| 1 |
.. SPDX-License-Identifier: GPL-2.0 |
| 2 |
|
| 3 |
========================= |
| 4 |
octeontx2 devlink support |
| 5 |
========================= |
| 6 |
|
| 7 |
This document describes the devlink features implemented by the ``octeontx2 AF, PF and VF`` |
| 8 |
device drivers. |
| 9 |
|
| 10 |
Parameters |
| 11 |
========== |
| 12 |
|
| 13 |
The ``octeontx2 PF and VF`` drivers implement the following driver-specific parameters. |
| 14 |
|
| 15 |
.. list-table:: Driver-specific parameters implemented |
| 16 |
:widths: 5 5 5 85 |
| 17 |
|
| 18 |
* - Name |
| 19 |
- Type |
| 20 |
- Mode |
| 21 |
- Description |
| 22 |
* - ``mcam_count`` |
| 23 |
- u16 |
| 24 |
- runtime |
| 25 |
- Select number of match CAM entries to be allocated for an interface. |
| 26 |
The same is used for ntuple filters of the interface. Supported by |
| 27 |
PF and VF drivers. |
| 28 |
|
| 29 |
The ``octeontx2 AF`` driver implements the following driver-specific parameters. |
| 30 |
|
| 31 |
.. list-table:: Driver-specific parameters implemented |
| 32 |
:widths: 5 5 5 85 |
| 33 |
|
| 34 |
* - Name |
| 35 |
- Type |
| 36 |
- Mode |
| 37 |
- Description |
| 38 |
* - ``dwrr_mtu`` |
| 39 |
- u32 |
| 40 |
- runtime |
| 41 |
- Use to set the quantum which hardware uses for scheduling among transmit queues. |
| 42 |
Hardware uses weighted DWRR algorithm to schedule among all transmit queues. |
| 43 |
* - ``npc_mcam_high_zone_percent`` |
| 44 |
- u8 |
| 45 |
- runtime |
| 46 |
- Use to set the number of high priority zone entries in NPC MCAM that can be allocated |
| 47 |
by a user, out of the three priority zone categories high, mid and low. |
| 48 |
* - ``npc_def_rule_cntr`` |
| 49 |
- bool |
| 50 |
- runtime |
| 51 |
- Use to enable or disable hit counters for the default rules in NPC MCAM. |
| 52 |
Its not guaranteed that counters gets enabled and mapped to all the default rules, |
| 53 |
since the counters are scarce and driver follows a best effort approach. |
| 54 |
The default rule serves as the primary packet steering rule for a specific PF or VF, |
| 55 |
based on its DMAC address which is installed by AF driver as part of its initialization. |
| 56 |
Sample command to read hit counters for default rule from debugfs is as follows, |
| 57 |
cat /sys/kernel/debug/cn10k/npc/mcam_rules |
| 58 |
* - ``nix_maxlf`` |
| 59 |
- u16 |
| 60 |
- runtime |
| 61 |
- Use to set the maximum number of LFs in NIX hardware block. This would be useful |
| 62 |
to increase the availability of default resources allocated to enabled LFs like |
| 63 |
MCAM entries for example. |
| 64 |
|
| 65 |
The ``octeontx2 PF`` driver implements the following driver-specific parameters. |
| 66 |
|
| 67 |
.. list-table:: Driver-specific parameters implemented |
| 68 |
:widths: 5 5 5 85 |
| 69 |
|
| 70 |
* - Name |
| 71 |
- Type |
| 72 |
- Mode |
| 73 |
- Description |
| 74 |
* - ``unicast_filter_count`` |
| 75 |
- u8 |
| 76 |
- runtime |
| 77 |
- Set the maximum number of unicast filters that can be programmed for |
| 78 |
the device. This can be used to achieve better device resource |
| 79 |
utilization, avoiding over consumption of unused MCAM table entries. |