
|
| 881 |
The acceptable values are defined by :c:type:`fe_transmit_mode`. |
| 882 |
|
| 883 |
.. note:: |
| 884 |
|
| 885 |
#. ISDB-T supports three carrier/symbol-size: 8K, 4K, 2K. It is called |
| 886 |
**mode** on such standard, and are numbered from 1 to 3: |
| 887 |
|
| 888 |
==== ======== ======================== |
| 889 |
Mode FFT size Transmission mode |
| 890 |
==== ======== ======================== |
| 891 |
1 2K ``TRANSMISSION_MODE_2K`` |
| 892 |
2 4K ``TRANSMISSION_MODE_4K`` |
| 893 |
3 8K ``TRANSMISSION_MODE_8K`` |
| 894 |
==== ======== ======================== |
| 895 |
|
| 896 |
#. If ``DTV_TRANSMISSION_MODE`` is set the ``TRANSMISSION_MODE_AUTO`` |
| 897 |
the hardware will try to find the correct FFT-size (if capable) and |
| 898 |
will use TMCC to fill in the missing parameters. |
| 899 |
|
| 900 |
#. DVB-T specifies 2K and 8K as valid sizes. |
| 901 |
|
| 902 |
#. DVB-T2 specifies 1K, 2K, 4K, 8K, 16K and 32K. |
| 903 |
|
| 904 |
#. DTMB specifies C1 and C3780. |
| 905 |
|
| 906 |
|
| 907 |
.. _DTV-HIERARCHY: |
| 908 |
|
| 909 |
DTV_HIERARCHY |
| 910 |
============= |
| 911 |
|
| 912 |
Used only on DVB-T and DVB-T2. |
| 913 |
|
| 914 |
Frontend hierarchy. |
| 915 |
|
| 916 |
The acceptable values are defined by :c:type:`fe_hierarchy`. |
| 917 |
|
| 918 |
|
| 919 |
.. _DTV-STREAM-ID: |
| 920 |
|
| 921 |
DTV_STREAM_ID |
| 922 |
============= |
| 923 |
|
| 924 |
Used on DVB-C2, DVB-S2, DVB-T2 and ISDB-S. |
| 925 |
|
| 926 |
DVB-C2, DVB-S2, DVB-T2 and ISDB-S support the transmission of several |
| 927 |
streams on a single transport stream. This property enables the digital |
| 928 |
TV driver to handle substream filtering, when supported by the hardware. |
| 929 |
By default, substream filtering is disabled. |
| 930 |
|
| 931 |
For DVB-C2, DVB-S2 and DVB-T2, the valid substream id range is from 0 to |
| 932 |
255. |
| 933 |
|
| 934 |
For ISDB, the valid substream id range is from 1 to 65535. |
| 935 |
|
| 936 |
To disable it, you should use the special macro NO_STREAM_ID_FILTER. |
| 937 |
|
| 938 |
Note: any value outside the id range also disables filtering. |
| 939 |
|
| 940 |
|
| 941 |
.. _DTV-DVBT2-PLP-ID-LEGACY: |
| 942 |
|
| 943 |
DTV_DVBT2_PLP_ID_LEGACY |
| 944 |
======================= |
| 945 |
|
| 946 |
Obsolete, replaced with DTV_STREAM_ID. |
| 947 |
|
| 948 |
|
| 949 |
.. _DTV-ENUM-DELSYS: |
| 950 |
|
| 951 |
DTV_ENUM_DELSYS |
| 952 |
=============== |
| 953 |
|
| 954 |
A Multi standard frontend needs to advertise the delivery systems |
| 955 |
provided. Applications need to enumerate the provided delivery systems, |
| 956 |
before using any other operation with the frontend. Prior to its |
| 957 |
introduction, FE_GET_INFO was used to determine a frontend type. A |
| 958 |
frontend which provides more than a single delivery system, |
| 959 |
FE_GET_INFO doesn't help much. Applications which intends to use a |
| 960 |
multistandard frontend must enumerate the delivery systems associated |
| 961 |
with it, rather than trying to use FE_GET_INFO. In the case of a |
| 962 |
legacy frontend, the result is just the same as with FE_GET_INFO, but |
| 963 |
in a more structured format. |
| 964 |
|
| 965 |
The acceptable values are defined by :c:type:`fe_delivery_system`. |
| 966 |
|
| 967 |
|
| 968 |
.. _DTV-INTERLEAVING: |
| 969 |
|
| 970 |
DTV_INTERLEAVING |
| 971 |
================ |
| 972 |
|
| 973 |
Time interleaving to be used. |
| 974 |
|
| 975 |
The acceptable values are defined by :c:type:`fe_interleaving`. |
| 976 |
|
| 977 |
|
| 978 |
.. _DTV-LNA: |
| 979 |
|
| 980 |
DTV_LNA |
| 981 |
======= |
| 982 |
|
| 983 |
Low-noise amplifier. |
| 984 |
|
| 985 |
Hardware might offer controllable LNA which can be set manually using |
| 986 |
that parameter. Usually LNA could be found only from terrestrial devices |
| 987 |
if at all. |
| 988 |
|
| 989 |
Possible values: 0, 1, LNA_AUTO |
| 990 |
|
| 991 |
0, LNA off |
| 992 |
|
| 993 |
1, LNA on |
| 994 |
|
| 995 |
use the special macro LNA_AUTO to set LNA auto |
| 996 |
|
| 997 |
|
| 998 |
.. _DTV-SCRAMBLING-SEQUENCE-INDEX: |
| 999 |
|
| 1000 |
DTV_SCRAMBLING_SEQUENCE_INDEX |
| 1001 |
============================= |
| 1002 |
|
| 1003 |
Used on DVB-S2. |
| 1004 |
|
| 1005 |
This 18 bit field, when present, carries the index of the DVB-S2 physical |
| 1006 |
layer scrambling sequence as defined in clause 5.5.4 of EN 302 307. |
| 1007 |
There is no explicit signalling method to convey scrambling sequence index |
| 1008 |
to the receiver. If S2 satellite delivery system descriptor is available |
| 1009 |
it can be used to read the scrambling sequence index (EN 300 468 table 41). |
| 1010 |
|
| 1011 |
By default, gold scrambling sequence index 0 is used. |
| 1012 |
|
| 1013 |
The valid scrambling sequence index range is from 0 to 262142. |